This patch adds support for the sgmii phy interface,
available only to DM users, dictated by current driver
design.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
macb.h provides macros for reading/setting bitfields,
in macb registers and descriptors. use that instead
of redefining them in the source file.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
add support for clock rates higher than 2.4Mhz
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Few registers and bits were added by Cadence and
they were not updated in the headers.
Take the latest definitions as defined in Linux
header (5.1) that also includes some comments
about existing registers.
One register was improperly named (UR), fix that.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This driver is used for MDIO muxes driven over I2C. This is currently
used on Freescale LS1028A QDS board, on which the physical MDIO MUX is
controlled by an on-board FPGA which in turn is configured through I2C.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Using 'phy_connect' instead of 'phy_find_by_mask' and 'phy_connect_dev'
both deduplicates code and adds support for 'fixed-link'.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
SGMII 2500 as supported on NXP SoCs requires AN to be disabled, handle
this case in the enetc sgmii init code.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Ethernet interfaces using serial protocols go through the serdes block
integrated in the SoC. This is accessed over dedicated internal MDIOs
which are part of the Ethernet PCI functions. Set up serdes at _start,
along with other protocol specific port/MAC configuration.
MDIO code is shared with enetc_mdio, read/write functions are exported
from fsl_enetc_mdio for this reason.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a driver for the MDIO interface currently integrated in LS1028A SoC.
This MDIO interface is shared by multiple ethernet interfaces and is
presented as a stand-alone PCI function on the SoC ECAM.
Ethernet has a functional dependency on MDIO, for simplicity there is a
single config option for both.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a driver for NXP ENETC ethernet controller currently integrated in
LS1028A. ENETC is a fairly straight-forward BD ring device and interfaces
are presented as PCI EPs on the SoC ECAM.
Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com>
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since u-boot has added the spi-mem framework and replaced
the spi-nor framework, the mtk_qspi is no longer compatible
with the new spi-nor driver.
Remove this driver along with replacing config item
with new mtk spi-nor driver.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
[jagan: squash related changes and update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reduce power domain calls when CONFIG_POWER_DOMAIN is disabled.
With gcc v8.2, this change saves 104 bytes.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Right now when using clk_of_xlate_default(), clk->data
remains un-initialized because clk_get_bulk() does not
initialize memory on allocation of clock structure.
This can cause problems when data is used to match if
two clocks pointers are exactly the same underlying
clocks, for example.
Fix it by initializing clk->data to 0.
Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Per device tree spec, "status" property can have a value of "okay",
or "disabled", but not "disable".
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Without a valid ofnode, it's meaningless to call clk_set_defaults()
to process various properties.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is possible that a timer device has a null ofnode, hence there is
no need to further parse DT for the clock rate.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In spite of the summary line, U-Boot commits [1-2] seem to have
aligned the U-Boot PFC tables to Linux v5.1 rather than to v5.0, since
they also imported the Linux 5.1 commits listed in [3].
What current commit tries to accomplish is to align the Gen2 and Gen3
pinctrl tables to Linux v5.2. Importing these updates in two steps
as done before (i.e. separately for Gen2 and Gen3) is somewhat difficult
due to Linux commits like [5-6] which atomically update both Gen2/3
platforms and whose breakdown would not be easily possible.
The detailed list of Linux commits squashed into this U-Boot patch is
shown in [4]. The second column in [4] depicts the patch id mismatch
between the original Linux and the resulted U-Boot commit. The
exclamation mark means that manual conflict resolution was involved
during cherry picking Linux commit into U-Boot repository (this is
mainly caused by dropped changes in files like pfc-r8a7795-es1.c and
pfc-r8a77980.c which are missing in U-Boot).
This patch has been applied on top of v2019.07-rc4-155-g8754656680b6 and
boot-tested on:
- H3-ES2.0-Salvator-X
- M3-ES1.1-Salvator-XS
- M3N-ES1.1-ULCB
[1] 8719ca8113 ("pinctrl: renesas: Synchronize Gen3 tables with Linux 5.0")
[2] a6a743df24 ("pinctrl: renesas: Synchronize Gen2 tables with Linux 5.0")
[3] Linux 5.1 commits already contained in [1-2]:
79dbbdbeccc6784 pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions
729257d674bc2e6 pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions
b9fd50488b4939c pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group
a4b0350047f1b10 pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group
fdbbd6b74c9278f pinctrl: sh-pfc: r8a77990: Add DRIF pins, groups and functions
16978e7d40f73be pinctrl: sh-pfc: r8a77990: Add TMU pins, groups and functions
86c045c2e4201e9 pinctrl: sh-pfc: r8a77965: Replace DU_DOTCLKIN2 by DU_DOTCLKIN3
b8ba194ca5f4ca2 pinctrl: sh-pfc: r8a7791: Fix VIN1 versioned groups
81c585c96b7dd47 pinctrl: sh-pfc: r8a77970: Deduplicate VIN[01] pin definitions
08b7e2112a9b19c pinctrl: sh-pfc: r8a7796: Deduplicate VIN5 pin definitions
99fdb920f5534d1 pinctrl: sh-pfc: r8a7795: Deduplicate VIN5 pin definitions
85ccae133bde425 Revert "pinctrl: sh-pfc: r8a77990: Add support for pull-up only pins"
f7d8b568e204d29 pinctrl: sh-pfc: r8a77990: GP6_9 does not have pull-down capability
5219aa33caec2f7 pinctrl: sh-pfc: r8a77995: Fix MOD_SEL bit numbering
3e3eebeacad79bd pinctrl: sh-pfc: r8a77990: Fix MOD_SEL bit numbering
7219a4b64520873 pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 bit2 when using RX2, TX2 and SCK2
699c7d1346fbef6 pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 bit3 when using TX0
[4] Linux 5.2 commits backported and squashed into this U-Boot patch
Linux commit id Linux commit summary line
9925e8795726801 pinctrl: sh-pfc: Validate pins/marks in pin groups at build time
f83f97684a737f6 pinctrl: sh-pfc: Make pinmux_cfg_reg.var_field_width[] variable-length
5e8588c86d71e78 pinctrl: sh-pfc: Validate fixed-size field widths at build time
1c5c1101755c5ed pinctrl: sh-pfc: r8a77970: Rename IOCTRLx registers
3df892fdbfe6919 pinctrl: sh-pfc: r8a77990: Rename IOCTRLx registers
dcd24e098d8df8b pinctrl: sh-pfc: r8a7796: Move CANFD pin groups and functions
2cee6cb290ab30f pinctrl: sh-pfc: r8a77990: Move CANFD pin groups and functions
d92ee9cf8ec8d7f ! pinctrl: sh-pfc: rcar-gen3: Retain TDSELCTRL register across suspend/resume
efca8da0c5fcc7f ! pinctrl: sh-pfc: Absorb enum IDs in PINMUX_CFG_REG() macro
69f7be1c6314fb0 ! pinctrl: sh-pfc: Absorb enum IDs in PINMUX_CFG_REG_VAR() macro
19b593a1cf068ef ! pinctrl: sh-pfc: Absorb enum IDs in PINMUX_DATA_REG() macro
c481c8178420b8c pinctrl: sh-pfc: Validate enum IDs for regs with fixed-width fields
fa4d36712f20e24 ! pinctrl: sh-pfc: Validate enum IDs for regs with variable-width fields
360328c7dc15f48 pinctrl: sh-pfc: Improve PINMUX_IPSR_PHYS() documentation
943ff71281c6ce4 pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 bit16 when using NFALE and NFRB_N
e167d723e1a472d pinctrl: sh-pfc: r8a77990: Fix MOD_SEL1 bit31 when using SIM0_D
e87882eb9be10b2 pinctrl: sh-pfc: r8a77990: Fix MOD_SEL1 bit30 when using SSI_SCK2 and SSI_WS2
5671f8e0270ad5e ! pinctrl: sh-pfc: rcar-gen3: Remove HDMI CEC pins, groups, and functions
662dc924a05e9df ! pinctrl: sh-pfc: rcar-gen3: Remove CC5_OSCOUT pin
624a7a12cc0cc77 ! pinctrl: sh-pfc: rcar-gen3: Rename RTS{0,1,3,4}# pin function definitions
a040f3dec8eb7b1 pinctrl: sh-pfc: rcar-gen3: Rename SEL_ADG_{A,B,C} to SEL_ADG{A,B,C}
e551122cdb7fcb9 pinctrl: sh-pfc: rcar-gen3: Rename SEL_NDFC to SEL_NDF
baaa2effc684e49 pinctrl: sh-pfc: r8a77970: Fix spacing
f05603fa6aa3043 pinctrl: sh-pfc: r8a7796: Remove placeholder I2C pin data
0a042b355e60269 pinctrl: sh-pfc: r8a77965: Add I2C{0,3,5} pins, groups and functions
[5] efca8da0c5fcc7 ("pinctrl: sh-pfc: Absorb enum IDs in PINMUX_CFG_REG() macro")
[6] 69f7be1c6314fb ("pinctrl: sh-pfc: Absorb enum IDs in PINMUX_CFG_REG_VAR() macro")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
mt35xu512aba and mt35xu02g suports Single I/O and OCTAL I/O
also enable use of SPI_NOR_4B_OPCODES.
