The patch adds SPL for the arm1136 architecture and
inserts SPL (the produced binary) to clobber target
in the main Makefile.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch modifies start.S for the arm1136 to make it
conform to start.S in armv7 architecture, to make it
usable if the SPL framework is used.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Patch fix warnings compiling with ELDK-4.2:
clock.c: In function 'get_standard_pll_sel_clk':
clock.c:341: warning: 'freq' may be used uninitialized in this function
Reported-by : Marek Vasut <marex@denx.de>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add the software workaround for ARM erratum ID 468414.
According to mx53/mx51 errata document:
"ENGcm11133 - ARM: NEON load data can be incorrectly forwarded to a
subsequent request
Description:
Under very specific set of conditions, data from a Neon load request can be incorrectly forwarded
to a subsequent, unrelated memory request.
The conditions are as follows:
• Neon loads and stores must be in use
• Neon L1 caching must be disabled
• Trustzone must be configured and in use
• The secure memory address space and the non-secure memory address space both use the same
physical addresses, either as an alias or the same memory location or for separate memory
locations
The issue is reported by ARM, erratum ID 468414, Category 2"
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently PLL2 is not explicitely configured for mx53 and it runs at 333MHz.
Since PLL2 is the parent clock for DDR2, IPU, VPU, we should set it at 400MHz
instead.
Without doing so, it is not possible to use a 2.6.35 FSL kernel and display HDMI
at 1080p because the IPU clock cannot reach the requested frequency.
Set PLL2 to 400MHz, so that 1080p can be played and the DDR2 can run at its
maximum frequency.
Also, setup the other PLL's as done in FSL U-boot and re-arrange the code a little
bit to allow easier comparison with the original clock setup from FSL U-boot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
init_clock is currently shared between mx51 and mx53 and it contains lots of
ifdef's which makes it really hard to follow the code.
Split the init_clock between mx51 and mx53 to allow easier readability.
No functional changes are made.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The kernel from Freescale expects that the bootloader passes the board revision.
Read the board revision and pass it via get_board_rev().
Without passing the board revision the kernel does not operate properly as the
initialization of peripherals are different in revA versus revB boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Each eSDHC instance has a dedicated clock.
gd->sdhc_clk must also be set accordingly. This is good for the case only a
single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A
future patch will fix the multi-instance use case (initialization made directly
with fsl_esdhc_initialize()).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Clean up mx35 lowlevel_init:
- Indent with tabs.
- Fix comments.
- Use defined values instead of literal constants.
- Use defined macros instead of duplicating code.
- Use macro parameters with default values instead of #define'd configs.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Clean up mx25 lowlevel_init:
- Add comments.
- Do not use write32 repeatedly with the same value in order not to increase
code size.
- Make register values configurable.
- Use macro parameters with default values instead of literal constants.
- Use defined macros instead of duplicating code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Matthias Weisser <weisserm@arcor.de>
The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0
register is actually composed of two bit-fields: one pre-divider and one
post-divider. This patch fixes the CCM access macros and the code using them
accordingly.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Optimize mx5 lowlevel_init.S code size:
- Compute values at compile time rather than at runtime where possible.
- Assign r4 to hold the zero value rather than setting registers to 0 again and
again.
- Associate a function to setup_pll rather than expanding its large macro code
multiple times.
- Allocate constant values in section only if used.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
The MMC driver appropriate for the i.MX25 is fsl_esdhc, which has nothing to do
with mxcmmc.
Also, each eSDHC instance has a dedicated clock, so gd->sdhc_clk must be set
accordingly. This is good for the case only a single SDHC instance is used
(initialization made with fsl_esdhc_mmc_init()). A future patch will fix the
multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
The FEC is the only SoC Ethernet support available on i.MX25, so define
cpu_eth_init() only for it instead of returning a misleading success code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Use the standard mxc_get_clock() instead of exporting internal functions and
using literal constant values.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
mxc_get_clock(MXC_FEC_CLK) should return the IPG clock, not the AHB clock.
Also, imx_get_fecclk() was correct but reimplemented the calculation of the IPG
clock, so remove the duplicated code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Avoid possible overflow in clock calculations, and do not waste calls to lldiv()
to divide simple ulongs.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The MFN bit-field of the PLL registers represents a signed value. See the
reference manual.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The i.MX5 eSDHC clocks were considered as coming from the IPG clock although
they have dedicated clock paths.
Also, on i.MX5/6, each SDHC instance has a dedicated clock, so gd->sdhc_clk must
be set accordingly. This is good for the case only a single SDHC instance is
used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix
the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
There are only 2 I²C instances on i.MX51, but 3 on i.MX53.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The FEC clock does not come from PLL1, but from the IPG clock. The previous code
was even inconsistent with itself, returning the IPG clock as expected for
imx_get_fecclk(), but the PLL1 clock for mxc_get_clock(MXC_FEC_CLK).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The code handling the dividers was duplicated for each possible input clock, and
this function can benefit from the newly introduced get_standard_pll_sel_clk()
function instead of duplicating this mux handling code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
This function returned 66500000 instead of the correct lp_apm clock frequency if
the CCM.CSCMR1.uart_clk_sel mux is set to 3.
This patch fixes this issue by introducing the get_standard_pll_sel_clk()
function that will be used by future patches to handle identical muxes used by
many other clocks.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
This fixes the "IPG PERCLK" frequency printed by the clocks command. The issue
was that get_ipg_per_clk() used periph_clk instead of lp_apm in the case
CCM.CBCMR.perclk_lp_apm_sel is set.
It also fixes I²C support.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
In the case periph_clk comes from periph_apm_clk, the latter is selected by the
CCM.CBCMR.periph_apm_sel mux, which can source the lp_apm clock from its
input ♯2. get_periph_clk() returned 0 instead of the lp_apm clock frequency in
this case.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
If CCM.CCSR.lp_apm is set, the lp_apm clock is not necessarily 32768 Hz x 1024.
In that case:
- on i.MX51, this clock comes from the output of the FPM,
- on i.MX53, this clock comes from the output of PLL4.
This patch fixes the code accordingly.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
This fixes config_pll_clk(), which used 0x20 instead of 0x200 for PLL4_CLOCK.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The i.MX51 has a single USB PHY clock, while the i.MX53 has two. These 3 clocks
have different clock gate control bit-fields.
The existing code was correct only for i.MX53, so this patch fixes the i.MX51
use case.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Jana Rapava <fermata7@gmail.com>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
The clock gate values are 2-bit bit-fields. Hence, setting or clearing only one
of these bits like what was done is wrong and can lead to unpredictable behavior
depending on the original value of these bit-fields.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Use clock gate definitions having names showing clearly the gated clock instead
of names giving only a register field index.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Clean up the i.MX5 clock driver:
- Use readl() and writel() instead of their __raw_ counterparts.
- Use the clr/setbits_le32() family of macros rather than expanding code.
- Use accessor macros for bit-fields instead of _MASK and _OFFSET.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of
duplicated definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using
MXC_I2C_CLK on all imx systems using i2c.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Acked-by: Stefano Babic <sbabic@denx.de>
tested on a MCIMX257CJM4A which now reports :
CPU: Freescale i.MX25 rev1.2 at 399 MHz
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Register CCM_CHSCCDR (offset 0x34 in CCM) is named CCM_CHSCCDR in
reference manual, but was named chscdr in struct mxc_ccm_reg.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
