The Dserve DSRV9703C is a 9.7" A10 tablet with a 1024x768 ips LCD,
1G RAM, 4GB flash, a Focaltech FT5406EE8 touchscreen and rtl8188ctv wifi.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The yones toptech bs1078-v2 is a 10.1" tablet without any clear markings on
the outside, but 'YONESTOPTECH-BS1078' written on the PCB silkscreen.
It features a 16:9 1024:600 LCD, A31s SoC, 1GB RAM, 8G NAND, silead gsl3675
touchscreen and a RTL8723AS wifi chip:
https://linux-sunxi.org/Yones_Toptech_BS1078_V2
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Sinlinx A31s SDK is a A31s based module/baseboard development kit.
The core module has the SoC, PMIC, DRAM, eMMC and supporting components.
There are also pads for UART0, JTAG and I2S.
The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0
hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume
buttons, RS232 style UART and USB OTG (though VBUS is not connected).
Various headers are available for other addon modules, such as SDIO
WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add defconfig for the multi board device based on the
Allwinner A20 SoC. It contains the A20 Itead Core module and a
base board for the external interfaces.
The core module comes with 4GB NAND and 1GB DDR RAM.
The base board to which the core board is connected provides
3 USB 2.0 Host ports, 1 USB 2.0 OTG, 1 uSD slot, 10/100 Ethernet
port, HDMI, IR receiver, SPDIF and a 32-pin GPIO header. This
header expands the features of core board by exposing the VGA pins,
audio In/Out pins, SATA, SPI, I2C, UARTS, USB-OTG and power..
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cubietruck Plus is a A83T/H8 based development board. The board has
standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host
via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet,
WiFi, headphone out / mic in, and various GPIO headers.
The board also has an EEPROM on i2c0 which holds the MAC address.
DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20
is connected to the reset control of the PHY. EMAC is not actually
supported yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Polaroid MID2809PXE4 is a 9" tablet which is clearly marked
Polaroid MID2809PXE4 on the back. It features a 9" 16:9 800x480 LCD,
A23 Soc, 1GB RAM, 8GB NAND, gsl3670 touchscreen and esp8089 wifi.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Difrnce dit4350 tablet is a tiny tablet with a 4.3" 16:9 480x272 LCD,
A13 SoC, 512M RAM, 4G NAND, solomon systech ssd2532qn6 touchscreen at
i2c1 address 0x48, Memsic MXC622X accelerometer at i2c1 address 0x15 and
rtl8188etv wifi.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The colorfly e708 q1 is a 7" tablet which is clearly marked as colorfly
e708 q1 on the back. It features a 9:16 800x1280 IPS LCD, A31s SoC,
1GB RAM, 8G NAND, ilitek 2139qt004 touchscreen on i2c-1 addr 0x41,
stk8313 accelerometer on i2c-2 addr 0x22 and a rtl8188etv wifi chip.
The added dts is identical to the dts submitted to the upstream kernel,
note this commit also syncs axp22x.dtsi and sun6i-a31.dtsi with the
upstream kernel as the added dts depends on these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The current CONFIG names like "CONFIG_ARCH_UNIPHIER_PH1_PRO4" is too
long. It would not hurt to drop "PH1_" because "UNIPHIER_" already
well specifies the SoC family. Also, rename files for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Introduce CONFIG_RTL8169 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Stephen Warren <swaren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Introduce CONFIG_RTL8139 in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: Fixup MPC8641HPCN* and r2dplus configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some boards' defconfig files are out of order. Clean this up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch makes the following changes to the SR1500 board port:
- Update defconfig to support SPI NOR (use make savedefconfig).
- Increase SPI speed to a maximum of 100MHz for faster system
bootup.
- Change environment location, so that its not between SPL and
main U-Boot. This way the combined SPL / U-Boot image can
be used for updates.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Now that the drivers used by sandbox support CONFIG_BLK, we can switch
sandbox over to use driver model for block devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
This patch adds support for the congatec conga-QA3/E3845-4G eMMC8 SoM,
installed on the congatec Qseven 2.0 evaluation carrier board
(conga-QEVAL).
Its port is very similar to the MinnowboardMAX port and also uses
the Intel FSP as described in doc/README.x86.