These flashes are tested on LX2160ARDB and LS1028ARDB respectively
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[jagan: suffix 'ba' on part name and update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add RTCAPB and RTC clock support.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch introduces support of Cortex-M4 remote processor for STM32
MCU and MPU families.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
The current implementation supports only binary file load.
Add helpers to support ELF32 format (sanity check, and load).
Note that since an ELF32 image is built for the remote processor, the
load function uses the device_to_virt ops to translate the addresses.
Implement a basic translation for sandbox_testproc.
Add related tests. Test result:
=> ut dm remoteproc_elf
Test: dm_test_remoteproc_elf: remoteproc.c
Test: dm_test_remoteproc_elf: remoteproc.c (flat tree)
Failures: 0
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add the following functions to translate DMA address to CPU address:
- dev_translate_dma_address()
- ofnode_translate_dma_address()
- of_translate_dma_address()
- fdt_translate_dma_address()
These functions work the same way as xxx_translate_address(), with the
difference that the translation relies on the "dma-ranges" property
instead of the "ranges" property.
Add related test. Test report:
=> ut dm fdt_translation
Test: dm_test_fdt_translation: test-fdt.c
Test: dm_test_fdt_translation: test-fdt.c (flat tree)
Failures: 0
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
- rk3399 lpddr4 support
- rk3399-rock960 board support improvement
- Eliminate pyelftools dependency by make_fit_atf.py
- clean up rockchip dts to use -u-boot.dtsi
- use ARM arch/generic timer instead of rk_timer
- clean up Kconfig options for board support
Pin configuration of the FPGA devicetree block should be done
after core configuration in the arria10 fpga driver. This fix
corrects the check of status, and ensures that the fpga pin mux
is configured on correct configuration of the core fpga image.
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
This adds separate kconfig options for drivers/sysreset and
drivers/firmware.
Up to now, CONFIG_SPL_DRIVERS_MISC_SUPPORT added drivers/misc to SPL
build but also added drivers/firmware and drivers/sysreset at the same
time.
Since that is confusing, this patch uses CONFIG_SPL_SYSRESET for
drivers/sysreset and adds CONFIG_SPL_FIRMWARE for
drivers/firmware (and accordingly for the TPL options).
CONFIG_SPL_DRIVERS_MISC_SUPPORT stays for including drivers/misc into
the SPL build (and accordingly for TPL) since there are boards using
non-DM (non UCLASS_MISC) files from drivers/misc. Such boards don't
have CONFIG_SPL_MISC enabled, so cannot use this to include
drivers/misc into the SPL build.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This moves sysreset support for socfgpa from ad-hoc code in mach-socfpga
to a UCLASS_SYSRESET based dm driver.
A side effect is that gen5 and a10 can now select between cold and warm
reset.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This driver uses bss from SPL board_init_f(). Change it to move all the
data from bss to a common struct allocated on the stack (64 byte).
In addition to saving 28 bytes of bss, the code even gets 264 bytes
smaller.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This patch fix mmc driver abort caused by below patch:
3d296365e4 mmc: sdhci: Add support for sdhci-caps-mask
After the patch sdhci_setup_cfg() access to host->mmc->dev,
so we have to do init before make the call to the function()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The RK3288 HDMI driver's rk3288_hdmi_enable() currently lacks a call to
dw_hdmi_enable(). Thus, the HDMI output never gets enabled.
Signed-off-by: Niklas Schulze <me@jns.io>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Unlike rest of dram type chips, LPDDR4 initialization start
with at board selected frequency (say 50MHz) and then it
switches into 400MHz and 800MHz simultaneously to make the
proper sequence work on each channel with associated training.
The lpddr4 set rate sequnce will follow by setting lpddr4
- dq out
- ca odt
- MR3
- MR12
- MR14
registers sets in sequential order.
Here is sameple log about LPDDR4-100 init sequence in Rockpro64:
Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
256B stride
channel 0 training pass
channel 1 training pass
change freq to 400 MHz 0, 1
channel 0 training pass
channel 1 training pass
change freq to 800 MHz 1, 0
This patch add support to this init sequence via lpddr4 set rate
by taking sdram timing parameters from 400, 800 .inc files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Fix travis error, use one ret instead of ret[2] in set_ctrl)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
DDR set rate can be even required for lpddr4 and we
need to keep the lpddr4 code to compile only for relevant
boards which do support lpddr4.
For this requirement, and for code readability handle
data training via sdram_rk3399_ops with .set_rate and
same will update in future while supporting lpddr4 code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
LPDDR4 initialization start with at board selected frequency
and then it switches into 400MHz and 800MHz simultaneously to
make the proper sequence work on each channel with associated
training.
So, add LPDDR4-800 timings inc file in driver area so-that
these timings will take during LPDDR4 initialization phase.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
LPDDR4 initialization start with at board selected frequency
and then it switches into 400MHz and 800MHz simultaneously to
make the proper sequence work on each channel with associated
training.
So, add LPDDR4-400 timings inc file in driver area so-that
these timings will take during LPDDR4 initialization phase.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add support for setting 400MHz ddr clock.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add support for setting 50MHz ddr clock.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Like data training in other sdram types, mr detection need
to taken care for lpddr4 with looped rank and associated
channel to make sure the proper configuration held.
Once the mr detection successful for active and configured
rank with channel number, the same can later reused during
actual LPDDR4 initialization.
So, add code to support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
data training can be even required for lpddr4 and we
need to keep the lpddr4 code to compile only for relevant
boards which do support lpddr4.
For this requirement, and for code readability handle
data training via sdram_rk3399_ops and same will update
in future while supporting lpddr4 code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
data training is using chan_info as first argument with
channel number as second argument instead of that use
dram_info as first argument so-that we can get the
chan_info at data training definition.
This was the argument handling is meaningful, readable
and it would help to add similar data training for
lpddr4 in future.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Update vref_mode_ac for lpddr4 based on VDDQ/3/2=16.8%
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
The mode_sel on lpddr4 value is depending on IO settings
of rd_vref.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
The vref_mode_dq, vref_value_dq on lpddr4 value is depending
on IO settings of rd_vref.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
For base.odt 1 the lpddr4 tsel_rd_en value is depending
on IO settings of rd_odt_en.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
CTL 145, 146, 159, 160 registers are used to configure
soc odt on rk3399.
These soc odt values are updated from CS0_MR22_VAL and
CS1_MR22_VAL and for lpddr4 these values ORed with
tsel_rd_select_n.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
tsel contrl clock drives are required to configure PHY
929, 939 controls drive settings.
Add support for these control clock for all dramtype
sdrams.
Thse control clock drives are configure via tsel_ckcs_select_p
and tsel_ckcs_select_n variables.
tsel_ckcs_select_n is PHY_DRV_ODT_34_3 value where as
tsel_ckcs_select_p is retrived from IO settings for lpddr4
and rest uses PHY_DRV_ODT_34_3.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Now we have IO settings available for all supported sdram
frequencies, so retrieve these IO settings and make used
for LPDDR4 ds odt configuration.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Add IO settings for dram ctl and phy.
IO settings are useful for configuring ctl, phy odt, vref,
mr5, mode select and other needed input output operations
for lpddr4 or any other dramtype sdram.
Right now, this patch added IO setting for all supported
sdram frequencies.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
The hardware for LPDDR4 with
- CLK0P/N connect to lower 16-bits
- CLK1P/N connect to higher 16-bits
and usually dfi dram clk is configured via CLK1P/N, so
disabling dfi dram clk will disable the CLK1P/N as well.
So, add patch to not to disable dfi dram clk for lpddr4,
with rank 1.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
tsel write ca_p and ca_n values need to write on PHY 544, 672
and 800 to configure ds odt.
