Commit Graph

27949 Commits

Author SHA1 Message Date
Stefano Babic
a4f7d09831 pmic: fix missing SWITCH_SIZE
Applying ccbb18713b,
the define disappeared. Fix it.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2015-02-11 12:35:46 +01:00
Peng Fan
7428f55c94 pmic:pfuze implement pmic_mode_init
This patch is to implement pmic_mode_init function, and add prototype
in header file.

This function is to set switching mode for pmic buck regulators to
improve system efficiency.

Mode:
OFF: The regulator is switched off and the output voltage is discharged.
PFM: In this mode, the regulator is always in PFM mode, which
     is useful at light loads for optimized efficiency.
PWM: In this mode, the regulator is always in PWM mode operation
     regardless of load conditions.
APS: In this mode, the regulator moves automatically between
     pulse skipping mode and PWM mode depending on load conditions.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
2015-02-11 12:27:46 +01:00
Fabio Estevam
aee0013e53 mx53loco: Fix boot hang during reboot stress test
Currently by running the following test:

=> setenv bootcmd reset
=> save
=> reset

, we observe a hang after approximately 20-30 minutes of stress reboot test.

Investigation of this issue revealed that when a single DDR chip select is used,
the hang does not happen. It only happens when the two chip selects are active.

MX53 reference manual states at "28.6.2 Memory ZQ calibration sequence":

"The controller must keep the memory lines quiet (except for CK) for the ZQ
calibration time as defined in the Jedec (512 cycles for ZQCL after reset, 256
for other ZQCL and 64 for ZQCS)."

According to the SDE_0 and SDE_1 bit descriptions from register ESDCTL_ESDCTL:

"Writing 1 to SDE0 or SDE1 will initiate power up delays as JEDEC defines.
Power up delays are a function of the configured memory type (DDR2/DDR3/LPDDR2)"

So make sure to activate one chip select at time (CS0 first and then CS1 later),
so that the required JEDEC delay is respected for each chip select.

With this change applied the board has gone through three days of reboot stress
test without any hang.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2015-02-10 12:48:50 +01:00
Graeme Russ
2d6286ab79 arm: mxs: Add 'Wait for JTAG user' if booted in JTAG mode
When booting in JTAG mode, there is no way to use soft break-points, and
no way of knowing when SPL has finished executing (so the user can issue
a 'halt' command to load u-boot.bin for example)

Add a debug output and simple loop to stop execution at the completion of
the SPL initialisation as a pseudo break-point when booting in JTAG mode

Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
2015-02-10 12:48:50 +01:00
Graeme Russ
7a08603707 arm: mxs: Enable booting of mx28 without battery
Section 4.1.2 of Freescale Application Note AN4199 describes the
configuration required to operate the mx28 from a 5V source without a
battery.

This patch changes the behaviour of the dropout control of the DC-DC
converter (refer to section 11.12.9 of the mx28 Application Processor
Reference Manual - Document Number: MCIMX28RM, Rev 2, 08/2013) to the
following:
 - Always use 4P2 Linear Regulator if CONFIG_SYS_MXS_VDD5V_ONLY is defined
 - Switch between 4P2 Linear Regulator and Battery, using whichever has
   the highest voltage if CONFIG_SYS_MXS_VDD5V_ONLY isnot set (this is
   the same as the pre-patch behaviour)

Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Signed-off-by: Damien Gotfroi <dgotfroi@greenwatch.be>
2015-02-10 12:48:50 +01:00
Graeme Russ
950eaf6230 arm: mxs: Add debug outputs and comments to mxs SPL source files
It is difficult to track down fail to boot issues in the mxs SPL.
Implement the following to make it easier:
 - Add debug outputs to allow tracing of SPL progress in order to track
where failure to boot occurs. DEUBUG and CONFIG_SPL_SERIAL_SUPPORT must
be defined to enable debug output in SPL
 - Add TODO comments where it is not clear if the code is doing what it
is meant to be doing, even tough the board boots properly (these comments
refer to existing code, not to any code added by this patch)

Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
2015-02-10 12:48:49 +01:00
Ye.Li
e8cdeefc22 imx: mx6: Fixed AIPS3 base address issue
Should use AIPS3 configuration address 0x0227C000 to set AIPS3,
not the AIPS3 base address.
Additional, replace AIPS1_BASE_ADDR to AIPS3_ARB_BASE_ADDR to align with
AIPS1 and AIPS2, and resolve the AIPS3_ARB_BASE_ADDR undefine problem.

