The gt90h is a pcb found in generic 9" tablets with an A23 soc, 1G RAM
and 8G nand, rtl8723as usb wifi, 1 micro usb port and 1 micro sd slot.
The pmic setup on this board is somewhat special, dcdc2 MUST be set
to 1.1V instead of the usual 1.2V otherwise the board is very unstable.
aldo1 is used to power the micro sd slot, dldo1 is used for wifi.
This commit adds a defconfig + dts (as submitted to the kernel) for
the gt90h-v4 pcb.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Commit 181bd9dc61 introduced Kconfig selection
for SYS_PROMPT. When applying the new picosam9g45 board this change slipped
through, adopt it.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch enables NAND support on the Marvell Armada XP
DB-MV784MP-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Morrow <peter@senient.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Conflicts:
configs/socfpga_arria5_defconfig
configs/socfpga_cyclone5_defconfig
configs/socfpga_socrates_defconfig
Merged these by hand and re-ran savedefconfig on them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Synchronise the config options with Cyclone V SoCDK and other boards.
This enables ethernet on the ArriaV SoCDK.
Signed-off-by: Marek Vasut <marex@denx.de>
Enable the DWAPB GPIO driver for SoCFPGA Cyclone V and Arria V.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
The CONFIG_TARGET_SOCFPGA_CYCLONE5 and CONFIG_TARGET_SOCFPGA_ARRIA5
selected both a board and a CPU. This is not correct as these macros
are supposed to select only board.
All would be good, if QTS-generated header files didn't check for
these macros exactly to determine if the platform is Cyclone V or
Arria V. Thus, for the sake of compatibility with not well fleshed
out header file generator, this patch makes these two macros into
a stub config option and introduces new CONFIG_TARGET_SOCFPGA_CYCLONE5_SOCDK
and CONFIG_TARGET_SOCFPGA_ARRIA5_SOCDK targets, which select the
previous stub config option.
The result is that compatibility with QTS is preserved and the new
CONFIG_TARGET_* select actual target boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Move config for the E1000 Ethernet driver to Kconfig and tidy up affected
boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Several files are out of order. This means that when the moveconfig tool
moves CONFIG options to Kconfig it generates a large diff. To avoid this,
reorder the files first.
Signed-off-by: Simon Glass <sjg@chromium.org>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
We have to set a MAC address to use network.
Otherwise, the tftpboot command fails with the following message:
Gem.e000b000 Waiting for PHY auto negotiation to complete........ done
*** ERROR: `ethaddr' not set
Since commit 92ac520821 ("net: Remove all references to
CONFIG_ETHADDR and friends"), we can not use CONFIG_ETHADDR.
The easiest way to set a MAC address is to enable
CONFIG_NET_RANDOM_ETHADDR.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We have to set a MAC address to use network.
Otherwise, the tftpboot command fails with the following message:
Gem.e000b000 Waiting for PHY auto negotiation to complete........ done
*** ERROR: `ethaddr' not set
Since commit 92ac520821 ("net: Remove all references to
CONFIG_ETHADDR and friends"), we can not use CONFIG_ETHADDR.
The easiest way to set a MAC address is to enable
CONFIG_NET_RANDOM_ETHADDR.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use embedded DTB to let users use u-boot instead of u-boot-dtb.bin.
And fix SPL to use this target.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added usb dwc3 driver support for zynqmp
this also supports the DFU and LTHOR to download
the linux images on to RAM and cen be booted from
those linux images.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
One disadvantage of commit a26cd04920 (arch: Make board selection
choices optional) is that Kconfig could create such an insane
.config file that no board is selected.
Rip off the "optional" again in favor of ZC702 as the default
target.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.
Now, there are three boards enabling OF_CONTROL on SPL:
- socfpga_arria5_defconfig
- socfpga_cyclone5_defconfig
- socfpga_socrates_defconfig
This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Set up interrupts correctly so that Linux can use all devices. Use
savedefconfig to regenerate the defconfig file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for 4 1.62G lane eDP panels connected via an anx9804 bridge,
such as found on the Colombus devkit.
