Commit Graph

10493 Commits

Author SHA1 Message Date
Fabian Vogt
7670909638 ARM: bcm283x: use OF_CONTROL for bcm283x
This patch removes use of U_BOOT_DEVICE in board/raspberrypi/rpi/rpi.c,
enables OF_CONTROL in the config and adjusts the rpi_*defconfig configs.

Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-11-28 20:15:18 -05:00
Fabian Vogt
ff5d7ae713 fdt: adjust bcm283x device tree for u-boot
The information currently set via platdata has to be represented in the
device tree now. bcm283x-uboot.dtsi adds the u-boot specific "skip-init"
property to the serial nodes and enables initialization in the pre-reloc phase.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-11-28 20:09:50 -05:00
Fabian Vogt
460255842c fdt: import bcm283x device tree sources from the linux kernel tree
This patch adds device trees for the bcm283x platform to be used with
OF_CONTROL. The version 4.8-rc7 of the linux kernel was used as source.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-11-28 20:09:49 -05:00
Andrew F. Davis
ac34286647 keystone2: Move target selection to Kconfig
The config option TARGET_K2x_EVM is set by the k2x defconfigs to pick
a board target, but the header configs also set K2x_EVM. This config
is redundant, remove it and use TARGET_K2x_EVM everywhere in its place.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-11-28 15:10:34 -05:00
FUKAUMI Naoki
5782954c2b sunxi: add support for Nintendo NES Classic Edition
Add board support for sun8i_r16 Nintendo NES Classic edition.

Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
[jagan: Add commit message body]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-28 15:10:30 -05:00
Yann E. MORIN
2997ee5054 arm: sunxi: do not force USB for arch-sunxi
Currently, USB is forced-enabled for the sunxi familly, and there is no
way to disable it.

However, USB takes a long time to initiliase, delaying the boot by up to
5 seconds (without any USB device attached!). This is a very long delay,
especially in cases where USB booting is not wanted at all, and where
the device is expected to boot relatively often (even in production).

Change the way the dependencies are handled, by only forcibly selecting
USB when CONFIG_DISTRO_DEFAULTS ("defaults suitable for booting general
purpose Linux distributions") is set. This option defaults to y for the
sunxi familly, so the current default behaviour is kept unchanged. Users
interested in boot time and/or size will be able to disable this to
further disable USB.

With USB disabled, the time spent in U-Boot before handing control to
the Linux kernel is about 1s now, down from ~5s (Nanopi Neo, sunxi H3).

Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-11-28 15:10:28 -05:00
Alexander Graf
95b62b2e28 efi_loader: Allow to compile helloworld.efi w/o bundling it
Today we can compile a self-contained hello world efi test binary that
allows us to quickly verify whether the EFI loader framwork works.

We can use that binary outside of the self-contained test case though,
by providing it to a to-be-tested system via tftp.

This patch separates compilation of the helloworld.efi file from
including it in the u-boot binary for "bootefi hello". It also modifies
the efi_loader test case to enable travis to pick up the compiled file.
Because we're now no longer bloating the resulting u-boot binary, we
can enable compilation always, giving us good travis test coverage.

Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-27 09:53:39 -05:00
Tom Rini
8d0898544e Merge git://git.denx.de/u-boot-rockchip 2016-11-26 09:26:27 -05:00
Simon Glass
c420ef67e5 rockchip: Add support for veyron-minnie (ASUS Chromebook Flip)
This adds support for the Asus Chromebook Flip, an RK3288-based clamshell
device which can flip into 'tablet' mode. The device tree file comes from
Linux v4.8. The SDRAM parameters are for 4GB Samsung LPDDR3.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:32 -07:00
Simon Glass
e70408c069 rockchip: Add support for veyron-mickey (Chromebit)
This adds support for the Asus Chromebit, and RK3288-based device designed
to plug directly into an HDMI monitor. The device tree file comes from
Linux v4.8.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:32 -07:00
Simon Glass
20b13e8d7e rockchip: veyron: Adjust ARM clock after relocation
Update board_init() to increase the ARM clock to the maximum speed on
veyron boards. This makes quite a large difference in performance. With
this change, speed goes from about 750 DMIPS to 2720 DMIPs.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:31 -07:00
Simon Glass
aede3acc9c rockchip: Move jerry SDRAM settings into its own .dts file
The SDRAM settings are not common across all veyron models. Move the
current settings into Jerry's file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:31 -07:00
Simon Glass
5e9b15034b rockchip: Rename jerry files to veyron
At present we have a single rk3288-based Chromebook: chromebook_jerry. But
all such Chromebooks can use the same binary with only device-tree
differences. The family name is 'veyron', so rename the files accordingly.

