Please pull the updates for rockchip platform:
- Add board support:
RK3566: Radxa ROCK 3 Model C
Radxa ZERO 3W/3E
Xunlong Orange Pi 3B
RK3568J: Radxa ROCK 3B
RK3308B: Radxa ROCK S0
RK3588: Radxa ROCK 5 ITX
FriendlyElec CM3588 NAS board
- dw-mmc: allow 4-bit mode;
- dts and config updates;
CI:
https://source.denx.de/u-boot/custodians/u-boot-rockchip/-/pipelines/21997
USB Type-C port is configured as "peripheral" port. so enable "ums"
command to use as USB Mass Storage device.
("rockusb" command is already enabled and working)
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the commit 6afdb15851 ("dm: core: migrate debug() messages to use
dm_warn") use of DM_WARN/SPL_DM_WARN print a lot of debug messages.
Disable the SPL_DM_WARN Kconfig option to remove verbose logging and
restore normal serial console output during boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rock 5 ITX is a board in ITX form factor using the RK3588 SoC
It can be powered either by 12V, ATX power-supply or PoE.
Notable peripherals are the 4 SATA ports, M.2 M-Key slot, M.2 E-key slot,
2*2.5Gb PCIe-connected Ethernet NICs.
Display options are 2*HDMI, DP via USB-c, eDP + 2*DSI via PCB connectors.
USB ports are 4*USB3 + 2*USB2 on the back panel and 2-port front-panel
connector.
Schematics for the board can be found on
- https://dl.radxa.com/rock5/5itx/radxa_rock_5_itx_X1100_schematic.pdf
- https://dl.radxa.com/rock5/5itx/v1110/radxa_rock_5itx_v1110_schematic.pdf
The naming scheme with the dashes follows Dragan's comment on the mainline
devicetree commit:
"the name of this board deviates from the standard Radxa naming scheme,
which is something like "ROCK <number><letter>" thus, "rock-5a" is
fine, but it should be "rock-5-itx", simply because there's a space
between "5" and "ITX" in "ROCK 5 ITX"
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
EFI HTTP is a useful option to have by default and is working reliably on
QEMU. Let's enable it by default, since we have no size limitations.
While at it enable 'efidebug' as well, which is currently needed to
configure the EFI HTTP boot options.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The CM3588 NAS by FriendlyElec pairs the CM3588 compute module, based
on the Rockchip RK3588 SoC, with the CM3588 NAS Kit carrier board.
Features tested on a CM3588 NAS Kit with 8GB RAM 64GB eMMC module:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Xunlong Orange Pi 3B is a single-board computer based on the
Rockchip RK3566 SoC.
The two hw revisions use different io-voltage for Ethernet PHY and can
be identified using GPIO4_C4:
- v1.1.1: x (internal pull-down)
- v2.1: PHY_RESET (external pull-up)
Implement rk_board_late_init() to set correct fdtfile env var and
board_fit_config_name_match() to load correct FIT config based on what
board is detected at runtime so a single board target can be used for
both hw revisions.
Minimal DTs that includ DT from dts/upstream is added to support booting
from both hw revision and only set Ethernet PHY io-voltage when the hw
revision is detected at runtime. A side-affect of this is that defconfig
show OF_UPSTREAM=n, however dts/upstream DTs is used for this board.
Features tested on Orange Pi 3B 4GB (v1.1.1 and v2.1):
- SD-card boot
- eMMC boot
- SPI Flash boot
- Ethernet
- PCIe/NVMe
- USB host
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
Co-developed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Radxa ZERO 3W/3E is an ultra-small, high-performance single board
computer based on the Rockchip RK3566, with a compact form factor and
rich interfaces.
Implement rk_board_late_init() to set correct fdtfile env var and
board_fit_config_name_match() to load correct FIT config based on what
board is detected at runtime so a single board target can be used for
both board models.
Features tested on a ZERO 3W 8GB v1.11:
- SD-card boot
- eMMC boot
- USB gadget
- USB host
Features tested on a ZERO 3E 4GB v1.2:
- SD-card boot
- Ethernet
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Radxa ROCK 3B is a single-board computer based on the Pico-ITX form
factor (100mm x 75mm). Two versions of the ROCK 3B exists, a community
version based on the RK3568 SoC and an industrial version based on the
RK3568J SoC.
Features tested on ROCK 3B 8GB v1.51 (both variants):
- SD-card boot
- eMMC boot
- SPI Flash boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa ROCK S0 is a single-board computer based on the Rockchip RK3308B
SoC in an ultra-compact form factor. Add a board target for the board.
Features tested on a ROCK S0 v1.2 with 512 MiB RAM and 8 GiB eMMC:
- SD-card boot
- eMMC boot
- Ethernet
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add LED=y and LED_GPIO=y to support the onboard leds.
Add ROCKCHIP_IODOMAIN=y to configure correct io voltage domains.
Add DM_MDIO=y now that the DT contain a Ethernet phy node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3399 Puma has support for driving multiple displays at the same time,
the most notable scenario being HDMI+DSI since there exists a devkit
with both DSI display and HDMI output.
While HDMI seems to work fine in U-Boot, as the U-Boot logo is shown
whenever the EFI bootmeth is used, it messes up DSI in HDMI+DSI setup in
the Linux kernel. There are some ways to work around this bug but no
known appropriate fix for now, so let's rather not trigger this bug.
