The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
dev_read_addr_ptr instead of the dev_read_addr function in the
various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Please pull the second part of the sunxi pull request for this cycle.
Another bunch of patches that replace old-school U-Boot hacks with
proper DM based code, this time for the raw NAND flash driver, and the
USB PHY VBUS detection code. Plus two smaller patches that were sitting
in my inbox for a while.
Gitlab CI passed. In lack of some supported board with NAND flash I
couldn't really test this part, but apparently this was tested by the
reviewer. I briefly ran the branch on some boards with USB-OTG, and
this still worked.
This pull request adds support for the last CPU board from
CS GROUP France (previously CSSI).
That CPU board called CMPCPRO has a mpc8321E CPU (Family PQII PRO hence
its name) and can be plugged in place of the CMPC885 board.
In order to support that new board, the following changes are included
in this series:
- Make the mpc8xx watchdog driver more generic for reusing it
with mpc83xx
- Fix various small problems on mpc83xx platform
- Add a GPIO Driver for QE GPIOs
- Add support for mpc832x into mpc83xx SPI driver
- Refactor existing board code that will be shared with new board
- Add the new board
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
By the time we jump to the err label, count represents the number of
gpios we've successfully requested. So by subtracting one, we fail to
free the most recently requested.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GPIO V2 controller on RK3568 and RK3588 works very similar to
prior generation, main difference is the use of a write mask in the
upper 16 bits and register address offset have changed.
GPIO_VER_ID is a new register at 0x0078 that is used to determine when
the driver should use new or old register offsets and values. Earlier
generation return 0x0 from this offset.
Refactor code and add support for the GPIO V2 controller used in RK3568
and RK3588.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The current divider to calculate the bank ID can change.
Given the Rockchip TRM not all gpio-banks have 32 pins per bank.
The "gpio-ranges" syntax allows multiple items with variable number
of pins. Use a constant ROCKCHIP_GPIOS_PER_BANK as fixed divider.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add pinctrl tables for R8A779F0 S4 SoC.
Based on Linux next 20230228 PFC tables tables up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Use RCAR_64 Kconfig, sync with Linux next 20230228]
Add support for the GPIO controller block in the R-Car Gen4 family.
It has a General Input Enable Register (INEN), whose reset state is to
have all inputs disabled.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The mpc832x has GPIOs handled by the QUICC Engine.
The registers are different from the one for the
non QE mpc83xx GPIOs.
Implement a GPIO driver for those.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
The API is more convenient to use if one doesn't have to know upfront
which gpio controller has a line with the name one is searching for,
and arrange to look that device up somehow. Or implement this loop
oneself.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Switch ifdef in sh_gpio_get_value() to IS_ENABLED() macro.
The CONFIG_RCAR_GEN3 will never have SPL counterpart, so
the IS_ENABLED() macro is the right one here. No functional
change, except for improved build test coverage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Use the new devicetree property of gpio-ranges to determine the GPIO
bank ID. Preserve the "old" way of doing things too, so that boards
can be migrated and tested gradually (I only have a 3566 and 3326 to
test).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- A fix for a long standing bug that has been exposed by commit
50128aeb0f ("cyclic: get rid of cyclic_init()") preventing 8xx boards
from booting since u-boot 2023.01
- A GPIO driver for powerpc 8xx chip
- Fixup for powerpc 8xx SPI driver
- A new powerpc 8xx board
- The two devices having that board.
Ports A, C and D are 16 bits ports.
Ports B and E are 32 bits ports.
The "compatible" is used to determine each port type.
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
GPIO button driver requires direction functions to probe
button gpio. Those functions are blank, since pwrkey is not
really gpio, and don't support direction settings.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
This is not used since this commit:
7458f18e5c ppc: Remove MPC8313ERDB boards
Drop the driver and Kconfig option.
Signed-off-by: Simon Glass <sjg@chromium.org>
The KONA and KONA_GPIO options don't exist anymore, since this commit:
0f6807e77b arm: Remove bcm28155_ap board
Drop the dead code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Synchronize R-Car PFC core with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Parts picked from
pinctrl: renesas: Synchronize R-Car Gen2/Gen3 tables with Linux 5.18.3
- Add pin groups for the green and high8 subsets of the Video IN pins
- Add MediaLB pins
- Add bias support for various SoCs
- Share more pin group data, to reduce size and ease review
- Miscellaneous cleanups, fixes and improvements.
This contains port of Linux kernel commit
6210905586ae ("pinctrl: renesas: Add shorthand for reserved register fields")
to handle negative entries in GROUP() macros correctly.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCY9PmzwAKCRDKSWXLKUoM
IYWxAJwNgiXtFT17pBy+1M0JvSWgyvWF3QCfTQG2Krnw0+d65PF5A7UFTDL7SZM=
=cMrc
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx chnages for v2023.04-rc1
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
There is a unused variable ret, due to which we are getting sparse warning
as below.
warning: variable 'ret' set but not used [-Wunused-but-set-variable].
