This allows the backend to free any resources allocated during the
relevant dfu_fill_entity_*() call. This will soon be used by the
SF backend.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
CONFIG_SYS_DFU_DATA_BUF_SIZE may be large to allow for FAT/ext layouts
to transfer large files. However, this means that individual write
operations will take a long time. Allow backends to specify a maximum
buffer size, so that each write operation is limited to a smaller data
block. This prevents the DFU protocol from timing out when e.g. writing
to SPI flash. I would guess that NAND might benefit from setting this
value too, but I can't test that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Devices are not all identified by a single integer. To support
this, defer the parsing of the device string to the IO backed, so that
it can apply the appropriate rules.
SPI devices are specified as controller:chip_select. SPI/SF support will
be added soon.
MMC devices can also be specified as controller[.hwpart][:partition] in
many commands, although we don't support that syntax in DFU.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
DFU read support appears to rely upon dfu->read_medium() updating the
passed-by-reference len parameter to indicate the remaining size
available for reading.
dfu_read_medium_mmc() never does this, and the implementation of
dfu_read_medium_nand() will only work if called just once; it hard-codes
the value to the total size of the NAND device irrespective of read
offset.
I believe that overloading dfu->read_medium() is confusing. As such,
this patch introduces a new function dfu->get_medium_size() which can
be used to explicitly find out the medium size, and nothing else.
dfu_read() is modified to use this function to set the initial value for
dfu->r_left, rather than attempting to use the side-effects of
dfu->read_medium() for this purpose.
Due to this change, dfu_read() must initially set dfu->b_left to 0, since
no data has been read.
dfu_read_buffer_fill() must also be modified not to adjust dfu->r_left
when simply copying data from dfu->i_buf_start to the upload request
buffer. r_left represents the amount of data left to be read from HW.
That value is not affected by the memcpy(), but only by calls to
dfu->read_medium().
After this change, I can read from either a 4MB or 1.5MB chunk of a 4MB
eMMC boot partion with CONFIG_SYS_DFU_DATA_BUF_SIZE==1MB. Without this
change, attempting to do that would result in DFU read returning no data
at all due to r_left never being set.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Before this patch it was only possible to access the default eMMC HW
partition. By partition selection I mean the access to eMMC via the
ext_csd[179] register programming.
It sometimes happens that it is necessary to write to other partitions.
This patch adds extra attribute to "raw" sub type of the dfu_alt_info
environment variable (e.g. boot-mmc.bin raw 0x0 0x200 mmcpart 1;)
It saves the original boot value and restores it after storing the file.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
add a possibility to add a medium specific polltimeout
function. So it is possible to define different
poll timeouts.
Used on nand medium, for setting the DFU_MANIFEST_POLL_TIMEOUT
only on nand ubi partitions, which is currently the only
usecase.
Change-Id: If1db5f49b32d93fefa7481e8dfe5b7ccc0e65af4
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Preprocessor definitions and hardcoded implementation selection in
g_dnl core were replaced by a linker list made of (usb_function_name,
bind_callback) pairs.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
When user attempted to perform a raw write using DFU (vide
dfu_fill_entity_mmc) with MMC interface not initialized before,
get_mmc_blk_size() reported invalid (zero) block size - it wasn't
possible to write ie. a new u-boot image.
This commit fixes that by initializing MMC device before use in
dfu_fill_entity_mmc().
While fixing initialization sequence, I had to change about half of
dfu_fill_entity_mmc's body, so I refactored it on the way to make it,
IMHO, considerably more comprehensible.
Being left as dead code, get_mmc_blk_size() was removed.
Tested on Samsung Goni.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
on nand flash using ubi, after the download of the new image into
the flash, the "rest" of the nand sectors get erased while flushing
the medium. With current u-boot version dfu-util may show:
Starting download: [##################################################] finished!
state(7) = dfuMANIFEST, status(0) = No error condition is present
unable to read DFU status
as get_status is not answered while erasing sectors, if erasing
needs some time.
So do the following changes to prevent this:
- introduce dfuManifest state
According to dfu specification
( http://www.usb.org/developers/devclass_docs/usbdfu10.pdf ) section 7:
"the device enters the dfuMANIFEST-SYNC state and awaits the solicitation
of the status report by the host. Upon receipt of the anticipated
DFU_GETSTATUS, the device enters the dfuMANIFEST state, where it
completes its reprogramming operations."
- when stepping into dfuManifest state, sending a PollTimeout
DFU_MANIFEST_POLL_TIMEOUT in ms, to the host, so the host
(dfu-util) waits the PollTimeout before sending a get_status again.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
move the flushing code into an extra function dfu_flush(),
so it can be used from other code.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
It is necessary to deter the host from sending subsequent DFU_GETSTATUS
request in the case of e.g. writing the buffer to medium.
