onenand_probe() function is missing to set mtd->type. So set same type as
which sets onenand Linux kernel driver.
After this change 'mtd list' prints correct type instead of 'Unknown'.
Signed-off-by: Pali Rohár <pali@kernel.org>
- Armada 8k: Add NAND support via PXA3xx NAND driver (Baruch)
- Armada 8k: Use ATF serdes init instead of the "old" U-Boot version
(Baruch)
- Minor update to Octeon TX/TX2 defconfig (Stefan)
Based on Linux kernel commit fc256f5789cb ("mtd: nand: pxa3xx: enable
NAND controller if the SoC needs it"). This commit adds support for the
Armada 8040 nand controller.
The kernel commit says this:
Marvell recent SoCs like A7k/A8k do not boot with NAND flash
controller activated by default. Enabling the controller is a matter
of writing in a system controller register that may also be used for
other NAND related choices.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shmuel Hazan <shmuel.h@siklu.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
The kfree() call is unreachable, and is not needed. Remove this call and
the fail_disable_clk label.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Use the generic DT code to find the device compatible property for us.
This makes the driver look more like other current drivers. It also make
it easier to add support for other variants like Armada 8K in a future
commit.
Signed-off-by: Shmuel Hazan <shmuel.h@siklu.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Use tabs to be aligned with the rest of the code.
Fixes: 658df8bd94 ("mtd: spi-nor-core: Add octal mode support")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Adds support for NAND controllers found on OcteonTX or
OcteonTX2 SoC platforms. Also includes driver to support
Hardware ECC using BCH HW engine found on these platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The cfi-flash driver uses an open-coded version of the generic
algorithm to decode and translate multiple frames of a "reg" property.
This starts off the wrong foot by using the address-cells and size-cells
properties of *this* very node, and not of the parent. This somewhat
happened to work back when we were using a wrong default size of 2,
but broke about a year ago with commit 0ba41ce1b7 ("libfdt: return
correct value if #size-cells property is not present").
Instead of fixing the reinvented wheel, just use the generic function
that does all of this properly.
This fixes U-Boot on QEMU (-arm64), which was crashing due to decoding
a wrong flash base address:
DRAM: 1 GiB
Flash: "Synchronous Abort" handler, esr 0x96000044
elr: 00000000000211dc lr : 00000000000211b0 (reloc)
elr: 000000007ff5e1dc lr : 000000007ff5e1b0
x0 : 00000000000000f0 x1 : 000000007ff5e1d8
x2 : 000000007edfbc48 x3 : 0000000000000000
x4 : 0000000000000000 x5 : 00000000000000f0
x6 : 000000007edfbc2c x7 : 0000000000000000
x8 : 000000007ffd8d70 x9 : 000000000000000c
x10: 0400000000000003 x11: 0000000000000055
^^^^^^^^^^^^^^^^
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefan Roese <sr@denx.de>
When possible use DMA for reading from CFI flash, this provides upto 5x
improvement in read performance with high speed CFI compliant flashes
like HyperFlash.
Code will gracefully fallback to CPU copy when DMA is unavailable.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This member was presumably dropped when this driver was converted from
Linux. However, it is still used in log statements during initialization.
This patch adds the member back. In addition, allocation of struct
vf610_nfc has been moved to the callers of vf610_nfc_nand_init. This allows
it to be allocated by DM (if it is being used) and for dev to be
initialized.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
There are too many levels of indirection when calling dev_err. This is an
artifact of the conversion of brcmnand_host.pdev from a struct
platform_device (which has a member `dev` pointing to a struct device) to
struct udevice.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Use mtd_info to get a device to log with.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Get it from spinand->slave->dev. Another option would be to use
spinand_to_mtd(spinand)->dev, but this is what the existing code uses.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This fixes dev_xxx() not always being called with a device. In
spi_nor_reg_read, a the slave device may not always be available, so we use
bus and cs instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This header is needed so struct udevice can be used in dev_xxx().
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Usually the device is gotten from sunxi_nfc. This is a struct device and
not a struct udevice, but the whole driver seems to be written wihout DM
anyway...
In a few instances, this patch modifies functions to take an nfc to log
with. In once instance we use mtd_info's device since there is no nfc.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Use the device from any mtd already available, or from the active mtd via
pxa3xx_nand_info if one is not.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Fix a typo
%s/interract/interact/
Use Samsung's capitalization of their trademarks
%s/onenand/OneNAND/
%s/Hyperflash/HyperFlash/
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Add other Hyperflash cases as noted by Stefan]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some of Marvell A3700 boards use mx25u12835f, specifically uDPU
and ESPRESSObin v7.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
[a.heider: adapt commit message to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
NAND_ARASAN selecting DM_MTD uunconditionally. Driver can be enabled with
!DM that's why Kconfig it showing it as error:
WARNING: unmet direct dependencies detected for DM_MTD
Depends on [n]: DM [=n]
Selected by [y]:
- NAND_ARASAN [=y] && MTD_RAW_NAND [=y]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The most of drivers are using '_' instead of '-' in driver name. That's why
sync up these names to be aligned. It looks quite bad to see both in use.
It is visible via dm tree command.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Nand writes should skip the bad blocks with "nand write" command.
In case of bad blocks with above 32-bit address, nand_block_isbad()
returns false due to truncated bad block address.
In below code segment,
if (nand_block_isbad(mtd, offset & ~(mtd->erasesize - 1)))
offset is 64-bit and mtd->erasesize is 32-bit, hence the truncation is
happening. Cast 'mtd->erasesize' with loff_t to fix this issue.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
FMC2 EBI support has been added. Common resources (registers base
address and clock) can now be shared between the 2 drivers using
"st,stm32mp1-fmc2-nfc" compatible string. It means that the
common resources should now be found in the parent device when EBI
node is available.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch renames functions and local variables.
