Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
Rework rpi_b's bootcmd (and sub-commands) to match Tegra's bootcmd as
much as possible. This will aid in a future patch which will create a
common header e.g. config_distro_bootcmd.h.
While at it, enable booting from extlinux.conf using the sysboot command.
The iteration and componentization currently makes a little more sense
for Tegra than RPi, but I'd still like to keep the two as similar as
possible. USB and networking support is coming to the RPi in due course,
and it'll all make more sense then anyway.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The Pi has no flash to store an environment in the usual fashion. However,
the user may wish to customize the environment. We know that the SD card
must be present, since that's where the boot ROM has loaded U-Boot from.
So, load uEnv.txt from there early during boot. This allows the user to
e.g. customize boot_targets, in order to automatically select network
boot.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Modify the rpi_b board to include the "distro defaults" header, so that
all the config options distros expect are enabled. Remove any #defines
that enable the same options from the rpi_b.h.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
U-Boot names the Raspberry Pi board rpi_b. This means that the common
expression for DTB filename ${soc}-${board}.dtb expands to
bcm2835-rpi_b.dtb. However, the DTB generated by the Linux kernel is
bcm2835-rpi-b.dtb. Set $fdtfile in U-Boot's environment so that scripts
look for the correct DTB filename.
An alternative would be to rename the U-Boot board to rpi-b. However,
that change would be far more invasive, and end up affecting users (i.e
they'd have to change their U-Boot build commands).
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Add a DT simple-framebuffer node to DT when booting the Linux kernel.
This will allow the kernel to inherit the framebuffer configuration from
U-Boot, and display a graphical boot console, and even run a full SW-
rendered X server.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Simon Glass <sjg@chromium.org>
Apparently, CONFIG_SYS_HZ must be 1000. Change this, and fix the timer
driver to conform to this.
Have the timer implementation export a custom API get_timer_us() for use
by the BCM2835 MMC API, which needs us resolution for a HW workaround.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Enable the SD controller driver for the Raspberry Pi. Enable a number
of useful MMC, partition, and filesystem-related commands. Set up the
environment to provide standard locations for loading a kernel, DTB,
etc. Provide a boot command that loads and executes boot.scr.uimg from
the SD card; this is written considering future extensibilty to USB
storage.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The firmware running on the bcm2835 SoC's VideoCore CPU manages the
display controller. Add a simple "LCD" driver that communicates with the
firmware using the property mailbox protocol. This configures the
display and frame-buffer to match whatever physical resolution the
firmware chosen when booting, which is typically the native resolution
of the attached display device, presumably unless otherwise specified
in config.txt on the boot media.
Enable this driver in the Raspberry Pi board configuration.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
There appears to be no implementation of flush_dcache_range() for
ARM1176, so explicitly disable dcache support to avoid references to
that function from the LCD core in the next patch. This was presumably
not noticed before simply because no drivers for the rpi_b were
attempting DMA.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The Raspberry Pi model B uses the BCM2835 SoC, has 256MB of RAM,
contains an SMSC 9512 USB LAN/Hub chip, and various IO connectors.
For more details, see http://www.raspberrypi.org/.
Various portions (cache enable, MACH_TYPE setup, RAM size limit, stack
relocation to top of RAM) extracted from work by:
Oleksandr Tymoshenko <gonzo@bluezbox.com>.
GPIO driver enablement by Vikram Narayanan <vikram186@gmail.com>.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Tom Rini <trini@ti.com>
