The Beacon EmbeddedWorks kit is based on the R8A774B1 SoC also
known as the RZ/G2N.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi. It shares much of the same design as
the RZ/G2M dev kit.
Signed-off-by: Adam Ford <aford173@gmail.com>
These ops are missing at present which is not permitted. Add an empty
operation struct.
Note: If the uclass requires operations then the drivers should provide
them. Otherwise, checking for missing operations must be done in every
uclass operation, so it adds to code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Sync DTS from Linux kernel for all K3 platforms
- Add MMC higher speed nodes for AM65x, J721e, J7200
- Convert Nokia RX-51 to use CONFIG_DM_MMC
- Minor fixes for LEGO MINDSTORMS
This drops assigning bi_arch_number on LEGO MINDSTORMS EV3. This board
never had its own unique number and since we are using device tree,
we no longer need to pass an arch number to Linux.
Signed-off-by: David Lechner <david@lechnology.com>
This sets the serial# environmet variable instead of using ATAGs on
LEGO MINDSTORMS EV3.
Also fix some nomenclature while we are touching this code (Bluetooth
address is not the same as MAC address, EEPROM version is not the same
as board version).
Signed-off-by: David Lechner <david@lechnology.com>
Move twl4030_power_mmc_init() from board_mmc_power_init() to misc_init_r()
and disable CONFIG_SYS_MALLOC_F. Otherwise U-Boot cannot initialize MMC.
Also disable CONFIG_CMD_SLEEP CONFIG_DM_DEVICE_REMOVE CONFIG_MMC_VERBOSE to
free some space.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
addr was delcared as fdt_addr_t which is now a 64-bit address.
In a 32-bit build, this causes the following warning seen when
building ax25-ae350.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast addr with uintptr_t.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
This change extends previous commit 061c6d1b23 ("arm: mvebu: Espressobin:
Detect presence of emmc at runtime") and when emmc is not present then emmc
is removed from U-Boot DM and corresponding slot is disabled. Therefore on
Espressobin board without soldered emmc, state of emmc hw should be same as
if emmc was disabled in DTS.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
SATA and UART ClearFog imaages are not buildable as ENV_SECT_SIZE is not defined
set values for both possible targets
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card
support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0
port. It also has two GPIO headers which allows further peripherals to
be used.
The devicetree file is taken from v3 of the OrangePi Zero2 Linux
submission [1], which it's not yet merged.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632084.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This port is needed for communication with PMIC. SPL uses it to set DRAM
voltage on H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This PMIC can be found on H616 boards and it's very similar to AXP805
and AXP806.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The #ifdef CONFIG_xxxPWR conditionals were not working as expected, as
string Kconfig symbols are always "defined" from the preprocessor's
perspective. This lead to unnecessary calls to the GPIO routines, but
also always added a half a second delay to wait for a SATA disk to power
up. Many thanks to Peter for pointing this out!
Fix this by properly comparing the Kconfig symbols against the empty
string. strcmp() would be nicer for this, but GCC does not optimise this
away, probably due to our standalone compiler switches.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi WinPlus
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
dts file is taken from Linux 5.11-rc1 tag.
The Bluetooth controller of this device ships with a default address,
use the new CONFIG_FIXUP_BDADDR option to fix it up.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[Updated OrangePi 3 DT, rebase and config update]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit adds support for Tanix TX6 TV box, based on H6. It's low end
H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other
peripherals.
DT file is taken from Linux 5.11-rc1 release.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
The mt7620_rfb board supports integrated 10/100M PHYs plus two external
giga PHYs. It also has 8MB SPI-NOR, mini PCI-e x1 slot, SDHC and USB.
The mt7620_mt7530_rfb boards supports an external MT7530 giga switch and a
16MB SPI-NOR flash.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M
Nano SoC consisting of baseboard + SOM.