While at it also fix the wrong indentation of the SSD2828 Kconfig help text
in board/sunxi/Kconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The phy is using a RGMII interface, which we need to specify in our
board-config, and the dts needs a gmac section (the dts changes have
also been submitted to the kernel).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sun5i die has a hdmi encoder onboard, but the A13 package does not
route this to the outside, disable hdmi support on A13 based boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Enable composite video support on all boards which have a composite video
out connector (either cinch or jack).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Auxtek-T003 HDMI stick is an A10s based HDMI stick with USB wifi,
and composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add option to set shell prompt string from menuconfig and migrate
boards globally.
The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
files. This results in a streamlined default value across platforms, and
includes the following files: spear-common, sunxi-common, mv-common,
ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
not updated in their respective defconfig files under the assumption that
since they did not explicitly define a value, they're fine with whatever
the default is.
- On the other hand, boards that relied on a value defined in some
<boards>_common.h file such as woodburn_common, rpi-common,
bur_am335x_common, ls2085a_common, siemens_am33x_common, and
omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
assigning a value for CONFIG_SYS_PROMPT.
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>
Since commit a26cd04920 ("arch: Make board selection choices
optional"), Kconfig could create such an insane .config file that
no SoC/board is selected.
This is now a real problem for Buildroot, for example.
(http://lists.busybox.net/pipermail/buildroot/2015-July/135125.html)
This commit drops the "optional" from the ARM target select menu
in favor of "Versatile family".
Rationale:
- Historically, Linux chose versatile_defconfig as the default
of ARM defconfig. (arch/arm/Makefile of Linux describes:
KBUILD_DEFCONFIG := versatile_defconfig)
- It was published by ARM Ltd.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Import various DT files for DRA7 / DR72x / dra72-evm from Linux Kernel
v4.1
- Add config file for this board, enable DM and DM_GPIO
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Move the CONS_INDEX selection out of CONFIG_SYS_EXTRA_OPTIONS and
into Kconfig proper.
- While in here, enable CONFIG_SPL_STACK_ADDR
Signed-off-by: Tom Rini <trini@konsulko.com>
- Re-sync DT files for am33xx with Linux Kernel v4.1
- Include DT file now for the "AM335x GP EVM" and build target for it,
via device tree and DM.
- We only need to provide platform data for UART when OF_CONTROL isn't
also enabled really. We can just push GPIO to coming from DT
Signed-off-by: Tom Rini <trini@konsulko.com>
Add initial support for CM-T43, an AM437x based SoM.
This support includes: serial, MMC/eMMC, NAND, USB, ETH, I2C, GPIO, DRAM
detection.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
HiKey is the first 96boards consumer edition compliant board. It features a hi6220
SoC which has eight ARM A53 cpu's.
This initial port adds support for: -
1) Serial
2) eMMC / SD card
3) USB
4) GPIO
It has been tested with Arm Trusted Firmware running u-boot as the BL33 executable.
Notes:
eMMC has been tested with basic reading of eMMC partition into DDR. I have not
tested writing / erasing. Due to lack of clock control it won't be
running in the most performant high speed mode.
SD card slot has been tested for reading and booting kernels into DDR.
It is also currently configured to save the u-boot environment to the
SD card.
USB has been tested with ASIX networking adapter to tftpboot kernels
into DDR. On v2015.07-rc2 dhcp now works, and also USB mass storage
are correctly enumerated.
GPIO has been tested using gpio toggle GPIO4_1-3 to flash the LEDs.