Here the timeout is increased when we fill up the whole buffer. This delay
allows eMMC memory to perform its internal operations.
Otherwise we end up with HOST's error regarding GET_STATUS receive timeout.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
The method for exporting size of allocated buffer is provided.
It is afterwards used by USB's dfu function code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Define the dfu_get_buf() and dfu_free_buf() as global functions.
They are necessary for zero copy buffer management, when DFU backend is
used for storing data.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
New function - dfu_get_alt() - has been added to dfu core. If present, it
returns alt setting's number corresponding to passed name.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
The download gadget code and DFU function lacks of proper declarations
for the case when a target board wants to use only one of available usb
functions.
Moreover the relevant declarations have been moved to consistent
localization (like <dfu.h>).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
DFU spec mentions it as a method to upgrade firmware (software stored
in writable non-volatile memory). It also says other potential uses of
DFU is beyond scope of the spec.
Here such a beyond the scope use is being attempted - directly pumping
binary images from host via USB to RAM. This facility is a developer
centric one in that it gives advantage over upgrading non-volatile
memory for testing new images every time during development and/or
testing.
Directly putting image onto RAM would speed up upgrade process. This and
convenience was the initial thoughts that led to doing this, speed
improvement over MMC was only 1 second though - 6 sec on RAM as opposed
to 7 sec on MMC in beagle bone, perhaps enabling cache and/or optimizing
DFU framework to avoid multiple copy for ram (if worth) may help, and
on other platforms and other boot media like NAND maybe improvement
would be higher.
And for a platform that doesn't yet have proper DFU suppport for
non-volatile media's, DFU to RAM can be used.
Another minor advantage would be to increase life of mmc/nand as it
would be less used during development/testing.
usage: <image name> ram <start address> <size>
eg. kernel ram 0x81000000 0x1000000
Downloading images to RAM using DFU is not something new, this is
acheived in openmoko also.
DFU on RAM can be used for extracting RAM contents to host using dfu
upload. Perhaps this can be extended to io for squeezing out register
dump through usb, if it is worth.
Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Gerhard Sittig <gsi@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Heiko Schocher <hs@denx.de>
MMC and NAND independently defines same enumerators for read/write.
Unify them by defining enum in dfu header. RAM support that is being
added newly also can make use of it.
Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
New dfu_init_env_entities() function has been extracted from cmd_dfu.c and
stored at dfu core.
This is a dfu centric code, so it shall be processed in the core.
Change-Id: I756c5de922fa31399d8804eaadc004ee98844ec2
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Heiko Schocher <hs@denx.de>
Up till now the DFU maximum file size (to be written to e.g. eMMC)
was different from the DFU data buffer size. It caused errors when
one buffer was smaller than data to be written.
Now, the maximum DFU file size is equal to default DFU buffer size.
In spite of this, user is still able to manually adjust those default
values.
Change-Id: Ied75d0f7b59588ebd79dae9a22af801d36622216
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
updating an ubi partition needs a completely erased mtd partition,
see:
http://lists.infradead.org/pipermail/linux-mtd/2011-May/035416.html
So, add partubi alt setting for the dfu_alt_info environment
variable to mark this partition as an ubi partition. In case we
update an ubi partition, we erase after flashing the image into the
partition, the remaining sektors.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
This patch extends dfu code to support transmission with -R switch
specified at dfu-util.
When -R is specified, the extra USB_REQ_DFU_DETACH request is sent after
successful data transmission. Then dfu resources are released and reset
command is issued.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Dfu transfer uses a buffer before writing data to the
raw storage device. Make the size (in bytes) of this buffer
configurable through environment variable "dfu_bufsiz".
Defaut value is configurable through CONFIG_SYS_DFU_DATA_BUF_SIZE
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Tom Rini <trini@ti.com>
Support for NAND storage devices to work with the DFU framework.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Previously we didn't support upload/download larger than available
memory. This is pretty bad when you have to update your root filesystem
for example.
This patch removes that limitation (and the crashes when you transfered
any file larger than 4MB) by making raw image writes be done in chunks
and making file maximum size be configurable.
The sequence number is a 16 bit counter; make sure we handle rollover
correctly. This fixes the wrong transfers for large (> 256MB) images.
Also utilize a variable to handle initialization, so that we don't rely
on just the counter sent by the host.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
Increase size of DMA buffer from 4MiB to 8MiB. This is necessary due to
uImage size increase.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
New, separate driver at ./drivers/dfu has been added. It allows platform
and storage independent operation of DFU.
It has been extended to use new MMC level of command abstraction.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
