updates for the siemens am335x based boards:
- draco: add delay for DDR3 configuration
- change MTD partition layout and add a possibility
to redefine MTD layout in board header.
- move ubi support to common header file
- draco: improve dtb naming
- draco: set CONFIG_SYS_CBSIZE to 1024
- add generic env based led
Leds can now be defined in Environment
- add generic env based dfu button
Which gpio is used for the dfu button can be defined
through the Environment
- set MACH_TYPE only if defined
- draco: increase CPU freq to 300MHz
- Add time command to siemens am33xx boards
- DDR3: increase default tRFC
- draco: enable pullup for DFU and ERST pin
- change print format DDR3
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
This introduces the part start and part size sub-commands. The purpose of these
is to store the start block and size of a partition in a variable, given the
device and partition number.
This allows reading raw data that fits a single partition more easily.
For instance, this could be used to figure out the start block and size of a
kernel partition when a partition table is present, given the partition number.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Stephen Warren <swarren@nvidia.com>
[trini: Change "%lx" to LBAF]
Signed-off-by: Tom Rini <trini@konsulko.com>
The get_max_arm_speed() and get_max_dev_speed() used wrong register
fields to get the maximum speeds. This commit fixes the bug.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With the change to make sure that CONFIG_CMD_NET is enabled this board
no longer fits into the linker script:
powerpc-linux-ld.bfd: section .resetvec loaded at [fffffffc,ffffffff] overlaps section .u_boot_list loaded at [ffffff58,00000723]
powerpc-linux-ld.bfd: u-boot: section .resetvec lma 0xfffffffc adjusted to 0x724
powerpc-linux-ld.bfd: u-boot: section `.resetvec' can't be allocated in segment 0
LOAD: .data.init .text .rodata .reloc .data .u_boot_list .resetvec
powerpc-linux-ld.bfd: final link failed: File truncated
Drop CONFIG_SYS_LONGHELP to free up space.
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This allows using only one of either raw or fs mode for SPL mmc boot, without
the need to have provisions for the other. In particular, a device may have
U-Boot installed on a file system on the mmc, without ever needing to read
U-Boot from raw memory. Thus, there is no reason to provide a sector or
partition for raw mode. This allows this behaviour and still provides a robust
fallback mechanism in case provisions for both modes are defined.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
When building tools-only (or env) we need to be sure that we do use
<linux/kconfig.h> and do not use <generated/autoconf.h>. This will fix
problems such as running 'make defconfig' or 'make sandbox_config' and
then 'make tools-only'.
Based on the responses below to the thread add linux/kconfig.h higher in
the includes and drop the now unneeded autoconf.h lower down to ensure
the default environment is included correctly
http://lists.denx.de/pipermail/u-boot/2015-June/216849.html
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
We want to see if the requested start or total block count are
unaligned. We discard the whole numbers and only care about the
remainder. Update the code to use div_u64_rem here and add a comment.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
since we have now various processor-speeds it isn't useful anymore to
preinitialize kernels-delay loop.
Rather we want the kernel to calibrate it on every boot.
This wastes around 80ms boottime but is compatible to all CPU-speeds.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
in future we support yet another b&r am335x based board, where Timer 5 is
wired to backlight-driver.
So we introduce a new driver-type '2' to setup timer5 instead timer6.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently there is no default value for NETARGS if CONFIG_CMD_NET=y isn't set.
This results in build errors which was first discovered when trying to run
make env.
By defining a blank NETARGS these errors can be avoided.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Tested-by: Maxin B. John <maxin.john@enea.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since the tam3517 base board has a 16bit wide nand connected to
the gpmc, enable the prefetch mode, since that is now supported.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: pekon gupta <pekon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
commit c316f57 "mtd: OMAP: Enable GPMC prefetch mode" only enabled
prefetch mode for 8 bit nand access, this adds 16 bit as well.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
The prefech mode is a feature of the gpmc, not the ELM. An am3517
does not have an elm, but can do prefeches, so move the code out
of the CONFIG_NAND_OMAP_ELM ifdef.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
The MSI Primo 81 is an Allwinner A31s-based tablet on which the
OTG port is the only accessible USB interface. The existing
defconfig had VGA console on the LCD enabled, but was missing
keyboard support because the prerequisites for that (sunxi MUSB
support and AXP221 GPIO support) had not been available before.
All previously missing dependencies are available now, so this
patch enables keyboard support and its prerequisites in the
defconfig.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently on sun6i after a "reset" the prompt returns and the user can
even type stuff until the watchdog triggers and does the actual reset.
This is somewhat unexpected behavior for the "reset" command, this
commit adds an endless loop to wait for the watchdog to trigger so that
we do not return to the prompt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Remove the unused sunxi_musb_exit method, there is no code in u-boot
calling the exit method, and our implementation was broken as it did
not disable the clocks and asserted reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Fully resetting the controller is a too big hammer, and the musb_core will
then afterwards fail to communicate with any endpoints other then 0 as
too much state was cleared.
Instead report vbus low for 200ms which will effectively end the current
session without needing to do a full reset.
This fixes usb mass-storage devices no longer working after a "usb reset"
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
In the cases where we make use of environment in SPL we do not need
these defaults compiled in and available. These are taking up space
that in some cases now prevent linking, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
Vision Systems's Baltos is based on AM335x SoC
from Texas Instruments. This patch adds support
such Industrial PCs in mainline u-boot.
