SAR1_CPU_CORE_MASK was wrong, probably copy/paste
from another architecture.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support. Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM. If this needs to be done, it should be
handled in the board file, not in core code.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch introduces the SDRAM scrubbing for ECC enabled board
to fill/initialize the ECC bytes. This is done via the XOR engine
to speed up the process. The scrubbing is a 2-stage process:
1) SPL scrubs the area 0 - 0x100.0000 (16MiB) for the main U-Boot
2) U-Boot scrubs the remaining SDRAM area(s)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This is tested on the DB-MV784MP-GP eval board. To really enable ECC
support on this board the I2C EEPROM needs to get changed. As it
saves the enabling of ECC support internally. For this the following
commands can be used to enable ECC support on this board:
Its recommended for first save (print) the value(s) in this EEPROM
address:
=> i2c md 4e 0.1 2
0000: 05 00 ..
To enable ECC support you need to set bit 1 in the 2nd byte:
Marvell>> i2c mw 4e 1.1 02
Marvell>> i2c md 4e 0.1 2
0000: 05 02 ..
To disable ECC support again, please use this command:
Marvell>> i2c mw 4e 1.1 00
Marvell>> i2c md 4e 0.1 2
0000: 05 00 ..
On other AXP boards, simply plugging an ECC DIMM should be enough to
enable ECC support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds the DDR3 setup and training code taken from the Marvell
U-Boot repository. This code used to be included as a binary (bin_hdr)
into the Armada A38x boot image. Not linked with the main U-Boot. With this
code addition and the serdes/PHY setup code, the Armada A38x support
in mainline U-Boot is finally self-contained. So the complete image
for booting can be built from mainline U-Boot. Without any additional
external inclusion.
Note:
This code has undergone many hours (days!) of coding-style cleanup and
refactoring. It still is not checkpatch clean though, I'm afraid. As the
factoring of the code has so many levels of indentation that many lines
are longer than 80 chars.
Signed-off-by: Stefan Roese <sr@denx.de>
With the upcoming addition of the Armada 38x DDR support, which is not
compatible to the Armada XP DDR init code, we need to introduce a new
directory infrastructure. To support multiple Marvell DDR controller.
This will be the new structure:
drivers/ddr/marvell/axp
Supporting Armada XP (AXP) devices (and perhaps Armada 370)
drivers/ddr/marvell/a38x
Supporting Armada 38x devices (and perhaps Armada 39x)
Signed-off-by: Stefan Roese <sr@denx.de>