Signed-off-by: Ye.Li <B37916@freescale.com>
2015-02-10 12:48:49 +01:00
Ye.Li
9598f8c30c imx: imximage: Add QuadSPI boot support
Add QuadSPI boot support to imximage tool.

Note: The QuadSPI configuration parameters at offset 0x400 are not
included in this patch. Need other tools to generate the parameters
part.

Signed-off-by: Ye.Li <B37916@freescale.com>
2015-02-10 12:48:49 +01:00
Ye.Li
5f22d88f82 imx: mx6qsabreauto: Change to use common GPMI IO clock function
Since a clock function setup_gpmi_io_clk is implemented for GPMI
IO clock settings, change to use this common function in GPMI setup.

Signed-off-by: Ye.Li <B37916@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2015-02-10 12:48:49 +01:00
Peng Fan
ccbb18713b pmic:pfuz100 add switch mode and more registers
Add more pfuze register offset.
And switch mode definition.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-02-10 12:48:49 +01:00
Peng Fan
ee52f1a5fe pmic:pfuze add macro for setting voltage
"#define PFUZE100_SW1ABC_SETP(x) ((x - 3000) / 250)"
This macro is for configuring SW1A/B/C Output Voltage easily.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-02-10 12:48:48 +01:00
Peng Fan
1730af1bbd imx:mx6 update fuse_bank0_regs
Update fuse_bank0_regs structure according reference mannual.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-02-10 12:48:48 +01:00
Heiko Schocher
b4b39a7e54 arm, imx6, aristainetos: board updates
- use linux display timing settings
- change backlight duty cycle 500ns
- some defaultenvironment changes
- change fit_addr_r to 0x14000000 as needed if
  MAX_LOCKDEP_SUBCLASSES in linux gets increased.
- Environment now at 0xd0000 in nand flash

Signed-off-by: Heiko Schocher <hs@denx.de>
2015-01-29 18:37:49 +01:00
Nikita Kiryanov
f82eb2fa5d common: convert compulab splash load code to common code
Move board/compulab/common/splash.c code to
common/splash_source.c to make it available for everybody. This move
renames cl_splash_screen_prepare() to splash_source_load(), and
the compilation of this code is conditional on CONFIG_SPLASH_SOURCE.

splash_source features:
* Provide a standardized way for declaring board specific splash screen
  locations
* Provide existing routines for auto loading the splash image from the
  locations as declared by the board
* Introduce the "splashsource" environment variable, which makes it
  possible to select the splash image source.

cm-t35 and cm-fx6 are updated to use the modified version.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:44:08 +01:00
Nikita Kiryanov
3a236a3563 arm: mx6: cm-fx6: add splash screen support
Add support for splash screen.
The splash screen is loaded from the SPI flash and is displayed on the
HDMI display.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[grinberg@compulab.co.il: minor code and commit message updates]
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:42:30 +01:00
Nikita Kiryanov
7e8d7f2ac2 compulab: splash: support loading splash from sf
Add support for loading splash from sf.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[grinberg@compulab.co.il: staticize the sf global variable]
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:42:29 +01:00
Nikita Kiryanov
fd29dd554a compulab: splash: support multiple splash sources
Define a generic way for boards to define splash image locations:
- introduce struct splash_location
- introduce enum splash_storage
- update cl_splash_screen_prepare() to take an array of above struct
  and select the appropriate one based on the splashsource environment
  variable (if it is not defined- use the first splash location as default).

cm-t35 is updated to work with the new interface.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:42:29 +01:00
Nikita Kiryanov
7be4cd2cc5 compulab: splash: refactor splash.c
Move storage device specific code into its own function instead of
calling it directly from an otherwise storage device independent
function (cl_splash_screen_prepare).