Currently supported are the following interfaces / devices:
- UART (via Winbond legacy SuperIO chip on carrier board)
- Ethernet (PCIe Intel I210 / E1000)
- SPI including SPI NOR as boot-device
- USB 2.0
- SATA via U-Boot SCSI IF
- eMMC
- Video (HDMI output @ 800x600)
- PCIe
Not supported yet is:
- I2C
- USB 3.0
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This adds basic support for chromebook_samus. This is the 2015 Pixel and
is based on an Intel broadwell platform.
Supported so far are:
- Serial
- SPI flash
- SDRAM init (with MRC cache)
- SATA
- Video (on the internal LCD panel)
- Keyboard
Various less-visible drivers are provided to make the above work (e.g. PCH,
power control and LPC).
The platform requires various binary blobs which are documented in the
README. The major missing feature is USB3 since the existing U-Boot support
does not work correctly with Intel XHCI controllers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rather than setting up the pin configuration in the GPIO driver, use the
new pinctrl driver to do it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have all the bits and pieces ready for EFI payload loading
support, hook them up in Makefiles and KConfigs so that we can build.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
[trini: Enable only when we of OF_LIBFDT, disable on kwb and colibri_pxa270]
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds support for the MUSB USB dual-role controller in peripheral mode,
with configuration options for the fastboot USB gadget.
At this point, flashing the internal eMMC is support.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The Amazon Kindle Fire (first generation) codename kc1 is a tablet that was
released by Amazon back in 2011.
It is using an OMAP4430 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This is based on the davinci da850evm. It can boot from either the
on-board 16MB flash or from a microSD card. It also reads board
information from an I2C EEPROM.
The EV3 itself initally boots from write-protected EEPROM, so no
u-boot SPL is needed.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable support for PMMC the TI power processor on K2G. This processor
manages all power management related activities on the SoC and and
allows the Operating Systems on compute processors such as ARM, DSP to
offload the power logic away into the power processor.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
Kconfig options must defined in the defconfig files. Since RSA_SOFTWARE_EXP
relies on CONFIG_DM, unless it is set in kconfig we cannot enable RSA.
Remove the hacks which enable CONFIG_DM in header files and update the
defconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Various boards have the wrong Kconfig ordering now. To avoid a misleading
diff in the next patch, reorder the configuration correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for GE B450v3, B650v3 and B850v3 boards. The boards
are based on Advantech BA16 module which has a i.MX6D processor.
The boards support:
- FEC Ethernet
- USB Ports
- SDHC and MMC boot
- SPI NOR
- LVDS and HDMI display
Basic information about the module:
- Module manufacturer: Advantech
- CPU: Freescale ARM Cortex-A9 i.MX6D
- SPECS:
Up to 2GB Onboard DDR3 Memory;
Up to 16GB Onboard eMMC NAND Flash
Supports OpenGL ES 2.0 and OpenVG 1.1
HDMI, 24-bit LVDS
1x UART, 2x I2C, 8x GPIO,
4x Host USB 2.0 port, 1x USB OTG port,
1x micro SD (SDHC),1x SDIO, 1x SATA II,
1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
MIPS EL boards should define CONFIG_USE_PRIVATE_LIBGCC=y to work
with EB-only toolchains like the one from kernel.org. If one do
not globally set CONFIG_USE_PRIVATE_LIBGCC=y, the build fails with:
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_lshrdi3.o): compiled for a big endian system and target is little endian
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_lshrdi3.o): endianness incompatible with that of the selected emulation
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: failed to merge target specific data of file /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_lshrdi3.o)
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_ashldi3.o): compiled for a big endian system and target is little endian
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_ashldi3.o): endianness incompatible with that of the selected emulation
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: failed to merge target specific data of file /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_ashldi3.o)
/work/git-trees/u-boot-mips/Makefile:1171: recipe for target 'u-boot' failed
One example for a failing build is Travis CI.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Purna Chandra Mandal <purna.mandal@microchip.com>
This introduces some minor cleanups, regarding aspects such as board name, code
and headers organization as well as deprecated and missing config options.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The chains of "depends on <SoC_name>" in the current Kconfig is
clumsy. The idea here is to allow users to choose a SoC group first
(SoC group consists of some SoCs that can coexist in one binary).
Then, allow to enable/disable each SoC support in the selected SoC
group. This makes the Kconfig menu clearer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
PH1-Pro5 support and ProXstream2/PH1-LD6b support can coexist in one
image and there is bit more room in SPL to accommodate all of them.