This cleanup is done to get all functions starting by stm32_fmc2_nfc
in the FMC2 raw NAND driver when all functions will start by
stm32_fmc2_ebi in the FMC2 EBI driver.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
FMC2_TIMEOUT_5S will be used each time that we need to wait.
It was seen, during stress tests in an overloaded system,
that we could be close to 1 second, even if we never met this
value. To be safe, FMC2_TIMEOUT_MS is set to 5 seconds.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove inline comments that are useless since function label are
self explanatory.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The chip select defined in the device tree could only be 0 or 1.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
In the unlikely event that both blocks 10 and 11 are marked as bad (on a
32 bit machine), then the process of marking block 10 as bad stomps on
cached entry for block 11. There are (of course) other examples.
Signed-off-by: Patrick Doyle <pdoyle@irobot.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
The -ENODEV error value in spi_nor_read_id() is incorrect since there
clearly is a device - it just cannot be supported. Use -ENOMEDIUM instead
which has the virtue of being less common.
Fix the return value in spi_nor_scan().
Also there are a few printf() statements which should be debug() since
they bloat the code with unused strings at present. Fix those while here.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases SPL needs to be able to erase but TPL just needs to read.
Allow these to have separate settings for SPI_FLASH_TINY.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add device table for new Micron SPI NAND devices, which have multiple
dies.
Also, enable support to select the dies.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add SPINAND_HAS_CR_FEAT_BIT flag to identify the SPI NAND device with
the Continuous Read mode.
Some of the Micron SPI NAND devices have the "Continuous Read" feature
enabled by default, which does not fit the subsystem needs.
In this mode, the READ CACHE command doesn't require the starting column
address. The device always output the data starting from the first
column of the cache register, and once the end of the cache register
reached, the data output continues through the next page. With the
continuous read mode, it is possible to read out the entire block using
a single READ command, and once the end of the block reached, the output
pins become High-Z state. However, during this mode the read command
doesn't output the OOB area.
Hence, we disable the feature at probe time.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add device table for M79A and M78A series Micron SPI NAND devices.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add the SPI NAND device MT29F2G01ABAGD series number, size and voltage
details as a comment.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
In order to add new Micron SPI NAND devices, we generalized the OOB
layout structure and function names.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The types of "offset" and "size" of "struct mtd_partition" are uint64_t,
while mtd_parse_partitions() uses int to work with these values. When
the offset reaches 2GB, it is interpreted as a negative value, which
leads to error messages like
mtd: partition "<partition name>" is out of reach -- disabled
eg. when using the "ubi part" command.
Fix this by using uint64_t for cur_off and cur_sz.
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fixed delay 200us is not working in certain platforms. Change to
poll for reset completion status to have more reliable reset process.
Controller will set the rst_comp bit in intr_status register after
controller has completed its reset and initialization process.
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Radu Bacrau <radu.bacrau@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Always put the controller in reset, then take it out of reset.
This is to make sure controller always in reset state in both SPL and
proper Uboot.
This is preparation for the next patch to poll for reset completion
(rst_comp) bit after reset.
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Radu Bacrau <radu.bacrau@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently when using OF_PLATDATA the binding between devices and drivers
is done trying to match the compatible string in the node with a driver
name. However, usually a single driver supports multiple compatible strings
which causes that only devices which its compatible string matches a
driver name get bound.
To overcome this issue, this patch adds the U_BOOT_DRIVER_ALIAS macro,
which generates no code at all, but allows an easy way to declare driver
name aliases. Thanks to this, dtoc could be improve to look for the driver
name based on its alias when it populates the U_BOOT_DEVICE entry.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using OF_PLATDATA, the bind process between devices and drivers
is performed trying to match compatible string with driver names.
However driver names are not strictly defined, and also there are different
names used when declaring a driver with U_BOOT_DRIVER, the name of the
symbol used in the linker list and the used in the struct driver_info.
In order to make things a bit more clear, rename the drivers names. This
will also help for further OF_PLATDATA improvements, such as checking
for valid driver names.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fix for sandbox of-platdata to avoid using an invalid ANSI colour:
Signed-off-by: Simon Glass <sjg@chromium.org>
Compiling drivers/mtd/spi/sandbox.c fails when compiled with
CONFIG_LOG=n:
In file included from include/common.h:20,
from drivers/mtd/spi/sandbox.c:13:
drivers/mtd/spi/sandbox.c:295:15: error: format ‘%s’ expects argument of
type ‘char *’, but argument 7 has type ‘int’ [-Werror=format=]
295 | log_content(" cmd: transition to %s state\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
37 | #define pr_fmt(fmt) fmt
| ^~~
include/log.h:128:30: note: in expansion of macro ‘log_nop’
128 | #define log_content(_fmt...) log_nop(LOG_CATEGORY, \
| ^~~~~~~
drivers/mtd/spi/sandbox.c:295:3: note: in expansion of macro
‘log_content’
295 | log_content(" cmd: transition to %s state\n",
| ^~~~~~~~~~~
drivers/mtd/spi/sandbox.c:295:37: note: format string is defined here
295 | log_content(" cmd: transition to %s state\n",
| ~^
| |
| char *
| %d
Supply function sandbox_sf_state_name() independent of CONFIG_LOG.
Fixes: c3aed5db59 ("sandbox: spi: Add more logging")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
