The current code checks that no partitions overlap with the GPT partition
table using the offset of the first LBA usable for that partition.
This works fine, unless you have a partition entry that is further away
than it usually is and you want to create partitions in the gap between the
GPT header and the GPT partition entries, for example to reflash a
bootloader that needs to be set there.
Rework the test to something a bit smarter that checks whether a partition
would overlap with either the GPT header or the partition entries, no
matter where it is on the disk.
Partitions that do not have a start LBA specified will still start at the
first LBA usable set in the GPT header, to avoid weird behaviours.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The gpt_fill_pte will need to access the device block size. Let's pass the
device descriptor as an argument.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The start variable is only used inside a loop, and is never affected inside
it, so it's a purely local variable.
In the same way the partition size is accessed several times, so we can
store it in a variable.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Both the config option and the DT options specify the offset to set the GPT
at in bytes, yet the code treats those values as block numbers.
Fix that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add the following options to drivers/misc/Kconfig:
SYS_I2C_EEPROM_ADDR
SYS_I2C_EEPROM_BUS
SYS_EEPROM_SIZE
SYS_EEPROM_PAGE_WRITE_BITS
SYS_EEPROM_PAGE_WRITE_DELAY_MS
SYS_I2C_EEPROM_ADDR_LEN
SYS_I2C_EEPROM_ADDR_OVERFLOW
This does not migrate any boards, but provides a foundations for
those who want/need these options
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate uniphier]
Signed-off-by: Tom Rini <trini@konsulko.com>
Without ethernet cable plugged, "ip=dhcp" leads to a complete hangup in
Linux booting and the system does not boot into userland at all. Since
its not required to have an active network connection on these board,
lets remove this statement from the default environment.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It was noticed a few times, that the reboot from Linux (reboot command)
is different from the reboot (reset command) under U-Boot. The U-Boot
version does seem to reset the board more deeply (PCI cards etc) than
the Linux reboot.
This is actually caused by missing full reset bit in the reset register
value in the ACPI FADT table.
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
The atomic preop register can only be written when SPI settings are
not locked, otherwise it's read-only.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
In ich_spi_xfer() when the driver presets control fields, control
variable gets assigned twice. Apparently only the last assignment
takes effect. Remove the other one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Manually enable SYS_NAND_U_BOOT_LOCATIONS.
Set CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000 and remove it from header
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_SPL_OMAP3_ID_NAND
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_I2C_BUS_MAX
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Fix AM43XX drop AM44XX]
Signed-off-by: Tom Rini <trini@konsulko.com>
For consistency with other platforms and in preparation of Kconfig
migration, let's change Several TI platforms that use I2C_BUS_MAX
to CONFIG_SYS_I2C_BUS_MAX
Signed-off-by: Adam Ford <aford173@gmail.com>
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's
not strictly part of fastboot.
- Add some defaults for the fastboot buffer location and size
- Migrate all options listed in cmd/fastboot/Kconfig
- Cleanup the README
Signed-off-by: Tom Rini <trini@konsulko.com>
This syncs all of the currently Kconfig'd symbols out of the headers and
into the defconfig files. This has two exceptions, first am335x_evm
needs to be converted to DM in SPL and then it can stop undef'ing
CONFIG_DM_USB. Leaving this as-is results in a build failure, and
without work, run time failure. The other case is am43xx_evm.h and in
turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB
host mode in SPL, but still desire to have gadget mode in U-Boot proper.
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit 1d20170467, reversing
changes made to 6aee2ab68c.
The mxc_ipuv3_fb.c changes introduce build failures on some targets.
Signed-off-by: Tom Rini <trini@konsulko.com>
SUNXI_GMAC was still used to configure the code where as the
same has been renamed and moved to Kconfig in below commit
"sunxi: Move SUNXI_GMAC to Kconfig"
(sha1: 4d43d065db)
Signed-off-by: Dave Prue <dave@prue.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
[Tweek commit message, config_whitelist.txt, build-whitelist.sh]
Signed-off-by: Jagan Teki <jagan@openedev.com>
When enabling the new mmc timing mode, we inadvertently clear all the
remaining bits in the new timing mode register. The bits cleared
include a default phase delay on the output clock. The BSP kernel
states that the default values are supposed to be used. Clearing them
results in decreased performance or transfer errors on some boards.
Fixes: de9b1771c3 ("mmc: sunxi: Support new mode")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Memory dt node update introduced by spl_fixup_fdt() in below
commit was making DDR configuration in-appropriate
to boot falcon mode. Hence added dram_init_banksize for
explicit assignment of proper base and size of DDR.
"boot: fdt: Perform arch_fixup_fdt() on the given device tree for falcon boot"
(sha1: 6e7585bb64)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The NXP i.MX 6UL and 6ULL do not support SATA and have no SATA
boot mode, hence remove it from the boot device detecion. This
fixes a build error introduced with 3bd1642d4d ("imx: fix USB
boot mode detection for i.MX 6UL and 6ULL")
Fixes: 3bd1642d4d ("imx: fix USB boot mode detection for i.MX 6UL and 6ULL")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
U-boots spi-nor support is currently considered a work in progress. For
now to avoid issues it is necessary to add a "spi-flash" compatible
string. Eventually the "jedec,spi-nor" will be sufficient when the core
U-boot code is updated to support it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Now the entry to the NAND driver init can be is controlled by DT;
it should not hurt to compile the driver all the time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This imply was added when the option was moved by the moveconfig tool,
but the intention is not clear. Move it to defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is now set up by the pinctrl driver when the NAND driver is
probed. Remove the legacy code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
CONFIG_NAND_DENALI select's CONFIG_SYS_NAND_SELF_INIT, so the
NAND initialization process is driven by the driver itself.
CONFIG_SYS_NAND_MAX_CHIPS and CONFIG_SYS_NAND_BASE are unused.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The new SoC PXs3 changed the address of PLL, but still uses the
same PLL name. We can not define SC_*PLLCTRL in the common header.
Move them to per-SoC .c file. Also, fix some PLL comments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The #include <common.h> was added for mdelay(). Later, the declaration
of mdelay was moved to <linux/delay.h> by commit 5bc516ed66 ("delay:
collect {m, n, u}delay declarations to include/linux/delay.h").
There is no need to include <common.h> now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
A patch for NAND uclass support was proposed about half a year ago:
https://patchwork.ozlabs.org/patch/722282/
It was not merged and I do not see on-going work for this.
Without DM-based probing, we need to set up pinctrl etc. in an ad-hoc
way and give lots of crappy CONFIG options for base addresses and
properties, which are supposed to be specified by DT. This is painful.
This commit just provides a probe hook to retrieve "reg" from DT and
allocate private data in a DM manner. This DT driver is not essentially
a NAND driver, in fact it is (ab)using UCLASS_MISC. Once UCLASS_NAND is
supported, it would be possible to migrate to it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Linux supports platform_get_resource_byname() to look up a resource
by name.
We want a similar helper. It is useful when a device node has named
register regions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Boards can skip display interface init using board_video_skip().
If display interface was not initialized (e.g. no ipuv3 framebuffer
registered or IPU clock disabled), booting Linux stops due to the
crash in IPU shutdown function, when accessing IPU registers.
Check IPU clock and skip shutdown if clock is not enabled.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
U-Boot proper is using DM_MMC so, enable CONFIG_BLK otherwise
find_mmc_device failed to detect MMC device.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The soc_boot_modes array is only used by bmode command
and not needed in SPL. Don't include it into SPL.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
