This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Since commit f1d2b313c9 the serial
port of the da850evm is accessed before the UART2 peripheral of
the SoC is powered on in the function board_init() in
board/davinci/da8xxevm/da850evm.c.
When u-boot is used in conjunction with the UBL (user boot loader, see
doc/README.davinci) on this board, the UART2 peripheral is already
turned on by UBL at the time u-boot is started. Hence, the wrong
initialization sequence is not noticed by most users. However, if UBL is not
used, u-boot must power on the peripheral before using it.
This patch adds a board_early_init_f() function for the LPSC
configuration to the da850evm board configuration.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
gpio_free() should not have the side effect of setting the line to input since this prevents the gpio command from being able to set a line as output.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
By moving the CS4 configuration into the board specific configuration, it
is left free for custom carrier boards. The USRP-E1XX series uses
CS4 to control access to an FPGA, so without this patch the device driver
cannot claim CS4.
Signed-off-by: Philip Balister <philip@opensdr.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add support for enabling NAND boot mode in configuration file and
add correspanding pinmux support, nand initialize function in board file.
The size required for environment variables not more than 10KB
the CONFIG_ENV_SIZE is set to 10KB from (512 << 10).
Acked-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The level shifters used on the Caspa camera module have a 4k output
impedance. Combined with the 100uA pull-up resistors in the OMAP3,
this raises the ground level to 400mV. Adding crosstalk between the
pixel clock and the HS/VS signals on the flat cable (a ground line in
between would have been nice), logic 0 levels can raise up to 650mV.
This exceeds the camera input pins VIL maximum voltage. This change
suggested-by Laurent Pinchart
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This pad was previously configured for sysclkout_1. This patch changes
the configuration to gpio_10 to reduce radiated noise from the 26Mhz
clock, as well as make the pin more generally useful.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Not all padconfs are the same between 4430 and 4460, so instead of
working around this with an if, we should have an specific padconf
structure for both chips (like handling the differences between the LEDs
GPIOs and TPS).
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the
definition in the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Signed-off-by: Lei Wen <leiwen@marvell.com>
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the
definition in the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Updated cpu.h to remove build errors for gplugd board (by prafulla)
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Copied wholeheartedly from board/Marvell/guruplug and modified to add support
for SPI NOR flash.
CONFIG_MACH_DREAMPLUG defined in include/configs/dreamplug.h until Linus's
kernel.org tree adds it to mach-types.h. Once it trickles down, the definition
can be removed from include/configs/dreamplug.h.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Fix checkpatch warning and errors in several i.MX related files.
While at it also address a checkpatch warning at arch/arm/cpu/armv7/mx5/soc.c
regarding the usage of extern in a C file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Switch to new pmic generic driver.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
Switch to new pmic generic driver.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Enable support for new PMIC driver at GONI reference target.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
setup_weimcs() and some macros are added to support the setup
for i.MX31 WEIM chip selects. As a compromise between verbosity
and readability an ASCII-art'ish bit comment is used instead of
bitfields.
All i.MX31 boards have been patched to use this approach using a
helper program to verify the changes.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
This function is also defined in omap-common/spl_mmc.de so the implementation
in devkit8000.c was protected by a ifdef.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
This adds the required GPIO and pinmux configuration to make eMMC / SD work
on Seaboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
This adds support for changing pinmux functions of pin groups. This is done
by defining a PMUX_FUNC_... enum which can be used to select the function for
each group using pinmux_set_func(). It is also possible to enable
pullup/pulldown, and the existing tristate functionality is retained.
Also provided is a means of configuring a list of pingroups by providing a
configuration table to pinmux_config_table().
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
The pin groupings are better named PINGRP, since on Tegra2 they refer to
multiple pins.
Sorry about this, but better to get it right now when there is only a small
amount of code affected.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
This adds most of the clock functions required by board and driver code:
-query and adjust peripheral clocks
-query and adjust PLLs
-reset and enable control
These functions are plumbed in as required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
This removes clock_init() and pinmux_init() which are names better suited
to those respective modules. By moving board_init_f() to the bottom of the
file we can remove the need for so many functions in the board.h header file.
