The driver was using milliseconds and programming it into a register
which takes ticks of the watchdog clock, which runs at 1MHz. This meant
we were off by 1000 with the desired value.
When 06985289d4 ("watchdog: Implement generic watchdog_reset()
version") was added the aspeed board would leave the watchdog running,
causing it to bite before u-boot was done.
Discovered by booting in qemu:
$ qemu-system-arm -M ast2500-evb -drive file=test.img,format=raw,if=mtd -nographic -no-reboot -d cpu_reset
U-Boot 2019.07-rc3-00091-g2253e40caef5 (Jun 06 2019 - 16:53:23 +0930)
Model: Aspeed BMC
DRAM: 496 MiB
WDT: Started with servicing (60s timeout)
MMC:
In: serial@1e784000
Out: serial@1e784000
Err: serial@1e784000
Watchdog timer expired.
Fixes: 06985289d4 ("watchdog: Implement generic watchdog_reset() version")
Signed-off-by: Joel Stanley <joel@jms.id.au>
- LS1046AFRWY support
- USB errata fix and secure boot defconfig support for LS1028A
- Enabled SDHC and SATA for LX2160
- LS1046A serdes fixes
- other minor fixes
Allow device mode in DWC2 driver when device tree select the dr_mode
"peripheral" or "otg".
The device mode is not allowed when dr_mode = "host" in device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Manage g-tx-fifo-size as a array as specify in the binding.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
u-boot is trying to make CONFIG_BLK as a hard requirement
for DM_MMC. But now it's still not.
config BLK
bool "Support block devices"
depends on DM
default y if DM_MMC
When fsl_esdhc driver was reworked for DM_MMC support, DM_MMC
without CONFIG_BLK enabled wasn't considered. This patch is to
fix probe issue without CONFIG_BLK enabled.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
U-Boot code currently only applies this restriction to HS200 mode,
extend this to HS400 mode as well.
Currently U-Boot code not support accessing boot partition in HS200/400
mode. This needs more check.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently getvar_has_slot() invocation for "boot" and "system"
partitions always returns affirmative response regardless the fact of
existence of these partitions, which leads to impossibility to flash them
on old non-A/B AOSP setups, where _a/_b suffixes aren't used:
$ fastboot flash boot boot.img
Sending 'boot__a' (11301 KB) OKAY [ 0.451s]
Writing 'boot__a' FAILED (remote: 'cannot find partition')
fastboot: error: Command failed
Although partition layout is:
-> part list mmc 0
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000800 0x000107ff "boot"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: ea2e2470-db4a-d646-b828-10167f736d63
2 0x00010800 0x000127ff "environment"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: 10a819d2-6004-3d48-bd87-114e2a796db9
3 0x00012800 0x0001a7ff "recovery"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: 9ea116e4-8a34-0c48-8cf5-2fe9480f56cd
4 0x0001a800 0x0031a7ff "system"
attrs: 0x0000000000000000
......
This patch adds checks of existence for requested partitions
on eMMC/NAND.
Fixes: f73a7df984 ("net: fastboot: Merge AOSP UDP fastboot")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Extract fastboot_*_get_part_info() usage for MMC and NAND into
getvar_get_part_info() function, as it will be needed further in other
functions. This way we can avoid code duplication and mess with
preprocessor directives across all points of usage.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
In fastboot_*_get_part_info() functions we can use stronger typing by
expecting const strings.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
In commit [1] fastboot tool was changed w.r.t. new A/B specification [2],
and now we should report slot names in "a" format instead of "_a".
Latter is now considered legacy and we shouldn't rely on that anymore.
Due to this one can observe next error with recent fastboot tool:
$ fastboot flash boot boot.img
Sending 'boot__a' (11301 KB)
OKAY [ 0.451s]
Writing 'boot__a'
FAILED (remote: 'cannot find partition')
fastboot: error: Command failed
Let's use new slot format in order to fix double underscores "__" and to
be in sync with AOSP master.
[1] 8091947847
[2] https://source.android.com/devices/tech/ota/ab/ab_implement#partitions
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Mark LPC32XX_SSP as DEPRECATED, this so the resulting build shows
warning for deprecated configuration enabled and associated code
will remove in v2019.07 release.
Cc: Albert ARIBAUD <albert.aribaud@3adev.fr>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Sylvain Lemieux <slemieux@tycoint.com>
[trini: Switch to DEPRECATED]
Signed-off-by: Tom Rini <trini@konsulko.com>
Mark SOFT_SPI as DEPRECATED, this so the resulting build shows
warning for deprecated configuration enabled and associated code
will remove in v2019.07 release.
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[trini: Switch to DEPRECATED]
Signed-off-by: Tom Rini <trini@konsulko.com>
Mark SH_SPI as DEPRECATED, this so the resulting build shows
warning for a deprecated configuration enabled and associated code
will remove in v2019.07 release.
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[trini: Switch to DEPRECATED]
Signed-off-by: Tom Rini <trini@konsulko.com>
Mark MXS_SPI as DEPRECATED, this so the resulting build shows
warning for broken configuration enabled and associated code
will remove in v2019.07 release.
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[trini: Switch to DEPRECATED]
Signed-off-by: Tom Rini <trini@konsulko.com>
- pinctrl: meson-gxbb: add hdmi related pins to fix HDMI on GXBB
- pinctrl: meson: add support for getting pinmux status
- pinctrl: meson-g12a: add support for drive-strength-microamp property
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QA+5
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190612' of git://git.denx.de/u-boot-amlogic
- pinctrl: meson-gx: fix GPIO_TEST_N and GPIOCLK_ groups
- pinctrl: meson-gxbb: add hdmi related pins to fix HDMI on GXBB
- pinctrl: meson: add support for getting pinmux status
- pinctrl: meson-g12a: add support for drive-strength-microamp property
The GXBB pinctrl is missing pins related to HDMI, namely hot plug
detection (hpd) and I2C (sda + scl).