Merge uniphier_pro5_defconfig into uniphier_pxs2_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable the driver in all UniPhier defconfig files and add some
needed defines to the common files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Define prompt for cm-t43.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add full support for SPI flash chips to future-proof U-Boot for cm-t43.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move CONFIG_DM_SERIAL to cm_t43_defconfig. This forces us to update the
CONFIG_SYS_NS16550_REG_SIZE value for SPL.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
We drop everything possible things from board headerfiles and replace
this functionality with responsible settings in Kconfig (_defconfig).
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is no need to have some specific prompt, so we drop this within
defconfigs.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported
in SD boot now. For the customer's demand, QSPI needs to be supported
in SD boot too.
This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021aqds_sdcard_ifc_defconfig
is used to support IFC in SD boot and ls1021aqds_sdcard_qspi_defconfig
is used to support QSPI in SD boot.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Convert ls1021aqds_nor_lpuart and ls1021aqds_ddr4_nor_lpuart
to driver model suport. Enable lpuart port driver.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.
This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Split duart configuration as device tree file. Move /chosen node
out of board commone device tree. Convert ls1021aqds nor and SD
configurations to driver model support (qspi already uses DM).
Enable ns16550 DM serial driver for nor configurations.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
enable dma driver model for am437x_sk_evm as ti-edma3 supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
In current design, if any peripheral was assigned to both A7 and M4,
it will receive ipg_stop or ipg_wait when any of the 2 platforms
enter low power mode. We will have a risk that, if A7 enter wait,
M4 enter stop, peripheral will have chance to get ipg_stop and ipg_wait
asserted same time. Also if M4 enters stop mode, A7 will have no
chance to access the peripheral.
There are 26 peripherals affected by this IC issue:
SIM2(sim2/emvsim2)
SIM1(sim1/emvsim1)
UART1/UART2/UART3/UART4/UART5/UART6/UART7
SAI1/SAI2/SAI3
WDOG1/WDOG2/WDOG3/WDOG4
GPT1/GPT2/GPT3/GPT4
PWM1/PWM2/PWM3/PWM4
ENET1/ENET2
Software Workaround:
The solution is to set the peripherals to Domain0 by A core, since A core
in Domain0. The peripherals which will be used by M4, will be set to Domain1
by M4.
For example, A core set WDOG4 to domain0, but when M4 boots up, M4 will
set WDOG4 to domain1, because M4 will use WDOG4.
So the peripherals are not shared by them. This way requires
the uboot implemented the RDC driver and set the 26 IPs above
to domain 0 only. M4 image will set the M4 to domain 1 and
set peripheral which it will use to domain 1.
This patch enables the CONFIG_IMX_RDC and CONFIG_IMX_BOOTAUX for
i.MX7D SABRESD board, and setup the 26 IP resources to domain 0.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This adds basic support to Intel Cougar Canyon 2 board, a board
based on Chief River platform with an Ivy Bridge processor and
a Panther Point chipset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
ARC core could be configured with different L1 and L2 (AKA SLC) cache
line lengths. At least these values are possible and were really used:
32, 64 or 128 bytes.
Current implementation requires cache line to be selected upon U-Boot
configuration and then it will only work on matching hardware. Indeed
this is quite efficient because cache line length gets hardcoded during
code compilation. But OTOH it makes binary less portable.
With this commit we allow U-Boot to determine real L1 cache line length
early in runtime and use this value later on. This extends portability
of U-Boot binary a lot.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The Versatile Industrial Communication platform is a community oriented
board from Landis + Gyr. It comes with:
- an RS-485 port
- 2 Ethernet ports
- a wireless M-BUS
- a 4G modem
- a 4MB SPI flash
- a 4GB eMMC
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[rebase on current TOT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add support for DENX MA5D4 SoM and MA5D4EVK board, based on the
Atmel SAMA5D4 SoC. The SoM contains the SoC, eMMC, SPI NOR, SPI
CAN controllers and DRAM, the baseboard contains UART connectors,
ethernet port, microSD slot, LCD header, 2x CAN connector and a
lot of expansion headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
New features for smartweb:
* switch to hush command parser
* change autoboot stop to <ESC><ESC>
* allow to write ethaddr
Signed-off-by: Matthias Michel <matthias.michel@siemens.com>
Reviewed-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Move this option to Kconfig and clean up the header files. Adjust the only
user (the LCD driver) to work with the new driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move this driver over to use driver model. This involves rearranging the
code somewhat. The effect is that everything is run from the probe() method.