Configure the same PHY register for lpddr4 would require a mask
value of (300 << 8).
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Assign desired cs_map values for lpddr4 during set memory map.
Initial cs_map values is based on the sdram parameters, so
the same will adjusted based dramtype as LPDDR4.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
PHY_898, PHY_919 would require to configure PHY LP4 boot
pll control and ca for lpddr4.
So, configure the same in pctl_cfg for LPDDR4.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
It is possible in lpddr4 dram, where both the channels would
start at same time with ZQ Cal Start. If it uses ZQ Call start
then it will use RZQ.
For example LPDDR4 366 Dual-Die, Quad-Channel Package, RZQ maybe
connect to both channel. If ZQ Cal Start at the same time,
it will use the same RZQ.
It is not a problem of using RZQ in both the channels, but can not
use at the same time.
So, to avoid this, we have an option of dram tINIT3 value for
increasing the frequency for channel 1.
This patch increase the available tINIT3 with existing running
dram frequency.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
lpddr4 has PLL bypass mode during phy initialization phase,
which does all pll configurations.
So no need to wait explicitly during pctl config.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
mode_sel assignment is based on dram type.
In phy_io_config, already have vref setting based
on the dram type, so move this mode_sel assignment
on vref setting area.
No functionality change.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add rank_mask based on the rank number for lpddr4.
This would keep the wdql data training loop based on the
desired rank mask value instead of looping for all values.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add rank_mask based on the rank number for lpddr4.
This would keep the ca data training loop based on the
desired rank mask value instead of looping for all values.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Supporting LPDDR4 code support in RK3399 would increases
the size of SPL/TPL.
So add kconfig entry for RK3399 LPDDR4 code so-that
the boards have LPDDR4 can enable them via defconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Some dramtypes like lpddr4 initialization would required to
configure phy IO even after pctl_cfg and after set_ds_odt.
For those cases the set_ds_odt would be an initial call to
setup the phy.
To satisfy all the cases, trigger phy IO from set_ds_odt.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add DdrMode structure with associated bit fields.
These would help to reconfigure sdram capabilities during
lpddr4 setup related configs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add DdrTimingC0 structure with associated bit fields.
These would help to reconfigure sdram capabilities during
lpddr4 setup related configs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add dram config macro for handling ddr version number.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
cs0_row, cs1_row and cs1_col needs more bits to show its
correct value, update to make use of both sys_reg2,
sys_reg3.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash similar patches into one patch)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
Use dram config variable name as sys_reg2 instead of sys_reg
since the final variable value is to written into a pmugrf
register named as sys_reg2.
This reflect the both variable and associated register
names are same and also help to add next sys_reg's to
add it in future.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add simplified and meaningful macro for all setting.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash the similar patches into 1 patch)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
This would help to debug the sdram base parameters while
debugging existing chip or while supporting new sdram type.
It require explicit enablement of CONFIG_RAM_ROCKCHIP_DEBUG
for showing the debug prints.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Right now the rk3399 sdram driver assume that the board
has configured with 2 channels, so any possibility to
enable single channel on the same driver will encounter
channel #1 data training failure.
Log:
U-Boot TPL board init
sdram_init: data training failed
rk3399_dmc_init DRAM init failed -5
So, add an algorithm that can capable to compute the active
or configured rank with associated channel like
a) do rank loop to compute the active rank, with associated
channel numbers
b) then, succeed the data training only for configured channel
c) preserve the rank for given channel
d) do channel loop for setting the active channel
e) if given rank is zero or inactive on the specific channel,
clear the timings for the associated channel
f) finally, return error if number of channels is zero
Tested in NanoPI-NEO4 since it support single channel sdram
configuration.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(add PI_READ_GATE_TRAINING for LPDDR3 to support rk3399-evb case)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
This patch fixes not enabled uart2 (and hence serial console) on i.MX53
devices. After following commit 1d255904c3 ("ARM: dts: imx: imx53:
Synchronize iMX53 DT with Linux") from the uart2 compatible the
'fsl,imx7d-uart' has been removed (which was correct).
However, the root cause of the problem was the commit 98d62e618b ("arm:
imx: add i.MX53 Beckhoff CX9020 Embedded PC") which introduced this
compatible.
Moreover, without this patch all i.MX53 UARTs are not usable as neither
'fsl,imx53-uart' nor 'fsl,imx21-uart' are in compatible IDs in
drivers/serial/serial_mxc.c file.
The fix is to add 'fsl,imx53-uart' and 'fsl,imx21-uart' as compatibles
for the aforementioned serial driver (those are also defined in the Linux
kernel).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
The DM_FLAG_PRE_RELOC shall be set unconditionally as this driver is going
to be re-used in both early SPL and U-Boot proper's pre-reloc.
For i.MX based devices it is crucial to have available the serial console
before relocation (otherwise the board may hand).
The device definition may be provided either via device tree description or
with U_BOOT_DEVICE(mxc_serial) definition. In the latter case the device
will not bind in U-Boot proper when DM_FLAG_PRE_RELOC is not set.
The !CONFIG_IS_ENABLED(OF_CONTROL) #if check was set as a "workaround" for
DM problem described in following commit 4687919684
("serial: Remove DM_FLAG_PRE_RELOC flag in various drivers").
Let's look on this check more thoroughly - we add this flag if the board
doesn't support OF_CONTROL. This is a bit strange as the serial_mxc.c can
be used with CONFIG_DM_SERIAL but without corresponding device tree
description (OF_CONTROL). In such case the aforementioned
U_BOOT_DEVICE(mxc_serial) definition is used.
Other boards/SoCs have this flag set unconditionally for serial driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add DM and DT probing support to iMX watchdog driver. This should
allow boards to move over to this driver, enable SYSRESET_WATCHDOG
to handle cpu_reset() if required.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Use CONFIG_IS_ENABLED(WDT) to permit use of WDT in SPL without DM,
while the full U-Boot can use rich DM/DT WDT driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Suniel Mahesh <sunil.m@techveda.org>
BD71837 and BD71847 is PMIC intended for powering single-core,
dual-core, and quad-core SoC’s such as NXP-i.MX 8M. BD71847
is used for example on NXP imx8mm EVK.
Add regulator driver for ROHM BD71837 and BD71847 PMICs.
BD71837 contains 8 bucks and 7 LDOS. BD71847 is reduced
version containing 6 bucks and 6 LDOs. Voltages for DVS
bucks (1-4 on BD71837, 1 and 2 on BD71847) can be adjusted
when regulators are enabled. For other bucks and LDOs we may
have over- or undershooting if voltage is adjusted when
regulator is enabled. Thus this is prevented by default.
BD718x7 has a quirk which may leave power output disabled
after reset if enable/disable state was controlled by SW.
Thus the SW control is only allowed for BD71837 bucks
3 and 4 by default. The impact of this limitation must be
evaluated board-by board and restrictions may need to be
modified. (Linux driver get's these limitations from DT and we
may want to implement same on u-Boot driver).
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The code responsible for setting proper values in the MUX registers
(in the mxs_pinctrl_set_state()) has been ported from Linux kernel
- SHA1: 17bb763e7eaf tag v5.1.11 from linux-stable.
As the pinctrl node in the imx28.dtsi file has gpio pins nodes as subnodes,
it was necessary to use 'dm_scan_fdt_dev()' (as a .bind method) to also
make them 'visible' by the DM's "gpio_mxs" driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
This patch adds support for DM/DTS in the mxs_gpio.c driver.
Information regarding per gpio controller pin number is passed via DTS.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The fec_mxc.c driver can be reused by i.MX28 when DM_ETH is enabled.
One only needs to add proper compatible and dependency on FEC_MXC in the
Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.
It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.
It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.
So, cmd_nandbcb implemented in arch/arm/mach-imx
BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.
On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks
for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.
Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
This patch provides code to implement the CCF clock tree in sandbox. It
uses all the introduced primitives; some generic ones are reused, some
sandbox specific were developed.
In that way (after introducing the real CCF tree in sandbox) the recently
added to clk-uclass.c: clk_get_by_id() and clk_get_parent_rate() are tested
in their natural work environment.
Usage (sandbox_defconfig and sandbox_flattree_defconfig):
./u-boot --fdt arch/sandbox/dts/test.dtb --command "ut dm clk_ccf"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The generic mux clock code for CCF requires reading the clock multiplexer
value from HW registers. As sandbox by design has readl() as no-op it was
necessary to provide this value in the other way.