This is a preparation for supporting multiple splash locations.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:42:29 +01:00
Nikita Kiryanov
6947e3f56f compulab: splash: use errno values
Use errno values to improve return reporting.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:42:29 +01:00
Nikita Kiryanov
1c2e529243 arm: mx6: cm-fx6: add support for usb keyboard
Add support for usb keyboard for cm_fx6.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:42:29 +01:00
Nikita Kiryanov
8015dde878 arm: mx6: cm-fx6: display compulab logo
Add compulab logo and display it on boot.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:42:29 +01:00
Nikita Kiryanov
deb94d6192 arm: mx6: cm-fx6: add hdmi console support
Add support for hdmi console.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:42:28 +01:00
Nikita Kiryanov
9fbdcf018e arm: mx6: cm-fx6: increase size of malloc area
Increase size of malloc area to make room for framebuffer
and other such big allocations.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:42:28 +01:00
Nikita Kiryanov
eab29802d6 arm: mx6: cm-fx6: pass 2nd nic mac addr to Linux
Obtain 2nd NIC MAC address from baseboard EEPROM and pass it to Linux.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:42:28 +01:00
Nikita Kiryanov
e7a2447ba2 compulab: eeprom: allow reading mac address from multiple eeproms
Implement the option to select the eeprom i2c bus when reading mac
address.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:42:28 +01:00
Nikita Kiryanov
cc67f4a63f arm: mx6: cm-fx6: change dtb node for ethaddr
When passing eth address to Linux via dtb, the "local-mac-address"
property should be set for "/soc/aips-bus@02100000/ethernet@02188000",
not "/fec".

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:42:27 +01:00
Nikita Kiryanov
508a6edea9 arm: mx6: cm-fx6: expand boot sequence
Expand boot sequence to the following order:
1) mmc boot: mmc boot script, then mmc bootm, then mmc bootz.
2) usb boot: usb boot script.
3) sata boot: sata boot script, sata bootm, sata bootz.
4) nand boot: nand bootm, then nand bootz.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-01-29 17:42:27 +01:00
Christian Gmeiner
8af9aff1e5 ot1200: add ot1200_spl_defconfig file
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>#
2015-01-22 11:03:19 +01:00
Christian Gmeiner
5324917126 ot1200: add basic SPL support
Currently we only support the Micron MT41K128M16JT-125 ddr3 chip.

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2015-01-22 11:03:19 +01:00
Christian Gmeiner
68a3664aec ot1200: add SPL configuration
We will only support loading u-boot.img from SPI flash stored
at the offset of 64k.

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2015-01-22 11:03:19 +01:00
Christian Gmeiner
e88b83575a ot1200: enable spi clock directly in ccgr_init(..)
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2015-01-22 11:03:19 +01:00
Christian Gmeiner
84c5dd16a4 ot1200: move ccgr and gpr init to c functions
We need this way for SPL boot.

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2015-01-22 11:03:19 +01:00
Christian Gmeiner
f77dd6d7db ot1200: make use of imx_ddr_size(..)
To support different ddr3 memory sizes we should start using
imx_ddr_size(..) instead of the define PHYS_SDRAM_SIZE.

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2015-01-22 11:03:18 +01:00
Christian Gmeiner
8551b3661c ot1200: select SUPPORT_SPL
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2015-01-22 11:03:18 +01:00
Stefano Babic
5ba49e75af mx6: fix warning in platinum board
Fix warning due to missing prototype for writel

Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2015-01-22 10:59:03 +01:00
Ye.Li
0da040bfd4 imx: mx6: Change ENV offset to 512K bytes for larger u-boot image
To align with other mx6 boards, change ENV offset from 384KB to
512KB position to fit a larger u-boot image.

Signed-off-by: Ye.Li <B37916@freescale.com>
2015-01-22 10:15:21 +01:00
Peng Fan
1565d54a76 imx:mx6sxsabresd board spl support
Add board level spl support for mx6sxsabresd board.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-01-22 09:56:06 +01:00
Peng Fan
f9e89ffd16 imx:mx6 add mx6sx in imx spl header file
Since mx6sx's memory space is different to mx6dq, redefine the SPL
related macro for mx6sx chip.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-01-22 09:55:47 +01:00
Peng Fan
d9efd47c03 imx:mx6sx add dram io configure for mx6sx
Define two structure mx6sx_iomux_ddr_regs and mx6sx_iomux_grp_regs.
Add a new function mx6sx_dram_iocfg to configure dram io.

