Commit Graph

5659 Commits

Author SHA1 Message Date
Marek Vasut
26822fd23c ARM: imx: vining2000: Convert to ethernet DM
Convert the board to ethernet DM support. Adjust board file accordingly,
as the board_eth_init() contains custom clock configuration required for
this board to work. Furthermore, enable FEC1 clock to make FEC1 work as
well.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-12-06 13:57:42 +01:00
Marek Vasut
5b97abab55 ARM: imx: vining2000: Enable DDR DRAM calibration
Enable DRAM calibration in SPL to improve behavior of the board
in edge conditions of the thermal envelope of the board and make
it even more stable.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-12-06 13:57:42 +01:00
Marek Vasut
7d84f4469f ARM: imx: vining2000: Convert to SPL framework
In preparation for use of DDR DRAM fine-tuning upon boot,
convert the board to SPL framework instead of using DCD
tables to bring up DRAM and pinmux.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-12-06 13:57:42 +01:00
Fabio Estevam
1fae23899c warp7: Fix U-Boot corruption after saving the environment
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.

Running "saveenv" followed by a "reset" causes U-Boot to hang because
of this overlap.

Fix this problem by increasing the CONFIG_ENV_OFFSET size.

Also, in order to prevent this same problem in the future, use
CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time.

CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare
CONFIG_ENV_OFFSET with its direct value instead.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Acked-by: Joris Offouga <offougajoris@gmail.com>
Tested-by: Joris Offouga <offougajoris@gmail.com>
2019-12-06 12:09:25 +01:00
Ben Wolsieffer
893b4d0df4 rockchip: rk3328: rock64: enable CONFIG_MISC_INIT_R
This enables reading of the cpuid and a static MAC address.

Signed-off-by: Ben Wolsieffer <benwolsieffer@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-06 00:06:23 +08:00
Kever Yang
502573686f rockchip: config: add support for firefly-px30 board
This is a core board named Core-PX30-JD4 with a mainboard from Firefly,
name it as firefly-px30 for now.
This board can re-use the dts of PX30, the only difference is the UART IO,
the firefly use UART2 M1 while evb use UART2 M0.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-06 00:06:23 +08:00
Andy Yan
1b8114ac1e rockchip: evb-px5: disable NET
PX5 evb has no ETH port, so disable it.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-12-05 23:53:07 +08:00
Adam Ford
8cc738b9fc ARM: omapl138_lcdk: Shrink code size by building with Thumb
SPL has limited available resources, and the performance between
ARM and Thumb isn't that significant.

This patch builds using Thumb instruction set to reduce the code
size by nearly 6K.

Original:
   text	   data	    bss	    dec	    hex	filename
  26526	   4004	   1376	  31906	   7ca2	spl/u-boot-spl

Thumb:

   text	   data	    bss	    dec	    hex	filename
  20232	   4004	   1376	  25612	   640c	spl/u-boot-spl

Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-12-05 10:28:39 -05:00
Adam Ford
81b564353d ARM: da850-evm: Disable SYS_MMCSD_RAW_MODE_USE_SECTOR
The da850-evm doesn't have the boot pins configured in a way
to make MMC/SD booting an option, and MMC/SD support is not
enabled in SPL.  Therefore, there is no need to support raw mode
mmc/sd support in SPL.

This patch disables CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-12-05 10:28:39 -05:00
Tom Rini
7e5ee346fc Merge git://git.denx.de/u-boot-sh
- Convert some R-Car Gen3 platforms to DM_SPI{,_FLASH}
2019-12-04 18:10:04 -05:00
Tom Rini
0cfccb5401 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 17:18:38 -05:00
Miquel Raynal
f3a02d29e8 dfu: add dependency on the raw NAND core
CONFIG_DFU_NAND needs the raw NAND core being compiled.

Also fix the colibri_vf defconfig to reflect this dependency.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-04 17:10:51 -05:00
Miquel Raynal
e81f03248e configs: ls104x/ls108x/ls208x: Build the raw NAND core with TFABOOT
Enabling TFABOOT configuration will compile-in a call to nand_read in
the boot sequence. Handle the situation by also selecting officially
the raw NAND core in this case.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-12-04 17:10:51 -05:00
Miquel Raynal
7db785c703 configs: socfpga: mcvevk: Remove useless UBI infos
There is no flash on this board, there is no reason to define MTD
environment variables nor UBI. Drop them from the configuration file.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Wolfgang Grandegger <wg@aries-embedded.de>
2019-12-04 17:10:51 -05:00
Miquel Raynal
910bc26ee9 configs: remove MTD support from bcm11130 and M54418TWR defconfigs
While the right Kconfig entries were selected, because of the missing
CMD_NAND symbol the raw NAND core was never compiled. Remove it from
the defconfigs otherwise the build will fail.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Also do this on bcm11130_nand]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 13:26:17 -05:00
Miquel Raynal
452f22e7e3 configs: remove raw NAND core from k2g defconfigs
Due to previous Makefile organization, the raw NAND subdirectory was
not compiled in if CMD_NAND was not enabled. Because the Denali driver
does not compile with these boards (undefined environment offset),
remove the dependency within the defconfig over the controller driver
(was ignored anyway in the past).

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2019-12-04 13:26:17 -05:00
Miquel Raynal
e0a4c2d2a7 configs: move CONFIG_MTD in defconfigs when set in arch includes
Let's be consistent and always declare CONFIG_MTD from the defconfig
file when needed.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-04 13:26:17 -05:00
Miquel Raynal
f6434a9561 mtd: ensure MTD is compiled when CMD_MTDPARTS is selected
MTD support must be enabled when using mtdparts. Indeed, functions
like get_mtd_info(), get_mtd_device() and put_mtd_device() are in
drivers/mtd/mtd_uboot.c and are built only with CONFIG_MTD.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-04 13:26:17 -05:00
Miquel Raynal
2fa872ee77 mtd: ensure CMD_NAND is compiled when its options are selected
In some files, options of CMD_NAND are selected but not the command
itself. Fix this inconsistency.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-04 13:26:17 -05:00
Miquel Raynal
7ccc3f3018 mtd: ensure MTD_RAW_NAND is compiled when ENV_IS_IN_NAND is selected
Raw NAND support must be enabled when the environment is in NAND.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-04 13:26:17 -05:00
Miquel Raynal
00e270473e mtd: ensure UBI is compiled when ENV_IS_IN_UBI is selected
UBI must be enabled when the environment is in UBI.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-04 13:26:17 -05:00
Miquel Raynal
f344fb1540 mtd: ensure UBI is compiled when using fastmap
UBI must be enabled when using fastmap, reflect this is defconfigs.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-04 13:26:17 -05:00
Miquel Raynal
63ea317245 mtd: ensure MTD is compiled when there is a SPI NOR flash using MTD
MTD must be enabled when there is a SPI NOR flash using the
SPI_FLASH_MTD config entry.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-04 13:26:17 -05:00
Miquel Raynal
d4c2f6b7e3 mtd: ensure MTD/the raw NAND core are compiled when there is a NAND flash
Both symbols must be enabled when there is a raw NAND driver
selected. Also enable them when CONFIG_CMD_NAND is selected to avoid
breaking things when we'll further rework the MTD dependency
description.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Rebase and migrate a few more boards here]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 13:26:17 -05:00
Marek Vasut
019c9b3ea8 ARM: rmobile: Convert M2N Gose to DM_SPI{,_FLASH}
Enable DM_SPI and DM_SPI_FLASH in U-Boot on M2N Gose.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-12-04 18:57:05 +01:00
Marek Vasut
d22c65d139 ARM: rmobile: Convert M2W Koelsch to DM_SPI{,_FLASH}
Enable DM_SPI and DM_SPI_FLASH in U-Boot on M2W Koelsch.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-12-04 18:57:05 +01:00
Marek Vasut
20be3e2ca7 ARM: rmobile: Convert H2 Lager to DM_SPI{,_FLASH}
Enable DM_SPI and DM_SPI_FLASH in U-Boot on H2 Lager.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-12-04 18:57:04 +01:00
Miquel Raynal
888f184abe mtd: rename CONFIG_MTD_DEVICE -> CONFIG_MTD
Like in Linux, just use CONFIG_MTD to compile the MTD stack.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Miquel Raynal
1de770d544 mtd: rename CONFIG_MTD -> CONFIG_DM_MTD
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Add Kconfig files]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03 23:04:10 -05:00
Miquel Raynal
88718be300 mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND
Add more clarity by changing the Kconfig entry name.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Michal Simek
c9f417b28a arm64: zynqmp: Point zcu216 defconfig to correct dts file
Defconfig is pointing to incorrect DT file which needs to be fix.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-12-03 12:00:25 -05:00
mingming lee
abf2c68566 ARM: MediaTek: add basic support for MT8518 boards
This adds a general board file based on MT8518 SoCs from MediaTek.

Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.

This commit is adding the basic boot support for the MT8518 eMMC board.

Signed-off-by: mingming lee <mingming.lee@mediatek.com>
[trini: Migrate env location to defconfig, set ENV_IS_IN_MMC]
Signeed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03 12:00:03 -05:00
Adam Ford
5d7f5ac38e ARM: omapl138_lcdk: Enable SPL_DM_SEQ_ALIAS and SPL_OF_TRANSLATE
In order to further prepare for full device tree support in SPL,
this patch enables both SPL_DM_SEQ_ALIAS and SPL_OF_TRANSLATE.
Both of these are already enabled in U-Boot, so SPL will have
the same functionality

Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-12-03 08:44:13 -05:00
Adam Ford
cfa84e3206 ARM: omapl138_lcdk: Increase malloc pool before relocation
Driver model requires a malloc pool to allocate memory before
relocations to operate serial and some other devices.  This patch
increases the pool size to 2K.

Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-12-03 08:44:13 -05:00
Adam Ford
efa68e82a2 ARM: omapl138_lcdk: Separate BSS in SPL
In preparation to use full device tree support, SPL can separate
BSS from text region.

This patch enables SPL_SEPARATE_BSS.

Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-12-03 08:43:24 -05:00
Tom Rini
e78f16b751 Convert CONFIG_SYS_CORTINA_FW_IN_MMC et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_CORTINA_FW_IN_MMC
   CONFIG_SYS_CORTINA_FW_IN_NAND
   CONFIG_SYS_CORTINA_FW_IN_NOR
   CONFIG_SYS_CORTINA_FW_IN_REMOTE
   CONFIG_SYS_CORTINA_FW_IN_SPIFLASH

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03 08:43:24 -05:00
Tom Rini
60f3c01596 Convert CONFIG_PHY_CORTINA to Kconfig
This converts the following to Kconfig:
   CONFIG_PHY_CORTINA

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03 08:43:24 -05:00
Tom Rini
9a94a8994a tbs2910: Disable VxWorks image booting support
There are currently no known users of this functionality on this
platform, disable it to prepare for additional VxWorks functionality
that would cause this platform to fail to link.

Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Soeren Moch <smoch@web.de>
2019-12-03 08:43:23 -05:00
Tom Rini
a80a49b237 tbs2910: Disable VxWorks image booting support
There are currently no known users of this functionality on this
platform, disable it to prepare for additional VxWorks functionality
that would cause this platform to fail to link.

Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Soeren Moch <smoch@web.de>
2019-12-03 11:13:05 +01:00
Tom Rini
357040645f Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- fsl-qoriq : Minor bug fixes and updates on lx2160a, ls1028a, ls1012a,
  ls1043aqds platforms
2019-12-02 10:53:34 -05:00
Tom Rini
1f3813c2ab Merge branch 'master' of git://git.denx.de/u-boot-mips
- MIPS: remove Micronas VCT boards
2019-12-02 10:53:07 -05:00
Daniel Schwierzeck
2a250ae9b6 MIPS: remove Micronas VCT boards
The deadline for migration to CONFIG_DM is v2020.01. The VCT
baords would need an almost complete rewrite of all drivers to
support driver model.

Unless someone has access to the hardware and volunteers to do the migration,
the board should be scheduled for removal.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
2019-11-29 16:18:35 +01:00
Alex Marginean
873d00a3fb configs: ls1028a: enable CMD_DM
Since at least some of the drivers relevant to LS1028A are now following
DM, it's useful to have dm command enabled by default.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-29 10:38:12 +05:30
Priyanka Jain
7a8d9fd73c configs/lx2160a: Add CONFIG_ENV_SECT_SIZE in defconfig
Define CONFIG_ENV_SECT_SIZE as 0x20000 in lx2160a related defconfigs:
lx2160ardb_tfa_defconfig, lx2160ardb_tfa_SECURE_BOOT_defconfig,
lx2160aqds_tfa_defconfig, lx2160aqds_tfa_SECURE_BOOT_defconfig

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-29 10:38:12 +05:30
Tom Rini
c4f697b291 Merge git://git.denx.de/u-boot-usb
- USB keyboard improvements
2019-11-28 07:34:21 -05:00
Tom Rini
29061447a0 - Solve warning for stih410-b2260
- Device tree alignment on v5.4-rc4 for all stm32 boards
 - Correct the eMMC pin configuration on stm32mp157c-ev1
 - Add DFU and SPI-NAND support for stm32mp1 board
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl3dN0YACgkQ4rK92eCq
 k3WlywgAisVONrdkoC345Kq1vQRcKGYxcWVd0IWkuK3QZ4KrMRQrhEqXhmR7OhWD
 4YrAlgV6FEBTlacfKKsxaL7MJ3VK+h5YLvqoGzZS2Inmrx09v6rOofVTRevmB4Qz
 SlIeUKVBijORmRi31I/WcLdiPgd3RR53wQgAugU3PUpuoUb1Z+sJdOreOkl5qGyZ
 8aRgvG/if8afILXfH/a4IUuPboaVjaC5B20JCzX4M4ks8lHJ3atbtawgj/e41yYv
 Ybq3QudM62g4SvTgJ5/1yqjQ4Oj8dkAY7JyAiXfHa9Kip7s16aBDFklDH7eR9v7F
 IxyoYcFhuPADE7ApdWtij/y/KRS66Q==
 =oVPG
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20191126' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm

- Solve warning for stih410-b2260
- Device tree alignment on v5.4-rc4 for all stm32 boards
- Correct the eMMC pin configuration on stm32mp157c-ev1
- Add DFU and SPI-NAND support for stm32mp1 board
2019-11-28 07:33:16 -05:00
Tom Rini
4b39568cfd Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx
- powerpc: Fix DM_MMC related build warnings by adding eSDHC device
  module support for T4240RDB, T2080RDB, T1042D4RDB, T1024RDB, P5040DS,
  P4080DS, P3041DS, P2041RDB, P2020RDB, P1020RDB platforms
2019-11-28 07:32:44 -05:00
Alex Marginean
201d8a5cee configs: ls1028a: enable OF_LIBFDT_OVERLAY
LS1028A QDS board supports multiple combinations of SerDes protocols and
multiple add-on cards with Ethernet PHYs.  Some of them require specific
configuration in Linux DT, and the plan is to use DT overlays for them.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-27 13:12:19 +05:30
Patrick Delaunay
b4fee16108 stm32mp1: add support for virtual partition read
Add read for OTP and PMIC NVM with alternates
on virtual DFU device.

Serie-cc: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-11-26 10:14:35 +01:00
Patrick Delaunay
0df4b94207 stm32mp1: configs: activate CONFIG_MTD_SPI_NAND
Activate the support of SPI NAND in stm32mp1 U-Boot.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-11-26 10:14:35 +01:00
Patrick Delaunay
4edce505f1 stm32mp1: activate DFU support and command MTD
Add support of DFU for MMC, MTD, RAM and MTD command.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-11-26 10:13:45 +01:00
Patrice Chotard
5c347f3398 configs: stih410-b2260: Enable DM_ETH flag
This patch allows to fix the following compilation warning:

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-11-26 10:11:18 +01:00
Tom Rini
4b19b89ca4 - add RPi4 upstream compatible to pinctrl
- fix boot banner on RPi3/4
 - add support for one binary on RPi3/4
 -----BEGIN PGP SIGNATURE-----
 
 iQJGBAABCAAwFiEEUdvKHhzqrUYPB/u8L21+TfbCqH4FAl3a8R4SHG1icnVnZ2Vy
 QHN1c2UuY29tAAoJEC9tfk32wqh+AfQP/iO4qiJWUsY1WgChKl0wZNnkJKViNu6v
 F7zczCIUyI7krdVb3E3PB/ZJwXY/ay1rQeY91cU/9f0Z3yOlsoiwnEfOT/HwwkmD
 KnS6nhisqL0W1yd8sK8XaLOydIFfe05Do1UvF1JhOl3061R81fdruXygkHlgFXiK
 /hrEXLb9l0Zf4XMSD9hQJZiC/K3qeUZV1KsEdSGArjjTj3kivvS++Z0XD1YZsBVs
 rsEl3ZhPeUmzAxmg26IfyJan02NjWY+MyuoSd8QW5kVGsF4WOgvDuBOY1YJ08C/7
 NhLGkub/XhqHVSaMDwiSoX9d2z7ZqTaw7+IZW38+fCMUFAEHiErqMDq+Zfk1DKCd
 WynOzMj6k+Kli+amHQMHuUqIY54XPwpXdn671C7XbQ8xWh7HhWH/sEHP7ekrSV74
 Et7dy5fcleCcrr8EDhdC5iO2fLKhswq4iT0PbnFMtha4jhPqFVHVaAZDacucJ1/V
 JpfYRkLrmEbva3G1emve80tzlDNDxjraX8G6/6trN+F0xjorcbImp64RtRjgdL62
 DwIuba15BGR18LQJY/yHSHT4h3ReEG5qF9vxX+r6vMiFACZbnBPAP/b/REDQ6LWs
 dwW01JQ343dmZiegBQOe98fRDMGhmTd52mAJ/8p60X+byIh5I4XFKCdEdUpSVBpK
 ARrdtg9vtLxv
 =4Z+A
 -----END PGP SIGNATURE-----

Merge tag 'rpi-next-2020.01' of https://github.com/mbgg/u-boot

- add RPi4 upstream compatible to pinctrl
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
2019-11-25 12:56:27 -05:00
Heinrich Schuchardt
dbcbdad92c sandbox: enable USB_KEYBOARD_FN_KEYS
Enable the support of function keys on the USB keyboard. This is necessary
to test the USB keyboard driver.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-11-25 13:28:53 +01:00
Yinbo Zhu
3fca56ee42 configs: enable eSDHC device module for T4240RDB board
Enable eSDHC device module for T4240RDB board

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-25 11:54:28 +05:30
Yinbo Zhu
356152fd94 configs: enable eSDHC device module for T2080RDB board
Enable eSDHC device module for T2080RDB board

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-25 11:54:28 +05:30
Yinbo Zhu
830e46528e configs: enable eSDHC device module for T1042D4RDB board
Enable eSDHC device module for T1042D4RDB board

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-25 11:54:28 +05:30
Yinbo Zhu
26532cab65 configs: enable eSDHC device module for T1024RDB board
Enable eSDHC device module for T1024RDB board

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-25 11:54:28 +05:30
Yinbo Zhu
9eb7ed194d configs: enable eSDHC device module for P5040DS board
Enable eSDHC device module for P5040DS board

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-25 11:54:28 +05:30
Yinbo Zhu
6a41f77e24 configs: enable eSDHC device module for P4080DS board
Enable eSDHC device module for P4080DS board

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-25 11:54:27 +05:30
Yinbo Zhu
2e83e80094 configs: enable eSDHC device module for P3041DS board
Enable eSDHC device module for P3041DS board

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-25 11:54:27 +05:30
Yinbo Zhu
83309ef3d8 configs: enable eSDHC device module for P2041RDB board
Enable eSDHC device module for P2041RDB board

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-25 11:54:27 +05:30
Yinbo Zhu
02504ef07e configs: enable eSDHC device module for P2020RDB board
Enable eSDHC device module for P2020RDB board

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-25 11:54:27 +05:30
Yinbo Zhu
20186d071e configs: enable eSDHC device module for P1020RDB board
Enable eSDHC device module for P1020RDB board

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-25 11:54:27 +05:30
Matthias Brugger
5694090670 ARM: defconfig: add unified config for RPi3 and RPi4
Provide a defconfig which allows us to boot Raspberrry Pi 4
and Raspberry Pi 3 Model B/B+
Instead of using the embedded DTB as done in RPi3 we use the
devicetree provided by the firmware.

Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-11-24 10:46:28 +01:00
Tom Rini
9a0cbae22a Merge tag 'u-boot-rockchip-20191124' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
2019-11-23 20:50:11 -05:00
Jagan Teki
d4fba131bb rock960: Enable USB Gadget
Enable DWC3 core, gadget for rock960 board.

This would help to use fastboot by default.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23 23:41:44 +08:00
Tom Rini
601c2879f8 Pull request for UEFI sub-system for efi-2020-01-rc4 (2)
Use CONFIG_EFI_LOADER=n for ARM11 except for the Raspberry Pi and the
 Raspberry Pi Zero.
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAl3ZPGAACgkQxIHbvCwF
 GsQLxQ/9H4Q/IJE/3beMEn3R5tpiibiflH9Q7DucuQwnHQGaMKkTOSpumK6bIebI
 hCXtCQhChdoogq2W69P/+A98nnp8NbEQ7zQuzjEsn4w74IDoeOEPeGatnpJjRdL9
 3I2b75zPw9w5JYkvEe472nOlX5UWGdzDJ/WtVc7trECr6fmd6MNbEWQv9UpVSbAD
 9fXV3bPA5vFA40VJ16hG5TFbU5D8oSVZ5m+tnpBDsWAdcKf8pZPbICFyczvYWnu9
 HeoZT+HXR/+lcEkO/7v1tZ/PAlnc7sbquzYXOWG0xcQBAqWRRub/dNdV7SN2GVT6
 i2nhNb1Di69QAOWh5V9obqHzdDvlCVCBFjwOr705x+VnRaP+udeNVagT9PcwtrAY
 CzIr7nGqob3b14NYhCDr3EMyKrRogg+0WbnoZHiwCib2vrwwoaEY9c0Yw7GpbLwh
 zk/ysUg8MeHxNhLayBZJJauxbdp2Afe7GTaQDVnxmy3tzfOUnpWW/D9An0EIlXWi
 99h+zPj4RV0v7RzDCDFouX7tq17QgeImulgQI4/HEBhZxwxHEAikGiIJNOmykQo8
 1GQvd4s/zQ0qcI7CKciAyx+mUijLsNBVh8BaeRz+BV6sST16/K81/G4xQMjOg9m5
 OQHiI98j9Wsog8CQJ6d/sldtLCDJa8UIANpLtIOMFNz++BAM2rc=
 =zDGP
 -----END PGP SIGNATURE-----

Merge tag 'efi-2020-01-rc4-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi

Pull request for UEFI sub-system for efi-2020-01-rc4 (2)

Use CONFIG_EFI_LOADER=n for ARM11 except for the Raspberry Pi and the
Raspberry Pi Zero.
2019-11-23 10:20:18 -05:00
Jagan Teki
a9af59a30a fastboot: rockchip: Select FASTBOOT_FLASH[_MMC_DEV]
Select CONFIG_FASTBOOT_FLASH, CONFIG_FASTBOOT_FLASH_MMC_DEV
for rockchip SoC plaforms in fastboot Kconfig file instead
of defined it in board defconfig.