Boards which use this are fixed up, but only seaboard is tested.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This option refers only to the tegra20 video driver, so name it as such
to avoid confusion with tegra124.
Also move this option to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Adjust the driver to use driver model. The SOR becomes a bridge device. We
use the normal simple_panel driver to handle the display itself. We also
need to enable some options such as regulators, PWMs and DM_VIDEO itself.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The UniPhier EHCI driver (drivers/usb/host/ehci-uniphier.c) does
nothing special but set the base address and handle reset/clock.
Since commit 4feefdcfe9 ("usb: add clock support for generic EHCI"),
the generic one (drivers/usb/host/ehci-generic.c) can do those, too.
We no longer need to stick to the dedicated driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add nand driver support for zynqmp. The Nand
controller used in ZynqMP is Arasan Nand Flash
controller.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[scottwood: Fix checkpatch warning]
Signed-off-by: Scott Wood <oss@buserror.net>
enable net driver model for k2g evm as keystone_net supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
enable net driver model for k2e evm as keystone_net supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
enable net driver model for k2l evm as keystone_net supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
enable net driver model for k2hk evm as keystone_net supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The defconfig patch will enable the the SPL and NAND settings.
The update to Kconfig will allow the SPL to configured in and
built.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The option was renamed to CONFIG_CONSOLE_ROTATION and Rockchip boards
were not updated. However this option is is not needed by default for
Rockchip since we don't need a rotated console for current boards. So just
remove the old option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This board uses RTL8169 which is a driver model ethernet driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move some #undef from efi-x86.h to efi-x86_defconfig as these are
already Kconfig options.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Let's go with pure DT solution for board's
based on NXP/Freescale Vybrid platform.
- Merge the DT defconfig with non-DT defconfig for Toradex
Colibri VF50/VF61 and drop the non-DT defconfig.
- Update the legacy defconfigs for NXP/Freescale VF610 Tower
Board with DT.
- Update the legacy defconfigs for Phytec phyCORE-vybrid
Board with DT.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Initial version for mx6sx SABREAUTO board support with features:
PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander.
Signed-off-by: Ye Li <ye.li@nxp.com>
The sama5d2 Xplained SPL supports the boot medias: spi flash
and SD Card.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
This adds ethernet, TFTP support for PIC32MZ[DA] Starter Kit. Also
custom environment variables/scripts are added to help boot from network.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Enable MMC, SDHCI, FAT_FS support for PIC32MZ[DA] StarterKit.
Also add custom scripts, rules to boot Linux from microSD card.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
This adds support for Microchip PIC32MZ[DA] StarterKit board
based on a PIC32MZ[DA] family of microcontroller.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Enable this feature so that truetype fonts can be used on the sandbox
console. Update the tests to select the normal/rotated console when needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Enable the U-Boot Driver Model(DM) to use the Freescale QSPI driver.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI and IFC are pin-multiplexed on LS1043A. So we use
ls1043aqds_sdcard_ifc_defconfig to support IFC in SD boot and
ls1043aqds_sdcard_qspi_defconfig to support QSPI in SD boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add lpuart support using the driver model.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Move new /chosen node out of the board device tree.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
If the xparameters file contains a LL_TEMAC definition compile its
driver and the net commands.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
xilinx_uartlite has been ported to DM, this patch makes the
xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new
DM driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Define CONFIG_SYS_PROMPT for all Zynq boards
It was removed by:
"kconfig: add config option for shell prompt"
(sha1: 181bd9dc61)
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add PHYLIB and MII dependencies and enable it by default for Microblaze.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- Move config option out of board file.
- Remove uartlite address from config file
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Remove redundant defconfig file. Boot via flash can be configured via
Kconfig.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Remove redundant defconfig file. Boot via flash can be configured via
Kconfig.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of xilinx-ppc440
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of the xilinx-ppc405
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
ml507 is just a specialized version of the xilinx-ppc440-generic
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for the Armada XP (MV78260) based theadorable
board. Its equipped with onboard DDR3, UART, ethernet, I2C, SPI NOR,
LCD and SATA (SSD) interfaces / devices.