Return ret incase of error.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230120053617.32463-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The gpio_hog_probe_all() functionality can be perfectly well replaced by
DM_FLAG_PROBE_AFTER_BIND DM flag, which would trigger .probe() callback
of each GPIO hog driver instance after .bind() and thus configure the
hogged GPIO accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As CONFIG_ARCH_BCM6753 is replaced with CONFIG_BCM6855, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM6858 is replaced with CONFIG_BCM6858, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM68360 is replaced with CONFIG_BCM6856, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM63158 is replaced with CONFIG_BCM63158, update the
Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
uclass_first_device/uclass_next_device return value will be removed,
don't use it.
With the current implementation dev is equivalent to !ret. It is
redundant to check both, ret check can be replaced with dev check, and
ret check inside the iteration is dead code.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Matching anything that just happens to have the sought-for label as a
prefix is wrong. For example, if the board designer has designated 10
lines for debug purposes, named "debug1" through "debug10", and we are
looking up "debug1", if debug10 happens to be met first during the
iteration we'd wrongly return that.
In theory, this can break existing users that could rely on this
quirk, but OTOH keeping the current broken semantics can cause a lot
of grief for people hitting this in the future and not understanding
why they don't find the line they expect. Considering how few in-tree
defconfigs currently set DM_GPIO_LOOKUP_LABEL (ignoring sandbox, only
four "real" boards), let's fix it before the use becomes more
widespread.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add gpio driver for ADP5585 I/O Expander Controller. The ADP5585 is a 10
input/output port expander and can be used to increase the number of
I/Os available to a processor.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Currently all GPIOs supported by CMD_EXT_CONTROL/CMD_GET_EXT_CONTROL_STATUS
commands (last 16 GPIOs) are available only when FEAT_PERIPH_MCU feature
bit is set. So do not register these GPIOs by U-Boot driver when this
feature bit is not set, so U-Boot 'gpio' command would see only GPIOs which
really exists.
Fixes: 5e4d24ccc1 ("gpio: Add Turris Omnia MCU driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This has been done in order to align the DT of U-Boot with the DT
of Linux. In Linux, a phandle from a '-gpio' DT property is linked
to the pinctrl driver, a single driver that handles both pinctrl
settings and offers GPIO API to callers. On the other hand,
U-Boot redirects such phandle to a corresponding UCLASS_GPIO
driver, because U-Boot offers two different types of drivers
in this case: UCLASS_PINCTRL which handles pin functions and
UCLASS_GPIO which handles gpio requests as a gpio provider.
Due to this, we have two drivers in Uboot, but the Devicetree
has a single node. Thus, just one of the drivers can be probed
for the DT node during platform initialization, before relocation.
Our previous solution in U-Boot was to have a different devicetree:
the gpio node has a subnode for the pinctrl driver, which
is not compliant with Linux ABI. Furthermore, our documentation
for this type of nodes mentions no such gpio compatible.
After this patch, we can no longer add nodes with a gpio
compatible in the DT. Thus, in order to link the pinctrl driver to
the gpio one, a hook to the bind method of the former in U-Boot has
been added and the GPIO related compatibles have been removed to
avoid conflict when compatibles are enumerated and bound to drivers
during platform start before relocation. The bind method will attach
the GPIO driver to the pinctrl DT node so that every phandle coming
from '-gpio' DT properties will be redirected to a valid driver
attached to the pinctrl DT node.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
This allows to test if a pin's label if displayed using gpio_get_status()
when this pin is configured in alternate function.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Even pin with GPIOF_UNUSED function can have a label.
The criteria to add or not a space character is linked to label not to
the used/unused status.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Currently for all Qcom SoCs/boards there are separate compatibles for
GPIO and pinctrl. But this is inconsistent with official (upstream) Linux
bindings which requires only a single compatible "qcom,<SoC name>-pinctrl"
and there is no such compatible property as "qcom,tlmm-<SoC name>".
So fix this inconsistency for Qcom SoCs in order to comply with upstream
DT bindings. This is done via removing compatibles from "msm_gpio" driver
and via binding to "msm_gpio" driver from pinctrl driver in case
"gpio-controller" property is specified for pinctrl node.
Suggested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
GPIO LV (low voltage)/MV (medium voltage) subtypes have different
features and register mappings than 4CH/8CH subtypes. Add support
for LV and MV subtypes.
With GPIO LV/MV subtype available, add "qcom,pms405-gpio" compatible
which requires support for GPIO MV subtype.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Since both pm8916.c and pm8916_gpio.c are already supporting multiple
Qcom SoCs, it makes sense to rename these drivers to pmic_qcom.c and
qcom_pmic_gpio.c respectively. Also, these driver can be extended to
support additional functionality if required for other Qcom SoCs.
Along with this import latest DT binding: qcom,spmi-pmic.txt from Linux
kernel and thereby remove pm8916.txt.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
The last user of this driver was removed in commit dee08b1999 ("arm:
Remove gplugd board"). Remove the unused driver.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Pali Rohár <pali@kernel.org>
CMD_GENERAL_CONTROL takes two 8-bit arguments but CMD_EXT_CONTROL takes
two 16-bit arguments. Fix this issue and change CMD_EXT_CONTROL arguments
to 16-bit.
Fixes: 5e4d24ccc1 ("gpio: Add Turris Omnia MCU driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