This eventually drop the explicit configs defined in
supporting board defconfig files.

Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23 22:29:49 +08:00
Jagan Teki
132b012ede gadget: rockchip: USB_GADGET_PRODUCT_NUM
Rockchip support differnet or common gadget product number
between Rockchip SoCs like,

0x310a - rk3036
0x320a - rk3229, rk3288
0x330a - rk3328

So, select them on Kconfig based on platform specific
config defined.
   
This eventually drop the explicit configs defined in
supporting board defconfig files.

Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23 22:29:49 +08:00
Jagan Teki
89cbceb388 gadget: Select USB_GADGET_VENDOR_NUM for rockchip
Gadget vendor number, 0x2207 is common across all platfroms
supported in Rockchip SoC.

So, select the same number globally, if ARCH_ROCKCHIP.

This eventually drop the explicit configs defined in supported
board defconfig files.

Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23 22:29:49 +08:00
Jagan Teki
89e311d494 gadget: Select USB_GADGET_MANUFACTURER for rockchip
Select the gadget manufacturer as 'Rockchip' for
all rockchip platform SoC's.

This eventually drop the explicit defined added
on supported board defconfig files.

Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23 22:29:49 +08:00
Kever Yang
5561a9a229 rockchip: lion-rk3368: Migrate to use common FIT generator
The RK3368 lion board ATF can use bl31.elf like RK3399 and get the FIT
source with generic FIT generator script at:
arch/arm/mach-rockchip/make_fit_atf.py

And then we can use 'BL31' environment to get the path of bl31.elf
instead of copy it into U-Boot folder.

CC: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23 22:29:49 +08:00
Kever Yang
65325fba5a rockchip: Convert to use FIT generator for optee
Use generator script so that we can use environment for TEE source.
$TEE for tee.bin, and if file not exist, the script can report a warning,
and meke the build success without a error.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23 22:29:49 +08:00
Heinrich Schuchardt
b7cdecfc19 efi_loader: default EFI_LOADER=n on ARM11
Some of the ARM11 boards have tight limits on the size of U-Boots. Hence
use EFI_LOADER=n as default on ARM11.

Set EFI_LOADER=y for the Raspberry Pi and Raspberry Pi Zero as these boards
have sufficient storage on the SD card.

Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-11-23 09:19:31 +01:00
Tom Rini
47b48fe186 Merge branch 'master' of git://git.denx.de/u-boot-socfpga
- Assorted fixes
2019-11-22 10:41:46 -05:00
Tom Rini
71d96eb99e Merge branch 'master' of git://git.denx.de/u-boot-sh
- Assorted Gen3 fixes
2019-11-22 10:24:14 -05:00
Tom Rini
32a238df79 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-21 08:30:45 -05:00
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Marek Vasut
48f23dd6a4 ARM: socfpga: Fix default mtdparts
The default mtdparts value grew a trailing zero during the Kconfig
conversion. This is because the mtdparts value in the header file
had a \0 at the end, which got misconverted into plain 0 instead of
being dropped.

Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: 43ede0bca7 ("Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT")
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-11-20 23:46:16 +01:00
Ley Foon Tan
086269e17d configs: Stratix10: Disable CONFIG_SPL_USE_TINY_PRINTF
Commit 2a51e16bd5 ("configs: Make USE_TINY_PRINTF depend on SPL||TPL and be default")
enable USE_TINY_PRINTF by default, disable it for Stratix10.

Resync with savedefconfig.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2019-11-20 22:32:00 +01:00
Tom Rini
8d8ee47e03 env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-20 12:24:50 -05:00
Michael Trimarchi
59b01eb7a1 rockchip: dts: tinker: Add tinker-s board support
Support tinker-s board. The board is equivalent of tinker board
except of emmc.

TODO:
- support of usb current burst when the board is powered from pc

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 18:51:25 +08:00
Andy Yan
208b8cd646 rockchip: rk3308: Add support for ROC-RK3308-CC board
ROC-RK3308-CC is a rk3308 based board designed by
Firelfy, with eMMC and 256MB DDR3 and RTL8188 Wifi
on board.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Andy Yan
9e3de722e4 board: rockchip: Add rk3308 evb support
Add support for rk3308 evaluation board.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Vasily Khoruzhick
de43ca7e3e rockchip: rk3399: split rockpro64 out of evb_rk3399
rockpro64 needs to setup I/O domains in order for USB to work in u-boot.
Since we currently don't have a driver to do that, split it into its own
board file and initialize I/O domains here.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Peter Robinson
16359c58e8 rockchip: rk3399: rock960: Update config for TPL
Enable TPL for rock960 like other rk3399 boards.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Jagan Teki
c0828a0156 configs: Rename roc-rk3399-pc -> roc-pc-rk3399 defconfig
roc-rk3399-pc_defconfig is committed in below

commit <8a681f4c5aa15db51ad0209734859c9fe7c29cfd> ("rockchip: rk3399:
Add ROC-RK3399-PC support")

which doesn't follow the existing defconfigs on rk3399.

So, rename as followed with other rk3399 defconfigs.

Cc: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:22:53 +08:00
Heiko Stuebner
deebba82d9 rockchip: add px30-evb board
The px30 evb is an evaluation board for the px30 together with a dsi-
connected display. This adds board and config files for it.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 17:23:26 +08:00
YouMin Chen
ca93e32139 ram: rk3328: use common sdram driver
RK3328 has a similar controller and phy with PX30, so we can use the
common driver for it and remove the duplicate codes.

Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-17 16:23:56 +08:00
Marek Vasut
6da56a11f7 ARM: rmobile: Enable CONFIG_ARCH_FIXUP_FDT_MEMORY on Gen3
Enable CONFIG_ARCH_FIXUP_FDT_MEMORY to let U-Boot patch the
Linux DT memory entries.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-11-15 10:31:54 +01:00
Tom Rini
cb6617a77f defconfigs: Migrate CONFIG_SYS_REDUNDAND_ENVIRONMENT
Move this symbol to Kconfig.  As part of this we can drop a UBI-specific
symbol that was a stop-gap for not having this particular symbol in
Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-12 11:08:00 -05:00
Tom Rini
38d5fa48f4 pfla02: Migrate CONFIG_ENV_IS_IN_SPI_FLASH to defconfig
This board is setting CONFIG_ENV_IS_IN_SPI_FLASH in the header rather
than defconfig, fix.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-12 11:08:00 -05:00
Tom Rini
ba0afaee85 evb-rk3128: Migrate CONFIG_ENV_IS_IN_MMC to defconfig
This board is setting CONFIG_ENV_IS_IN_MMC in the header rather than
defconfig, fix.

Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-12 11:08:00 -05:00
Tom Rini
5f7ff6d63e u-boot-imx-20191105
-------------------
 i.MX8MN SoC support
 ROM API image download support
 i.MX8MM enet enabling
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAl3BmLkPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3oVwL/2Z7kCMCjudXNjXqJFSVsCizuzaxkYvUDQCK
 g8+P7pdci/xZz8pVvVD5zmpZGRM2hu+7hFQwIlSu7anlRqdW+9cZCAJoeq/4A29c
 TkI3w99R0xTDGFlip0zM4vKlQXmC0I0LYbJPVDLjN+zNkhL6QNS3QptONw/3xPzr
 Vj5+eztasl5JOnkTFE8yZkfbkekgPbO4h43oje5XwRdRQcwzo4qEFZcxZzvucz39
 0RXyvu5qtXvSeVYApXeYcnBD3Mn4rjq26rfn2EEntkO0FbhYBHBjwx3/ozmUaOFR
 7AtNyZZSAZFe03egfX6+ODx7tuOTA0PK1LLdogMjLDrOd70px+P7wxY9QZV6hKw9
 TC4YlboZK2bjsPyOwIraTWVUvU9YjQzlPT0SYjyIono33Av1Um7RDvp+XeyG7VPC
 AYE6luZwhauYNUaGegFPexDxOSRqeAiTLx3kOOeHb4Vb4KkJu4Np7Pma2uiqI00V
 4TpWJwhqQPn7lo/N1X9ymBx6iNvt2Q==
 =sgCz
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20191105' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20191105
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
2019-11-12 07:18:23 -05:00
Tom Rini
59e5d1e2a5 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-11 20:04:24 -05:00
Tom Rini
086e391bc4 Merge tag 'u-boot-rockchip-20191110' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
2019-11-11 14:19:32 -05:00
Tom Rini
0b73ef0c02 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- Rename CONFIG_SECURE_BOOT to CONFIG_NXP_ESBC.
- Few bug fixes and updates related to SPI, hwconfig, ethernet,
  fsl-layerscape, pci, icid, PSCI
2019-11-11 14:19:04 -05:00
Kever Yang
f74a089e47 rockchip: firefly-rk3288: Enable TPL support
This patch enable TPL support for firefly-rk3288 board, which works ths
same way with other RK3288 board like Tinker, evb.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-10 20:40:20 +08:00
Kever Yang
006ab58d46 rockchip: rk3399: update SPL_STACK_R_ADDR
Use the same SPL_STACK_R_ADDR in Kconfig instead of each board config;
default to 0x4000000(64MB) instead of 0x80000(512KB) for this address
can support all the SoCs including those may have only 64MB memory, and
also reserve enough space for atf, kernel(in falcon mode) loading.

After the ATF entry move to 0x40000, the stack from 0x80000 may be override
when loading ATF bl31.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-10 20:40:20 +08:00
Kever Yang
4b294886d0 rockchip: evb-px5: defconfig: no need to reserve IRAM for SPL
We use to reserve IRAM to avoid the SPL text overlap with ATF M0 code,
and when we introduce the TPL, the SPL space is in DRAM, we reserve
space to avoid SPL text overlap with ATF bl31.

Now we decide to move ATF entry point to 0x40000 instead of 0x1000,
so that the SPL can have 0x4000 as code size and no need to reserve
space or relocate before loading ATF.

The mainline ATF has update since:
0aad563c rockchip: Update BL31_BASE to 0x40000

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-10 20:40:20 +08:00
Kever Yang
ae2500f89a rockchip: rk3328: defconfig: no need to reserve IRAM for SPL
We use to reserve IRAM to avoid the SPL text overlap with ATF M0 code,
and when we introduce the TPL, the SPL space is in DRAM, we reserve
space to avoid SPL text overlap with ATF bl31.

