The new zlib code wants asm/unaligned.h, so have the Blackfin version pull
in the asm-generic/unaligned.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is based on the asm-arm/unaligned.h, but made generic so all arches
that cannot do unaligned accesses can utilize it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If a splashscreen is used the console scrolling used the
scroll size as needed when a logo was displayed. This
patch sets the scroll size to the whole screen if
a splashscreen is shown.
Signed-off-by: Matthias Weisser <matthias.weisser@graf-syteco.de>
Building examples/standalone/eepro100_eeprom triggers this error:
In file included from include/common.h:629,
from eepro100_eeprom.c:24:
include/net.h: In function 'NetReadIP':
include/net.h:430: warning: implicit declaration of function 'memcpy'
eepro100_eeprom.c: At top level:
eepro100_eeprom.c:81: error: conflicting types for 'memcpy'
include/net.h:430: error: previous implicit declaration of 'memcpy' was here
Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This code has compile problems and the company does not even exist any
more. So we take the liberty to drop support for it.
Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Wolfgang Denk <wd@denx.de>
CC: Ben Warren <biggerbadderben@gmail.com>
The 36-bit build exceeds the 512k size we have. Removing FIT type image
support allows us to fit and we dont really use it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The length of configured MTDPARTS_DEFAULT string
could be greater than console printbuffer size.
Replace printf() by puts() to avoid potential buffer
overflows.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch corrects small mistake in the register list in
doc/README.mpc8536ds. These registers are 32 bits and this one starts
at ....c not ....e
When using the ...c address I can boot from sd, when using the ...e
address I cannot.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Acked-by: Hu Mingkai <B21284@freescale.com>
Also enable support for CONFIG_HWCONFIG because we use this for
configuring if this hardware has a FEC or not.
syntax:
hwconfig=fec:on if hardware has an fec
hwconfig=fec:off if hardware has no fec
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Also use hwconfig to configure whether the board has a FEC or not.
We then can adjust the DTS to tell Linux if there is a FEC present.
syntax:
hwconfig=fec:on if hardware has a FEC
hwconfig=fec:off if hardware has no FEC
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
The auto-update feature (CONFIG_UPDATE_TFTP) requires that the env
variable serverip be set for the TFTP access. If DHCP is to be used
to get the serverip env variable, this doesn't work as DHCP happens
after the auto-update attempt has run. A solution is to run DHCP in
PREBOOT, but even this is too late.
To solve this, we move update_tftp() below the PREBOOT stuff.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Some people boot images with the entry point in the middle of the blob
(like Linux with the head code in discardable .init.text), and there is no
no real requirement that the entry point be right after the mkimage header
when doing XIP, so let people specify whatever they want. If they do need
an entry right after the header, then they still can do that with normal
-e behavior.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch uses gd->relocaddr variable to store uboot's relocated
address in RAM and shows it in bdinfo command.
This patch moves CONFIG_AMIGAONEG3SE style copying of the address
in board_init_f to just before relocation is actually done.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Tested-by: Detlev Zundel <dzu@denx.de>
There is be a path through mmc_read in drivers/mmc/mmc.c where
malloc'd memory is not freed before exiting mmc_read: it occurs if
mmc_set_blocklen() returns a non-zero value.
Reported-by: Quentin Armitage <Quentin@Armitage.org.uk>
Signed-off-by: Wolfgang Denk <wd@denx.de>
* convert otc570 board to use c stucture SoC access
* change gpio access to at91_gpio syntax
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
The patch removes warnings at compile time and provides
some cleanup code:
- Removed comment on NAND (not yet supported) from lowlevel_init.S
- Removed NFMS bit definition from imx-regs.h
The bit is only related to MX.25/35 and can lead to confusion
- Moved is_soc_rev() to soc specific code (removed from mx51evk.c)
Signed-off-by: Stefano Babic <sbabic@denx.de>
Supporting new machine ids for SoCs spear310 and spear320
include/asm-arm/mach-types.h has to be updated before applying
this patch for build to work
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Add support for the ARM part of the mgcoge2, named suen3.
This board is based on the Marvell Kirkwood (88F6281) SoC.