Also update the device-tree filename since this currently differs from
Linux.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:31 -07:00
Simon Glass
987a404aa1 rockchip: video: Check for device in use
Check whether a display device is in use before using it. Add a comment as
to why two displays cannot currently be used at the same time.

This allows us to remove the device-tree change that disables vopb on
jerry.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:31 -07:00
Simon Glass
c8816d1442 rockchip: Allow jerry to use of-platdata
This board always boots from SPI, so update the code to support that with
of-platdata. The boot source is not currently available with of-platdata.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:30 -07:00
Kever Yang
ae804cf4af dts: arm: rk3036: add usb vbus node
add fix regulator node for usb vbus power control.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:30 -07:00
Andreas Färber
ef904bf28e arm: rockchip: Fix typo in ROCKCHIP_RK3288 help
UART,s -> UARTs, to avoid this spreading via copy&paste.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:29 -07:00
Andreas Färber
cf78150f41 arm: dts: Fix Rockchip sort order
Sort rk3036 before rk3288.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:29 -07:00
Tom Rini
ed77ccd014 Merge git://git.denx.de/u-boot-fsl-qoriq
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	arch/arm/Kconfig
2016-11-25 17:39:54 -05:00
Alison Wang
3db86f4bbd armv8: fsl-layerscape: Support loading 32-bit OS with PSCI enabled
As PSCI and secure monitor firmware framework are enabled, this patch is
to support loading 32-bit OS in such case. The default target exception
level returned to U-Boot is EL2, so the corresponding work to switch to
AArch32 EL2 and jump to 32-bit OS are done in U-Boot and secure firmware
together.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:40:24 -08:00
Alison Wang
e2c18e40b1 armv8: fsl-layerscape: SMP support for loading 32-bit OS
Spin-table method is used for secondary cores to load 32-bit OS. The
architecture information will be got through checking FIT image and
saved in the os_arch element of spin-table, then the secondary cores
will check os_arch and jump to 32-bit OS or 64-bit OS automatically.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:40:24 -08:00
Alison Wang
ec6617c397 armv8: Support loading 32-bit OS in AArch32 execution state
To support loading a 32-bit OS, the execution state will change from
AArch64 to AArch32 when jumping to kernel.

The architecture information will be got through checking FIT image,
then U-Boot will load 32-bit OS or 64-bit OS automatically.

Signed-off-by: Ebony Zhu <ebony.zhu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:40:24 -08:00
Thomas Abraham
95e74a3df7 arm: exynos7420: remove custome low level init function
Remove the custom low-level initialization function and reuse the
default low-level initialization function. But this requires the
ARMV8_MULTIENTRY config option to be enabled for Exynos7420.

On Exynos7420, the boot CPU belongs to the second cluster and so
with ARMV8_MULTIENTRY config option enabled, the 'branch_if_master'
macro fails to detect the CPU as boot CPU. As a temporary workaround
the CPU_RELEASE_ADDR is set to point to '_main'.

Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:40:24 -08:00
Priyanka Jain
e87c673c20 armv8/fsl-lsch3: Update code to release secondary cores
NXP ARMv8 SoC LS2080A release all secondary cores in one-go.
But other new SoCs like LS2088A, LS1088A release secondary
cores one by one.

Update code to release secondary cores based on SoC SVR
Add code to release cores one by one for non LS2080A SoCs

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: remove "inline" from declaration of initiator_type]
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:38:48 -08:00
Priyanka Jain
9ae836cde7 armv8: fsl-layerscape: Add NXP LS2088A SoC support
The QorIQ LS2088A SoC is built on layerscape architecture.

It is similar to LS2080A SoC with some differences like
1)Timer controller offset is different
2)It has A72 cores
3)It supports TZASC module

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:37:54 -08:00
Priyanka Jain
d5df606d17 armv8: fsl-layerscape : Check SVR for initializing TZASC
LS2080 SoC and its personalities does not support TZASC
But other new SoCs like LS2088A, LS1088A supports TZASC

Hence, skip initializing TZASC for Ls2080A based on SVR

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:37:49 -08:00
Priyanka Jain
7cfbb4abe3 armv8: fsl-layerscape: Update TZASC registers type
TZASC registers like TZASC_GATE_KEEPER, TZASC_REGION_ATTRIBUTES
are 32-bit regsiters.
So while doing register load-store operations, 32-bit intermediate
register, w0 should be used.
Update x0 register to w0 register type.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:37:41 -08:00
Priyanka Jain
f6b96ff665 armv8: lsch3: Use SVR based timer base address detection
Timer controller base address has been changed from
LS2080A SoC (and its personalities) to new SoCs like
LS2088A, LS1088A.