Basic SoC datasheet can be found here: -
https://github.com/96boards/documentation/blob/master/hikey/
Hi6220V100_Multi-Mode_Application_Processor_Function_Description.pdf
Board schematic can be found here: -
https://github.com/96boards/documentation/blob/master/hikey/
96Boards-Hikey-Rev-A1.pdf
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
This adds support for the fastboot USB gadget, including flashing to the
internal MMC and reboot to bootloader or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Update to use Kconfig for MUSB]
Signed-off-by: Tom Rini <trini@konsulko.com>
The LG Optimus Black (P970) codename sniper is a smartphone that was designed
and manufactured by LG Electronics (LGE) and released back in 2011.
It is using an OMAP3630 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up. This port is aimed at running an Android version
such as Replicant, the fully free Android distribution. However, support for
upstream Linux with device-tree and common GNU/Linux distros boot commands
could be added in the future.
For more information about the journey to freeing this device, please read the
series of blog posts at:
http://code.paulk.fr/article20/a-hacker-s-journey-freeing-a-phone-from-the-ground-up-first-part
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add CONFIG_OF_SUPPORT]
Signed-off-by: Tom Rini <trini@konsulko.com>
The change adds SPL build support to Timll DevKit3250 board, the
generated SPL image can be uploaded over UART5, JTAG or stored on
NAND. SPL is designed to load U-boot image from NAND.
All new NAND chip defines in board configuration are needed by
SPL NAND "simple" framework, the framework is used to reduce
potentially duplicated code from LPC32xx SLC NAND driver.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
This change adds more peripherals to Timll DevKit3250 board, namely
MAC and SMSC phy, SLC NAND, GPIO, SPI and I2C.
Also the default serial console is changed to UART5, added an option
to pass device tree blob by means of bootm, predefined environment
variables are slightly extended and reserved space on NAND to store
user defined U-boot environment.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
add support for the at91sam9260 based board smartweb from
siemens. SPL is used without serial support, as this
SoC has only 4k sram for running SPL. Here a U-Boot
bootlog:
RomBOOT
>
U-Boot 2015.07-rc2-00109-g4ae828c (Jun 15 2015 - 09:31:16 +0200)
CPU: AT91SAM9260
Crystal frequency: 18.432 MHz
CPU clock : 198.656 MHz
Master clock : 99.328 MHz
Watchdog enabled
DRAM: 64 MiB
WARNING: Caches not enabled
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: macb0
Hit any key to stop autoboot: 0
U-Boot>
Signed-off-by: Heiko Schocher <hs@denx.de>
Add composite video out support.
This only gets enabled on the Mele M3 for now, since that is were it
was tested. It will be enabled on more boards after testing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Jesurun Q5 has the musb hooked up to an usb-a receptacle, enable it
in host-only mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that we have code to check the id-pin and detect usb-host adapters
plugged into the otg port that way, enable it on the tablets which I own.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Enable the otg/drc usb controller on the Wexler TAB7200 tablet.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that the SPL structure is organised such that it matches the
U-Boot's SPL design, it is possible to use the option of relocating
GD to RAM. And since we have GD in RAM, move malloc area to RAM as
well. We point the malloc base pointer 1 MiB past U-Boot's load
address. We use simple malloc for SPL because it is 3kiB smaller
in terms of code size than regular malloc which was used thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
The GMAC can now be probed from OF, so enable DM ethernet and remove the
old ad-hoc designware_initialize() invocation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Add code and configuration options to support booting from QSPI NOR.
Enable support for booting from QSPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
Add code and configuration options to support booting from RAW
SD/MMC card as well as for ext4/vfat filesystems. Enable support
for booting from SD/MMC card, but don't enable the filesystem
support just yet to retain compatibility with old SoCFPGA card
format.
Signed-off-by: Marek Vasut <marex@denx.de>
P2371-0000 is a P2581 or P2530 CPU board married to a P2595 I/O
board. The combination contains SoC, DRAM, eMMC, SD card slot,
HDMI, USB micro-B port, Ethernet via USB3, USB3 host port, SATA,
a GPIO expansion header, and an analog audio jack.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
E2220-1170 is a Tegra210 bringup board with onboard SoC, DRAM,
eMMC, SD card slot, HDMI, USB micro-B port, and sockets for various
expansion modules.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable the debug UART and emit a single 'a' early in the init sequence to
show that it is working.