Since mx6sx only have one channel mmdc0, define a new empty macro MMDC1
to replace mmdc1->entry=value for mx6sx. And to other mx6 soc, MMDC1
effects as "mmdc1->entry=value".

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-01-22 09:55:47 +01:00
Peng Fan
71abf19b0f imx:mx6sxsabresd spl support in header file
Add SPL support in mx6sxsabresd header file.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-01-22 09:55:47 +01:00
Peng Fan
3dae50d0a7 imx:mx6sxsabresd select SUPPORT_SPL
select SUPPORT_SPL for mx6sxsabresd.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-01-22 09:55:47 +01:00
Peng Fan
d1a2e91611 imx:mx6sxsabresd add spl config file
Add a SPL default configuration file for mx6sxsabresd board.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-01-22 09:55:47 +01:00
Alexandre Coffignal
ca6dc4f81c mxsboot : Support of 224-bytes OOB area length
Add support for the NAND Flash chip with page size of 4096+224-bytes OOB area length

For example Micron MT29F4G08 NAND flash device defines a OOB area which is
224 bytes long (oobsize).

Signed-off-by: Alexandre Coffignal <acoffignal@geral.com>
2015-01-19 09:10:52 +01:00
Stefan Roese
5d6050fdb8 arm: mx6: Add Barco platinum-picon and platinum-titanium
This patch adds the new Barco platinum platform. It currently
includes those two boards:

platinum-titanium
-----------------
This is the same board as the titanium that is already supported in
mainline U-Boot. But its now moved to this new platform to support
multiple "flavors" of imx6 boards in one directory. Its also moved
to support SPL booting. And with this we use the run-time DDR
configuration of this SPL support. The board is equipped with the
Micron MT41J128M16JT-125 DDR chips. We now can remove the DDR
related registers tuples from the imximage.cfg file. As all this
is done in the SPL at run-time.

platinum-picon
--------------
This board is new and based on the MX6DL with 1GiB DDR using the
Micron MT41K256M16HA DDR3 chips. Its also equipped with 2 NAND
chips (each 512MiB).

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Pieter Ronsijn <pieter.ronsijn@barco.com>
2015-01-19 09:07:31 +01:00
Fabio Estevam
834670eae0 mx6sxsabresd: Remove unneeded board_late_init()
Since commit 1f98e31bc0 ("imx: mx6sxsabresd: Use the pfuze common init
function") board_late_init() became empty, so we can safely remove this unneeded
function.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-01-19 09:04:42 +01:00
Otavio Salvador
99c618ff26 wandboard: Use 32bit color depth for Fusion LCD
The Fusion LCD needs the 32bit color depth to properly work; the
default is different on the 3.10.17 kernels and it is better to ensure
it work out of box using proper default color setting.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2015-01-19 09:02:47 +01:00
Tom Rini
ab77f24119 Merge branch 'master' of git://git.denx.de/u-boot-ti 2015-01-16 10:25:01 -05:00
Masahiro Yamada
d928664f41 powerpc: 74xx_7xx: remove 74xx_7xx cpu support
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2

Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
2015-01-16 10:24:39 -05:00
Masahiro Yamada
eb8b3f1edd mpc8xx: remove unused linker script
Now TQM8xx is the only remaining board family of mpc8xx.
It uses its own linker script, board/tqc/tqm8xx/u-boot.lds.

arch/powerpc/cpu/mpc8xx/u-boot.lds is not used by any boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
2015-01-16 10:24:38 -05:00
Masahiro Yamada
9c3c5c8b02 ppc4xx: remove dead code
Since commit 843125daeb (ppc4xx: remove HH405 board), CONFIG_HH405
is not defined.

Since commit d526330479 (ppc4xx: remove PMC405), CONFIG_PMC405
is not defined.

Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
2015-01-16 10:24:14 -05:00