Use SVR based timer base address detection to avoid compile time #ifdef.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:37:31 -08:00
Priyanka Jain
f6a70b3a92 armv8: lsch3: Add generic get_svr() in assembly
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:37:07 -08:00
Tom Rini
081abb1309 Merge branch 'master' of git://git.denx.de/u-boot-spi 2016-11-22 07:57:23 -05:00
Cédric Schieli
3e10fcde3f arm: add save_boot_params for ARM1176
Implement a hook to allow boards to save boot-time CPU state for later
use. When U-Boot is chain-loaded by another bootloader, CPU registers may
contain useful information such as system configuration information. This
feature mirrors the equivalent ARMv7 feature.

Signed-off-by: Cédric Schieli <cschieli@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
2016-11-21 14:07:31 -05:00
Tom Rini
187f9dc3f7 TI: Remove CONFIG_OMAP_COMMON in favor of CONFIG_ARCH_OMAP2
With the move to arch/arm/mach-omap2 there are now very few uses of
CONFIG_OMAP_COMMON and further they can all be replaced with
CONFIG_ARCH_OMAP2, so do so.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-21 14:07:29 -05:00
Tom Rini
983e37007d arm: Introduce arch/arm/mach-omap2 for OMAP2 derivative platforms
This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories.  All refernces to the former locations are updated to
the current locations.  For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-21 14:07:29 -05:00
Tom Rini
272686eb75 arm: Introduce ARCH_OMAP2
To start consolidating various TI-related code, introduce the ARCH_OMAP2
symbol.  While we have removed omap2-specific boards some time ago,
matching up with the kernel naming here will help overall.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-21 14:07:28 -05:00
Lokesh Vutla
140d76a9ee board: ti: amx3xx: Remove multiple EEPROM reads
Detect the board very early and avoid reading eeprom multiple times.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-21 13:59:25 -05:00
Lokesh Vutla
b64a7cb92d ARM: AMx3xx: Centralize early clock initialization
This is similar to Commit 93e6253d11 ("ARM: OMAP4/5: Centralize
early clock initialization") that was done for OMAP4+, reflecting the same
for AM33xx and AM43xx SoCs to centralize clock initialization.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add setup_early_clocks that calls setup_clocks_for_console for
        ti81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-21 13:58:55 -05:00
Shengzhou Liu
40836e215a armv8/fsl-layerscape: Update CONFIG_LS2080A to CONFIG_FSL_LSCH3
Update CONFIG_LS2080A to CONFIG_FSL_LSCH3 to make those workaround
implementing of erratum reusable for more SoCs.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-21 09:20:32 -08:00
Yuan Yao
c3aa1df28d armv8: fsl-layerscape: Add README for deploying QSPI image
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
[YS: Reviese commit subject]
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-21 09:20:32 -08:00
Hou Zhiqiang
5eef15ea9d fsl: serdes: fix a deadloop issue for P4080
This deadloop is introduced by commit:
71fe222 fsl: serdes: ensure accessing the initialized maps of serdes protocol

deadloop detail:
cpu_init_r => fsl_serdes_init => p4080_erratum_serdes_a005 =>
is_serdes_configured => fsl_serdes_init

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-21 09:20:32 -08:00
Sriram Dash
4359a3b9e4 powerpc: mpc512x: Add support for get_svr() for mpc512x devices
Defines get_svr() for mpc512x devices

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-21 09:20:32 -08:00
Priyanka Jain
fc35addea2 armv8: ls2080a: Update serdes protocol support
Add these serdes protocols
Serdes1: 0x39, 0x4B, 0x4C, 0x4D
Serdes2: 0x47, 0x57

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-21 09:20:32 -08:00
Shaohui Xie
fdc2b54cb8 armv8: ls1046aqds: add lpuart support
LPUART0 is used by default, and it's using platform clock.

Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-21 09:20:32 -08:00
Feng Li
20c700f8da armv7: Add support of ls1021a-iot board
The patch adds support for Freescale ls1021a-iot board.

Signed-off-by: Feng Li <feng.li_2@nxp.com>
[YS: rewrite commit message, fix whitespace in Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-21 09:20:32 -08:00
Lokesh Vutla
c704a99dff ARM: AMx3xx: Allow arch specific code to use early DM
Early system initialization is being done before initf_dm is being called
in U-Boot. Then system will fail to boot if any of the DM enabled driver
is being called in this system initialization code. So, rearrange the
code a bit so that DM enabled drivers can be called during early system
initialization. This is inspired by commit e850ed82bc ("ARM: OMAP4+: Allow
arch specific code to use early DM")

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-21 09:49:58 -05:00
Chris Packham
ebfa18cb3d spi: kirkwood_spi: implement mvebu_spi_set_mode()
Set the appropriate bits in the interface config register based
on the SPI_ mode flags.

Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
2016-11-18 13:04:52 +05:30
Tom Rini
9e40ea04e9 Patch queue for efi - 2016-11-17
Highlights this time around:
 
   - x86 efi_loader support
   - hello world efi test case
   - network device name is now representative
   - terminal output reports modes correctly
   - fix psci reset for ls1043/ls1046
   - fix efi_add_runtime_mmio definition for x86
   - efi_loader support for ls2080
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABAgAGBQJYLa6qAAoJECszeR4D/txgF+4QAKpHJXY/1V+McEsLga2iwePZ
 lZu5NuuLeDA9IMH+ufOOGxDIoc/llZCTsqw5l8Vnkaz0JEH6v9svyEy4zC1Nqtj2
 r4pOhGLAyVlGAh4O3hFFi/eHNEDyTrMoPO6JCy8ce+fEGE21VBlWed0+/c/KdV7F
 85joTg3X+6htFMkLybzKZS1yiJyoROe7zUZdzPrn4ogwDGbazmYbED+P2u09dDzB
 WjlpIbmEDWJEska6Cbgl/ee6dBXSVl8Q/SY3V77T5TB554sZozrKDsNUehiUMEbh
 ggCT5VzPhsm4gb/7RBpTqqCabBT5ml8iKfB8Y7fwL43sDiMXJ1LgJyVnHuz65sCS
 aPPsPjQujBSiqr+k/571yhgFNLVydrs9IYNumZr+Li4UZCvx3xtCjACJVYkbLUd1
 SZrpKts0V45nZcE4IoiwDKOUxavUbLEef2SJTOAOppB3DG9L3O0TWkyH00hTkaxR
 oDIVNSZPt9wSd4Q7FQ2MYxQ/sk+B6PrN6Gm/NMSfCnvP8DkyTzHo514qrWnEjlhQ
 ndVmyJh3hpipNDfFDeF6r5lLtPkTrzNxOVZcsUGQC5jvrvwLWguD+Kuv9Qq4gSDp
 uDawZmRwDGEGpR/yJhqj8r6/e7bZ0fOE6nPqbWLlyF+Oc4yFTz+D2CNPGR4CR0iF
 DFGQN/lNkYbu+HfyZOFO
 =xmR3
 -----END PGP SIGNATURE-----

Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot

Patch queue for efi - 2016-11-17

Highlights this time around:

  - x86 efi_loader support
  - hello world efi test case
  - network device name is now representative
  - terminal output reports modes correctly
  - fix psci reset for ls1043/ls1046
  - fix efi_add_runtime_mmio definition for x86
  - efi_loader support for ls2080
2016-11-17 11:46:45 -05:00
Alexander Graf
78d578422a armv8: fsl-layerscape: Add support for efi_loader RTS reset
When implementing efi loader support, we can expose runtime services
for payloads. One such service is CPU reset.

This patch implements RTS CPU reset support for layerscape systems.

Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-17 14:18:56 +01:00
Alexander Graf
5a37a2f014 armv8: ls2080a: Declare spin tables as reserved for efi loader
The efi loader code has its own memory map, so it needs to be aware where
the spin tables are located, to ensure that no code writes into those
regions.

Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-17 14:18:56 +01:00
Alexander Graf
b7b8410a8f ls2080: Exit dpaa only right before exiting U-Boot
On ls2080 we have a separate network fabric component which we need to
shut down before we enter Linux (or any other OS). Along with that also
comes configuration of the fabric using a description file.

Today we always stop and configure the fabric in the boot script and
(again) exit it on device tree generation. This works ok for the normal
booti case, but with bootefi the payload we're running may still want to
access the network.

So let's add a new fsl_mc command that defers configuration and stopping
the hardware to when we actually exit U-Boot, so that we can still use
the fabric from an EFI payload.

For existing boot scripts, nothing should change with this patch.

Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
[agraf: Fix x86 build]
2016-11-17 14:18:55 +01:00
Alexander Graf
441a2306ab efi_loader: Disable PSCI reset for ls1043 and ls1046
The NXP ls1043 and ls1046 systems do not (yet) have PSCI enablement
for reset. Don't enable generic PSCI reset code on them.

Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-17 14:18:50 +01:00