Now we decide to move ATF entry point to 0x40000 instead of 0x1000,
so that the SPL can have 0x4000 as code size and no need to reserve
space or relocate before loading ATF.

The mainline ATF has update since:
0aad563c rockchip: Update BL31_BASE to 0x40000

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-10 20:40:20 +08:00
Kever Yang
5ce94c74a6 rockchip: rk3399: defconfig: no need to reserve IRAM for SPL
We use to reserve IRAM to avoid the SPL text overlap with ATF M0 code,
and when we introduce the TPL, the SPL space is in DRAM, we reserve
space to avoid SPL text overlap with ATF bl31.

Now we decide to move ATF entry point to 0x40000 instead of 0x1000,
so that the SPL can have 0x4000 as code size and no need to reserve
space or relocate before loading ATF.

The mainline ATF has update since:
0aad563c rockchip: Update BL31_BASE to 0x40000

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-10 20:40:20 +08:00
Andy Yan
a4bbc662fc rockchip: rk3399: Add Leez P710 support
Specification
- Rockchip RK3399
- LPDDR4
- TF sd scard slot
- eMMC
- M.2 B-Key for 4G LTE
- AP6256 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- TYPE-C Power supply

Commit details of rk3399-leez-p710.dts sync from linus tree for Linux 5.4-rc1:
"arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC"
(sha1: 	fc702ed49a8668a17343811ee28214d845bfc5e6)

Signed-off-by: Andy Yan <andyshrk@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-10 20:40:20 +08:00
Tom Rini
ee1c499851 Merge branch '2019-11-07-master-imports'
- Add Phytium Durian Board
- Assorted bugfixes
- Allow for  make ERR_PTR/PTR_ERR architecture specific
2019-11-08 07:27:45 -05:00
Udit Agarwal
bef1845404 freescale/powerpc: Rename the config CONFIG_SECURE_BOOT name
Rename the CONFIG_SECURE_BOOT name to CONFIG_NXP_ESBC to avoid
conflicts with UEFI secure boot.

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-08 16:32:08 +05:30
Udit Agarwal
5536c3c9d0 freescale/layerscape: Rename the config CONFIG_SECURE_BOOT name
Rename CONFIG_SECURE_BOOT to CONFIG_NXP_ESBC to avoid conflict
with UEFI secure boot.

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-08 16:32:08 +05:30
Andrew F. Davis
72077fe160 configs: j721e_evm_r5_defconfig: Remove SPL multi-DTB FIT support
The SPL FIT will only have one DTB, so remove support for multi-DTB. This
also removes an early access to EEPROM used to select the DTB that is not
valid in SPL at the point at which it is accessed, that always returns
false for GP devices and causes a firewall expection on HS.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-11-07 18:39:18 -05:00
Adam Ford
5d44207d17 configs: omap3_logic_somlv: Remove GPIO from SPL
The SPL is too tight, and it cannot start any longer.  To
help reduce the size of SPL, we need to remove some non-critical
features.

This patch removes SPL_GPIO_SUPPORT to free up some operating space.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-11-07 18:39:18 -05:00
Adam Ford
88279e1b0f Revert "ARM: omap3_logic/omap35_logic: Enable GPIO in SPL"
The SPL is too tight, and it cannot start any longer.  To
help reduce the size of SPL, we need to remove some non-critical
features.

This reverts commit 66063a7c13.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-11-07 18:39:18 -05:00
Keerthy
14dfca69d7 configs: j721e_evm_r5_defconfig: Enable AVS Class 0 & dependent configs
Enable AVS Class 0 & dependent config options.

Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07 18:39:17 -05:00
Tero Kristo
b31e650867 configs: am65x_evm_r5_defconfig: Enable AVS class 0 support
Enable AVS class 0 support for the R5 SPL bootloader.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07 18:39:17 -05:00
Tero Kristo
e41dd6c499 configs: am65x_evm_r5_defconfig: Enable TPS62363 regulator support
TPS62363 is used to control the MPU_VDD voltage, so enable the driver
for this.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07 18:39:17 -05:00
liu hao
e3aafef4cf arm: add initial support for the Phytium Durian Board
This adds platform code and the device tree for the Phytium Durian Board.
The initial support comprises the UART and the PCIE.

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>

Signed-off-by: Steven Hao <liuhao@phytium.com.cn>
2019-11-07 18:01:13 -05:00
Tom Rini
0be2ecd486 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-07 17:58:06 -05:00
Heiko Schocher
2a51fe01be mpc85xx, socrates: add DM PCI support
add DM PCI support on the socrates board.
use PCIE_FSL now.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-06 16:30:19 +05:30
Heiko Schocher
98beb60a2a mpc85xx, socrates: enable DM serial
switch to DM_SERIAL support.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-06 16:30:19 +05:30
Heiko Schocher
92746bac88 mpc85xx, socrates: enable DM I2C
enable DM I2C support for the socrates board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-06 16:30:19 +05:30
Heiko Schocher
4c65a449ae mpc85xx, socrates: disable VIDEO
disable video, as not really needed longer.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-06 16:30:19 +05:30
Heiko Schocher
a9c909d9e0 mpc85xx, socrates: get rid of DM_USB warning
add some defines and get rid of USB warning.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-06 16:30:19 +05:30
Heiko Schocher
39642abf56 mpc85xx, socrates: add DM support
enable CONFIG_DM for the socrates board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-06 16:30:19 +05:30
Peng Fan
bdcf3a88cc imx: imx8mm-evk: enable ethernet
add phy-reset-gpios to reset phy
Add board_phy_config to configure phy
Enable DM_ETH

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-05 10:27:18 +01:00
Peng Fan
d239d9d946 imx: add i.MX8MN DDR4 board support
Support pinctrl/clk/sdhc, include ddr4 timing data.

Log:
U-Boot SPL 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800)
Normal Boot
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0

U-Boot 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800)

CPU:   Freescale i.MX8MNano rev1.0 at 24 MHz
Reset cause: POR
Model: NXP i.MX8MNano DDR4 EVK board
DRAM:  2 GiB
MMC:   FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-05 10:27:18 +01:00
Peng Fan
84abc8d533 imx8qm: mek: enable dm-spl for pm
with u-boot,dm-spl added for imx8qm-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.

Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-05 10:27:18 +01:00
Simon Glass
e9bae5c534 mx6: tbs2910: Minimise libfdt code size
This board appears to be very near its size limit and cannot accept the
new checking code in libfdt. Disable this code so this the board can
continue to build.

Signed-off-by: Simon Glass <sjg@chromium.org>
2019-11-04 18:15:32 -07:00
Tom Rini
73b6e6ad25 u-boot-imx-20191104
-------------------
 
 - i.MX NAND: nandbcb support for MX6UL / i.MX7
 - i.MX8: support for HAB
 - Convert to DM (opos6ul, mccmon6)
 - Toradex i.MX6ull colibri
 - sync DTS with kernel
 
 Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/606853416
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAl2/6YYPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3qSAL/37iSxotpJEcvCcAg0x96n6na/O0SjT3NkoT
 glPaFXLkzR7hbK5yR3g2P0LuNGRGkCQbuz61Hn4wNLRySVodvIJ1pUITu9GaLnex
 graG/ssqdPMEWU0LDoatr/fgoCQo7DEKOuzRmvHAYus7LZJ6edctOyTXuiMhPZ+T
 DJ51RAUq11CleuA8nnz/iV2WCR8pw9sPS7P016lrDF+sWLIqm+/UMnwiIUV4KVhI
 og/fevJfE52vOdV1the6xgpffQGICckNUFREgXaPo3JsP67icPiUGQ4RiFhHp+ff
 rNyMdD/g6YZOoMoWda989h0l3gBwKjBQ9eGG05V8GEmyxzzkOGa5So2O9NzG90CQ
 vcOlEsC/siNZ87B5VkVkWjmrEnHcICtAFJSSntC7pLxtQMMqMbioRe5w+zmSrWeH
 GYh9cxe3ABLYBxISrT6BTfyXs0cD5tMl6D9snLaGyUzHcH2AGkVTkVabemuMSpIZ
 kBzNRFmx3+3Ync+CoaLA+G1YRXmgSw==
 =zlN+
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20191104' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20191104
-------------------

- i.MX NAND: nandbcb support for MX6UL / i.MX7
- i.MX8: support for HAB
- Convert to DM (opos6ul, mccmon6)
- Toradex i.MX6ull colibri
- sync DTS with kernel

Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/606853416
2019-11-04 12:57:41 -05:00
Tom Rini
9c17ad33fe tbs2910: Disable Plan9/RTEMS bootm support
We have once again reached a point where this board does not build in
some cases with supported toolchains due to reaching a size constraint.
To regain some space, disable support for Plan 9 / RTEMS images with the
bootm command.

Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-03 19:28:37 -05:00
Tom Rini
b947dd8fc6 tbs2910: Disable Plan9/RTEMS bootm support
We have once again reached a point where this board does not build in
some cases with supported toolchains due to reaching a size constraint.
To regain some space, disable support for Plan 9 / RTEMS images with the
bootm command.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2019-11-03 21:18:00 +01:00
Oliver Graute
eef72440db imx: support i.MX8QM ROM 7720 a1 board
Add i.MX8QM ROM 7720a1 board support

Boot log as below:
U-Boot 2019.10-rc3-00004-gd073e0242f (Sep 20 2019 - 08:24:13 +0200)

CPU:   NXP i.MX8QM RevB A53 at 1200 MHz

Model: Advantech iMX8QM Qseven series
Board: ROM-7720-A1 4GB
Build: SCFW 65afe5f6
Boot:  SD2
DRAM:  4 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In:    serial@5a060000
Out:   serial@5a060000
Err:   serial@5a060000
Net:   eth0: ethernet@5b040000Could not get PHY for FEC1: addr 1
, eth-1: ethernet@5b050000
Hit any key to stop autoboot:  0

Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
2019-11-03 21:18:00 +01:00
Hannes Schmelzer
c04ac5bd40 board/BuR/brppt2: initial commit
This commit adds support for the brppt2 board. The board is based on the
i.mx6 dual-lite SoC.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-11-03 21:17:55 +01:00
Peng Fan
8c61eba03d imx8mm: evk: enable bd71837 pmic
Enable bd71837 pmic for i.MX8MM EVK board, need to set voltage for
DRAM and linux suspend voltage requirement.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03 17:04:16 +01:00
Sébastien Szymanski
b1be79b417 opos6uldev: migrate to DM_VIDEO
Migrate to DM_VIDEO, update the device tree and remove code that is no
longer necessary.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-11-03 17:04:16 +01:00
Sébastien Szymanski
b72dd938ec imx6ul: opos6ul: migrate to DM_ETH
Migrate to DM_ETH and remove code that is no longer necessary.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-11-03 17:04:16 +01:00
Patrick Wildt
05737f3585 imx: update i.MX8MQ device trees
This updates the i.MX8MQ device trees and, necessarily, also the
i.MX8MQ clock bindings.  These are taken verbatim from from the
Linux kernel version v5.4-rc2, which three small changes which
were already part of the previous device tree:

 * Keep the PSCI reserved memory range
 * Keep the alias for ethernet, so that the MAC address can be set
 * Keep the modified #include for the IOMUXC pins

Signed-off-by: Patrick Wildt <patrick@blueri.se>
Acked-by: Peng Fan <peng.fan@nxp.com>
2019-11-03 17:04:16 +01:00
Lukasz Majewski
c4cb27e59f mccmon6: defconfig: nor: Enable usage of *_TINY_* drivers in SPL
After this change the SPL size has been reduced from 38K to 34K.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03 17:04:16 +01:00
Lukasz Majewski
e4417ed03e ARM: imx: Convert mccmon6 to use fitImage instead of uImage+DTB
This commit enabled support for fitImage on mccmon6 when we
switch to DT/DTS (including falcon mode).