[ balbi@ti.com: updated original patch to current u-boot ]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Unlike OMAP5, EMIF PHY used in DRA7 will be left in unknown state after
warm reset, emif needs to be configured to bring it back to a known
state. So configure EMIF during warm reset.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now all the AVR32 boards have been converted into Generic Board.
Select it in Kconfig and clean up defines in header files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
On AM437x-GP Evm there is 2GB of DDR3 memory available as stated in
AM437x GP EVM HardwareUser's guide http://www.ti.com/lit/ug/spruhw7/spruhw7.pdf.
But MAX_RAM_BANK_SIZE is defined as 1GB.
Fixing MAX_RAM_BANK_SIZE to 2GB on AM43xx.
Reported-by: Shivasharan Nagalikar <shivasharan.nagalikar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The recent changes for hw leveling on am33xx were not intended for
DDR2 boards, only DDR3. Update emif_sdram_type to take a sdram_config
value to check against. This lets us pass in the value we would use to
configure, when we have not yet configured the board yet. In other cases
update the call to be as functional as before and check an already
programmed value in.
Tested-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
On AM57xx evm I2C5 is used to detect the LCD board by reading the
EEPROM present on the bus.
Enable i2c5 clocks to help that.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable booting from NAND on the am437xx-evm.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use the correct partition names from with the Device Tree blob
and the kernel is picked up. Also use partition name instead of
number for the root filesystem in the kernel boot arguments.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We almost always use UBIFS for user accessible NAND file systems and
the UBIFS file system might contain more than one volume within the
single NAND partition. The last NAND partition is therefore more
appropriately named as "NAND.file-system" instead of "NAND.rootfs"
The Linux kernel (as of v3.16) also uses "NAND.file-system" to name the
last NAND partition. This patch makes the partition name consistent
between u-boot and the kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Calxeda highbank SOC needs a custom sequence to bring up SATA links,
so override ahci_link_up with custom function to handle combophy setup.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Richard Gibbs
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andre Przywara <osp@andrep.de>
To support the Armada 38x, new values for the request-delay and the
response-timeout are needed. As the values already implemented in
this tool (for Kirkwood and Armada XP) don't seem to work here.
To make this more flexible, lets add make those 2 parameters
configurable via the cmdline. Here the new parameters:
-q <req-delay>: use specific request-delay
-s <resp-timeo>: use specific response-timeout
For the Marvell DB-88F6820 these values are known to work:
One board:
-q 2 -s 1
2nd board:
-q 5 -s 5
So this seems to be even board specific. But with this patch now
those values can be specified and tested via the cmdline.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Luka Perkov <luka.perkov@sartura.hr>
SMP-enabled Linux kernels read the CBAR register in CP15 to find
the address of the SCU registers. After remapping internal
registers, also update the CBAR so the kernel can find them.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
L2 cache may still be enabled by the BootROM. We need to first disable
it before enabling d-cache support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
If defined, the macro CONFIG_SYS_SPI_U_BOOT_OFFS allows a board
to specify the offset of the payload image into the kwb image
file. This value was being used to locate the image, but was not
used in the "header size" field of the main header. Move the
use of this macro into the function that returns the header size
so that the same value is used in all places.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Stefan Roese <sr@denx.de>
The AHCI driver currently waits 5s before timing out when sending a
data command to a drive. Some drives take upwards of 8s to respond to
the initial data command while they're spinning up. Increase the
data io timeout to 10s so that those drives can be found on initial
scsi scan.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
Enable full 48-bit LBA48 data reads by passing the upper word of the
LBA block pointer in bytes 9 and 10 of the FIS.
This allows uboot to load data from any arbitrary sector on a drive
with 2 or more TB of available data connected to an AHCI controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
[trini: Make use of CONFIG_SYS_64BIT_LBA in a few places to drop
warnings on platforms that don't enable that feature ]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Calxeda Midway part has A15 cores, which do not have the Highbank
A9's SCU used there for resetting the chip.
Add code to distinguish between the A9 and the A15 and invoke the
appropriate register writes to support the newer part.
Andre: rework detection of Highbank vs. Midway
Rob: fix Andre's reworked detection
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Now all manual mode configurations are done as part of
IO delay recalibration sequence, remove the hack done for
CPSW.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enabling IO delay recalibration sequence for DRA7 EVM.
UART and I2C are configured before IO delay recalibration sequence
as these are used earlier and safe to use.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
In addition to the regular mux configuration, certain pins of DRA7
require to have "manual mode" also programmed, when predefined
delay characteristics cannot be used for the interface.
struct iodelay_cfg_entry is introduced for populating
manual mode IO timings.
For configuring manual mode, along with the normal pad
configuration do the following steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1(Enable MANUAL_MODE macro along with mux)
- Populate A_DELAY, G_DELAY values that are specified in DATA MANUAL.
And pass the offset of the CFG_XXX register in iodelay_cfg_entry.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
On DRA7, in addition to the regular muxing of pins, an additional
hardware module called IODelay which is also expected to be
configured. This "IODelay" module has it's own register space that is
independent of the control module.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay recalibration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do muxing as part of IOdelay recalibration.
IODELAY recalibration sequence:
- Complete AVS voltage change on VDD_CORE_L
- Unlock IODLAY config registers.
- Perform IO delay calibration with predefined values.
- Isolate all the IOs
- Update the delay mechanism for each IO with new calibrated values.
- Configure PAD configuration registers
- De-isolate all the IOs.
- Relock IODELAY config registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