Unfortunately the debug UART implementation needs a stack to work. I cannot
seem to remove this limitation as the absolute 'jmp %eax' instruction goes
off into the weeds.
So this means that the character output cannot be any earlier than
car_init_ret, where memory is available for a stack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
This should be used for sandbox. We can convert at least one driver to use
it, but in the meantime, enable the feature so that the code is
build-tested.
Signed-off-by: Simon Glass <sjg@chromium.org>
Not all boards use garbage collection in their link step, so we should avoid
adding options that rely on this for prevention of code bloat. Add separate
Kconfig options for syscon and regmap uclasses.
Signed-off-by: Simon Glass <sjg@chromium.org>
Spring is the first ARM-based HP Chromebook 11. It is similar to snow
and it uses the same Samsung Exynos5250 chip. But has some unusual
features. Mainline support for it has lagged snow (both in kernel and
U-Boot). Now that the exynos5 code is common we can support spring just
by adding a device tree and a few lines of configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Chrome OS EC supports tunnelling through to an I2C bus on the EC. This
currently uses a copy of the I2C command code and a special 'crosec'
sub-command.
With driver model we can define an I2C bus which tunnels through to the EC,
and use the normal 'i2c' command to access it. This simplifies the code and
removes some duplication.
Add an I2C driver which tunnels through to the EC. Adjust the EC code to
support binding child devices so that it can be set up. Adjust the existing
I2C xfer function to fit driver model better.
For now the old code remains to allow things to still work. It will be
removed in a later patch once the new flow is fully enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
All T114+ Tegra boards should be using the Kconfig
TEGRA114_SPI switch. Remove it from include/config
and put it into defconfig. Also removed unused
TEGRA114_SPI_CTRLS from T114+ configs.
All Tegra SoCs build OK with this change.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Now that the musb-new driver has a Kconfig, we can move Kconfig options to
enable controllers to it, so that it's easier in e.g. menuconfig.
In addition, this allows declaring support for USB_MUSB_HOST/GADGET in
defconfigs instead of the USB_MUSB_SUNXI controller, that will get selected
automatically when needed.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Add configuration and Kconfig changes for this board.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add PCI IRQ routing information in the board device tree and enable
writing PIRQ routing table and MP table.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Bayley Bay board is a BayTrail based board. Add this board
with existing baytrail fsp support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a cpu1 node to the device tree and enable the MP initialization
on QEMU targets (i440fx and q35).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Fix:
undefined reference to `spi_flash_free'
undefined reference to `spi_flash_probe'
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Stefan Roese <sr@denx.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Stefan Roese <sr@denx.de>
Add kconfig options for various SPI flashes and use them in cm-fx6 defconfig.
Cc: Jagan Teki <jteki@openedev.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add Kconfig options for USB keyboard and use them for cm-fx6.
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add USB_EHCI_MX6 option to menuconfig and use it when migrating cm-fx6 usb
config to defconfig.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
cm-fx6 is an MX6 based board, and the menuconfig hierarchy should
reflect that. Make TARGET_CM_FX6 dependant on ARCH_MX6.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Move CONFIG_CMD_* options that can be selected in menuconfig to cm-fx6
defconfig.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
1. Add DDR script for mx6qpsabreauto board.
2. On CPU3 board, enet RGMII tx clock is from internal PLL. Set the GPR5[9]
and init the enet pll output to 125Mhz.
