So far the TSC timer driver supports trying hardware calibration first
and using device tree as last resort for its running frequency as the
normal timer.
However when it is used as the early timer, it only supports hardware
calibration and if it fails, the driver just panics. This introduces
a new config option to specify the early timer frequency in MHz and
it should be equal to the value described in the device tree.
Without this patch, the travis-ci testing on QEMU x86_64 target fails
each time after it finishes the 'bootefi selftest' as the test.py see
an error was emitted on the console like this:
TSC frequency is ZERO
resetting ...
### ERROR ### Please RESET the board ###
It's strange that this error is consistently seen on the travis-ci
machine, but only occasionally seen on my local machine (maybe 1 out
of 10). Since QEMU x86_64 target enables BOOTSTAGE support which uses
early timer, with this fix it should work without any failure.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In initr_bootstage() we call bootstage_mark_name() which ends up calling
timer_get_us(). This call happens before initr_dm(), which inits driver
model.
On x86 we set gd->timer to NULL in the transition from board_init_f()
to board_init_r(). See board_init_f_r() for this assignment. So U-Boot
knows there is no timer available in the period immediately after
relocation.
On x86 the timer_get_us() call is implemented as calls to get_ticks() and
get_tbclk(). Both of these call dm_timer_init() to set up the timer, if
gd->timer is NULL and the early timer is not available.
However dm_timer_init() cannot succeed before initr_dm() is called.
So it seems that on x86 if we want to use CONFIG_BOOTSTAGE we must enable
CONFIG_TIMER_EARLY. Update the Kconfig to handle this.
Note: On most architectures we can rely on the pre-relocation memory still
being available, so that gd->timer pointers to a valid timer device and
everything works correctly. Admittedly this is not strictly correct since
the timer device is set up by pre-relocation U-Boot, but normally this is
fine. On x86 the 'CAR' (cache-as-RAM) memory used by pre-relocation U-Boot
disappears in board_init_f_r() and any attempt to access it will hang.
This is the reason why we must mark the timer as invalid when we get to
board_init_f_r().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
timer_pre_probe() tries to populate the clock rate from DT. omap
timer driver tries to overwrite this value irrespective of the value
populated fro DT. So update this value only when DT doesn't populate
the clock rate.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In order to handle counter overflows use 64 bit values for counter.
Also load the initial value during probe.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add timer driver for the Designware APB Timer IP. This is present
for example on the Altera SoCFPGA chips.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
At present if TSC frequency is provided in the device tree, it takes
precedence over hardware calibration result. This swaps the order to
try hardware calibration first and uses device tree as last resort.
This can be helpful when a generic dts (eg: coreboot/efi payload) is
supposed to work on as many hardware as possible, including emulators
like QEMU where TSC hardware calibration sometimes fails.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
With the introduction of early timer support in the TSC driver,
the capability of getting clock rate from device tree was lost
unfortunately. Now we bring such functionality back, but with a
limitation that when TSC is used as early timer, specifying clock
rate from device tree does not work.
This fixes random boot failures seen on QEMU targets: printing "TSC
frequency is ZERO" and reset forever.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function is required for adding bootstage support.
Also enable it directly for ZynqMP R5 configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Starting with cpuid level 0x16 (Skylake-based processors)
it is possible to get CPU base freq via cpuid.
This fixes booting on a skylake based system.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed wrong indention of labels]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Use live-tree functions.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The DM driver for ockchip timer blocks is also applicable to the
RK3188 and RK3288 timer blocks: add 'rockchip,rk3188-timer' and
'rockchip,rk3288-timer' to its compatible list to support devices
claiming compatibility with these.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This timer driver is using GPT Timer (General Purpose Timer)
available on all STM32 SOCs family.
This driver can be used on STM32F4/F7 and H7 SoCs family
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
ATCPIT100 is often used in AE3XX platform which is
based on NDS32 architecture recently. But in the future
Andestech will have AE250 platform which is embeded
ATCPIT100 timer based on RISCV architecture.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use dev_get_platdata to get private platdata.
Signed-off-by: rick <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Integrate function and struct name as atcpit100 will be
more reasonable.
Signed-off-by: rick <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ATCPIT100 is Andestech timer IP which is embeded
in AE3XX and AE250 boards. So rename AE3XX to
ATCPIT100 will be more make sence.
Signed-off-by: rick <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It will be work fine with unsigned long declaretion in timer
register struct when system is 32 bit. But it will not work
well when system is 64 bit. Replace it by u32 and verify both
ok in 32/64 bit.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With dtoc emitting fdt64_t for addresses (and region sizes), the array
indices for accessing the reg[] array needs to be adjusted. This
adjusts the Rockchip DM timer driver to correctly handle OF_PLATDATA
given this new structure layout.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the Rockchip timer driver to support a live device tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To make the Rockchip DM timer driver useful for the timing of
bootstages, we need a few enhancements:
- This implements timer_get_boot_us.
- This avoids reinitialising the timer, if it has already been
set up (e.g. by our TPL and SPL stages). Now, we have a single
timebase ticking from TPL through the full U-Boot.