The new field in the mux structure (accessible only when sandbox is run)
has been introduced for this purpose.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The generic divider clock code for CCF requires reading the divider value
from HW registers. As sandbox by design has readl() as no-op it was
necessary to provide this value in the other way.
The new field in the divider structure (accessible only when sandbox is
run) has been introduced for this purpose.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
If the CLK_GET_RATE_NOCACHE flag is set - the clk_get_parent_rate()
provides recalculated clock value without considering the cache setting.
This may be necessary for some clocks tightly coupled with power domains
(i.e. imx8), and prevents from reading invalid cached values.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch brings the files from Linux kernel (linux-stable/linux-5.1.y
SHA1: 5752b50477da)to provide clocks support as it is used on the Linux
kernel with Common Clock Framework [CCF] setup.
The directory structure has been preserved. The ported code only supports
reading information from PLL, MUX, Divider, etc and enabling/disabling
the clocks USDHCx/ECSPIx depending on used bus. Moreover, it is agnostic
to the alias numbering as the information about the clock is read from the
device tree.
One needs to pay attention to the comments indicating necessary for U-Boot's
driver model changes.
If needed, the code can be extended to support the "set" part of the clock
management.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit adds the clk_get_by_id() function, which is responsible
for getting the udevice with matching clk->id. Such approach allows
re-usage of inherit DM list relationship for the same class (UCLASS_CLK).
As a result - we don't need any other external list - it is just enough
to look for UCLASS_CLK related udevices.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This commit adds the clk_get_parent_rate() function, which is responsible
for getting the rate of parent clock.
Unfortunately, u-boot's DM support for getting parent is different
(the parent relationship is in udevice) than the one in Common Clock
Framework [CCF] in Linux.
To alleviate this problem - the clk_get_parent_rate() function has been
introduced to clk-uclass.c.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This commit adds the clk_get_parent() function, which is responsible
for getting the parent's struct clock pointer.
U-Boot's DM support for getting parent is different (the parent
relationship is in udevice) than the one in Common Clock Framework [CCF]
in Linux. To obtain the pointer to struct clk of parent the
pdev->uclass_priv field is read via dev_get_clk_ptr() wrapper.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Up till now the fixed rate clock ('osc') has been added to UCLASS_CLK
without declaring struct clk. As a result it was only accessible by
iterating the udevice's uclass list.
This is a problem for clock code, which operates on pointers to struct
clk (like clk_get_rate()), not udevices.
After this change struct clk is accessible from udevice and udevice from
struct clk.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This check requires the struct clk passed to .get_rate() to be always
cleared out as any clock with valid ID causes -EINVAL return value.
The return code of fixed clocks shall always be returned.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The GEMGXL clock driver is now directly part of Cadence MACB
ethernet driver in upstream Linux kernel. There is no separate
GEMGXL clock driver in upstream Linux kernel hence we drop
GEMGXL clock driver from U-Boot as well.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The DT bindings of SiFive clock driver in upstream Linux has
changes. As-per latest DT bindings, the clock driver takes two
parent clocks and compatible string has also changed.
This patch sync-up SiFive clock driver implementation as-per
upstream Linux so that we now use latest DT bindings.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The location and license header of DT bindings header for SiFive
clock driver has changed in upstream Linux hence this patch.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that SiFive clock driver is merged in upstream Linux, we
sync-up WRPLL library used by SiFive clock driver with upstream
Linux sources.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To match SiFive clock driver with latest Linux, we factor-out PLL
library as separate module under drivers/clk/analogbits.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add stride computation for the sdram which support
single channel a
This configuration available in NanoPi NEO4 and the
same can work with existing rk3399-sdram-ddr3-1866.dtsi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
stride value from sdram timings can be computed dynamically
based on the determined capacity for the given channel.
Right now these stride values are taken as part of sdram timings
via dtsi, but it possible to use same timings dtsi for given
frequency even though the configured board sdram do support
single channel with different size by dynamically detect the
stride value.
Example, NanoPi NEO4 do have DDR3-1866, but with single channel
and 1GB size with dynamic stride detection it is possible to
use existing rk3399-sdram-ddr3-1866.dtsi whose stride,
number of channels and capacity it support is d efferent.
So, add initial support to calculate the stride value for
2 channels sdram, which is available by default on existing
boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add code to print the channel stride, this would help to
print the stride of associated channel.
Here is sample print on LPDDR4, 50MHz.
256B stride
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add code to get the channel capacity, this would help to
print the capacity of specific channel.
Here is sample print on LPDDR4, 50MHz channel 0
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add sdram ddr info print support, this would help to
observe the sdram base parameters.
Here is sample print on LPDDR4, 50MHz channel 0
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add sdram driver to handle debug across rockchip SoCs.
This would help to improve code debugging feature for
sdram drivers in rockchip family, whoever wants to
debug the driver should call these core debug code on
their respective platform sdram drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Right now sdram drivers in rockchip SoC are built based
on the SoC configs which may not be an adequate solutions
while adding common or debug driver.
So, add meaningful Kconfig options start with rk3399.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add support for pctl start for both channel 0, 1 control
and phy registers.
This would also handle pwrup_srefresh_exit init based
on the channel number.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add pwrup_srefresh_exit to be part of dram_info so-that
the it can help to support pwrup_srefresh_exit in individual
channels while starting pctl in future.
No functionality change.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add support for phy pctrl reset support for both channel 0, 1.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add rank_mask based on the rank number, this would keep
the wdql data training loop based on the desired rank mask
value instead of looping for all values.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add rank_mask based on the rank number, this would keep
the ca data training loop based on the desired rank mask
value instead of looping for all values.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Clear the PI_175 interrupts before processing actual
data training in all relevant calls.
This would help to clear interrupt from previous training.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
data trainings calls like ca, wl, rg, rl, wdql have proper
return types with -EIO and the return type missed to handle
in data_training function.
This patch, add proper return type checks along with useful
debug statement on each data training calls.
Incidentally this would help to prevent the sdram initialization
hang for single channel dram and when the code is trying to
initialize second channel with proper return type of relevant
data training call might failed.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
- CHECK: spaces preferred around that '*'
- CHECK: spaces preferred around that '/'
- CHECK: space preferred before that '|'
- WARNING: macros should not use a trailing semicolon
- CHECK: Unnecessary parentheses around 'fbdiv <= min_fbdiv'
- CHECK: Unnecessary parentheses around 'parent->id == SCLK_MAC'
- CHECK: Unnecessary parentheses around 'parent->dev == clk->dev'
- WARNING: line over 80 characters
- CHECK: Prefer kernel type 'u8' over 'uint8_t'
- Add proper macro definitions arrangements
Note: there are still line over 80 characters and other warnings but
fixing those making code look unreadable, so I kept it as it is.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Group common ddr attributes like
- rank
- col
- bk
- bw
- dbw
- row_3_4
- cs0_row
- cs1_row
- ddrconfig
into a common cap_info structure for more code readability and extend
if possible based on the new features.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Order tsel* variable declarations and assignment in proper
and meaningful way.
No functionality change.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Rename ca_tsel_wr_select_p to tsel_wr_select_ca_p based
on the bsp code.
No functionality change.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Rename ca_tsel_wr_select_n to tsel_wr_select_ca_n based
on the bsp code.
No functionality change.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Rename tsel_wr_select_p to tsel_wr_select_dq_p based
on the bsp code.
No functionality change.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Rename tsel_wr_select_n to tsel_wr_select_dq_n based
on the bsp code.
No functionality change.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add proper return type handling of pctl_cfg with
meaningful print statement.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Rename variable name of struct rk3399_sdram_params
from sdram_params with params for more code readability.
No functionality change.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
- Add proper spaces in data training, rk3399_dmc_init, pctl_cfg
- Order include files
- Move macro after include files
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Fix checkpatch warninigs on sdram_rk3399.c like
- Avoid CamelCase
- Unnecessary parentheses
- Alignment should match open parenthesis
- multiple blank lines
- misspelled
- spaces preferred around that '>>'
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Remove RK3399 compatible strings as this driver is no longer
used on that SoC.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Configure USB2 PHY register based on "phy_type" property and
handle all the quirks that are relevant for Rockchip RK3399 SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add compatible string for RK3399 and enable it by default on
Rockchip platforms with USB3 support.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The "simple" OF glue layer for the Designware USB3 core enables
all refernced clocks. These need to be need to be implemented
otherwise the driver fails to probe. A dummy implementation
that simply returns success is sufficient since the RK3399 comes
out of reset with all clock gates open.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The designware eth driver registers an mdio bus during probe, but if no
PHY is found, this bus is never removed although probe failes and the
driver is shown as not probed in the dm tree.