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03 17:04:16 +01:00
Lukasz Majewski
8e64181a99 ARM: imx: Convert mccmon6 to use DM/DTS in the u-boot proper
This commit converts mccmon6's u-boot proper (in a single commit to avoid
build breaks) to use solely DM/DTS.

The DTS description of the mccmon6 has been ported from Linux kernel
(v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be)

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03 17:04:16 +01:00
Lukasz Majewski
f6a4df3846 imx: Enable RTC (ds1307) support in the U-Boot proper on TPC70 board
The TPC70 is equipped with DS1307 RTC device. Add code to enable support
for it.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03 17:04:16 +01:00
Claudius Heine
cd71c7597a ARM: imx6: DHCOM i.MX6 PDK: defconfig: Enable MMC support of SPL
Signed-off-by: Claudius Heine <ch@denx.de>
2019-11-03 17:04:16 +01:00
Lukasz Majewski
3201e5b444 imx: defconfig: Enable CONFIG_SPL_FORCE_MMC_BOOT on display5
After the following commit:
commit 772b55723b ("imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC
boot on falcon mode")
it is possible to set the CONFIG_SPL_FORCE_MMC_BOOT flag, which allows
using MMC device as boot device regardless of the device used by Boot ROM
(FBL) as the first boot medium.

Display5 board needs this flag set to allow falcon boot from eMMC device.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03 17:04:16 +01:00
Eugeniy Paltsev
43f3031313 ARC: [plat-axs101]: migrate to DM_MMC
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2019-11-01 16:45:40 +03:00
Alexey Brodkin
0da32633ab arc: emsdp/iotdk: Switch to DM_MMC
Somehow EMSDP & IoT DK boards were skipped on ARC boads conversion
to DM MMC. So doing it now.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2019-11-01 16:45:40 +03:00
Alexey Brodkin
9f353ad88a arc: emsdp: Increase max FAT cluster size
Some especially large SD-cards come from stock formatted with
larger FAT cluster size so to accommodate those we just increase
what we expect to have here in U-Boot given we have a plenty of
space on EM SDP (16 MiB).

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2019-11-01 16:45:39 +03:00
Tom Rini
cc64810dc6 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sunxi
- H6 dts(i) sync (Clément)
- H6 PIO (Icenowy)
- Fix pll1 clock calculation (Stefan)
- H6 dram, half DQ (Jernej)
- A64 OLinuXino eMMC (Sunil)
2019-10-30 09:04:52 -04:00
Tom Rini
ffc379b42c - bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
 - mtmips: add new drivers for clock, reset-controller and pinctrl
 - mtmips: add support for high speed UART
 - mtmips: update/enhance drivers for SPI and ethernet
 - mtmips: add support for MMC
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAl2zFisACgkQKPlOlyTy
 XBgf9RAAkNwLjqUcBz3Ob1briRG5HF4D6bZCpjtkTIO8a2fanUHbSehh30TX8x2X
 z0t/9Sd4OZwAeTxfQ/AlbbVdiB9IMgEb6lJ30Vr88MRNoPhABIQ8hw5xAzFi/6x9
 88YolS/HQo6iR9rzSlaKjdIHhPTH5oQzRJ3JLqSwZzfUNy+zqINEhs3SYCnD2lyV
 gTgiIT3Y5nKrhVHPUCy+jQG+wwWej2NFgwn71vR3/PSQJwxBuasg0qqOKD9hRtpC
 XL6VErE7bf00elO8xjEObYrmB2FpffXJdkazS2HtRYNyKx0quaRNXJt7wqxEVP9L
 M6SmL+S7zBFAetc/iyrlaakPvn7ImehSZkgLYaTPc3yzO+6bgq9tLfBERn/B/s5g
 YyIzPGF66L96nuu0eVGCgSoUBjzBE8l2QTI8dho5xJxjWAUJOWSB0egqfFZzYVFu
 4X37w6Z0j6uTK2oEl7KgJdc0JsZRsAJ8ZiqgOeNeMUTl2RnjGt0Oa7E24Va3n3hM
 5vuEba9nPUFmdC5vlSd2RUK/dB587uKV93r5j54U62clpbiK+VMaRuRVX64ytZvB
 B/0fKyCu+y7bxeZe4/X27jBUOk5yCuxbNI66m+cnnvfHqEmhz5PfDCEK1Dr29oqf
 sCJLgTr7ahyuW4kEoL7KCOBEugPI85fp8/OlqC63M6/Kft0w5sA=
 =6G/J
 -----END PGP SIGNATURE-----

Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mips

- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
2019-10-25 20:07:24 -04:00
Tom Rini
15147dc6a9 Merge branch '2019-10-24-ti-imports'
- Enable DFU on dra7xx boards
- Further Keystone 3 platform improvements
2019-10-25 17:33:28 -04:00
Faiz Abbas
18df182b63 configs: dra7xx_evm: Increase the size of SPL_MULTI_DTB_FIT
Expand SPL_MULTI_DTB_FIT to accommodate usb peripheral nodes being
added to support SPL_DFU bootmode.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-25 17:33:21 -04:00
Faiz Abbas
add2242c49 configs: dra7xx_evm: Add Kconfigs for SPL_DFU bootmode
Enable configs for supporting SPL_DFU bootmode.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-25 17:33:21 -04:00
Tom Rini
271103ac0b Merge branch 'master' of git://git.denx.de/u-boot-usb
- DWC3 improvements
- i.MX7 EHCI bugfix
2019-10-25 13:50:51 -04:00
Tom Rini
c9e50bb12a Second set of u-boot-atmel features and fixes for 2020.01 cycle
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJdspnqAAoJEB6zHgIOrC/Ixi4IAJEEiCZPu6Z3fbkFX/Um7vCX
 eMTltJN8nz4oiSi3xdx3ejueqWdW3F8VuCkHb0j0bVAhMlUlVgwCzfd0cD+D2iwS
 jkrgzASNAr+JeYKYEdWqqfaUxOCd2qfuBu9EXlpvKQLWLt+KRfsOsHWcgR4bf095
 aGCihvd/fKhKYUvbf5cEQnsWa3UwtsKk4Web5MKjxXx3p0iVNlu4KLd/vDWfTios
 X1NqiO5ZjXNrDxyG6Aj8lgDXlE5kfeKaN/aCJU1/0U2cXm8JRu2w2dv1P/e/kU+j
 NHIGzICAG4Lk/4gQTeuohJxLyvj7K3i1H12ik9Qeh4H1/5fsyybyltGUo7H443s=
 =JYe3
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-atmel-2020.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel

Second set of u-boot-atmel features and fixes for 2020.01 cycle

This feature set includes Eugen's work on a new tiny flexcom driver and
eeprom mac retrieval for the sam9x60-ek board.
2019-10-25 13:50:33 -04:00
Tom Rini
e382713d22 Xilinx/FPGA changes for v2020.01 part 2
common:
 - Fix manual relocation for repeatable commands
 
 arm:
 - Also clean up generated dtbos
 
 microblaze:
 - Add support for Manual relocation in crypto framework
 - Tune and align architecture bootm support
 
 zynq:
 - DT sync ups
 - Some defconfig updates
 - Remove empty board_early_init_f()
 
 zynqmp:
 - Clean firmware handing via drivers/firmware/
 - DT/defconfig name alignments
 - DT cleanups with using firmware based clock driver
 - Some defconfig updates
 - Add IIO ina226 DT description
 - Tune zynqmp_psu_init_minimalize.sh script
 - Add single nand mini configuration, e-a2197, m-a2197-02/03 and zcu216
 
 versal:
 - Clean firmware handing via drivers/firmware/
 - Add gpio support
 - Enable DT overlay/USB/CLK/FPGA
 - DT updates
 - Tune mini configuration
 
 spi:
 - gqspi - Remove unused headers
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXbKa4QAKCRDKSWXLKUoM
 ISzJAJ0YpGS7HziGFVRBlcsyRH8QlWCqOQCfb0jIWzhL8pvj9TA01CdU0Axdbwk=
 =GIpp
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2020.01-part2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx/FPGA changes for v2020.01 part 2

common:
- Fix manual relocation for repeatable commands

arm:
- Also clean up generated dtbos

microblaze:
- Add support for Manual relocation in crypto framework
- Tune and align architecture bootm support

zynq:
- DT sync ups
- Some defconfig updates
- Remove empty board_early_init_f()

zynqmp:
- Clean firmware handing via drivers/firmware/
- DT/defconfig name alignments
- DT cleanups with using firmware based clock driver
- Some defconfig updates
- Add IIO ina226 DT description
- Tune zynqmp_psu_init_minimalize.sh script
- Add single nand mini configuration, e-a2197, m-a2197-02/03 and zcu216

versal:
- Clean firmware handing via drivers/firmware/
- Add gpio support
- Enable DT overlay/USB/CLK/FPGA
- DT updates
- Tune mini configuration

spi:
- gqspi - Remove unused headers
2019-10-25 11:23:46 -04:00
Weijie Gao
ec54c8c000 configs: mtmips: remove configs which are selected in Kconfig or useless
Some configs are selected in Kconfig and is no longer needed in the
defconfig files. Some configs (power domain, ram) are never used.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Álvaro Fernández Rojas
331bee8786 bmips: enable vr-3032u nand support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25 17:20:43 +02:00
Sunil Mohan Adapa
4ed293ae79 arm64: dts: sun50i: Add support for A64 OLinuXino (with eMMC)
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.

The Linux kernel upstream has chosen to create and use a separate device tree
for the eMMC variants instead of adding eMMC support existing device tree. These
changes to Linux kernel are queued for Linux 5.4.

commit <02bb66b347ff8115f53948f86b884e008ba385b9> ("arm64: dts:
allwinner: a64: Add A64 OlinuXino board (with eMMC)")

This patch has been tested on A64-OLinuXino-1Ge16GW and is based on Linux
device-tree and a64-olinuxino_defconfig.

Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
[jagan: updated linux-next commit details]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 14:15:49 +05:30
Frieder Schrempf
832ce20278 mtd: spi: Clean up usage of CONFIG_SPI_FLASH_MTD
Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.

Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).

We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.

We do this all in one patch to guarantee bisectibility.