3. On CPU3 board, SW1ABC=VDDSOC_IN, SW2=VDDARM_IN.
Build target: mx6qpsabreauto_config
Boot Log:
U-Boot 2015.07-rc2-00071-gfd985ff (Jun 29 2015 - 22:10:55 +0800)
CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 34C
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
PMIC: PFUZE100 ID=0x10
Flash: 32 MiB
NAND: 0 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Note:
In this patch, we still add a new config mx6qpsabreauto_config,
since SPL is not supported now, and IMX_CONFIG is needed at
build time, so add this config. Future, when SPL is converted,
this config can be removed.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Secure Boot Target is added for NAND for P5020 and P5040.
The Secure boot target has already been added for P3041 by
enabling CONFIG_SYS_RAMBOOT and configuring CPC as SRAM.
The targets for P5020 and P5040 are added in the same manner.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for NAND for P3041.
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In case of secure boot, this default address maps to Boot ROM.
The Boot ROM code requires that the bootloader(U-boot) must lie
in 0 to 3.5G address space i.e. 0x0 - 0xDFFFFFFF.
In case of NAND Secure Boot, CONFIG_SYS_RAMBOOT is enabled and CPC is
configured as SRAM. U-Boot binary will be located on SRAM configured
at address 0xBFF00000.
In the U-Boot code, TLB entries are created to map the virtual address
0xFFF00000 to physical address 0xBFF00000 of CPC configured as SRAM.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
defconfig files are added and SFP version for these platforms
is updated.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040D4RDB is a Freescale reference board that hosts the T1040 SoC.
T1040D4RDB is re-designed T1040RDB board with following changes :
- Support of DDR4 memory
- Support of 0x66 serdes protocol which can support following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 1 SGMII on DTSEC3
- Support of QE-TDM
Similarily T1042D4RDB is a Freescale reference board that hosts the T1040
SoC. T1042D4RDB is re-designed T1042RDB board with following changes :
- Support of DDR4 memory
- Support for 0x86 serdes protocol which can support following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 3 SGMII on DTSEC1, DTSEC2 & DTSEC3
- Support of DIU
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Based on Venice2, incorporates Stephen Warren's
latest P2571 pinmux table.
With Thierry Reding's 64-bit build fixes, this
will build and and boot in 64-bit on my P2571
(when used with a 32-bit AVP loader).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a RTC node in the device tree to enable DM RTC support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
(Squashed in 'x86: Fix RTC build error on ivybridge')
Move CONFIG_SYS_TEXT_BASE of ZynqMP_ep to its
respective defconfig
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define a new config "zynqmp_ep" for ZynqMP instead
of xilinx_zynqmp. This defconfig supports all emulation
platforms of ZynqMP. Also renamed TARGET_XILINX_ZYNQMP
to ARCH_ZYNQMP.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable DTS support (CONFIG_OF_LIBFDT) and select
CONFIG_FIT in defconfig.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add thermal support so that we can see the following message on boot:
CPU: Industrial temperature grade (-40C to 105C) at 33C
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This patch adds support for the "OHB System AG" baseboard
with is equipped with the TQMa6S SoM.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
Now that the device-model port of the musb mode makes it possible, enable
both the ehci and otg in host mode on boards where the musb is wired up in
host only mode, either via an usb-a receptacle or via an usb <-> sata
converter.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This allows using devices plugged into both ports of the tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When in host mode check if there is a host cable inserted into the otg
port by checking the id pin. If there is no host cable return an error to
make usb_lowlevel_init() exit early, rather then waiting for 1 second
for a device which will never show up.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
With certain features being convert to DM now we want sunxi to default
to having DM enabled for ETH/SERIAL and USB in some cases.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Rini <trini@konsulko.com>
[hdegoede@redhat.com: Also select CONFIG_USB for all sunxi builds]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
The init code for UMC (Unified Memory Controller) and PLL has not
been mainlined yet, but U-boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
To use FIT boot, we have to describe Image Tree Source in addition.
So, it is not intended for beginners. Disable it by default.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds SPL support for the Marvell DB-88F6820-GP board.