As there come more board variants, common config options
are collected in include/configs/km_arm.h. Also, this board
use common code for all keymile boards, which is stored in
board/keymile/common/common.c
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Heiko Schocher <hs@denx.de>
This is an i.MX25 base board with only NAND
so it uses nand_spl to boot.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Tune configuration, add support for (redundant) environment in NAND.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>
general cleanup
move clock init to cpu_eth_init in cpu/arm926ejs/mx27/generic.c
make MX27 specific phy init conditional on CONFIG_MX27
replace call to imx_get_ahbclk with one to imx_get_fecclk
and define imx_get_fecclk in include/asm-arm/arch-mx27/clock.h
Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>
ARM926EJS core with MX31 peripherals.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Earlier Version Signed-off-by: Wolfgang Denk <wd@denx.de>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>
remove ifdef'd clock selection code from
serial_mxc.c and replace with call to imx_get_uartclk
Add definitions for imx_get_uartclk to imx31 and imx27
include files.
This makes it easier to add new imx platforms.
Signed-off-by: John Rigby <jcrigby@gmail.com>
The patch adds initial support for the Freescale mx51evk board.
Network (FEC) and SD controller (fsl_esdhc) are supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
The esdhc controller in the mx51 processor is quite
the same as the one in some powerpc processors
(MPC83xx, MPC85xx). This patches adapts the driver
to support the arm mx51.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Some Freescale's processors of different architecture
have the same peripheral (eSDHC controller in PowerPC
and i.MX51). This patch adds accessors for
the internal registers of the SOCs, as already
implemented in the PowerPC architecture.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Most controllers can check if there is a card in the slot.
However, they require pins that could be not available because
required by other functions and the detection of a card must
be performed in another way. This patch adds a weak function
that a board can implement to add its internal custom way
to check the presence of a MMC/SD card.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Most cards do not answer if some reserved bits
in the ocr are set. However, some controllers
can set bit 7 (reserved for low voltages), but
how to manage low voltages SD card is not yet
specified.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The patch add header files to support the pin multiplexer
of the the Freescale i.MX51 processor.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
The patch add header files to support the Freescale i.MX51
processor, setting definitions for internal registers.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
The patch add initial support for the Freescale i.MX51 processor
(family arm cortex_a8).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
edb93xx: Fix SDRAM initialization by issuing a precharge all command before
forcing the precharge and select mode register update mode before programming
the mode registers. Write to the SDRAM banks in order to force a precharge,
reading causes the edb93xx boards to hang
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
ep93xx: Refactoring of the timer code, including the following changes
* use a free running timer instead of a periodical one
* use unsigned long long for total number of ticks
* hold the timer state in a structure instead of separate variables
* increment the timer counter instead of decrementing it
* remove unused function udelay_masked()
* remove unused function set_timer()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
ep93xx: Use unsigned long long for calculation of sys ticks in clk_to_systicks()
for proper handling of large intermediate values
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
725233: PLD instructions executed with PLD data forwarding
enabled can result in a processor deadlock
This deadlock can happen when NEON load instructions are used together
with cache preload instructions (PLD). The problematic conditions
can be triggered in-the-wild by NEON optimized functions from pixman
library (http://cgit.freedesktop.org/pixman), which perform dynamic
adjustment of prefetch distance.
The workaround disables PLD data forwarding by setting PLD_FWD bit
in L2 Cache Auxiliary Control Register as recommended in ARM Cortex-A8
errata list.
The deadlock can only happen on r1pX revisions of Cortex-A8 (used in
OMAP34xx/OMAP35xx). Performance impact of the workaround is practically
non-existant.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Configuration defines should be preceeded with CONFIG_SYS_. Renamed
some at91 specific defines to conform to this naming convention:
AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME
AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCK
Signed-off-by: Achim Ehrlich <aehrlich@taskit.de>
linking eeprom with libgeneric.a is not really needed and causes following
error:
../../lib_generic/libgeneric.a(string.o): In function `strcmp':
/home/ladis/src/u-boot-ti/lib_generic/string.c:152: multiple definition of `strcmp'
../../examples/standalone/libstubs.a(stubs.o):include/_exports.h:24: first defined here
make[1]: *** [eeprom.srec] Error 1
Fix undefined reference to memset generated by some versions of gcc
to zero out initialized structure on the stack:
eeprom.o: In function `eeprom':
board/voiceblue/eeprom.c:152: undefined reference to `memset'
make[1]: *** [eeprom] Error 1
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Reindent configuration header to limit line lenght to 80 characters by
removing obvious and sometimes misleading comments.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Limit line length to 80 characters mostly by removing obvious and sometimes
misleading comments. Fix indentation, too.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