This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:32 +05:30
Frieder Schrempf
a9ec8423a9 stm32mp1: configs: Add CONFIG_SPL_SPI_FLASH_MTD
As SPI_FLASH_MTD is used in SPL and U-Boot proper, we enable both,
now that a separate option for SPL was introduced.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
[jagan: drop unrelated change]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:32 +05:30
Jagan Teki
f8cb77ffba configs: sopine-baseboard: Enable SPI-FLASH
SoPine has winbond SPI-FLASH, so enable the same in defconfig
and add aliases for spi0 in -u-boot.dtsi

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:31 +05:30
Tom Rini
17fd9915a4 Merge branch '2019-10-24-UFS-support'
- Add Universal Flash Storage (UFS) support
2019-10-24 09:51:48 -04:00
Michal Simek
6bf27ed9ae arm64: zynqmp: Add support for e-a2197-00 System Controller
Add support for System Controller available on e-a2197-00 base board.
System is very similar to p-a2197-00 board.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:03 +02:00
Michal Simek
19096aba4f arm64: zynqmp: Enables SPI_FLASH_BAR
Enable the SPI flash Bank/Extended address register support for all ZynqMP
boards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:03 +02:00
Michal Simek
7e856eff20 ARM: zynq: Disable fdt and evn exist for cse_qspi
Mini u-boot should be really small that's why it is necessary to disable
all unneeded configs.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:03 +02:00
Michal Simek
3e5476c6cd ARM: zynq: Remove unused board_early_init_f()
board_early_init_f added by commit e6cc3b25d7
("arm: zynq: Wire watchdog internals") is no longer needed that's why
remove it also with Kconfig enabling.

Fixes: ccd063e981 ("watchdog: Move watchdog_dev to data section (BSS may not be cleared)")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:03 +02:00
Michal Simek
2ce5641df0 ARM: zynq: Dont use 4K sector size support for mini qspi configuration
This patch removes 4K sector size support for Zynq mini qspi configuration
in favour of fast erase speed.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:03 +02:00
Siva Durga Prasad Paladugu
542ff688ed arm64: zynqmp: Dont use 4K sector size support for mini qspi configuration
This patch removes 4K sector size support for ZynqMP mini qspi
configuration in favour of fast erase speed.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:03 +02:00
Siva Durga Prasad Paladugu
6452fb36a4 arm64: zynqmp: Enable Micrel phy support for xilinx zc1275 revB
This patch enables Micrel phy support for Xilinx ZynqMP zc1275
revB board.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:03 +02:00
Michal Simek
9a133f6fae arm64: versal: Enable BDI for mini mtest configuration
bdi is useful to see how memory is mapped.
Also enable 3 memory banks to be mapped.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:03 +02:00
Michal Simek
dd7a3291cc arm64: zynqmp: Add support for zcu216
zcu104/6 defconfig was used as source. Standard features are enabled.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:03 +02:00
Michal Simek
3d5c9060c5 arm64: zynqmp: Add support for m-a2197-03
It is based on m-a2197-01 with some changes in i2c intrastructure.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:03 +02:00
Michal Simek
137c4aef0c arm64: zynqmp: Add support for m-a2197-02
It is based on m-a2197-01 with some changes in i2c intrastructure.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:03 +02:00
T Karthik Reddy
bf60910025 zynqmp: configs: Add single nand flash mini u-boot configuration
This patch adds configuration for single nand flash mini u-boot.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Siva Durga Prasad Paladugu
5b3b7553bf arm64: versal: Enable UHS support
This patch enables UHS support for Versal platforms.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Siva Durga Prasad Paladugu
24844d3f94 arm64: versal: Enable bit stream loading support for versal platform.
This patch enables bitstream loading support for Versal platform.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Siva Durga Prasad Paladugu
b1255bc09e arm64: versal: Update boot delay to perform autoboot
Update boot delay to 5 for performing autoboot.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Siva Durga Prasad Paladugu
1db38eef0e arm64: versal: Increase SYS_MALLOC_F_LEN
This patch increases SYS_MALLOC_F_LEN as the versal clock
driver needs to be probed before relocation itself inorder
to get required clocks before relocation.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Siva Durga Prasad Paladugu
6ac3cf090d arm64: versal: Enable CLK command
Enables clock command for dumping clocks.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Michal Simek
32669c816e arm64: versal: Enable USB driver support
This patch adds usb host and device mode support for Xilinx
Versal virtual platform. By default USB host functionality
is enabled. To use in usb device mode, set dr_mode property
in DT to peripheral.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Michal Simek
0c92d3aed2 arm64: versal: Enable LIBFDT_OVERLAY
Enable device tree overlay to build all dtbs for Versal with -@ flag to
enable applying overlays.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Michal Simek
50d9283347 arm64: zynqmp: Sync names for SC with Versal
ZynqMP based System controller is present on Versal boards. This patch is
aligning names with Versal to follow the spec.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:01 +02:00
Michal Simek
c4690c54b7 ARM: zynq: Move BOOTM_NETBSD to Kconfig
The commit 4b0bcfa7c4 ("Kconfig: Migrate CONFIG_BOOTM_* options")
moved BOOTM_ options to Kconfig that's why align zynq defconfig with it.

Disabling NETBSD was done by commit d6f48ea5ce
("ARM: zynq: Do not enable NETBSD support by default").

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:01 +02:00
Michal Simek
96e8e52bb8 arm64: versal: Enable GPIO command for Versal
Enable GPIO command for Xilinx Versal platform. Driver is updated that's
why it can be used directly. Driver is enabled by default through Kconfig.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:01 +02:00
Tom Rini
c9e40996f9 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
- Add support for HyperBus Memory Controller of TI's J721e
  and AM654 SoCs (Vignesh)
2019-10-24 07:32:21 -04:00
Eugen Hristev
47079f6fcb configs: sam9x60ek: enable microchip_flexcom, i2c and eeprom
enable driver model for i2c, eeprom for mac retrieval from eeprom i2c memory,
and microchip_flexcom driver.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-24 13:01:57 +03:00
Jean-Jacques Hiblot
733ff952c3 configs: sei610: khadas-vim3 : disable Gadget support for the DWC3
Those platform use the DWC2 controller for the gadget support and the
DWC3 for host-only operations.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-24 11:28:19 +02:00
Jean-Jacques Hiblot
2e1d8cfaf1 configs: k2g_evm_defconfig: disable XHCI_DWC3 and enable KEYSTONE_USB_PHY
KEYSTONE_USB_PHY is now required for proper USB operations.
XHCI_DWC3 can be disabled as the xhci-dwc3 is not used anymore
USB_DWC3_GADGET can also be removed, it is now selected automatically.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-24 11:28:17 +02:00
Jean-Jacques Hiblot
3e6ab7327f usb: dwc3: Kconfig: get rid of obsolete mode selection
The mode selection for the DWC3 is kind of obsolete. The driver does not
have to be host only or gadget only. This choice is confusing.
All the remaining callers of dwc3_uboot_init() explicitly set dr_mode
before calling the function, so none rely on a default behavior.

Remove the choice menu and keep only the USB_DWC3_GADGET option. Enable it
by default if USB_GADGET and USB_DWC3 are enabled.
It must be disabled for the evb-rk3328 as it uses DWC2 for the gadget and
DWC3 for the host.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-24 11:28:17 +02:00
Jean-Jacques Hiblot
a8973731a4 usb: host: remove the xhci-zynqmp driver
This driver is not used anymore.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-24 11:28:16 +02:00
Vignesh Raghavendra
a360e42216 configs: j721e_evm_a72_defconfig: Add HBMC related configs
Enable HBMC and HyperFlash in A72 SPL and A72 U-Boot

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2019-10-24 09:49:32 +02:00
Faiz Abbas
c6ffc0d62f configs: j721e_evm_a72: Enable configs for UFS
Enable SCSI and UFS related configs.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23 20:47:12 -04:00
Patrice Chotard
b7fe6fd01f configs: stm32h743-eval: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-10-22 10:56:32 +02:00
Patrice Chotard
5413b33afd configs: stm32h743-disco: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-10-22 10:56:32 +02:00
Patrice Chotard
e15ed9e436 configs: stm32f469-discovery: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-10-22 10:56:32 +02:00
Patrice Chotard
fd697a63e2 configs: stm32f429-evaluation: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-10-22 10:56:32 +02:00
Patrice Chotard
6600859eae configs: stm32f429-discovery: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-10-22 10:56:32 +02:00
Tom Rini
4b5c4dd93a Pull request for UEFI sub-system for efi-2020-01-rc1 (2)
Install the simple file protocol only if there is a file system on the
 partition.
 
 Enable CONFIG_CMD_NVEDIT_EFI on QEMU.
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAl2p9OcACgkQxIHbvCwF
 GsRLAg//fmqk3B7FInPfQ6fxfyMx3Ck2EosoePjf0IsMq0nfGIVMigXZwpUtwkwN
 LBmp/Vf8mkRfFNWk55/qzecdgCoVKx1nN1YoqsGh/ZFsX+1L3Kd01ODJw0in0T8N
 GwMm0sbSk+EqWp4JMs9seZBL5S1PfCZ59rzRcvgLq+9VgZX9+LxLeIidZ3bh/++w
 1fo5jZtWavKNuCqgU9cUlT2FLgE+8q+W1ZAVmD1fDs3ef7Xys8UaTOP3M9jtT9AS
 ruletzPRmJ1GFe9xC94qIfij4ZXclo2tt7L3c6QeTpiwcav5HFiQIsRvvssnRpma
 GYZyyu2CNgjChjqOvGMFftWvR3kZWUHCEFFxZzH+0YfdcU1MNfwtQjieviuJGc5S
 sOK/SWvsdEoHow85NNAmDDJUcR1MfakMjFyM+fcs/YtUoJHoP6LKQwAmJMpMLPq4
 6164ymvdoo8YD3cYLP9yvsJ+r9GW3FNUloBwAwz3OMJy1uXoi1igMv60dMBCLJDC
 cftW48sFivg0oSb+780xiJwyjjreg9dRqmlp0lhsxuGDPA2YqxNiAZs/Q2geEM3+
 LJmeB78PvGAuzU1LPW34IsYyplRa21y1y+IbOceRdcbOmY6XT8Zf9eMInKdoE78i
 gal2rjNdHoGX8v5WchUNNmIVjQQqDMf1jOi/lfkeivKu16/68HY=
 =X+Tw
 -----END PGP SIGNATURE-----

Merge tag 'efi-2020-01-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi

Pull request for UEFI sub-system for efi-2020-01-rc1 (2)

Install the simple file protocol only if there is a file system on the
partition.

Enable CONFIG_CMD_NVEDIT_EFI on QEMU.
2019-10-18 16:37:03 -04:00
Guillaume La Roque
be2ffa1656 configs: sei610: Add config file to fix userdata size
Add separate config file to handle the different eMMC size on
the sei610 board.

Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18 14:54:37 +02:00
Neil Armstrong
b8ada582cf boards: amlogic: add SEI610 support
Add support for the customer board SEI610 manufactured by SEI Robotics
with the following specifications:
 - Amlogic S905X3 ARM Cortex-A55 quad-core SoC
 - 2GB DDR4 SDRAM
 - 10/100 Ethernet (Internal PHY)
 - 1 x USB 3.0 Host
 - 1 x USB Type-C DRD
 - 1 x FTDI USB Serial Debug Interface
 - eMMC
 - SDcard
 - Infrared receiver
 - SDIO WiFi Module

Like it's SEI510 counterpart, the boot flow is designed to boot
Android AOSP built for the Yukawa Android device.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18 14:47:00 +02:00
Neil Armstrong
4e67af4620 configs: sei510: enable everything-else power domain
The GX VPU Power Domain driver has been replaced by the Everything-Else
Power Domain driver for G12A and SM1.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18 14:36:16 +02:00
Andreas Färber
30b8c2b6cf configs: Add Khadas VIM3 defconfig
Derived from odroid-n2_defconfig and README.odroid-n2.