With this change, the bin_hdr from the original Marvell U-boot
is not needed any more on this board. The sources from bin_hdr
(SERDES/PHY and DDR setup) are now integrated in mainline
U-Boot. And this patch enables them for this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Add a test to confirm that we can probe this device. Since there is no
MMC stack support in sandbox at present, this is as far as the test goes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move sandbox over to use the reset uclass for reset, instead of a direct
call to do_reset(). This allows us to add tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Freescale DSPI driver has been converted to Driver Model.
The new driver depends on OF_CONTROL, DM, DM_SPI.
This patch enable FSL_DSPI and its dependence configure options.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update crownbay_defconfig and minnowmax_defconfig with 'savedefconfig'
result so that the config option order matches Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Adjust minnowmax to use driver model for PCI. This requires adding a device
tree node to specify the ranges, removing the board-specific PCI code and
ensuring that the host bridge is configured.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable graphics support on Intel Crown Bay board With the help of
vgabios for Intel TunnelCreek IGD. Tested with an external LVDS
panel connected to X4 connector and SDVO adapter connected to X9
connector on the board.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move X86_OPTION_ROM_FILE & X86_OPTION_ROM_ADDR to arch/x86/Kconfig
and rename them to VGA_BIOS_FILE & VGA_BIOS_ADDR which depend on
HAVE_VGA_BIOS. The new names are consistent with other x86 binary
blob options like HAVE_FSP/FSP_FILE/FSP_ADDR.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Crown Bay board has a TunnelCreek processor which supports
hyper-threading. Add /cpus node in the crownbay.dts and enable
the MP initialization.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(modified to remove error:
overriding the value of OF_CONTROL. Old value: "y", new value: "y")
bf533-stamp, bf538f-ezkit, and cm-bf548 are very space limited.
This was introduced by:
6e0d26c050 (net: Handle ethaddr changes as an env callback)
by enabling CONFIG_REGEX, which is too big for these boards.
This patch disables CONFIG_REGEX at the expense of working with more
than the first ethaddr.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
sun8i-a33-ippo-q8h-v1.2-lcd1024x600.dts has been merged into the upstream
Linux kernel as sun8i-a33-ippo-q8h-v1.2.dts, adjust u-boot to follow.
Note we've never shipped a final u-boot version with the old name, so this
is safe todo.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Sinlinx SinA33 is a core/daughter board SDK kit from Sinlinx. It has
the A33 SoC, USB host, USB OTG, audio input/output, LCD, camera, SDIO
and GPIO headers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
There is no good reason to use a particular key to stop autobooting.
The default allows us to stop the autoboot with any key input.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
PI and QSPI only work when boot from QSPI on ls1021a.
This patch only enable options in qspi boot defconfig.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Now that we have the Kconfig based CPU type selection,
use this to fill the IMX_CONFIG automatically
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
This is the first patch to remove the
CONFIG_SYS_EXTRA_OPTIONS.
This patch implements CPU type selection from Kconfig.
Further Kconfig stuff is added later.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
Boards using link-local need lib rand.
When link-local is moved to Kconfig, this dependency will be described
there.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Update new naming scheme.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
rastaban is a draco version with more flash, more RAM
and faster CPU. Number of partitions is the same but
rootfs partition is different.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
add cpsw ethernet boot mode support to download spl and
u-boot.img via tftp protocol. Also adding a seperate config
for ethernet boot mode as the default build falcon mode and
environment on MMC is defined for ethernet boot mode
environment should be set to nowhere.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
While booting via usb host mode, ROM uses DMA to copy MLO over USB so
ARM internal RAM cannot be used. Adding USB host boot support by
introducing new config target which sets SPL_TEXT_BASE to OCMC ram.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The MSI Primo 81 is an Allwinner A31s-based tablet on which the
OTG port is the only accessible USB interface. The existing
defconfig had VGA console on the LCD enabled, but was missing
keyboard support because the prerequisites for that (sunxi MUSB
support and AXP221 GPIO support) had not been available before.
