SPI recieve and transfer code in exynos_spi driver has a logical bug.
We read data in a variable which can hold an integer. Then we assign
this integer 32 bit value to another variable which has data type uchar.
Latter represents a unit of our recieve buffer. Everytime when we write
a value to our recieve buffer we step ahead by 4 units when actually we
wrote to one unit. This results in the loss of 3 bytes out of every 4
bytes recieved. This patch intends to fix this bug.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This allows us to put the SPI flash chip inside the SPI interface node,
with U-Boot finding the correct bus and chip select automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since SPI register access is so expensive, it is worth transferring data
a word at a time if we can. This complicates the driver unfortunately.
Use the byte-swapping feature to avoid having to convert to/from big
endian in software.
This change increases speed from about 2MB/s to about 4.5MB/s.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Accessing SPI registers is slow, but access to the FIFO level register
in particular seems to be extraordinarily expensive (I measure up to
600ns). Perhaps it is required to synchronise with the SPI byte output
logic which might run at 1/8th of the 40MHz SPI speed (just a guess).
Reduce access to this register by filling up and emptying FIFOs
more completely, rather than just one word each time around the inner
loop.
Since the rxfifo value will now likely be much greater that what we read
before we fill the txfifo, we only fill the txfifo halfway. This is
because if the txfifo is empty, but the rxfifo has data in it, then writing
too much data to the txfifo may overflow the rxfifo as data arrives.
This speeds up SPI flash reading from about 1MB/s to about 2MB/s on snow.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
For devices that need some time to react after a spi transaction
finishes, add the ability to set a delay.
Implement this as a delay on the first/next transaction to avoid
any delay in the fairly common case where a SPI transaction is
followed by other processing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This patch adds SPI support for carrying out the cros_ec protocol.
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Support interfaces with a preamble before each received message.
We handle this when the client has requested a SPI_XFER_END, meaning
that we must close of the transaction. In this case we read until we
see the preamble (or a timeout occurs), skipping all data before and
including the preamble. The client will receive only data bytes after
the preamble.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Enclosing process_nodes() and spi_get_config() inside
CONFIG_OF_CONTROL, since they are compiled only for DT systems.
This fixes following warning:
exynos_spi.c:391:12: warning: 'process_nodes' defined but not used [-Wunused-function]
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rather than each driver having its own way to allocate a SPI slave,
use the new allocation function everywhere. This will make it easier
to extend the interface without breaking drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds FDT support to the SPI driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds SPI driver for EXYNOS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: jy0922.shim@samsung.com
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