Two defconfigs are added:
theadorable_defconfig:
The production U-Boot version with a stripped down drivers and feature
list. This removes networking, USB and PCI support.
theadorable_debug_defconfig:
The debugging / testing U-Boot version with full support for all drivers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
According to the Bananapro schematic VDD25-SATA either comes from a
dedicated WL2003E25-5 LTO, or it is connected to LDO4 via a
0 Ohm resistor.
In practice it seems that LDO4 is used, so enable it and set it to 2.5V.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The LDO settings in this defconfig are either wrong (ALDOs must not be 0)
or the same as Kconfig defaults.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add dts and defconfig for Banana-pi M3 board.
It has 2G LPDDR3, UART, ethernet, USB, HDMI, USB Sata, MIPI DSI,
mic, AP6212 Wifi, etc on it.
It is paired with AXP813 PMIC which is almost same as AXP818.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com: rename to Sinovoip_BPI_M3_defconfig/sun8i-a83t-sinovoip-bpi-m3.dts]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Enabling CONFIG_DISPLAY breaks building for some architectures
(microblaze-generic), so we disable CONFIG_DISPLAY in Kconfig
by default and enable this option in defconfigs. CONFIG_DISPLAY
depends on CONFIG_I2C_EDID, so add and enable it in defconfigs, too.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Each system controller can have a number to identify it. It can then be
accessed using syscon_get_by_driver_data(). Put this in a shared header
file and update the only current user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We will use a system controller to model the Intel Management Engine. Enable
this for link.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move the init code into the I2C driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The existing ivybridge code predates the normal multi-core CPU init, and
it is not used. Remove it and add CPU nodes to the device tree so that all
four CPUs are set up. Also enable the 'cpu' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This board includes an RK3288 SoC on a SOM. It can be mounted on a
base-board which provides a wide range of peripherals.
So far this is verified to boot to a prompt from a microSD card. The serial
console works as well as HDMI.
Thanks to Tom Cubie for sending me a board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable these devices using the VOPL video output device. We explicitly
disable VOPB in the device tree to avoid it taking over. Since this device
has an LCD display this comes up by default. If the display fails for some
reason then it will attempt to use HDMI. It is possible to force it to fail
(and thus fall back to HDMI) by puting 'return -EPERM' at the top of
rk_edp_probe(). For now there is no easy way to select between the two.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a feature which speeds up the CPU to full speed in SPL to minimise
boot time. This is only supported for certain boards (at present only
jerry).
Signed-off-by: Simon Glass <sjg@chromium.org>
The current DisplayPort uclass is too specific. The operations it provides
are shared with other types of output devices, such as HDMI and LVDS LCD
displays.
Generalise the uclass so that it can be used with these devices as well.
Adjust the uclass to handle the EDID reading and conversion to
display_timing internally.
Also update nyan-big which is affected by this.
Signed-off-by: Simon Glass <sjg@chromium.org>
To reduce the SPL image size, drop the LED features. Jerry does not have
an LED and we can leave out GPIO support also.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use the same peripheral ID for clocks and pinctrl. While this
works it is probably better to use the device tree clock binding ID for
clocks. We can use the clk_get_by_index() function to find this.
Update the clock drivers and the code that uses them.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is defined in the device tree in Linux. Copy over the settings so that
this can be used instead of hard-coding the reset line.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Heiko Schocher <hs@denx.de>
Test that text is displayed correctly when the console is rotated.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Now that driver model support is available, convert sandbox over to use it.
We can remove a few of the special hooks that sandbox currently has.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Move this option to Kconfig. This is quite simple as only sandbox uses the
driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Convert ls1021atwr_nor_lpuart to driver model support. As a start,
enable lpuart serial port driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Tested-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Simon Glass <sjg@chromium.org>
LPUART is seen on Freescale VF610 and QorIQ Layerscape devices.
Create a Kconfig option and move it to defconfig for all boards
that have this serial driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Simon Glass <sjg@chromium.org>
Convert ls1021atwr_nor to driver model support. As a start, enable
ns16550 serial port driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable timer driver model for dra74_evm_defconfig as omap-timer
supports driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable timer driver model for dra72_evm_defconfig as omap-timer
supports driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable timer driver model for am335x_gp_evm as omap-timer supports
driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable timer driver model for am335x_boneblack_vboot as
omap-timer supports driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable timer driver model for am437x_gp_evm as omap-timer supports
driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable timer driver model for am437x_sk_evm as omap-timer supports
driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On startup, the BeagleBone family of boards can occationally halt at
the U-Boot prompt. Due to U-Boot receiving random data on the usart.