All previously missing dependencies are available now, so this
patch enables keyboard support and its prerequisites in the
defconfig.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Vision Systems's Baltos is based on AM335x SoC
from Texas Instruments. This patch adds support
such Industrial PCs in mainline u-boot.
[ balbi@ti.com: updated original patch to current u-boot ]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 9ba9e85f3f (net: Fix NET_RANDOM_ETHADDR dependencies)
accidentally dropped CONFIG_LIB_RAND defines for 14 Blackfin boards.
Prior to that commit, those boards defined CONFIG_LIB_RAND, but not
CONFIG_NET_RANDOM_ETHADDR. So, commit 9ba9e85f3f should not have
touched them, but in fact it ripped CONFIG_LIB_RAND off from all the
header files, which caused undefined reference to srand and rand.
CONFIG_LIB_RAND=y must be revived for such boards.
BTW, this commit indeed makes it better, but even with this fix,
three boards (bf533-stamp, bf538f-ezkit, cm-bf548) still can not
build due to region 'ram' overflowed error. This was cause by
commit 6eed3786c6 (net: Move the CMD_NET config to defconfigs)
because CMD_NET selects NET, and NET selects REGEX. Eventually,
some boards were newly enabled with CONFIG_REGEX, increasing the
memory footprint. A patch is expected to fix the build error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We plan to enable device tree in SPL by default. Before doing this,
explicitly disable it for all boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable the EC and keyboard, using the SPI bus.
The EC driver requires a particular format and a deactivation delay. Also
U-Boot does not support interrupts.
For now, adjust the device tree to comply. At some point we should tidy
this up to support interrupts and make tegra and exynos use the same setup.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch moves the following config options to Kconfig:
CONFIG_AUTOBOOT_KEYED
CONFIG_AUTOBOOT_PROMPT
CONFIG_AUTOBOOT_DELAY_STR
CONFIG_AUTOBOOT_STOP_STR
AUTOBOOT_KEYED_CTRLC
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Drop ip04 and pm9263 configs/ additions, those boards previously
set CONFIG_AUTOBOOT_PROMPT but never used it, re-run savedefconfig over
all boards that did change. Make digsy_mtc_* string include seconds to
match others and not warn. ]
Signed-off-by: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Most of the drivers available for Vybrid are not yet converted
to OF model to use device tree model, only few drivers
like SPI and GPIO drivers use device trees.
Add separate defconfig for who needs to use device tree model.
Later this can be integrated to single defconfig.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Select CONFIG_CMD_NET and CONFIG_CMD_SETEXPR by default rather then
needing to have this in every sunxi defconfig file.
This also fixes the Merrii_A80_Optimus defconfig no longer building.
Cc: Maxin B. John <maxin.john@enea.com>
Reported-by: Maxin B. John <maxin.john@enea.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add and use a proper dts for the ga10h a33 based tablet, as
submitted upstream.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Rename the Astar_MID756 to Et_q8_v1_6 to match the kernel dts name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Copy over all the latest dts changes from mripard/sunxi/dt-for-4.2 ,
this gives us a proper dtsi file for the A33 rather then abusing
sun8i-a23.dtsi for this.
And this replaces our minimal (dummy) sun7i-a20-mk808c and
sun8i-a33-astar-mid756 dts files with proper ones.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been
using the same defconfig (and dts on the kernel side) for both models.
Unfortunately this does not work for the otg controller, on the M9 this
is routed to a micro-usb connector on the outside, while as on the
A1000G-quad it is connected to an usb to sata bridge.