This later leads to errors when e.g. the mii or mdio commands try to
use available mdio buses because the mdio bus is still registered but
all corresponding data structures are invalid because probe failed.
Fix this by unregistering the mdio bus on probe failure (just as it is
unregistered in the .remove callback, too).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a test using a makeshift MDIO MUX. The test is based on the existing
MDIO test. It uses the last emulated PHY register to verify MUX selection.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This 2nd register is used by the follow-up MDIO MUX test.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a class for MDIO MUXes, which control access to a series of
downstream child MDIOs.
MDIO MUX drivers are required to implement a select function used to switch
between child buses.
MUX children are registered as MDIO buses and they can be used just like
regular MDIOs.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current code fails to probe some C45 PHYs that also respond to C22 reads.
This is the case for PHYs like Aquantia AQR112, Marvell 88X2242 (as
previously posted on the u-boot list).
If the PHY ID reads all 0s just ignore it and try the next devad.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
adds AQR112 and AQR412 to the list of supported PHYs using existing AQR
code.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
barno was mistakely readed from the target structure,
resulting in undefined behavious depending on the previous memory
content. fix that.
Fixes: bb41333782 ("pci_ep: add pci endpoint sandbox driver")
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
[trini: Drop unused bar_idx]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some storage devices have multiple hw partitions and both address from
zero, for example eMMC.
However currently block cache invalidation only applies to block
write/erase.
This can cause a problem that data of current hw partition is cached
before switching to another hw partition. And the following read
operation of the latter hw partition will get wrong data when reading
from the addresses that have been cached previously.
To solve this problem, invalidate block cache after a successful
select_hwpart operation.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Drivers need to be able to enable regulators that may be implemented as
GPIO regulators. Example: fsl_esdhc enables the vqmmc supply which is
commonly implemented as a GPIO regulator in order to switch between I/O
voltage levels.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
In preparation of being able to enable/disable GPIO regulators, the
code that will be shared among the two kinds to regulators is factored
out into its own source files.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add an implementation of the ds3231 driver that uses the driver
model i2c APIs.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
mt25qu512a is rebranded after its spinoff from STM, so it is
different only in term of extended jedec ID, initial JEDEC id
is same as that of n25q512a.In order to avoid any confussion
with respect to name new entry is added.
This flash is tested for Single I/O mode on LS1046FRWY although
it also support QUAD I/O.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch adds SiFive SPI driver. The driver is 100% DM driver
and it determines input clock using clk framework.
The SiFive SPI block is found on SiFive FU540 SOC and is used to
access flash and MMC devices on SiFive Unleashed board.
This driver implementation is inspired from the Linux SiFive SPI
driver available in Linux-5.2 or higher and SiFive FSBL sources.
Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Most DM based SPI host controller drivers use SPI_XFER_BEGIN and
SPI_XFER_END flags to enable/disable slave chip select.
This patch extends MMC SPI driver to pass SPI_XFER_BEGIN flag when
MMC command is send at start and pass SPI_XFER_END flag using a
dummy transfer (of bitlen = 0) at the end of MMC command.
Suggested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Use readl_poll_timeout instead of explicit calculation
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
During QSPI reads, current is_controller_busy function sporadically
fails with -ETIMEDOUT due to fixed number of 5 test loops. Using
timer functions to wait 1000 us instead will fix this.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When slave drivers don't set the max_read_size, the spi-mem should directly
use data.nbytes and not limit to any size. But current logic will limit to
the max_write_size.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
K3 devices have I2C IP that is same as OMAP2+ family. Allow driver to be
compiled for ARCH_K3.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
We would like to use the driver even without power domains being
specified for cases such as during early boot when the required power
domains have already gotten enabled by the SoC's boot ROM and such
explicit initialization is not needed and possible.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a platform specific set_control_reg() callback to help switch to
UHS speed modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The HOST_CONTROL2 register is a part of SDHC v3.00 and not just specific
to arasan/zynq controllers. Add the same to sdhci.h.
Also create a common API to set UHS timings in HOST_CONTROL2.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support in the driver for handling phy specific registers.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The am654_sdhci driver needs to switch the clock off
before disabling its phy dll and needs to re-enable
the clock before enabling the phy again.
Therefore, make the sdhci_set_clock() function accessible
in the am654_sdhci driver.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add Support for masking some bits in the capabilities
register of a host controller.
Also remove the redundant readl() into caps1.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In device nodes with more than one entry in the reg property,
it is sometimes useful to regmap only of the entries. Add an
API regmap_init_mem_index() to facilitate this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The host controller works perfectly well without having to add any
quirks. Remove them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync the sdhci0 node from kernel. This changes the compatible that is
required to be there in the driver. Change the same for the SD card node
which is not yet supported in kernel. This also syncs the main_pmx0 node
as a side effect.
Also change the name of the driver to match the compatible in kernel.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The USB PHY used in the Allwinner H6 SoC has some pecularities (as usual),
which require a small addition to the USB PHY driver:
In this case the second PHY is PHY3, not PHY1, so we need to skip number
1 and 2 in the code. Just use the respective code from Linux for that.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To enable USB support in U-Boot, add the required clock and reset gates
to the H6 clock driver. Once enabled, the generic EHCI/OCHI drivers will
pick them up from there automatically.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 pin controller is not really special, at least not when
it comes to normal GPIO operation.
Add the H6 compatible strings to the list of recognised strings, to make
GPIOs work for H6 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Probably for no particular reason SUNXI_GPIO was still defined the "old
way", in header files only.
Introduce SUNXI_GPIO to the Kconfig file in drivers/gpio to remove
another line from our dreadful config_whitelist.txt.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Macb can be used with Xilinx PCS/PMA PHY in fpga which is a 1000-baseX
phy(lpa 0x41e0). This patch adds checks for LPA_1000XFULL and
LPA_1000XHALF bits.
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If macb is gem and is gigabit capable, lpa value is not read from
the right register(MII_LPA) and is read from MII_STAT1000. This patch
fixes reading of the lpa value.
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add new driver for the TI AM65x SoC Gigabit Ethernet Switch subsystem (CPSW
NUSS). It has two ports and provides Ethernet packet communication for the
device and can be configured as an Ethernet switch. CPSW NUSS features: the
Reduced Gigabit Media Independent Interface (RGMII), Reduced Media
Independent Interface (RMII), and the Management Data Input/Output (MDIO)
interface for physical layer device (PHY) management. The TI AM65x SoC has
integrated two-port Gigabit Ethernet Switch subsystem into device MCU
domain named MCU_CPSW0. One Ethernet port (port 1) with selectable RGMII
and RMII interfaces and an internal Communications Port Programming
Interface (CPPI) port (Host port 0).
Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX
channels and on RX channels operating by TI am654 NAVSS Unified DMA
Peripheral Root Complex (UDMA-P) controller.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use phys_addr_t for mdio_base address to avoid build
warnings on arm64 and dra7. Cast it to uintprt_t before
assigning to regs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch is to use block layer to read from mmc in cortina
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Because all MSCC SoC use the same MDIO bus, put the implementation in
one common file(mscc_miim) and make all the other MSCC network drivers to
use these functions.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
A very simple test for DM_MDIO, mimicks a register write/read through the
sandbox bus to a dummy PHY.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
stand-alone devices. Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When serdes configuration was written in hardware there was a delay
of 100ms to be sure that configuration was written. But the delay is not
needed because already the function serdes_write it is checking that the
operation finished.
Therefore remove the mdelay. This improves the speed of configuring the
network driver.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The code block reading the DT property for the clock output control was
before the phy's DT node pointer was set, so it could never work. Move
it after the node pointer is set.
Also store the unsigned 32-bit property into an unsigned value, not a
signed value, as the former will cause a problem if value overflows.
For instance, if one were to add 0xffffffff as a code to mean the clock
output should be turned off.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Janine Hagemann <j.hagemann@phytec.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When not using DM_ETH, these PHY settings are programmed with default
values hardcoded into the driver. When using DM_ETH, they should come
from the device tree. However, if the device tree does not have the
properties, the driver will silent use -1. Which is entirely out of
range, programs nonsense into the PHY's registers, and does not work.