- This adds support for reading the timer even before the
device-model is ready: we find the timer via /chosen/tick-timer,
then read its address and clock-frequency, and finally read the
timeval directly).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
When used with bootstage recording, dm_timer_init may be called
surprisingly early: i.e. before dm_root is ready. To deal with
this case, we explicitly check for this condition and return
-EAGAIN to the caller (refer to drivers/timer/rockchip_timer.c
for a case where this is needed/used).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This updates dm_timer_init to support a live tree and deals with
some fallout (i.e. the need to restructure the code such, that we
don't need multiple discontinuous #if CONFIG_IS_ENABLED blocks).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With bootstage we need access to the timer before driver model is set up.
To handle this, put the required state in global_data and provide a new
function to set up the device, separate from the driver's probe() method.
This will be used by the 'early' timer also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Per the Intel 64 and IA-32 Architecture Software Developer's Manual,
add the reference clock for Intel Atom Processors based on the Airmont
Microarchitecture (Braswell).
This keeps in sync with Linux kernel commit:
6fcb41c: x86/tsc_msr: Add Airmont reference clock values
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When I originally added this driver, I did some careless (and in
retrospect: mindless) copy & paste for the U_BOOT_DRIVER structure
skeletion... unfortunately, the 'arc_timer' string was committed
and slipped through all reviews.
This fixes the U_BOOT_DRIVER name to read 'rockchip_rk3368_timer'
(as originally intended).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reported-by: Artturi Alm <artturi.alm@gmail.com>
This adds a device-model driver for the timer block in the RK3368 (and
similar devices that share the same timer block, such as the RK3288) for
the down-counting (i.e. non-secure) timers.
This allows us to configure U-Boot for the RK3368 in such a way that
we can run with the secure timer inaccessible or uninitialised (note
that the ARMv8 generic timer does not count, if the secure timer is
not enabled).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To fully support DM timer in SPL and TPL, we need a few things cleaned
up and normalised:
- inclusion of the uclass and drivers should be an all-or-nothing
decision for each stage and under control of $(SPL_TPL_)TIMER
instead of having the two-level configuration with TIMER and
$(SPL_TPL_)TIMER_SUPPORT
- when $(SPL_TPL_)TIMER is enabled, the ARMv8 generic timer code can
not be compiled in
This normalises configuration to $(SPL_TPL_)TIMER and moves the config
options to drivers/timer/Kconfig (and cleans up the collateral damage
to some defconfigs that had SPL_TIMER_SUPPORT enabled).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The timer-uclass depends on full OF_CONTROL through its interrogation
of /chosen and the code to determine the clock-frequency.
For the OF_PLATDATA case, these code-paths are disabled and it becomes
the timer driver's responsibility to correctly set the clock-frequency
in the uclass priv-data.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Without a timer, U-Boot just doesn't boot. This is not something
we can turn off.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename try_msr_calibrate_tsc() to cpu_mhz_from_msr(), as that
better describes what the routine does.
This keeps in sync with Linux kernel commit:
02c0cd2: x86/tsc_msr: Remove irqoff around MSR-based TSC enumeration
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Atom processors use a 19.2 MHz crystal oscillator.
Early processors generate 100 MHz via 19.2 MHz * 26 / 5 = 99.84 MHz.
Later processors generate 100 MHz via 19.2 MHz * 125 / 24 = 100 MHz.
Update the Silvermont-based tables accordingly, matching the Software
Developers Manual.
Also, correct a 166 MHz entry that should have been 116 MHz, and add
a missing 80 MHz entry for VLV2.
This keeps in sync with Linux kernel commit:
05680e7: x86/tsc_msr: Correct Silvermont reference clock values
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some processor abbreviations in the comments of freq_desc_tables[]
are obscure. This updates part of these to mention processors
that are known to us. Also expand frequency definitions.
This keeps in sync with Linux kernel commit:
9e0cae9: x86/tsc_msr: Update comments, expand definitions
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If either ratio or freq is zero, the return value is zero. There
is no need to create a fail branch and return zero there.
This keeps in sync with Linux kernel commit:
14bb4e3: x86/tsc_msr: Remove debugging messages
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
try_msr_calibrate_tsc() is currently Intel-specific, and should not
execute on any other vendor's parts.
This keeps in sync with Linux kernel commit:
ba82683: x86/tsc_msr: Identify Intel-specific code
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently we read the tsc radio like this:
ratio = (MSR_PLATFORM_INFO >> 8) & 0x1f;
Thus we get bit 8-12 of MSR_PLATFORM_INFO, however according to the
Intel manual, the ratio bits are bit 8-15.
Fix this problem by masking 0xff instead.
This keeps in sync with Linux kernel commit:
886123f: x86/tsc: Read all ratio bits from MSR_PLATFORM_INFO
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adjust this function to use an ofnode instead of an offset, so it can be
used with livetree. This involves updating all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit introduces timer driver for ARC.
ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.
This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