This commit adds a new defconfig for the Mele-A1000G-quad to allow using
different otg controller settings on the 2 boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Support QEMU PIRQ routing via device tree on both i440fx and q35
platforms. With this commit, Linux booting on QEMU from U-Boot
has working ATA/SATA, USB and ethernet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Although the two qemu-x86 targets (i440fx and q35) share a lot in
common, they still have something that cannot easily handled in one
single device tree). Split to create two dedicated device tree files
and make the i440fx be the default build target.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Quark SoC has the same interrupt routing mechanism as the
Queensbay platform, only the difference is that PCI devices'
INTA/B/C/D are harcoded and cannot be changed freely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
It turns out that QEMU x86 emulated graphic card has a built-in
option ROM which can be run perfectly with native mode by U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_FRAMEBUFFER_SET_VESA_MODE and CONFIG_FRAMEBUFFER_VESA_MODE
are not x86-specific, so move them to drivers/video/Kconfig and
make them depend on VIDEO_VESA driver. Some cosmetic fixes are
applied to the Kconfig help text as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
QEMU is much easier for us test booting U-Boot as a coreboot payload
than having a real board like chromebook_link.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Now that we have QEMU support, make it the default vendor in the
'make menuconfig' screen.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This commit introduces the initial U-Boot support for QEMU x86 targets.
U-Boot can boot from coreboot as a payload, or directly without coreboot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Merged in patch 'x86: qemu: Add CMD_NET to qemu-x86_defconfig
https://patchwork.ozlabs.org/patch/479745/
This also selects CONFIG_NET for any CONFIG_CMD_NET board.
Remove the imx default for CONFIG_NET.
This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Another shell scripting command that has not been moved.
Moved using tools/moveconfig.py using these settings:
CMD_SETEXPR bool n y
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 76ec988b06 (net: Remove all calls to net_random_ethaddr())
accidentally deleted CONFIG_TARGET_BCT_BRETTL2=y, and since then
bct-brettl2 would not build.
Since commit a26cd04920 (arch: Make board selection choices
optional), Kconfig actually allows such a .config file in which no
board is selected, but the build never succeeds.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since commit 92ac520821 (net: Remove all references to
CONFIG_ETHADDR and friends), the ethernet device on UniPhier boards
is not working because of the incorrect (all-zero) MAC address.
Enable CONFIG_NET_RANDOM_ETHADDR to generate the random one.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
One disadvantage of commit a26cd04920 (arch: Make board selection
choices optional) is that Kconfig could create such an insane
.config file that no board is selected.
As PH1-Pro4 is the main stream of UniPhier SoC family, rip off the
"optional" again in favor of PH1-Pro4 as the default SoC.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Prior to this commit, ZC702 and ZC706 shared the same configuration
and were built as follows:
ZC702: make zynq_zc70x_defconfig && make
ZC706: make zynq_zc70x_defconfig && make DEVICE_TREE=zynq-zc706
This commit introduces separate configuration for them, which makes
the next commit much easier.
Going forward, the recommended build commands are:
ZC702: make zynq_zc702_defconfig && make
ZC706: make zynq_zc706_defconfig && make
Although the old work flow is still supported, CONFIG_TARGET_ZC70X
has been marked as deprecated. If used, the warning message is
shown to prompt users to switch to the new scheme.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit allows users to enable/disable the Freescale NFC
controller found in systems like Vybrid (VF610), MPC5125, MCF54418
or Kinetis K70 via Kconfig with more detailed help docs.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
[scottwood: updated vf610twr_nand_defconfig]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Currently we need to build one U-boot image for each of the wandboard
variants: quad, dual-lite and solo.
By switching to SPL we can support all these variants with a single binary,
which is very convenient.
Based on the work from Richard Hu.
Tested kernel booting on the three boards.
Signed-off-by: Richard Hu <hakahu@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Vagrant Cascadian <vagrant@aikidev.net>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Make all unit tests selectable as a menu of test suites instead of just
sitting in the top-level menu individually.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify the command for running unit tests further by moving the "ut_time"
command over to "ut time".
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Unify the command for running unit tests further by moving the "dm test"
command over to "ut dm".
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Stop using the sandbox arch Kconfig to override defaults for config
options. This is a bit of abuse and may be causing build problems.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