Since there isn't any client of ours that seems to be using this
feature, let's disable it for now. Users can re-enable this feature in
the event they have HDMI-only products.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for Rockchip Toybrick TB-RK3588X has been merged into
dts/upstream with devicetree-rebasing v6.10-dts, migrate board to
OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for Pine64 PineTab2 has been merged into dts/upstream
with devicetree-rebasing v6.10-dts, migrate board to OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This updates the "old style" DTs to that of Linux v6.10, matching what
OF_UPSTREAM is at now. Hopefully we won't need to do this (manually)
anymore. Since this brings in the DT for a new board (Tanix TX1), also
add the defconfig for that, which has just been waiting for that sync.
There are three more fixes: two for the SPI clock setup, which avoids
too high frequencies in some cases, and one fix to avoid a build warning
with GCC 14 for the sunxi TOC0 part of the mkimage tool.
The gitlab CI passed, and I tested the SPI flash on the OrangePi Zero 3
and also booted that into Linux.
amd/xilinx:
- Enable CONFIG_MMC_SPEED_MODE_SET
env:
- support overriding spi dev from board code
clk:
- Add set_rate support for display clocks
spi:
- Describe is25lp01gg flash
zynq:
- Add support for 7z010_lr and 7z020_lr
zynqmp:
- Add support for zu1eg_lr
- Enable NFS for Kria
- DT changes
- Cleanup firmware handling in board_init()
versal-net:
- Setup spi seq number based on boot device
- dt-schema update for mini configurations
versal2:
- Disable uartlite driver
- Add support for mini configurations
- Enable NFS
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZrDqGAAKCRDKSWXLKUoM
IcleAKCMngdmRjasxRh+6CmntS1Q7KhUdwCcCaTPbn5x5eLT4QbsH05x2dJh6UM=
=pQP2
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.10-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
AMD/Xilinx changes for v2024.10-rc2
amd/xilinx:
- Enable CONFIG_MMC_SPEED_MODE_SET
env:
- support overriding spi dev from board code
clk:
- Add set_rate support for display clocks
spi:
- Describe is25lp01gg flash
zynq:
- Add support for 7z010_lr and 7z020_lr
zynqmp:
- Add support for zu1eg_lr
- Enable NFS for Kria
- DT changes
- Cleanup firmware handling in board_init()
versal-net:
- Setup spi seq number based on boot device
- dt-schema update for mini configurations
versal2:
- Disable uartlite driver
- Add support for mini configurations
- Enable NFS
The Tanix TX1 is a tiny TV box, featuring the Allwinner H313 SoC with up
to 2GB of DRAM and 16GB of eMMC. There is no SD card or Ethernet port on
this small device, but it can be booted via the USB debug "FEL" mode.
The bootloader could then be written to the eMMC.
Add the defconfig for that board, and add the devicetree file to the
Makefile, for it to be built.
The DRAM parameters were taken from the vendor firmware on the eMMC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Enabled the default utilization of the NFS command on Versal Gen 2
platform to facilitate booting images through the network using
the NFS protocol
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20240711165734.1561933-1-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enabled the default utilization of the NFS command on ZynqMP Kria
platforms to facilitate booting images through the network using
the NFS protocol.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20240709042232.860395-1-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enable setting speed mode using mmc dev commands.
The speed mode is provided as the last argument in these commands
(ex: mmc dev 0 0 10) and is indicated using the index from enum
bus_mode in include/mmc.h. A speed mode can be set if it is enabled
from device tree or from capabilities register
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240708091755.5021-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This change adds support for PCIe connected nvme disk - phyBOARD-Polis
base board.
One needs to call following commands in u-boot:
> pci enum
> nvme scan
> nvme info
And then ones to access proper file system (like fat[ls|load|write],
ext4[ls|load|write]).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Enable the 'cpu' command to display the CPU info and release CPU core to
run baremetal or RTOS applications.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Enable the 'cpu' command and the depended imx CPU driver to
display the CPU info and release CPU core to run baremetal
or RTOS applications.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Instead of using the local imx7s-warp devicetree copies from U-Boot,
convert the imx7s-warp board to OF_UPSTREAM so that the upstream
kernel devicetree can be used instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
* Qualcomm platforms >~2016 gain support for the RPMh (Resource Power Manager)
peripheral which is used to control most regulators. The RB5 is now able to
power up its USB VBUS regulator via the rpmh regulator driver. Git history
from the original Linux driver is preserved for ease of maintenance.
* IPQ40xx SoCs gain ethernet networking support via the new ESS EDMA driver.
Enable True Random Number Generator (TRNG) on E850-96 board. To do so:
1. Enable DM_RNG and RNG_EXYNOS for TARGET_E850_96
2. Add TRNG node to E850-96 device tree
3. Enable 'rng' command support for easy TRNG testing
TRNG node is already applied in Linux kernel device tree, but it hasn't
appeared in upstream dts yet. Add it in U-Boot override dtsi file
temporarily; it can be removed once it appears in upstream dts.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The conversion to DM_I2C is mandatory, rework to remove
use of legacy I2C API.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Cc: Holger Brunck <holger.brunck@hitachienergy.com>
Cc: Tomas Alvarez Vanoli <tomas.alvarez-vanoli@hitachienergy.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/21728
- Conversions to DM_I2C and DM_SERIAL.
- Support for I2C3 and PWM1 for the imx6q clock driver.
- Improvements for udoo-neo
- Describe the i.MX93 CPU clocks in the devicetree to fix CPU clock printing
- Fix for SPI and NANC clk-imx8mn clock driver
Rework to remove use of legacy I2C API. Also switch
to DM_SERIAL to avoid board removal warning.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Rework to remove use of legacy I2C API. Also switch
to DM_SERIAL to avoid board removal warning.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