Migrate BeagleBone based boards to use CONFIG_AUTOBOOT_KEYED, user
will now have to enter the <SPACE> key to get to U-Boot prompt
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Craig McQueen <craig.mcqueen@innerrange.com>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_NET_RANDOM_ETHADDR to generate a random MAC address
when ETHADDR is not set.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This is how CONFIG options are defined by Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
For historical reason, CONFIG_SYS_TEXT_BASE has been specified
in various ways:
[1] by board/${VENDOR}/${BOARD}/config.mk
[2] by CONFIG_SYS_EXTRA_OPTIONS
(This was "options" field of boards.cfg before Kconfig conversion)
[3] by include/configs/${BOARD}.h
[4] by configs/${BOARD}_defconfig
Most of M68K boards use either [1] or [2], both of which we want to
deprecate. Switch them into [4], which is the newest way (Kconfig).
We still allow [3] too, because it is still used by many boards and
we expect much time for conversion.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Angelo Dureghello <angelo at sysam.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Both of these boards are very close to their limit and with some toolchains
such as gcc 5.x are too large. Switch to tiny printf to reclaim some size.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enabling this function always removes some class of string saftey issues.
The size change here in general is about 400 bytes and this seems a reasonable
trade-off.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds support for the MV78230 based DS414 NAS by Synology. The
relevant bits have been extracted from the 'synogpl-5004-armadaxp'
package Synology kindly published, garnished with a fair amount of
trial-and-error.
Sadly, support is far from perfect. The major parts I have failed in
are SATA and XHCI support. Details about these and some other things
follow:
Device Tree
-----------
The device tree file armada-xp-synology-ds414.dts has been copied from
Linux and enhanced by recent U-Boot specific changes to
armada-xp-gp.dts.
SATA Support
------------
There is a Marvell 88SX7042 controller attached to PCIe which is
supported by Linux's sata_mv driver but sadly not U-Boot's sata_mv.
I'm not sure if extending the latter to support PCI devices is worth the
effort at all. Porting sata_mv from Linux exceeded my brain's
capacities. :(
XHCI Support
------------
There is an EtronTech EJ168A XHCI controller attached to PCIe which
drives the two rear USB3 ports. After a bit of playing around I managed
to get it recognized by xhci-pci, but never was able to access any
devices attached to it. Enabling it in ds414 board config shows that it
does not respond to commands for whatever reason. The (somewhat) bright
side to it is that it is not even supported in Synology's customized
U-Boot, but that also means nowhere to steal the relevant bits from.
EHCI Support
------------
This seems functional after issuing 'usb start'. At least it detects USB
storage devices, and IIRC reading from them was OK. OTOH Linux fails to
register the controller if 'usb start' wasn't given before in U-Boot.
According to Synology sources, this board seems to support USB device
(gadget?) mode. Though I didn't play around with it.
PCIe Support
------------
This is fine, but trying to gate the clocks of unused lanes will hang
PCI enum. In addition to that, pci_mvebu seems not to support DM_PCI.
DDR3 Training
-------------
Marvell/Synology uses eight PUPs instead of four. Does not look like
this is meant to be customized in mainline U-Boot at all. OTOH I have
no idea what a "PUP" actually is.
PEX Init
--------
Synology uses different values than mainline U-Boot with this patch:
pex_max_unit_get returns 2, pex_max_if_get returns 7 and
max_serdes_lines is set to 7. Not changing this seems to not have an
impact, although I'm not entirely sure it does not cause issues I am not
aware of.