This fixes HDMI support for GXBB in u-boot.
Reported-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
add drive-strength bank regiter and bit value for G12A SoC
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
drive-strength-microamp is a new feature needed for G12A SoC.
the default DS setting after boot is usually 500uA and it is not enough for
many functions. We need to be able to set the drive strength to reliably
enable things like MMC, I2C, etc ...
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In order to support the "pinmux status" command, use the common functions
to get the pins count and names, and add the AXG specific function to get
the current function from registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In order to support the "pinmux status" command, use the common functions
to get the pins count and names, and add the GX specific function to get
the current function from registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Maxime Jourdan <mjourdan@baylibre.com>
In order to support the "pinmux status" command, add common function
to get pins count and pin name.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The GPIO_TEST_N was in the wrong pmx group table, move it back with the AO
groups, GPIODV_18 was missing, add it back, and finally the GPIOCLK_*
group names were missing.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2C9f
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20190606' of https://github.com/pchotard/u-boot
- Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
This commit is necessary to be able to re-use the pinctrl code in early
SPL to properly configure pins.
The problem is that those "static" structures (without explicit
initialization) are placed in the SDRAM area, which corresponds to
u-boot proper (not even SPL).
Hence, when one wants to configure pins before relocation via DTS/DM,
the board hangs (imx6q SoC powered one) as only OCRAM area is available
(0x009xxxxx).
This commit prevents from this issue by moving the imx6_pinctrl_soc_info
structure to data section (from BSS).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
We should not access reserved register on i.MX8, otherwise met SERROR
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add DM support and support for probing the iMX PCI driver from DT.
The legacy non-DM support is retained, however shall be removed once
DM PCI is the only option remaining.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Pass the driver private data around the driver as much as possible, instead
of having it as a static global variable. This is done in preparation for
the DM conversion, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The driver limits the config space base to 32bit, however it can be
64bit on 64bit iMX hardware too. Remove that limitation. This patch
has no impact on the iMX6, which is the only SoC currently supported
by this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Pull out hard-coded register base addresses into driver private
structure in preparation for DM conversion. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This fixes the i.MX 8 fuse driver to actually build for i.MX 8QM as
well.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Trying to bring up uSDHC2 the following error message was observed:
MMC: imx8_clk_set_rate(Invalid clk ID #60)
imx8_clk_set_rate(Invalid clk ID #60)
usdhc@5b030000 - probe failed: -22
This commit fixes this by properly setting resp. clocks.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
in mxc_spi_probe() plat and mxcs pointer are created:
struct mxc_spi_slave *plat = bus->platdata;
struct mxc_spi_slave *mxcs = dev_get_platdata(bus);
which have the same value. Remove plat pointer.
Signed-off-by: Heiko Schocher <hs@denx.de>
Commit 22191ac353 ("drivers/crypto/fsl: assign job-rings to
non-TrustZone") breaks HABv4 encrypted boot support in the
following i.MX devices:
- i.MX6UL
- i.MX7S
- i.MX7D
- i.MX7ULP
For preparing a HABv4 encrypted boot image it's necessary to
encapsulate the generated DEK in a blob. In devices listed
above the blob generation function takes into consideration
the Job Ring TrustZone ownership configuration (JROWN_NS)
and can be only decapsulated by the same configuration.
The ROM code expects DEK blobs encapsulated by the Secure World
environments which commonly have JROWN_NS = 0.
As U-Boot is running in Secure World we must have JROWN_NS = 0
so the blobs generated by dek_blob tool can be decapsulated
by the ROM code.
Job-rings assignment is now handled in OP-TEE OS, this commit can
be safely reverted.
https://github.com/OP-TEE/optee_os/pull/2986
This reverts commit 22191ac353.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
https://source.codeaurora.org/external/imx/uboot-imx
cherry picked, styled and merged commits:
- MLK-18387 pmic: Add pmic driver for BD71837: e9a3bec2e95a
- MLK-18590 pmic: bd71837: Change to use new fdt API: acdc5c297a96
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The code that sets a regulator by looking up the voltage in a table had
an off by one error. vsel_mask is a bitmask, not the number of table
entries, so a vsel_mask value of 0x7 indicates there are 8, not 7,
entries in the table.
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Support DM in the MPC8xxx SPI driver, and remove the legacy SPI
interface.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The comment before the transmission loop in conjunction with the
definition of SPI_TIMEOUT as 1000 implies that the loop is supposed to
have a timeout value of 1000 ms. But since there is no mdelay(1) or
similar in the loop body, the loop just runs 1000 times, without regard
for the time elapsed.
To correct this, use the standard get_timer functionality to properly
time out the loop after 1000 ms.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Decreasing the bit length and increasing the write data pointer should
be done when there are more than 32 bit of data, not 16 bit.
This did not produce incorrect behavior, because the only time where the
two checks produce different outcomes is the case of 16 < bitlen < 32,
and in this case the subsequent transmission is the last one regardless,
hence the additional bit length decrease and write data pointer increase
has no effect anyway.
Still, the correct check is the check for "bitlen > 32", so correct this
behavior.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Minize the time the adapter is disabled (via SPI_MODE_EN
clearing/setting) to just the character length setting, and only set up
the temporary data writing variable right before we need it, so there is
a more clear distinction between setting up the SPI adapter, and setting
up the data to be written.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