Change this to use the same defaults as non-DM_ETH if the device tree is
lacking the properties.
As an alternative, the kernel driver for the phy will display an error
message and fail if the device tree is lacking.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Janine Hagemann <j.hagemann@phytec.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- mmc spi driver model support
- drop mmc_spi command
- enhanced Strobe mmc HS400 support
- minor mmc bug/fixes and optimization
- omap hsmmc and mvbeu update
- sdhci card detect support
Flash system partition with fastboot will earse the partition firstly
The 600ms timeout will fail on some SD Card. Enlarge it to 5s to make
it works for most of sdcard
Cc: guoyin.chen <guoyin.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement set_enhanced_strobe hook for fsl_esdhc_imx,
,in esdhc_set_timing and esdhc_change_pinstate, also handle HS400_ES.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
eMMC 5.1+ supports HS400 Enhances Strobe mode without the need for
tuning procedure.
The flow is as following:
- set HS_TIMIMG (Highspeed)
- Host change freq to <= 52Mhz
- set the bus width to Enhanced strobe and DDR8Bit(CMD6),
EXT_CSD[183] = 0x86 instead of 0x80
- set HS_TIMING to 0x3 (HS400)
- Host change freq to <= 200Mhz
- Host select HS400 enhanced strobe complete
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Should use CONFIG_IS_ENABLED not IS_ENABLED for clock and regulator drivers,
CONFIG_IS_ENABLED will check the CONFIG_SPL_CLK and CONFIG_SPL_DM_REGULATOR
when building SPL.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch rewrites MMC SPI driver using U-Boot DM
framework and get it's working on SiFive Unleashed
board.
Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The MMC mode and width are fixed for MMC SPI host hence we skip
sd_select_mode_and_width() and mmc_select_mode_and_width() for
MMC SPI host.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Accessing the boot partition had been error prone with HS200 and HS400 and
was disabled. The driver first switched to a lesser mode and then switched
the partition access. It was mostly due to a bad handling of the switch and
has been fixed, so let's remove this 'feature'
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The switch operation can sometimes make the bus unreliable, in that case
the send_status parameter should be false to indicate not to poll using
CMD13. If polling on dat0 is possible, we should use it to detect the end
of the operation.
At the end of the operation it is safe to use CMD13 to get the status of
the card. It is important to do so because the operation may have failed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The e-MMC spec allows the e-MMC to specify a timeout for the partition
switch command. It can take up to 2550 ms. There is no lower limit to this
value in the spec, but do as the the linux driver does and force it to be
at least 300ms.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Starting with rev 4.5, the eMMC can define a generic timeout for the
SWITCH command.
Following Linux Kernel code, the timeout also changed from 1000 -> 500
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Using the DAT0 line as a rdy/busy line is an alternative to reading the
status register of the card. It especially useful in situation where the
bus is not in a good shape, like when modes are switched.
This is also how the linux driver behaves.
Note of warning: As per the specification, while polling on DAT0 the CLK
must not turned off: "[...] Without a clock edge the Device (unless
previously disconnected by a deselect command (CMD7)) will force the DAT0
line down, forever. [...]"
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
mmc_send_status() is currently used to poll the card until it is ready, not
actually returning the status of the card.
Make it return the status and add another function to poll the card.
Also remove the 'extern' declaration in the mmc-private.h header to comply
with the coding standard.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This reverts commit 318a7a576b.
The last and only user of this callback had been the omap_hsmmc driver.
It is not used anymore. Removing the callback.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This is not required. The MMC core sends CMD0 right after the
initialization and it serves the same purpose.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
It sometimes happen that the PSTATE register does not indicate that the
bus is ready when it really is. This usually happens after a mode switch.
In that case it makes sense to reset the FSM handling the CMD and DATA
Also reset the FSMs if the STATE register cannot be cleared. This also
sometimes happens after a mode switch.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The response type of CMD25 is R1 instead of R1b.
Signed-off-by: Akio Hirayama <hirayama.akio@socionext.com>
[masahiro: add log ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Card detect function implemented for SDHCI framework.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch reads cd-gpio property from devicetree
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch reads card detect properties from device tree &
added mmc capability macros in mmc.h.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fixed regulators don't have a set_value method. Therefore, trying to
set their value will always return -ENOSYS.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
add gpio-hog support. GPIO hogging is a mechanism
providing automatic GPIO request and configuration
as part of the gpio-controller's driver probe function.
for more infos see:
doc/device-tree-bindings/gpio/gpio.txt
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Michal Simek <michal.simek@xilinx.com> (zcu102)
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
The TI Davinci (da850/l138/am1808) use pinctrl-single,bits for
pinmuxing peripherals. This patch allosw the pinctrl-single
driver to parse the pinctrl-single,bits options and correctly
setup devices.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add SPL_DM_REGULATOR configs for palmas/lp873x/lp87565. These were missing
and the Makefile already assumes them to be defined. Add the corresponding
SPL config options. This enables the regulator support in SPL.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Add SPL_PMIC configs for palmas/lp873x/lp87565. These were missing
and the Makefile already assumes them to be defined. Add the corresponding
SPL config options. This enables the pmics in SPL.
Signed-off-by: Keerthy <j-keerthy@ti.com>
This commit addresses the following warning, when _NOT_ USB_MUSB_HOST:
[...]
CC drivers/usb/gadget/f_mass_storage.o
CC drivers/usb/musb-new/omap2430.o
CC drivers/usb/gadget/f_fastboot.o
CC env/common.o
CC env/env.o
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c: In function ‘omap2430_musb_probe’:
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c:239:6: warning: assignment to ‘int’ from ‘struct musb *’ makes integer from pointer without a cast [-Wint-conversion]
ret = musb_register(&platdata->plat,
^
LD drivers/usb/host/built-in.o
CC drivers/usb/gadget/f_sdp.o
CC fs/ext4/ext4fs.o
[...]
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
add m41t11 support in ds1307 driver. changes:
- add compatible string for m41t11
- check if RTC clock is running, if not
enable the clock
Signed-off-by: Heiko Schocher <hs@denx.de>
When MMC_TINY is enabled, support for only one MMC device
is provided. Boards that register more than one device,
will just write over mmc_static keeping only the last one
registered.
This commit prevents this, keeping only the first MMC
device created. A debug warning message is added, if nothing
else, as a hint/documentation for developers.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
The SPL_MMC_TINY implements feature-reduced MMC support
on SPL, and as such, it's more consistent and convenient
to find it as part of the SPL configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
`if (!strncmp(dev->name, name, strlen(name)))` might find out
the wrong device, it might find out `dram_pll_ref_sel`, when name is
`dram_pll`. So use strcmp to avoid such issue.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the uclass_first_device_check and uclass_next_device_check functions
instead of uclass_first_device and uclass_next_device in pci_init. This
ensures that all PCI devices are tried to be probed. Currently if a
device fails to probe, the enumeration stops and the devices which come
after the failed device are not probed.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: VlaoMao <vlaomao@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
As compatible string "st,stm32-gpio" is no more used, .ofmatch
callback becomes useless, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Update .bind callback in order to bind all pinctrl subnodes
with "gpio-controller" property to gpio_stm32 driver.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
As this driver is used on stm32f4/f7/h7 and stm32mp1
SoCs, rename it with a more generic name.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
drivers/spi/stm32_spi.c: In function 'stm32_spi_write_txfifo':
drivers/spi/stm32_spi.c:116:20: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (priv->tx_len >= sizeof(u32) &&
^~
drivers/spi/stm32_spi.c:122:27: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
} else if (priv->tx_len >= sizeof(u16) &&
^~
drivers/spi/stm32_spi.c: In function 'stm32_spi_read_rxfifo':
drivers/spi/stm32_spi.c:150:21: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
(priv->rx_len >= sizeof(u32) || (sr & SPI_SR_RXWNE))) {
^~
drivers/spi/stm32_spi.c:156:21: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
(priv->rx_len >= sizeof(u16) ||
^~
drivers/core/simple-bus.c:15:12: warning: no previous prototype for 'simple_bus_translate' [-Wmissing-prototypes]
fdt_addr_t simple_bus_translate(struct udevice *dev, fdt_addr_t addr)
^~~~~~~~~~~~~~~~~~~~
drivers/spi/stm32_spi.c: In function 'stm32_spi_set_speed':
drivers/spi/stm32_spi.c:335:10: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
div > STM32_MBR_DIV_MAX)
^
drivers/spi/stm32_spi.c:344:19: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if ((mbrdiv - 1) < 0)
^
drivers/spi/stm32_spi.c: In function 'stm32_spi_probe':
drivers/spi/stm32_spi.c:531:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
for (i = 0; i < ARRAY_SIZE(priv->cs_gpios); i++) {
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves warnings detected by setting W=1 when building.