Static Environment
------------------
This allows to boot stock Synology firmware at least. In order to be a
little more flexible when it comes to booting custom kernels, do not
only load zImage partition, but also rd.gz into memory. This way it is
possible to use about 7MB for kernel with piggyback initramfs.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
By removing CONFIG_SYS_MALLOC_CLEAR_ON_INIT, the bootup time is a bit
faster.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic support for the SolidRun ClearFog Armada 38x based
board to mainline U-Boot. Supported interfaces / devices are:
- DDR3
- UART
- MMC
- Ethernet port 0 (connected to dedicated PHY)
- I2C
The included DT source was taken from Russell King's ftp server:
http://www.home.arm.linux.org.uk/~rmk/clearfog/
With only minor modifications, like the addition of some aliases and the
"u-boot,dm-pre-reloc" property.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This is needed for the upcoming ethernet DM conversion of the maxbcm
board. The configuration of the PHY is then extracted from the DT
instead of using the defines from the config header.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.
This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.
Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:
arch/arm/cpu/u-boot-spl.lds
This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
This patch re-enables the setexpr command, I don't really understand
why it got excluded in the first place.
setexpr can be used e.g. to implement failed-boot-counters and
failovers to rescue firmware.
Signed-off-by: Marco Schuster <m.schuster91@googlemail.com>
For NXP LPC32xx boards the change enables SPL_DM option, this allows
to use any driver model UART driver in SPL images, hence a restriction
on HSUART in SPL image is removed and well as definitions for non-DM
NS16550 driver, its DM version is used instead.
Because SPL_DM requires malloc(), enable CONFIG_SPL_SYS_MALLOC_SIMPLE
for LPC32xx boards.
The change adds about 5KB to the resulting SPL image (for devkit3250
board SPL image is increased from 10672 to 15608 bytes).
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On NXP LPC32xx platform for non-SPL builds the change adds
standard (NS16550) and high-speed UARTs to driver model.
Due to specific of DM NS16550 device description UART clock can not be
got in runtime and by default it is set to 13MHz, if board PERIPH_CLK
is different, this should be specified in board configuration file.
For SPL builds HSUARTs are disabled and non-DM NS16550 driver is
compiled, if needed.
The change also updates default configs of devkit3250 and work_92105
boards to reflect updates in platform files.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
enable spi driver model for am437x_sk_evm as ti_qspi supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
enable spi driver model for dra74_evm as ti_qspi supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
enable mmc driver model for dra72_evm as ti_qspi supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This feature is required in SPL to enable support for loading from SPI
flash.
Also clean up the #define in socfpga_common.h.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin-Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This feature is required in SPL to enable support for loading from SPI
flash when the device is booted from QSPI.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Rather than using a new debug UART implementation, use the standard one
provided by U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Various updates did not make it through to this board. Also the instructions
for building a SPI image are no-longer correct. Fix these so that Jerry can
boot to a prompt again.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are some reports of stability issues at 672 MHz, see:
http://linux-sunxi.org/Orange_Pi_PC#DRAM_clock_speed_limit
So reduce the DRAM speed to 624MHz which seems to be reliable everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Undefine CONFIG_SPI_FLASH_USE_4K_SECTORS for UBI
and UBIFS support on serial NOR flash
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Undefine CONFIG_SPI_FLASH_USE_4K_SECTORS for UBI
and UBIFS support on serial NOR flash
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Undefine CONFIG_SPI_FLASH_USE_4K_SECTORS for UBI
and UBIFS support on serial NOR flash
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
These boards are similar enough to be supported in a single defconfig
file. Distinguish one from another by "DEVICE_TREE" from the command
line. The how-to-build in doc/README.uniphier should be also updated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These two are similar enough to be merged into a single
defconfig file. Distinguish one from another by "DEVICE_TREE"
from the command line. The how-to-build in doc/README.uniphier
should be also updated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The simple bus support must be enabled in SPL, otherwise the boards
will not be able to parse the DT and will fail to boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
This commit adds support of USB 1.1 storage media on AXS103 board.
For some yet unknown reason USB 2.0 doesn't work on AXS103 board issuing
messages like this:
------------------------>8-------------------
AXS# usb start
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80
unable to get device descriptor (error=-1)
1 USB Device(s) found
------------------------>8-------------------
As a work-around we're falling back to USB 1.1.
Indeed it is much slower but at least USB storage devices are usable on
AXS103.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Marsboard A10 haven't any PMIC at all, so add CONFIG_SUNXI_NO_PMIC=y to
Marsboard_A10_defconfig
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Olimex A20-SOM-EVB is an evaluation board for the Olimex
A20-SOM system-on-module. The baseboard provides a full-size SD
socket (connected to mmc3) in addition to the micro-SD socket on
the SOM itself (which is connected to mmc0).
