The EQoS interface mode is now configured in common board_interface_eth_init()
and called by EQoS MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
Now that the gwventana_emmc_defconfig is the same as the
gwventana_gw5904_defconfig we can remove the latter.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The conditions in this code do not align when doing an SPL build with
split config. Use __maybe_unused to avoid needing to be so explicit.
Of course a better solution would be to refactor all of this to avoid
using #ifdef.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add MV88E61XX DSA support:
- update dt to provide internal MDIO bus and port handles.
U-Boot requires a more restrictive subset of the dt bindings
required by Linux for the sake of simplifying code
- update defconfig to remove old driver and enable new one
- replace mv88e61xx_hw_reset weak override with board_phy_config support
for register configuration that is outside the scope of the DSA driver
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
In some situations the GSC firmware where the EEPROM containing the
model and DRAM configuration may not be ready by the time the SoC
is ready to talk to it over I2C.
Instead of a hard delay, poll the I2C lines to wait until they are
released to avoid the I2C drivers 'Arbitation lost' error message.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
As explained in the text at the bottom of the page
https://source.codeaurora.org/external/imx/imx-atf:
"QUIC repositories on this site will not receive any updates after
March 31, 2022, and will be deleted on March 31, 2023."
Point to the NXP ATF github repo instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The PCA9450 reset configuration can now be performed by the PCA9450 PMIC
driver itself, remove the hard-coded variant from board code and let the
PMIC driver perform this task using one-liner:
```
$ sed -i '/set WDOG_B_CFG to cold reset/,+2 d' $(git grep -l PCA9450_RESET_CTRL.*0xA1 board/)
```
Venice and i.MX93 EVK required slight manual fix up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
commit 0543a1ed27 ("imx8m: fixup thermal trips") moved updating the
thermal trip points to all IMX8M so we can remove it from our board
specific dt config.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW7904 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD connector with UHS support
- LIS2DE12 3-axis accelerometer
- Gateworks System Controller
- IMX8M FEC
- 2x RS232 off-board connectors
- PMIC
- 10x bi-color LED's
- 1x miniPCIe socket with PCIe and USB2.0
- 802.3at Class 4 PoE
- 10-30VDC input via barrel-jack
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW7903 has a BD71847 PMIC on I2C1. Adjust the model compare strings
to add it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Building with GCC 12.2 results in an error
board/gateworks/gw_ventana/gw_ventana.c:636:68: error: the comparison
will always evaluate as 'true' for the address of 'pwm_padmux' will
never be NULL [-Werror=address]
636 | } else if (hwconfig_subarg_cmp(arg, "mode", "pwm") &&
| ^~
Remove the superfluous check.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-By: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Fix the MMC env device for boards with eMMC by adding a
board_mmc_get_env_dev override to return the boot device as the
MMC env device.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Update the GW74xx PMIC configuration:
- increase VDD_SOC DVS1 to 0.85V per datasheet
- increase VDD_SOC DVS0 to 0.95V before first DRAM access
- increase VDD_ARM DVS0 to 0.95V to support kernel overdrive voltage (OD)
- remove unnecessary changes to VDD_DRAM as we don't use 3GHz DRAM
- remove unnecessary change to LDO2 as it is unused
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
v2: update commit log with more detail
The GW73xx-C revision and onward replaced the 5-port PCIe switch with a
4-port (dropping PCIe to one of the miniPCIe sockets) due to part
availability. This moved the PCI bus of the GbE eth1 device. Use a fixup
to adjust the dt accordingly so that local-mac-address assigned from dt
works on new revision boards.
While we are at it, rename 'blob' to 'fdt' for clarity.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Move the environment text over from being set via
CONFIG_EXTRA_ENV_SETTINGS in include/configs/gw_ventana.h and over
to plain text in board/gateworks/gw_ventana/gw_ventana.env. This lets
us drop CONFIG_EXTRA_ENV_SETTINGS_COMMON as everything resides in a
single environment file now.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
commit 61cf225053 ("board: gateworks: gw_ventana: use comomn GSC driver")
moved to the common GSC driver and moved remaining board-specific
functions to eeprom.c. The functions in gsc.c are no longer used and it
was removed from the Makefile but the file itself was not removed.
