- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a proper Kconfig option for SPL so we can remove the hack in some of
the board config files.
This involves adding CONFIG_SPL_DM_PMIC to some of the configs as well
as updateing the Makefile rule for PMIC_RK8XX to exclude SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Add SPL_PMIC_RK8XX, enable when needed, handle undef of
CONFIG_DM_PMIC_PFUZE100 as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards aren't ChromeOS devices so won't have a cros-ec-keyb
input as it's the keyboard available via the ChromeOS Embedded
Controller. Update them to use a USB keyboard which would actually
be available. Also enable the usb keyboard option for those devices
that don't have it enabled already.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3288, RK3399 are now support cpu-info, so enable
DISPLAY_CPUINFO by default.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
Select CONFIG_FASTBOOT_FLASH, CONFIG_FASTBOOT_FLASH_MMC_DEV
for rockchip SoC plaforms in fastboot Kconfig file instead
of defined it in board defconfig.
This eventually drop the explicit configs defined in
supporting board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip support differnet or common gadget product number
between Rockchip SoCs like,
0x310a - rk3036
0x320a - rk3229, rk3288
0x330a - rk3328
So, select them on Kconfig based on platform specific
config defined.
This eventually drop the explicit configs defined in
supporting board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Gadget vendor number, 0x2207 is common across all platfroms
supported in Rockchip SoC.
So, select the same number globally, if ARCH_ROCKCHIP.
This eventually drop the explicit configs defined in supported
board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Select the gadget manufacturer as 'Rockchip' for
all rockchip platform SoC's.
This eventually drop the explicit defined added
on supported board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This is currently a decimal value which is not as convenient or
meaningful. Also U-Boot tends to use hex everywhere.
Convert this option to hex and add a comment for the size_check macro.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the typo in the commit title]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tinker board needs to mux all the sdmmc gpio and
activate the regulator connected to bank 7. Remove
all the bank that are not in use and mark them as dm,spl
so-that it would initialize at SPL.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
SPL sets up SDRAM while in its board_init_f()
function, it is possible for the stack to move
there before board_init_r() is reached.
So it is required to reserve the stack for SDRAM,
with a proper location and size otherwise any
operations during SPL handoff would leads to failure.
On, this particular context tinker-rk3288 SPL is
failing to launch U-Boot proper on SDRAM due to
lack of stack.
U-Boot SPL 2019.10-rc3-00297-g5ba8b12543 (Sep 12 2019 - 08:50:36 +0530)
Trying to boot from MMC1
spl: mmc init failed with error: -110
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
So, enable SPL_STACK_R_ADDR and it's related-config
items for SDRAM, SPL stack to setup properly.
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
SPL_TEXT_BASE is 0x0 by default, based on the kconfig
definition move in below commit.
"configs: move CONFIG_SPL_TEXT_BASE to Kconfig"
(sha1: f89d6133ee)
So, don't define it explicitly.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
This affects RK3036, RK322X and RK3288 - the defconfig changes done by
moveconfig.py for the veyrons were left out on purpose because they dont
have an OTG port, and will get their config updated in the next commit.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT
Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.
Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to update TEXT BASE for TPL/SPL/U-Boot;
SPL no need relocate STACK after enable TPL, so remove it;
Don't enable pinctrl names so that SPL can get pinctrl dts;
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The SPL for the Tinker Board has to fit into 32 KiB. Currently this limit
is exceeded.
CONFIG_SPL_I2C_SUPPORT is not needed to move to main U-Boot. So let's
disable it.
Suggested-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The SPL image for the Tinker Board has to fit into 32 KiB. This includes
up to 2 KiB for the file header.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
