It is useful to be able to find hex values and strings in a memory range.
Add a command to support this.
cmd: Fix 'md' and add a memory-search command
At present 'md.q' is broken. This series provides a fix for this. It also
implements a new memory-search command called 'ms'. It allows searching
memory for hex and string data.
END
Signed-off-by: Simon Glass <sjg@chromium.org>
This code is never enabled, last board that used it was ELPPC which
was removed some 5 years ago, so just remove this code altogether.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This converts the following to Kconfig:
CONFIG_BZIP2
CONFIG_GZIP
CONFIG_LZO
CONFIG_ZLIB
CONFIG_LZMA
CONFIG_LZO
Signed-off-by: Tom Rini <trini@konsulko.com>
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
There is no real need to exactly define space for saving patterns for
alternate memory test. It is much easier to allocate space on the stack and
use it instead of trying to find out space where pattern should be saved.
For example if you want to test the whole DDR memory you can't save patter
to DDR and you need to find it out. On Xilinx devices DDR or OCM addresses
were chosen but that means that OCM needs to be mapped and U-Boot has
access permission there.
It is easier to remove this limitation and simply save it on stack because
it is very clear that memory test can't rewrite U-Boot and U-Boot has also
full access to memory where runs from.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
These macros are not used by any board, remove them to simplify
the driver. The EEPROM accessors are still retained however, as
those might still be useful.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Remove the references in README on CONFIG_SYS_RCAR_I2C_* not use
in U-Boot drivers/i2c/rcar_i2c.c, since commit a4d9aafadb ("i2c:
rcar_i2c: Remove the driver") and commit a06a0ac36d ("i2c: rcar_i2c:
Add DM and DT capable I2C driver")
Checked by the command: grep -r SYS_RCAR_I2C *
And these CONFIG are only defined in
arch/arm/mach-rmobile/include/mach/rcar-base.h
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
MinGW build for U-Boot tools has been broken for years. The official
support of Windows build is now MSYS2. Remove the MinGW support codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
boards.cfg is not delivered with the U-Boot source. So it is preferable to
look at configs/*_defconfig to identify available deconfigs.
Fix a typo.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update some reference in README file detected by
scripts/documentation-file-ref-check
*.README => README.*
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
As indicated elsewhere in the README, the standalone CHANGELOG file was
removed in 2010. Drop the instructions for creating patches on creating
a standalone CHANGELOG entry.
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Both CMD_MX_CYCLIC and MX_CYCLIC are in use and defined in Kconfig,
but only the non-CMD version currently does anything. This changes all
usages to prefer the CMD_MX_CYCLIC option (since it's only affecting
addition of the commands), and switches defconfigs using the non-CMD
version to use the CMD version.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is not really a CONFIG since it is not intended to be set by boards.
Move it into the compiler header with other similar defines, and rename
it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This seems pretty old now. It has not been converted to driver model and
is not used by any boards.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
These should be moved to driver model, but in the meantime, move them
out of the common header to help reduce its size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The earlier commit....
commit a5a5d997b4 ("spl: Allow performing BSS init early before board_init_f()")
...introduced the ability to use BSS from SPL's board_init_f() as it may
be required in certain exceptional use cases so go ahead and update the
README to reflect this change. Note that as highlighted with the changes
the use of the associated CONFIG option is generally not recommended.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
commit 49116e6d23 ("doc: arch: Convert README.sandbox to reST")
Moves README.sandbox to doc/arch.
Replace all the existing instances to point to the right documentation
file.
Signed-off-by: Keerthy <j-keerthy@ti.com>
The non-CONFIG_SPL_FRAMEWORK SPL used on some PowerPC platforms have a
choice between CONFIG_SPL_NAND_BOOT, CONFIG_SPL_MMC_BOOT and
CONFIG_SPL_SPI_BOOT. Migrate this to Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the main symbol for Freescale Fman Ethernet controller option to
Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and
rename the SPIFLASH one to follow the same format as all of the others.
To do this fully we need to migrate CONFIG_QC, do so.
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SYS_[DI]CACHE_OFF had been partially converted to Kconfig
parameters; only for the ARC architecture. This patch turns these two
parameters into Kconfig items everywhere else they are found.
All of the include/configs/* and defconfig changes in this patch are
for arm machines only. The Kconfig changes for arc, nds32, riscv,
and xtensa have been included since these symbols are found in code
under arch/{arc,nds32,riscv,xtensa}, however, no currently-defined
include/configs/* or defconfigs for these architectures exist which
include these symbols.
These results have been confirmed with tools/moveconfig.py.
Acked-by: Alexey Brodkin <abrodkin@snopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Re-migrate for a few more boards]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_BOOT
As requested by Michal Simek <michal.simek@xilinx.com>, these boards
have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:
xilinx_zynqmp_zc1275_revB
xilinx_zynqmp_zc1751_xm018_dc4
xilinx_zynqmp_zc1751_xm019_dc5
xilinx_zynqmp_zcu100_revC
xilinx_zynqmp_zcu102_rev1_0
xilinx_zynqmp_zcu102_revA
xilinx_zynqmp_zcu102_revB
xilinx_zynqmp_zcu104_revA
xilinx_zynqmp_zcu104_revC
xilinx_zynqmp_zcu106_revA
xilinx_zynqmp_zcu111_revA
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch removes the CONFIG_AT91_HW_WDT_TIMEOUT as its not needed any
more. The WD timeout value can be provided via the "timeout-sec" DT
property. If not provided this way, the default value of 2 seconds will
be used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED
I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This is the same migration path as commit b6251db8c3 ("Kconfig:
Introduce USE_BOOTCOMMAND and migrate BOOTCOMMAND").
I also moved the description in README to the Kconfig help.
I ripped off the sentence about 'LWMON' since it is gone already.
I only let my boards migrate, leaving the rest to platform maintainers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This driver is replaced by drivers/i2c/i2c-cdns.c DM based driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Heiko Schocher <hs@denx.de>
A few platforms recently added in CONFIG_DFU_MMC under include/configs
rather than via the defconfig, update them.
Signed-off-by: Tom Rini <trini@konsulko.com>
No mainline board enables CONFIG_MCAST_TFTP and there have been
compilation issues with the code for some time. Additionally, it has a
potential buffer underrun issue (reported as a side note in
CVE-2018-18439).
Remove the multicast TFTP code but keep the driver API for the future
addition of IPv6.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In legacy CONFIG_HARD_SPI initalizing spi_init code, which
was removed during dm conversion cleanup.
So remove the dead instances of CONFIG_HARD_SPI, and related
code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Caches should be configured to mode CONF_CM_CACHABLE_NONCOHERENT
(or CONF_CM_CACHABLE_COW when a CM is available). There is no
need to make this configurable.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Some MIPS systems store some board-specific boot configuration
in the U-Boot binary at offset 0x10. This is used by Malta boards
and by Lantiq/Intel SoC's when booting from parallel NOR flash.
Convert the hard-coded values to Kconfig options to remove such
board-specific stuff out of the generic start.S code. This also
deprecates the config option CONFIG_SYS_XWAY_EBU_BOOTCFG.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
You do not need to use the typedefs provided by compiler.
Our compilers are either IPL32 or LP64. Hence, U-Boot can/should
always use int-ll64.h typedefs like Linux kernel, whatever the
typedefs the compiler internally uses.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add the config option `CONFIG_SPL_NAND_IDENT` for using the NAND chip ID list
to identify the NAND flash in SPL.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