Remove it now.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The MaxLinear GPY111 PHY is being used on some boards due to part
availability. Add support for this PHY which requires a longer reset
post-delay and RGMII delay configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The uart2 and its pinmux are already marked with u-boot,dm-spl but we
need to move the call to preloader_console_init() after spl_early_init()
to avoid a board hang as dm can't be used until after spl_early_init()
due to the uart driver not enabling the uart clock.
Remove the manual config of the UART pinmux now that it is no longer
needed.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This function is empty, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Gateworks produces many products from a single PCB with subloaded
components. Add an additional two levels of dtb name matching so that
for example a GW7400-A matches the dtb name of gw74xx.dtb
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- use the GSC driver functions
- move waiting for the EEPROM to the SPL int (it will always be ready
after this)
- move eeprom functions into eeprom file and elimate GSC_I2C_BUS
- eliminate some redundant EEPROM reads (the EEPROM must be read in
SPL before relocation, in SPL after relocation, and in U-Boot init.
All subsequent uses can use the global structure)
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- rename gsc{.c,.h} to eeprom{.c.h} for clarity
- collapse eeprom_get_dev
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW7903 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD socket with voltage select support
- Gateworks System Controller
- M.2 A-E Socket with USB2.0 and PCIe
- MiniPCIe Socket with PCIe, USB2.0, and SIM
- IMX8M FEC
- RS232/RS485/RS422 serial transceiver
- LIS2DE12 3-axis accelerometer
- front panel LED's
- off-board isolated digital I/O
- Wide range DC power input
- 802.3at PoE
- PMIC
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The TI DP83867 phy has been replaced with the MaxLinear GPY111 phy due
to part availability.
Add support for it by adding LED config and dt-prop based internal delay
config tx-delay/rx-delay per PHY ID.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
DM is not used for the SPL and a generic DT is used in the SPL
which requires no fixups. Remove the call in the SPL and move the function
into the U-Boot code.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Since DM_SERIAL is used for U-Boot we no longer need legacy UART code in
common.c shared by the SPL and U-Boot. Move the legacy UART config to
the non-DM SPL.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
convert to DM_I2C for U-Boot while leaving SPL legacy I2C:
- Move I2C config from common to SPL
- Move PMIC config from common to SPL (no need to re-configure pmic)
- add DM_I2C support to eeprom/gsc functions shared by SPL and U-Boot
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The SPL does not update the memory node with the dram size from EEPROM
but instead we can use get_ram_size which does a simple memory test
to determine the available RAM. Update PHYS_SDRAM_SIZE to 4GiB as that
is the max used on the Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
commit 7c84319af9c7 ("dm: gpio: Correct use of -ENODEV in drivers")
changed the return code for an I2C NAK from -ENODEV to -EREMOTEIO.
Update the gsc_i2c_read and gsc_i2c_write functions for this change
to properly retry the transaction on a NAK meaning the GSC is busy.
Fixes: 7c84319af9 ("dm: gpio: Correct use of -ENODEV in drivers")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use binman to pack images.
Note that imx8mm_venice supports several boards via multiple DTB's thus
in the fit node we must use:
- fit,fdt-list = "of-list"
- fdt-SEQ
- config-SEQ
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Since no one uses this feature and I am not aware of any parsers of this
in Linux, remove it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove board_ehci_hcd_init function that is not used with DM_USB
and replace its functionality with device-tree configuraton that treats
USB HUB RST# as a gpio enable for the usbh1 vbus regulator.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable LVDS display detection and panel-specific configuration
Make I2C based LVDS detection and configuration model specific:
- not all boards support LVDS connectors; fail detection that do not
support LVDS to avoid misdetecting an I2C device as a display
- GPIO configuration is panel specific; use panel name where needed
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
We configure network phy configuration for internal delay, LED config,
and clock config. If we leave the phy reset gpio defined in dt the
kernel may issue a reset to the phy and break these configs. While some
may be handled by a kernel phy driver, others may not (typically LED
config).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