The kit is based on the same design as the Beacon dev kit with
the i.MX8M Mini.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The previous macro was off by one bit and so we were getting a ddr
size which was twice the real size. This commit refactors the macro so
it returns the right size in _bytes_ and modifies the printf call so the
size is still printed in MiB.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
This patch converts the dart6ul ethernet support to DM_ETH and cleans
up the legacy ethernet code. The clean up, more specifically:
* moves the fec2 node and pin definition to the carrier board DTS
since the phy associated with it is on the carrier board and not on
the SoM;
* add the reset pin associated to each phy;
* separate the ethernet, mdio and reset pins of each fec so that they
are easier to reference;
* add clock properties to the phy nodes since they are connected to the
50Mhz ENET[12]_TX_CLK clock of the SoC;
* remove CONFIG_BOARD_EARLY_INIT_F since the function is now empty.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg
The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value
"/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg
The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value "
/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board, we will use
CONFIG_TARGET_IMX8MN_EVK for LPDDR4 EVK board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Giant board is a tiny SBC based on the Adafruit Feather form factor,
created by groboards it contains a SAMA5D2 processor (SAMA5D27),
128 MB of RAM and a microSD card for storage.
Signed-off-by: Greg Gallagher <greg@embeddedgreg.com>
This adds support for the NanoPi R2S from FriendlyArm.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
This hook is used in full U-Boot that's why there is no reason to touch
this location from SPL. The hook was introduced for QEMU usage but none is
really running SPL on QEMU that's why it shouldn't break any usecase.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove ifdef logic which is handled by preprocessor and move it link time
optimization to get full compile code coverage.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For systems which has both sdhci controllers enable it is worth to export
bootseq number for variables. Then the variable can be used in custom
scripts to tune logic for OS.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add the default configuration for the AST2600 EVB.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Add low level platform initialization for the AST2600 SoC.
The 2-stage booting with U-Boot SPL are leveraged to support
different booting mode.
However, currently the patch supports only the booting from
memory-mapped SPI flash.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Our kirkwood device embeds a USB host controller that is now used
on some boards. This enables the support of USB and the corresponding
driver.
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds Microchip MPFS Icicle Kit support. For now, only
NS16550 Serial, Microchip clock, Cadence eMMC and MACB drivers are
enabled. The Microchip MPFS Icicle defconfig by default builds
U-Boot for S-Mode because U-Boot on Microchip PolarFire SoC will run
in S-Mode as payload of HSS + OpenSBI.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
This enables configs necessary for using SPI. The environment is saved to
the very end of SPI flash. This is unlikely to be overwritten unless the
entire flash is reprogrammed.
This also supplies a default bootcommand. It loads an image and device tree
from the first partition of the MMC. This is a minimal/least effort
bootcmd, so suggestions (especially in the form of patches) are welcome. I
didn't set up distro boot because I think it is unlikely that any
general-purpose linux distros will ever be ported to this board.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Chrstopher Obbard <obbardc@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/+yLkACgkQ4rK92eCq
k3X/Fgf/d/11WyQrVzvpr+nN+4Wl7J+ASmoUz0yKa6ri+lbvhLgh+JXbCRKgRPWu
vNnI07pSoX/QeaMpGBU8Ztg/Onb9/pvffz4WMk1411GoyCpDFuuK3cVSIoqkPfu+
XmgSX0u4BXtve1+ZdWfVBWXawUSEDMmGR3tmz1708c/s/oYpnVeRDcqiqzJ94cWE
yt+SpMPVqMUVQ/rAGkE8ToSMxX7FusEa7SvCg4U2ikoRWs3kPpr/73+tRWlmgGxL
sW8SXSKiOmFyheSBx3d2B9n00kDYTTrQmbW9hlMilZmji7CwZYxgTCMdX0x4DeFP
RDajT2Yju1JmeM+Z8+Ke2tupzvy6QA==
=oK8C
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210113' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Enable logging features for stm32mp15 boards
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
A previous series already update STMicroelectronics emails maintainers
but some files have been omitted (Makefile, .dts, .dtsi and .rst files).
Update Patrick and my email address with the one dedicated to upstream
activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
There shouldn't be a need to use loadables propertyn because u-boot can be
pointed by firmware property. This change should also speedup boot process
because loadables property is list of strings which code is going through.
On the other hand firmware can just point to one image.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
USB-C power supply which are Power Delivery compliant (USB-PD) are able
to provide different voltage/current (for example 5V/3A 9V/3A 12V/2.25A...)
In this case, the power supply need to negotiate the voltage/current to
use with the device using CC1/CC2 USB-C signals.
If this negotiation occurs during ADC measurement (done also on CC1/CC2
USB-C signals) some ADC acquisition can be corrupted which cause wrong
power supply current detection.
To avoid this, the power supply current detection algorithm is updated
as following:
- perform an ADC measurement, if a 3A current is detected, continue the
boot process.
- else, wait 20ms (max tPDDebounce duration) to ensure that USB-PD
negotiation is done and perform another ADC measurement.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove board_mmc_init function.
It will be probed with driver-model.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
