Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
All of one PCNET users has this option set, make this default
and drop this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
These macros guard one switch-case statement, which grows mips malta
by some 20 bytes if debug is enabled, and even less if it is not. To
make the code simpler, just support all the NICs and be done with it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MISC_INIT_R
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that the fallback value of CONFIG_SYS_PBSIZE in
include/config_fallbacks.h has been adjusted, remove its definition
from a large number of board configuration files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all
configurations that were using the default value.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Drop <config.h> from stih410-b2260.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_PCI
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Move this in to Kconfig with a default of 115200.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce CONFIG_PCI_PNP in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Re-generate configs and include/configs/ changes]
Signed-off-by: Tom Rini <trini@konsulko.com>
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Both real Malta boards & emulators that mimic Malta (eg. QEMU) can
support MIPS64 CPUs. Allow MIPS64 builds of U-Boot for such boards,
which enables the user to make use of the whole 64 bit address space.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Move CONFIG_SYS_TEXT_BASE to Kconfig, and add default values in board
Kconfig files matching what was present in their config headers. This
will make it cleaner to conditionalise the value for Malta based on 32
vs 64 bit builds.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Make use of device model & device tree to probe the UART driver. This is
the initial step in bringing Malta up to date with driver model, and
allows for cleaner handling of the different I/O addresses for different
system controllers by specifying the ISA bus address instead of a
translated memory address.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The address of the UART differs based upon the system controller because
it's actually within the I/O port region, which is in a different
location for each system controller. Rather than handling this as 2
UARTs with the correct one selected at runtime, use I/O port accessors
for the UART such that access to it gets translated into the I/O port
region automatically.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.
Signed-off-by: Tom Rini <trini@konsulko.com>
config.h is used in target and host code and therefore should not
pull in target header files to avoid compile errors. This change
is also required for the MIPS header file sync done in follow-up
patches.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add option to set shell prompt string from menuconfig and migrate
boards globally.
The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
files. This results in a streamlined default value across platforms, and
includes the following files: spear-common, sunxi-common, mv-common,
ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
not updated in their respective defconfig files under the assumption that
since they did not explicitly define a value, they're fine with whatever
the default is.
- On the other hand, boards that relied on a value defined in some
<boards>_common.h file such as woodburn_common, rpi-common,
bur_am335x_common, ls2085a_common, siemens_am33x_common, and
omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
assigning a value for CONFIG_SYS_PROMPT.
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
We have done with the generic board conversion for all the boards
of ARC, Blackfin, M68000, MicroBlaze, MIPS, NIOS2, Sandbox, X86.
Let's select SYS_GENERIC_BOARD for those architectures, so we can
tell which architecture has finished the conversion at a glance.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
The ability to load ELF files is sometimes useful on Malta boards,
particularly for use with small embedded applications. Enable the
loadelf command in the malta config.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The malta board is used for development and thus the shell is interacted
with often. Enable HUSH to make the experience a little more pleasant.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds IDE support to the MIPS Malta board. The IDE controller
is enabled after probing the PCI bus and otherwise just makes use of
U-boot generic IDE support.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch converts the MIPS Malta development board to make use of the
generic board code now that it is supported on MIPS.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
CONFIG_SYS_NS16550_CLK specifies the rate of the clock 16x the baud
rate. The SMSC FDC37M81x datasheet states that a divider of 1 results in
a UART at 115200 baud, thus the x16 clock rate is 115200 * 16.
Previously the divider was left at 0 which led to a rate of 38400 baud
regardless of CONFIG_BAUDRATE or the baudrate environment variable.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The physical base address of the NOR flash is 0x1e000000
on the Malta boards. The hardware also maps the first 4MiB
of the flash into the 0x1fc00000-0x1fffffff range.
Currently, U-Boot uses the mapped address to access the
flash, which does not work in recent qemu versions.
Since commit a427338b222b43197c2776cbc996936df0302f51
(mips_malta: correct reading MIPS revision at 0x1fc00010)
writing to the mapped address space causes a CPU exception.
Due to the exception, U-Boot hangs during boot when it tries
to detect the CFI flash chip.
Use the correct physical address for the MALTA_FLASH_BASE
constant to fix the problem. In order to avoid relocation
problems, also update the CONFIG_SYS_{TEXT,MONITOR}_BASE
constants.
The change makes it possible to start U-Boot on a Malta
board emulated with Qemu 1.6.1 and 1.7.0-rc0. It also
works on older versions (tested with 1.1.1, 1.2.2, 1.4.2,
1.5.3).
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
The memsize environment variable must contain the
memory size in bytes on the Malta board. Otherwise
Linux will use wrong memory size which causes a kernel
panic.
Define CONFIG_MEMSIZE_IN_BYTES in malta.h to avoid
that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Allow the environment to be stored in the monitor flash of a Malta
board. The environment is stored in the final 128KB of the flash, which
both leaves the majority of the flash available for U-boot code and also
matches the location which YAMON uses.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This is actually required in order for a Linux kernel to boot
successfully on a physical Malta board. Without enabling the RTC, a
Malta Linux kernel will get stuck in its estimate_frequencies function
on boot.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
These will now be detected at runtime, allowing a single U-boot
configuration to function correctly with different bitstreams. Without
this you may need to re-configure, re-build and re-flash U-boot to your
Malta if you flash a new bitstream with a different cache configuration
to your old bitstream.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This model of the pcnet is used in current Malta boards, at least in the
Malta-R rev 3. Enable support for it.
The Malta also has the ethernet controller PROM containing its MAC
address, so enable support for that in order to read that MAC address.
DHCP is a very useful feature to have available for many networks,
enable support for it also.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch adds support for running on Malta boards using coreFPGA6
core cards, including support for the msc01 system controller used
with them. The system controller is detected at runtime allowing one
U-boot binary to run on a Malta with either.
Due to the PCI I/O base differing between Maltas using gt64120 & msc01
system controllers, the UART setup is modified slightly. A second UART
is added so that there is one pointing at the correct address for each
system controller. The Malta board then defines its own
default_serial_console function to select the correct one at runtime.
The incorrect UART will simply not function.
Tested on:
- A coreFPGA6 Malta running interAptiv and proAptiv bitstreams, both
with and without an L2 cache.
- QEMU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This is in preparation for adapting this board to function correctly on
a physical MIPS Malta board. The board is moved into an "imgtec" vendor
directory at the same time in order to ready us for any other boards
supported by Imagination in the future.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