The only clock/pinmux/gpio init we need to do prior to relocation is
for the UART.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
Rename CLOCK_PLL_ID to CLOCK_ID which takes account of the fact that the
code now deals with both PLL clocks and source clocks.
This also tidied up the assert() to match the one sent upstream, and fixes
an error in the PWM id.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
This is a better name for this protocol. Also remove the typedef to keep
checkpatch happy, and move zeroing of NetBootFileXferSize a little
earlier since TFTPPUT will need to change this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This reverts commit a2da616311.
THis was applied by accident - a more recent version of this change
was already present, see commit
9400f8f 2011-10-05 22:03:11 +0200 km_arm: enable POST for these boards
Signed-off-by: Wolfgang Denk <wd@denx.de>
This driver doesn't support the NET_MULTI framework, and I can't find
any boards/configs/files that reference this subdir, so punt it all.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The board stopped building some time ago, and the board maintainer
agrtees to drop it - see
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/112674
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Seems people fixed their files to use libfoo.o, but didn't actually
update the creation targets to use $(cmd_link_o_target). Update the
rest of the Makefile's found with grep.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Simon Glass <sjg@chromium.org>
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This header is unneeded due to code which was removed in the
past.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Calucations of PRAM needs to take into account the 'rootfssize'.
Memory available to the linux kernel 'mem=' is in all cases set to the total
memory size minus the pram size.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
This prevents u-boot to print out "Can't overwrite "ethaddr""
each time a powerpc board starts.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
The current km_arm boards have a Power-On test jumper. When this
jumper is set, this triggers some Power-On tests on the board.
This patch enables the support of this jumper for starting the
memory_regions test when the jumper is set.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
mpc85xx: Add inline GPIO acessor functions
powerpc/85xx: wait for alignment before resetting SERDES RX lanes (SERDES9)
powerpc/85xx: Fix P2020DS booting
powerpc/85xx: Update USB device tree status based on pin settings
fdt: Add new fdt_set_node_status & fdt_set_status_by_alias helpers
powerpc/85xx: Add support for RMan LIODN initialization
powerpc/85xx: Update device tree handling for SRIO
powerpc/85xx: Update setting of SRIO LIODNs
fm: Don't allow disabling of FM1-DTSEC1
fm-eth: Don't mark the MAC we use for MDIO as disabled in device tree
The work-around for P4080 erratum SERDES9 says that the SERDES receiver
lanes should be reset after the XAUI starts tranmitting alignment signals.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A temp variable was used but not declared, with CONFIG_SYS_DRAMSZ1
defined. This variable is now declared in the functione when needed.
Signed-off-by: Stany MARCEL <stany.marcel@novasys-ingenierie.com>
The spa, stm, int, 32 and 16 linking files are identical so there is
no need to differentiate them. A single lds file is now used, and
_config rule are simplified.
Signed-off-by: Stany MARCEL <stany.marcel@novasys-ingenierie.com>
Lds files cleened to remove multiple defined section and modified to
be compliant with --gc-sections added for ColdFire platform in a
previous patch.
Signed-off-by: Stany MARCEL <stany.marcel@novasys-ingenierie.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The following commit removed the code that set odt_rd_cfg and
odt_wr_cfg. With out this code P2020DS board will not boot:
commit 712cf7ab0b
Author: York Sun <yorksun@freescale.com>
Date: Mon Oct 3 09:19:53 2011 -0700
powerpc/mpc8xxx: Merge entries in DDR speed table
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add common function fdt_set_node_status() to assist in various locations
that we set a nodes status. This function utilizes the status values
that are part of the EPAPR spec (on power.org).
fdt_set_status_by_alias() is based on fdt_set_node_status() but uses an
alias string to identify the node to update.
We also add some shortcut functions to help the common cases of setting
"okay" and "disabled":
fdt_status_okay()
fdt_status_disabled()
fdt_status_okay_by_alias()
fdt_status_disabled_by_alias()
Finally, we fixup the corenet_ds ethernet code which previously had
a function by the same name that can be replaced with the new helpers.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
This adds basic files for the sandbox board. The lds file is very simple
since we can rely mostly on the linker defaults.
Signed-off-by: Simon Glass <sjg@chromium.org>