Warnings type detected:
- [-Wtype-limits]
- [-Wsign-compare]
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves warnings detected by setting W=1 when building.
Warnings type detected:
- [-Wsign-compare]
- [-Wtype-limits]
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (*idx < 0)
^
drivers/pinctrl/pinctrl_stm32.c: At top level:
warning: no previous prototype for 'stm32_pinctrl_probe' [-Wmissing-prototypes]
int stm32_pinctrl_probe(struct udevice *dev)
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Patrice CHOTARD <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
drivers/ram/stm32mp1/stm32mp1_ram.c: In function 'stm32mp1_ddr_clk_enable':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
for (idx = 0; idx < ARRAY_SIZE(clkname); idx++) {
^
drivers/ram/stm32mp1/stm32mp1_ram.c: In function 'stm32mp1_ddr_setup':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
for (idx = 0; idx < ARRAY_SIZE(param); idx++) {
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
warning: no previous prototype for 'fuse_read' [-Wmissing-prototypes]
int fuse_read(u32 bank, u32 word, u32 *val)
^~~~~~~~~
CC cmd/sf.o
warning: no previous prototype for 'fuse_prog' [-Wmissing-prototypes]
int fuse_prog(u32 bank, u32 word, u32 val)
^~~~~~~~~
warning: no previous prototype for 'fuse_sense' [-Wmissing-prototypes]
int fuse_sense(u32 bank, u32 word, u32 *val)
^~~~~~~~~~
warning: no previous prototype for 'fuse_override' [-Wmissing-prototypes]
int fuse_override(u32 bank, u32 word, u32 val)
^~~~~~~~~~~~~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
drivers/power/regulator/stm32-vrefbuf.c: In function 'stm32_vrefbuf_set_value':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (uV == stm32_vrefbuf_voltages[i]) {
^~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
drivers/clk/clk_stm32mp1.c: In function 'stm32mp1_clk_get_parent':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
for (i = 0; i < ARRAY_SIZE(stm32mp1_clks); i++)
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
drivers/i2c/stm32f7_i2c.c: In function 'stm32_i2c_compute_solutions':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (scldel < scldel_min)
^
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (((sdadel >= sdadel_min) &&
^~
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
(sdadel <= sdadel_max)) &&
^~
drivers/i2c/stm32f7_i2c.c: In function 'stm32_i2c_choose_solution':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (clk_error < clk_error_prev) {
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
drivers/gpio/stm32_gpio.c: In function 'stm32_offset_to_index':
: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (idx == offset)
^~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
drivers/adc/stm32-adc-core.c: In function 'stm32h7_adc_clk_sel':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
for (i = 0; i < ARRAY_SIZE(stm32h7_adc_ckmodes_spec); i++) {
^
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
for (i = 0; i < ARRAY_SIZE(stm32h7_adc_ckmodes_spec); i++) {
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
This patch solves the following warnings:
drivers/adc/stm32-adc.c: In function 'stm32_adc_chan_of_init':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (num_channels > adc->cfg->max_channels) {
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
This patch solves warnings detected by setting W=1 when building.
Warnings type detected:
- [-Wmissing-prototypes]
- [-Wimplicit-fallthrough=]
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
drivers/serial/serial_stm32.c: In function 'stm32_serial_probe':
warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (plat->clock_rate < 0) {
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Adds support for SYSRESET_POWER_OFF = PMIC power off used by command
power off and introduced by commit 751fed426f ("sysreset: Add a way
to find the last reset").
The driver use SYSRESET_POWER for the PMIC-level power cycle, with restart.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The new type sysreset 'POWER_OFF', introduced by
commit 751fed426f ("sysreset: Add a way to find the last reset")
is only supported for "syscon-poweroff" compatible.
For details see Linux binding:
./Documentation/devicetree/bindings/power/reset/syscon-poweroff.txt
This patch removes the support of POWER_OFF for "syscon-reboot"
and keeps only the COLD reset (for command reset support)
and it introduces the compatible "syscon-poweroff"
for the POWER_OFF case.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl0nbDoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZcBQgAn+ojgq/hD89bihuhz2oEe6rhzHB9OkcC
sHrVL8Jbmby/BuzISGe4oeeM5yVygBVtUiN/72JiiAHLmykqc4CpRjNvgOOAgKCy
Ml8UyiBNNVNfrD6f9PxAKvPZf6S0gfLnomGOQ/psdEojpY5AvQxQ36D+QFZ0AMP5
67/xjSfN9bNPw8UbgE/VhJ+WFbU948BP2EBt6+NBAtv7HW4AX9vT0famJfWEjwq8
ftmcFOSNGgYcDQ5BwQWX1sFhnwb9XSfurlQsVYBsFA4cx4gj0DfUm1Ugr4wDD+lo
91P+76hSBQ+mHp1HJ90WMd2vAaElG7/SoaicXo9pW6Rc7WIgTjk7gg==
=SdZy
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-9jul19-take2' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
- Sandbox improvements including .dts refactor
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
- SPL SATA enhancements to allow booting from RAW SATA device
needed for Clearfog (Baruch)
- Enable SATA booting on Clearfog (Baruch)
- Misc changes to Turris Omnia (Marek)
- Enable CMD_BOOTZ and increase SYS_BOOTM_LEN on crs305-1g-4s
(Luka)
- Enable FIT support for db-xc3-24g4xg (Chris)
- Enable DM_SPI on Keymile Kirkwood board with necessary changes
for this (Pascal)
- Set 38x and 39x AVS on lower frequency (Baruch)
- import DT updates from Linux
- add UniPhier SPI controller driver
- make U-Boot image for 64bit SoCs position independent
- tidy up various init code for next generation SoCs
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=X9wS
-----END PGP SIGNATURE-----
Merge tag 'uniphier-v2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2019.10
- import DT updates from Linux
- add UniPhier SPI controller driver
- make U-Boot image for 64bit SoCs position independent
- tidy up various init code for next generation SoCs
- misc cleanups
Add TI TCA9539 compatible string for yet another I2C GPIO expander.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The TPM specification says that the EXPECT_DATA bit is not valid until
the VALID bit is set. Wait for that bit to be set. Fixes problems with
Ifineon SPI TPM.
Signed-off-by: Roman Kapl <rka@sysgo.com>
Add a dummy PCI endpoint for sandbox.
Supporting only a single function, it allows setting
and reading header configuration.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Cadence PCIe endpoint driver supporting configuration
of header, bars and MSI for device.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce new UCLASS_PCI_EP class for handling PCI endpoint
devices, allowing to set various attributes of the PCI endpoint
device, such as:
* configuration space header
* BAR definitions
* outband memory mapping
* start/stop PCI link
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
KM Kirkwood boards now implement the driver model for its SPI flash
interface. Therefore, the old board specific claim and release functions
can be deleted. The preprocessor definition CONFIG_SYS_KW_SPI_MPP is yet
unused as well. All its appearances and dependencies are removed in the
kirkwood_spi driver, header files and finally the configuration whitelist.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The weak functions, known from the legacy code, are added to the DM part
as well. For this purpose, the release operation first needs to be
implemented. KM Kirkwood boards will overwrite those weak functions to
change the MPP configuration when claiming/releasing the bus, because the
hardware pins are shared between the SPI NOR and NAND devices.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Adds dm_pci_flr API that issues a Function Level reset on a PCI-e function,
if FLR is supported.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This test is built on top of the existing swap_case driver. It adds EA
capability structure support to swap_case and uses that to map BARs.
BAR1 works as it used to, swapping upper/lower case. BARs 2,4 map to a
couple of magic values.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Makes dm_pci_map_bar API available for integrated PCI devices that
support Enhanced Allocation instead of the original PCI BAR mechanism.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This add missing parts for previous commit 06f94461a9
("fdt: Allow indicating a node is for U-Boot proper only")
At present it is not possible to specify that a node should be used before
relocation (in U-Boot proper) without it also ending up in SPL and TPL
device trees. Add a new "u-boot,dm-pre-proper" boolean property for this.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default LPUART driver with compatible string "fsl,ls1021a-lpuart"
support big-endian mode.On NXP SoC like LS1028A LPUART IP is
little-endian,Added support to Fetch LPUART IP Endianness from lpuart
device-tree node.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In general we should avoid calling malloc() and free() repeatedly in
U-Boot lest we turn it into tianocore. In SPL this can make SPI flash
unusable since free() is often a nop and allocation space is limited.