Enable the mmc3 controller in the board defconfig.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Empire Electronix D709 tablet is a fairly standard 7" A13 tablet,
featuring usb-wifi, a micro-sd slot, micro-usb otg and headphone jack.
Empire Electronix is written on the back of the tablet, the D709 model
info can be found in the about tablet menu in android.
The PCB has no markings to speak of.
This dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
The uImage format is legacy for years now, enable support for the
fitImage format, which allows combining multiple files (kernel and
dtb) into a single file, offers better protection of the payload
and so on.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Update the ZYBO device tree and enable config options that relate to the
added devices in the device tree.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
LS1043ARDB Secure Boot Target from NOR has been added.
- Configs defined to enable esbc_validate.
- ESBC Address in header is made 64 bit.
- SMMU is re-configured in Bypass mode.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
kylin board use rk3036 SOC, 512M sdram, 8G emmc.
This add some basic files required to allow the board
to output serial message and can run command(mmc info etc).
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Switch to using tiny-printf for the firefly SPL, this reduces the SPL by
around 1800 bytes bringing it back under the 32k limit for both gcc 4.9
and gcc 5.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Add dts and defconfig for h8homletv2 board.
H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner.
It has UART, ethernet, USB, HDMI, etc ports on it.
A83T patches are tested on this board.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This commit adds support of USB 2.0 storage media on AXS10x boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Enable driver model MMC support on SoCFPGA.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The SR1500 board is a CycloneV based board, similar to the EBV
SoCrates, equipped with the following devices:
- SPI NOR
- eMMC
- Ethernet
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
These were added by mistake in commit fde7e189. They cause a warning when
configuring the boards. Remove them.
Fixes: fde7e18938 ("dm: tegra: pci: Move CONFIG_PCI_TEGRA to Kconfig")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reported-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Enable serial driver model for dra74_evm as ns16550 supports
driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that u-boot relocates the malloc area in SPL to SDRAM, with the
malloc area sitting below the SPL_STACK_R_ADDR the
SPL_STACK_R_MALLOC_SIMPLE_LEN needs to be set explicitly for
rockchip as its SPL_STACK_R_ADDR (512kb) is smaller then
STACK_R_MALLOC_SIMPLE_LEN (1Mb).
Using the same value as SYS_MALLOC_F_LEN (8kb) is enough to load u-boot
from SD card.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
This add some basic files required to allow the board to dispaly
serial message and can run command(mmc info etc)
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Moved board Kconfig fragment from previous patch into this one to fix
build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
Series-changes: 8
- moved board Kconfig fragment from previous patch into this one
Add SPL Kconfig for REGMAP and SYSCON, so REGMAP and SYSCON can
remove from SPL stage.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
We eventually need to drop the compatibility functions for driver model. As
a first step, create a configuration option to enable them and hide them
when the option is disabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have converted all x86 boards to use driver model timer,
remove these legacy timer codes in the tsc driver.
Note this also removes the TSC_CALIBRATION_BYPASS Kconfig option,
as it is not needed with driver model.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The board supports following features:
- Boot media support: SD card/e.MMC/SPI flash,
- Support LCD display (optional, disabled by default),
- Support ethernet,
- Support USB mass storage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[fix checkpatch warnings]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Use the U-Boot Driver Model. Just enable Freescale DSPI driver
and set DSPI related parameters in dts file.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043AQDS Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 DIMM
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two RGMII ports
* XFI 10G port
* SGMII
* QSGMII with 4x 1G ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
[York Sun: Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
Reuse dts files from ls1043a linux kernel. Some parts in dts files
may not be needed by U-Boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
This board was constantly parasiting on the CV SoCDK, so split it
into it's own separate directory. Moreover, the board config was
missing important bits, like simple-bus support in SPL, the DRAM
configuration was incorrect and the DTS was also missing the pre
reloc bits.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Jan Viktorin <viktorin@rehivetech.com>
This patch add ZyXEL NSA310S 1-Bay Media Server
The ZyXEL NSA310S device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1000Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 4 Status LED (green)
- 1 Copy/Sync button
- 1 Reset button
- 1 SATA II port
- 2 USB 2.0 ports (front and back)
- Smart fan
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
Enabling the new tiny-printf function makes the SPL image fit again in
the 8KiB restricted area.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