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18 11:59:44 +02:00
Neil Armstrong
3b12fecebd configs: sei510: enable Video Display support
Add the necessary config options to support BMP display over HDMI,
and add a preboot command to load the BMP file from a predefined
eMMC partition.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-18 11:54:22 +02:00
Heinrich Schuchardt
5cc349bb09 efi_loader: enable CONFIG_CMD_NVEDIT_EFI on QEMU
To reduce the default image size CONFIG_CMD_NVEDIT_EFI was disabled by
default. Re-enable it on the QEMU platforms supporting the UEFI sub-system.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-10-17 19:19:56 +02:00
Tom Rini
c83b1bb923 binman enhancements:
- Dropping some test Elf files and building them from source instead
 - Refactoring of x86 16-bit entries
 - Support for SPL symbols within sections
 - Handle the 'notes' sections and hidden symbols in recent binutils
 - Improved error reporting with a tool fails
 
 libfdt and documentation fixes
 vboot required-key test
 driver model power-domain controls
 patman Message-Id enhancement
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl2l20YACgkQfxc6PpAI
 reZQQQgA0zxySnZR6IuTr+MXJP019SjU0T/rj2Ob77ODhLTtLtE3aFYgBIsyyOyr
 /NZ6V7wPhCfGGBGWdPzYdOUIkG5L4O+1zrwWGgVJCAAaCaDlJVIXmljJ667SE9ps
 9jfJW/nkzgsa/cOweOUJF3vBUKnDN1pv9aTXwAXttzv/OqaZ1AaUObnmeZ9fzr65
 mXjR7/eLYx26KQ8IEo8hhgdFhN/d/aUtSCYPWASqtcI9TLg8A5gmtNxy83+w8gzC
 kFIr7c0QjZ3EQHLyD4/MAcGvhZZMBPbV6dyIO19hUS80S1l1yMTd72iTYuvG8bAt
 5TzlQCSqvGryF6TRxVn8GPr2/T0v/A==
 =Oo/D
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-15oct19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm

binman enhancements:
- Dropping some test Elf files and building them from source instead
- Refactoring of x86 16-bit entries
- Support for SPL symbols within sections
- Handle the 'notes' sections and hidden symbols in recent binutils
- Improved error reporting with a tool fails

libfdt and documentation fixes
vboot required-key test
driver model power-domain controls
patman Message-Id enhancement
2019-10-16 18:10:31 -04:00
Heinrich Schuchardt
cb578f0a87 arm: remove the H2200 board
U-Boot cannot be built for h2200_defconfig with CONFIG_DM=y.

The maintainer Lukasz Dalek suggested to remove the board.
https://lists.denx.de/pipermail/u-boot/2019-August/380685.html

Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[trini: As this is the last non-toradex PXA board, update travis too]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-16 18:09:08 -04:00
Philippe Reynes
5fff9b3bc9 sandbox64: enable command aes
This commit add the support of command aes.
Then, it may be used on pytest.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-10-15 08:40:03 -06:00
Philippe Reynes
8d69439550 sandbox: enable command aes
This commit enable the command aes on sandbox.
Then, it may be used on pytest.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-10-15 08:40:03 -06:00
Tom Rini
6891152a45 Merge branch 'master' of git://git.denx.de/u-boot-socfpga
- vining_fpga updates
2019-10-14 21:00:10 -04:00
Tom Rini
6f1f28b8e1 u-boot-imx-20191014
-------------------
 
 Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
 
 	- logicpd pinmux
 	- i.MX7ULP: imx_ddr_size
 	- fixes Toradex i.MX6/i.MX7
 	- pico-imx7d
 	- tpc70 converted to DM
 	- New Board: meerkat96
 	- add HAB version command
 	- i.MX8 :
       		imx8: Jump from alias to OCRAM address at SPL init
       		imx8qm/qxp: Set SPL TEXT base to OCRAM base
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAl2kbrYPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et30iQL/RDCe3R1MuQPQdjBEUcb+ZXP8/vaAAbgAsv6
 MNN/ybJ8pIXGVF5qxJxzZgMcUvIq1vy8romomIwVBOr7gueoYMokpKeE95P4XK2r
 HmFM+/ZcXIXvDrHrULDquAvCG6zhOMHXdbmWcQcZLcHSCsZpkh4YuuGzFVpxTgNE
 kTJpEF+Orw49w9wMVKeqfv9z3MsYkr/vV3kH/+ISndN6cOBOjV56Qzl/hlzxiN1d
 wueTQi1pxUVjbsKWIkf76XTeSa5621bM01+YMN3CFq/AWhVMbpnaWWGB6ET4NBjD
 k/BjRgCZ+/hwjpHnbylHEmsLolNsIXn8KirE73OCmIvov/vUYaaZJ5lBzU+L2A5k
 tK6p1LOTvsRxKBsN49hQIQLJMcn/sp9RpP9ohgCs3lj7bKGAQ1HoxqylypeDGPv1
 htKGdBFGiEfoCus1Ob7NAevYAPlVM7h+mDzFSYhlr9BZnrDj2V3nwICj8KV3wkwl
 lPiUQiYMUhgvSSSiU2NJDSy1onjSXA==
 =J8jd
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20191014' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20191014
-------------------

Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628

	- logicpd pinmux
	- i.MX7ULP: imx_ddr_size
	- fixes Toradex i.MX6/i.MX7
	- pico-imx7d
	- tpc70 converted to DM
	- New Board: meerkat96
	- add HAB version command
	- i.MX8 :
      		imx8: Jump from alias to OCRAM address at SPL init
      		imx8qm/qxp: Set SPL TEXT base to OCRAM base
2019-10-14 13:00:51 -04:00
Yannick Fertré
d68ed0fad6 stm32mp1: configs: add display devices
Add support of panels otm8009A, RM68200 & DSI controller.
Limit resolution to 1280x800.

Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
2019-10-13 23:40:15 +02:00
Yannick Fertré
0e73892184 board: Add STM32F769 SoC, discovery board support
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
2019-10-13 23:38:47 +02:00
Yannick Fertré
23f965a4c6 dm: Add a dsi host uclass
Display Serial Interface (DSI) host can usefully be modelled
as their own uclass.
DSI defines a serial bus and a communication protocol
between the host and the device (panel, bridge).

Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
2019-10-13 23:34:43 +02:00
Shyam Saini
4e1c879f71 configs: icorem6: Enable nandbcb command
This also enables mtd configs which are required by nandbcb command.

This command would be used to configure boot control block(BCB) while
writing spl image on nand device.

Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
2019-10-13 22:49:12 +02:00
Ye Li
f9f42b07ff imx8qm/qxp: Set SPL TEXT base to OCRAM base
Modify the SPL TEXT base from OCRAM alias to OCRAM base 0x100000, so
we can use full OCRAM not limit to 96KB

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-10-13 22:49:12 +02:00
Lukasz Majewski
0bcb11fa1f imx: tpc70: Convert TPC70 (imx6q) board to use DM/DTS in SPL and u-boot
This patch converts the TPC70 to use driver model and device tree
description in both SPL and u-boot proper.

Notable changes (DM/DTS conversion):

- PINCTRL{_IMX6}
- DM_I2C
- enable 'regulator' and 'pmic' commands
- DM_MMC and BLK (USDHC)
- DM_ETH
- DM WDT (including SYSRESET)

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13 22:49:12 +02:00
Jun Nie
b86745efea pico-imx7d: add config to enable CAAM
Add config to enable CAAM so that hardware random number generator
works.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
2019-10-13 22:49:11 +02:00
Adam Ford
2881ec544d ARM: imx6q_logic: Enable Pin muxing in SPL
With the 256KB of OCRAM available to SPL now, there should be
enough room to enable the pinmuxing in SPL from the device tree.

This patch enables SPL_PINCTRL et al and adds the serial and
usdhc pin mux references to the -u-boot.dtsi file so the pins can be
configured from the device tree.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-13 22:49:11 +02:00
Adam Ford
f9faa1616b ARM: imx6q_logic: Enable 256KB OCRAM
Since this board config only supports, the i.MX6D/i.MX6Q configurations,
256K of on-chip RAM is available which increases the space available
to SPL to help further reduce board code and further enable device tree
functions.

This patch enables 256K of RAM.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-13 22:49:11 +02:00
Soeren Moch
954252aa35 board: tbs2910: Convert eth to driver model
So we can remove lots of legacy config code.

Signed-off-by: Soeren Moch <smoch@web.de>
2019-10-13 22:49:11 +02:00
Soeren Moch
2fabe35187 board: tbs2910: Convert pci to driver model
So we can get rid of legacy pci config code.

PCI_PNP is not required for this board, remove it to reduce the size of the
u-boot binary.

DM_PCI does not start the host controller automatically anymore. Do so
in preboot instead.

Signed-off-by: Soeren Moch <smoch@web.de>
2019-10-13 22:49:11 +02:00
Shawn Guo
6802d7951c Add i.MX7D based Meerkat96 board support
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of
96Boards community and complies with all Consumer Edition board
specifications.

https://www.novtech.com/products/meerkat96.html
https://www.96boards.org/product/imx7-96/

The initial supported/tested devices include:
 - Debug serial
 - SD
 - USB Host (with Ethernet)

With these support, it's good enough for loading Linux Kernel from SD or
Ethernet over USB.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-10-13 22:49:11 +02:00
Tom Rini
0c9cc5155c Merge branch '2019-10-11-master-imports'
- Assorted cleanups
- FAT bugfixes
- mediatek platform updates
2019-10-12 10:10:59 -04:00
Tom Rini
ee8da596eb sandbox: Remove sandbox_noblk build
At this point, all drivers that do not use CONFIG_BLK are past their
migration deadlines, so remove this config as it's no longer helpful and
hinders enhancing block drivers.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-11 19:05:14 -04:00
Lokesh Vutla
6685d2e26e configs: am43xx_evm: Enable USB support
spl_dm_init is failing as usb to be probed with the following error:
"omap_dwc3@483c0000: ret=-2"
Enable usb to make spl boot on am43xx devices

Reported-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:32:39 -04:00
Tero Kristo
752a45a153 board: ti: am335x-ice: Configure the CDCE913 clock synthesizer
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-10-11 13:32:39 -04:00
Tero Kristo
9850d4e52f board: ti: am43xx-idk: Configure the CDCE913 clock synthesizer
AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-10-11 13:32:39 -04:00
Tero Kristo
e8e683d33b board: ti: am57xx-idk: Configure the CDCE913 clock synthesizer
AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-10-11 13:32:39 -04:00
Lokesh Vutla
ac22511818 configs: am65x_evm_a53: Enable DISPLAY_CPUINFO
Enable CONFIG_DISPLAY_CPUINFO so that cpuinfo is printed during boot.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:32:20 -04:00
Lokesh Vutla
4fce88611d configs: j721e_evm_a72: Enable DISPLAY_CPUINFO
Enable CONFIG_DISPLAY_CPUINFO so that cpuinfo is printed during boot.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:31:50 -04:00
Lokesh Vutla
d53a177271 configs: j721e_evm_a72: Disable PSCI_RESET
J721E uses TISCI protocol to reset the device and does not
support PSCI reset. So disable PSCI reset.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:31:18 -04:00
Lokesh Vutla
523555fc17 configs: am65x_evm_a53: Disable PSCI_RESET
AM65x uses TISCI protocol to reset the device and does not
support PSCI reset. So disable PSCI reset.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:31:18 -04:00
Moses Christopher
51d4e47afa am335x, guardian: adapt guardian board to DM
- update partition table - remove env partitions
  - dts: add new interfaces (uart2, extra gpio-key)
         remove unneeded entries
         update nand timings for performance improvement
  - defconfig: adapt configurations to suit DM
               remove unneeded configs
  - am335x_guardian.h: remove mmc boot

Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-10-11 13:31:18 -04:00
Philippe Reynes
84a527bd09 bcm968580xref: enable spi-nor support
This commit enable the support of the spi-nor for the
broadcom reference board bcm968580xref.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Kursad Oney <kursad.oney@broadcom.com>
2019-10-11 10:09:17 -04:00
Kursad Oney
2a6abc6197 configs: Add hsspi/spi support to bcm963158.
This commit enable the support of the spi-nor for the
broadcom reference board bcm963158.

Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-10-11 10:09:16 -04:00
Suman Anna
65b91b2f8c configs: am65x_evm_a53: Enhance bootcmd to start remoteprocs
The A53 U-boot can support early booting of the MCU R5F remote processor(s)
from U-boot prompt to achieve various system usecases before booting the
Linux kernel. Update the default BOOTCOMMAND to provide an automatic and
easier way to start the MCU R5F cores through added environment variables.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 10:07:59 -04:00
Suman Anna
9af139c17b configs: am65x_evm_a53: Enable R5F remoteproc driver
Enable the R5F remoteproc driver for the AM65x GP EVM so that the
MCU domain R5F cores can be booted from A53 U-boot.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 10:07:50 -04:00
Suman Anna
750dc1ed51 configs: j721e_evm_a72: Enhance bootcmd to start remoteprocs
The A72 U-boot can support early booting of any of the R5F or C66x
or C71x remote processors from U-boot prompt to achieve various system
usecases before booting the Linux kernel. Update the default BOOTCOMMAND
to provide an automatic and easier way to start various remote processors
through added environment variables.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
2019-10-11 10:07:50 -04:00
Lokesh Vutla
5b1185c15b configs: j721e_evm_a72: Enable R5F and DSP remoteproc driver
Enable R5F and DSP remoteproc drivers for j721e running on a72.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 10:07:35 -04:00
Andreas Dannenberg
b8cc99a48f configs: am65x_evm_r5: Activate early console functionality
Activate early console functionality on AM654x devices to allow for an
alternate serial port to be used to support UART-based boot. This is so
that System Firmware (SYSFW) can get loaded over the serial port prior
to the main console being brought up and made available.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
2019-10-11 10:07:33 -04:00
Marek Vasut
110861992f ARM: socfpga: vining_fpga: Update environment
Update board environment to match the one used in deployment.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-09 22:57:40 +02:00
Marek Vasut
94a16b8e70 ARM: socfpga: vining_fpga: Rename VINING|FPGA
The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-09 22:54:17 +02:00
Tom Rini
44fb0d6c9f Xilinx/FPGA changes for v2020.01
FPGA:
 - Enable fpga loading on Versal
 - Minor fix
 
 Microblaze:
 - Fix LMB configurations to support initrds
 - Some other cleanups
 
 Zynq:
 - Minor config/dt changes
 - Add distro boot support for usb1 and mmc1
 - Remove Xilinx private boot commands and use only distro boot
 
 ZynqMP:
 - Kconfig cleanups, defconfig updates
 - Update some dt files
 - Add firmware driver for talking to PMUFW
 - Extend distro boot support for jtag
 - Add new IDs
 - Add system controller configurations
 - Convert code to talk firmware via mailbox or SMCs
 
 Versal:
 - Add board_late_init()
 - Add run time DT memory setup
 - Add DFU support
 - Extend distro boot support for jtag and dfu
 - Add clock driver
 - Tune mini configurations
 
 Xilinx:
 - Improve documentation (boot scripts, dt binding)
 - Enable run time initrd_high calculation
 - Define default SYS_PROMPT
 - Add zynq/zynqmp virtual defconfig
 
 Drivers:
 - Add Xilinx mailbox driver for talking to firmware
 - Clean zynq_gem for Versal
 - Move ZYNQ_HISPD_BROKEN to Kconfig
 - Wire genphy_init() in phy.c
 - Add Xilinx gii2rgmii bridge
 - Cleanup zynq_sdhci
 - dwc3 fix
 - zynq_gpio fix
 - axi_emac fix
 
 Others:
 - apalis-tk1 - clean config file
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXZ2mcwAKCRDKSWXLKUoM
 IT/KAJ4tL49YwINqCVGd7gafWvdfC4htygCcCgr9gLnJ+LjDQkxWT/r6faIcL00=
 =OnMk
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2020.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx/FPGA changes for v2020.01

FPGA:
- Enable fpga loading on Versal
- Minor fix

Microblaze:
- Fix LMB configurations to support initrds
- Some other cleanups

Zynq:
- Minor config/dt changes
- Add distro boot support for usb1 and mmc1
- Remove Xilinx private boot commands and use only distro boot

ZynqMP:
- Kconfig cleanups, defconfig updates
- Update some dt files
- Add firmware driver for talking to PMUFW
- Extend distro boot support for jtag
- Add new IDs
- Add system controller configurations
- Convert code to talk firmware via mailbox or SMCs

Versal:
- Add board_late_init()
- Add run time DT memory setup
- Add DFU support
- Extend distro boot support for jtag and dfu
- Add clock driver
- Tune mini configurations

Xilinx:
- Improve documentation (boot scripts, dt binding)
- Enable run time initrd_high calculation
- Define default SYS_PROMPT
- Add zynq/zynqmp virtual defconfig

Drivers:
- Add Xilinx mailbox driver for talking to firmware
- Clean zynq_gem for Versal
- Move ZYNQ_HISPD_BROKEN to Kconfig
- Wire genphy_init() in phy.c
- Add Xilinx gii2rgmii bridge
- Cleanup zynq_sdhci
- dwc3 fix
- zynq_gpio fix
- axi_emac fix

Others:
- apalis-tk1 - clean config file
2019-10-09 16:22:03 -04:00
Tom Rini
eaa0bde051 u-boot-imx-20191009
-------------------
 
 Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532
 
 - MX6UL / ULZ
 - Toradex board
 - Allow to set OCRAM for MX6Q/D
 - MX7ULP
 - MX8: (container image, imx8mq_mek), SCU API
 - fix several board booting from SD/EMMC (cubox-i for example)
 - pico boards
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAl2dlTAPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3yfgL/1b4pKCwxswK42XkPpdHN1u/v2W/PVDanl/H
 EYxlluHVFH23bLTjLvrrgQjAnZD1VQhxWq3bwCMoJ8vb9tYQ3d9vq7XADQ0WVQV+
 EfhE33fVRPRT3rEdhDKWm+y1mL8YPvYEBnr9li7qU9n1VxiwONPXxMXMqoo9/lbM
 b6lJaG5KkuK8Ofx3cYFVQeAEdsFYIJ2aXtTqsqrV9o2sjruOuG3Ux+6Ov+9O0crY
 q8MXvW6kwWkVVNriVV7Yal0pomPZfMTqft007En9Mv2FtXqMeCWZ4Xh2LtRylR7n
 ruIbo94jkPuwuZ0p/6SeiyopoG/hU/skrkJv1s8W70DOsyaunP2BsveYXEjMV2Rb
 DomotcJit9Ws6P7rOP1oI8OvxSxVN8n6mo23UviZd8MjNAmOm49BtSxVGGB+pwmr
 ufGFG4MGQ5VpCxmzh6KrJCLXpI/mhKrkBkZy58cUbus7aPv3es/jBmmtGlU3m6ka
 NlEzHOX1hpJV/lhLvxjqRhVxuXvXOA==
 =+e3p
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20191009' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20191009
-------------------

Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532

- MX6UL / ULZ
- Toradex board
- Allow to set OCRAM for MX6Q/D
- MX7ULP
- MX8: (container image, imx8mq_mek), SCU API
- fix several board booting from SD/EMMC (cubox-i for example)
- pico boards

[trini: display5 merged manually]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-09 11:44:45 -04:00
Tom Rini
8c05abad13 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
- Move WATCHDOG_TIMEOUT_MSECS to Kconfig (Heiko)
2019-10-08 18:45:49 -04:00
Tom Rini
efea5a34bb Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86
- Rename existing FSP code to fsp1
- Add fsp2 directory in preparation to support FSP 2.0
- Various x86 platform codes update
- Various bug fixes and updates in dm core, sandbox and spl
2019-10-08 18:45:26 -04:00
Heinrich Schuchardt
86d2b28b28 configs: sheevaplug disable EFI_UNICODE_CAPITALIZATION
With upcoming patches u-boot.kwb gets too large.

Save 3740 bytes in u-boot.kwb by disabling Unicode support in the UEFI
sub-system.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-10-08 16:36:37 +02:00
Joris Offouga
f730fdf98b pico-imx7d: fix splash logo drawing
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08 16:36:37 +02:00
Stefano Babic
d714a75fd4 imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2019-10-08 16:36:37 +02:00
Parthiban Nallathambi
39fd054fee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
CONFIG_SPL_TEXT_BASE is moved to common/spl/Kconfig, update
pcl063_ull defconfig.

Signed-off-by: Parthiban Nallathambi <pn@denx.de>
2019-10-08 16:36:37 +02:00
Saravanan Sekar
a7031d9f54 imx: variscite: Fix regression of SPL and U-boot booting
1. Commit 3a7c45f6a7 ("simple-bus: add DM_FLAG_PRE_RELOC flag to
simple-bus driver") causes some i.MX boards that were converted
to DM, such as warp7, to fail to boot.

As explained by Lukas Auer:

"With the patch, U-Boot probes the drivers for devices under simple-bus
device tree nodes in the pre-relocation device model. The default value
of CONFIG_SYS_MALLOC_F_LEN (0x4000) leaves U-Boot with not enough memory to
do this, causing it to hang."

Fix this problem by providing a convenient default value for
CONFIG_SYS_MALLOC_F_LEN.

2. CONFIG_SPL_TEXT_BASE was moved to Kconfig, so added in defconfig
"configs: move CONFIG_SPL_TEXT_BASE to Kconfig"
(sha1: f89d6133ee)

Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:36:37 +02:00
Adam Ford
7cf388fa69 ARM: imx6q_logic: Enable DM_SERIAL
In order to call preloader_console_init from board_init_f when
DM_SERIAL is enabled, it neesd to call spl_early_init() to get early access
to DM and device tree.

This patch calls spl_early_init just before preloader_console_init()
and enables DM_SERIAL and SPL_DM_SERIAL.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08 16:36:37 +02:00
Parthiban Nallathambi
a919b6ba37 imx: pcl063: add nand boot support
Booting from NAND needs nandbcb and nand boot device selection

Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:36:37 +02:00
Peng Fan
9b15ce9193 imx: Add i.MX8MM EVK board support.
Add board and SoC dts
Add ddr training code
support SD/MMC/GPIO/PINCTRL/UART

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:36:36 +02:00