In any case, these seems no need for malloc() since the number of bytes
is very small, perhaps less than 8.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: d13f5b254a (spi: Extend the core to ease integration of SPI
memory controllers)
Generally block devices are not enabled in TPL, but in case they are,
add a Kconfig option for the block cache. This allows the setting (default
off) to be found with CONFIG_IS_ENABLED().
Signed-off-by: Simon Glass <sjg@chromium.org>
Since the SPI nor conversion, 'sf probe' does not work on sandbox. Fix
this by using the expected compatible string in the flash node.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: cd35365762 (mtd: sf_probe: remove spi-flash compatible)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdJEZEAAoJEB6zHgIOrC/I+LAH/jUDQpF5I68h0ZFGm3xoyGhm
3CSv8viOm/kL+GLubjnv4cwAp8N8VRpeJekz0Jt1Xp8C6OIgtnJ2Fln72KD+Z0IC
Rq7ByRS16iq4b6IUDRZObE4Jzxmf7rXU3jr0+/vd/en7kxVlvA9+Gsffs3OTGxC7
z9PysRZPBMH/smIPXdEQxYifnbpDG4fmfGcUWKrYfkB0Kq6Ep98Ia/gXNCY8XJ/A
sbNQGjJWJZWXS/TDetcC2VikssJ+yNFF34uzV+HD5Y3DW6ywLhuoDOz1pg8RR36i
YjcTCQz8lL/UVaUzrGUgPVAC3gdKY6J26GtV3vZavxBcmtGf0FhVtXO/tZc9AsY=
=6G45
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features and fixes for 2019.10 cycle
This includes the Atmel QSPI driver and support for the at91 boards.
This is the port of the driver from Linux, mostly done by Tudor Ambarus.
The previous pcf2127 RTC chip could not read and set the correct time.
When reading the data of internal registers, the read address was the
value of register plus 1. This is because this chip requires the host
to send a stop signal after setting the register address and before
reading the register data.
This patch sets the register address using dm_i2c_write and reads
the register data using the original dm_i2c_xfer in order to generate
a stop signal after the register address is set, and fixes the bug of
the original read and write time.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Backport the driver from linux v5.1-rc5 and adapt it for u-boot.
Tested on sama5d2_xplained Rev B with mx25l25635e spi-nor flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Prior to starting a new transfer, conditionally wait for bus to not
be busy.
Reinitialise controller as otherwise operation is not stable.
For reference, see linux kernel
commit 9656eeebf3f1 ("i2c: Revert i2c: xiic: Do not reset controller before every transfer")
hs: Fixed DOS line endings
added missing '\n'
Fixed git commit description style
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Comparison should be against the actual message length, not loop index.
len is used for stopping while loop, pos is position in message.
stop should be sent when entire message is sent, not when
len and pos meet.
hs: fixed DOS line endings
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Get clock rate from clock DM if CONFIG_CLK is enabled.
Otherwise, uses IC_CLK define.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Before calling __dw_i2c_set_bus_speed(),
the I2C could already be set as ether enable or disable,
we should restore the original setting instead of enable i2c anyway.
This patch fix a bug happened in init function:
__dw_i2c_init(){
/* Disable i2c */
...
__dw_i2c_set_bus_speed(i2c_base, NULL, speed);
writel(slaveaddr, &i2c_base->ic_sar);
/* Enable i2c */
}
In this case, enable i2c inside __dw_i2c_set_bus_speed() function
will cause ic_sar write fail.
Signed-off-by: Jun Chen <ptchentw@gmail.com>
This allows to silence ubi and ubispl individually.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
The motivation is to use the UBI atomic volume rename functionality to
allow double copy software updates on UBI. To that end the SPL is
configured to always load the same volume name (e.g. "u-boot"),
whereas a software updater always installs into the secondary volume
"u-boot_r". After successful installation, these two volume names are
switched.
This extension is protected by #ifdefs as it will somewhat slow down
loading of volumes by id. This is because the code needs to disable
the optimization of ignoring all volume ids which are not
to-be-loaded, since these can only be resolved after attaching.
This adds two vtbl related functions from Linux, which are taken from
the same kernel version as the current main U-Boot UBI code (Linux 4.2
64291f7db5bd8).
Signed-off-by: Hamish Guthrie <hamish.guthrie@kistler.com>
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
- drop CONFIG_ prefix from kconfig entry
- fix small compilation issue with CONFIG_UBI_SILENCE_MSG
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
set_pwm() will always fail with -ENOSYS if pwm_ops set_invert() is
not implemented, leaving the backlight dark. Fix this by returning
no error if set_invert() is not implemented and no polarity change
is requested.
Fixes: 57e7775413 ("video: backlight: Parse PWM polarity cell")
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
dwc3-generic has been broken since MISC uclass has been modified to scan DT
sub-nodes after bind.
Fixing it by a using the no-op uclass.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This uclass is intended for devices that do not need any features from the
uclass, including binding children.
This will typically be used by devices that are used to bind child devices
but do not use dm_scan_fdt_dev() to do it. That is for example the case of
several USB wrappers that have 2 child devices (1 for device and 1 for
host) but bind only one at a any given time.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The EHCI iMX6 driver is only partly converted to DT probing and
still uses a tremendous amount of hard-coded addresses. Worse,
the driver uses hard-coded SoC-model-specific base addresses, which
are derived from values protected by SoC-specific macros, hence the
driver is also compiled for a specific SoC model. Even worse, the
driver depends on specific sequential indexing of the controllers,
from which it derives offsets in the PHY and ANATOP register sets.
However, when the driver is probed from DT, the indexing is not
correct. In fact, each controller has index 0. This patch derives
the index for DT probing case from the controller base addresses,
which is not the way this should be done, however it is the least
intrusive approach, favorable this close to release.
The necessary steps to convert this driver fully to DT probing are
described inside the patch, however this should be done in the next
release and depends on iMX clock driver patches.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Add support for loading u-boot FIT images over the USB SDP protocol in
the SPL
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
[Various build fixes]
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Lukasz Majewski <lukma@denx.de>
The fsl_esdhc driver was for Freescale eSDHC on MPC83XX/MPC85XX
initially. The later QoriQ series PowerPC processors (which were
evolutions of MPC83XX/MPC85XX), QorIQ series ARM processors, and
i.MX series processors were using this driver for their eSDHCs too.
For the two series processors, the eSDHCs are becoming more and
more different. We should have split it into two drivers, like them
(sdhci-of-esdhc.c/sdhci-esdhc-imx.c) in linux kernel.
This patch is just to create a fsl_esdhc_imx driver which is a copy
of fsl_esdhc driver for i.MX processors. We will convert i.MX processors
to use fsl_esdhc_imx, and clean up the two drivers separately in the
future patches.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
The default timeout value had been left in order to leave some traces
about default setup of watchdog done by firmware.
For better understanding and compiler burden, replace it with a comment.
Suggested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
commit b7598a43f2 ("[PATCH] Avoid assigning PCI resources from
zero address") only moved the bus lower address to 0x1000 if the
given bus start address is zero. The comment said 0x1000 is a
reasonable starting value, hence we'd better apply the same
adjustment when the given bus start address is below 0x1000.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The driver was using milliseconds and programming it into a register
which takes ticks of the watchdog clock, which runs at 1MHz. This meant
we were off by 1000 with the desired value.
When 06985289d4 ("watchdog: Implement generic watchdog_reset()
version") was added the aspeed board would leave the watchdog running,
causing it to bite before u-boot was done.
Discovered by booting in qemu:
$ qemu-system-arm -M ast2500-evb -drive file=test.img,format=raw,if=mtd -nographic -no-reboot -d cpu_reset
U-Boot 2019.07-rc3-00091-g2253e40caef5 (Jun 06 2019 - 16:53:23 +0930)
Model: Aspeed BMC
DRAM: 496 MiB
WDT: Started with servicing (60s timeout)
MMC:
In: serial@1e784000
Out: serial@1e784000
Err: serial@1e784000
Watchdog timer expired.
Fixes: 06985289d4 ("watchdog: Implement generic watchdog_reset() version")
Signed-off-by: Joel Stanley <joel@jms.id.au>
