Dealing with the sys ctrl register should touch only the
relevant bits and not accidently the whole register. On i.MX6,
the sys control register contains bits which shouldn't be reset to
0, e.g. SYS_CTRL[3-0] and IPP_RST_N (SYS_CTRL[23]).
Do this by read/modify/write instead of just a 32bit write.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1. No contents of "asm/arch/clk.h" is used within "dw_mmc.c".
2. If arch doesn't have "asm/arch/clk.h" driver won't build.
Without mentioned inclusion dw_mmc driver could be built for arches
other than ARM. For ARM driver still builds without it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fill the right command type when using CMD12 to stop data transfer.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
With CONFIG_SYS_64BIT_LBA, lbaint_t gets defined as a 64-bit type,
which is required to represent block numbers for storage devices that
exceed 2TiB (the block size usually is 512B), e.g. recent hard drives.
For some obscure reason, the current U-Boot code uses lbaint_t for the
number of blocks to read (a rather optimistic estimation of how RAM
sizes will evolve), but not for the starting address. Trying to access
blocks beyond the 2TiB boundary will simply wrap around and read a
block within the 0..2TiB range.
We now use lbaint_t for block start addresses, too. This required
changes to all block drivers as the signature of block_read(),
block_write() and block_erase() in block_dev_desc_t changed.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Current DWMMC driver used to give FIFO underrun/overrun error every 3rd time
for mmc rescan command.
In current code FIFO_DEPTH is getting calculated after reading the default FIFOTH
register and extracting the RX_WMARK bits from it i.e (RX_WMARK = FIFO_DEPTH/2 -1).
Instead of storing the correct value, we were recalculating the FIFO_DEPT each
time which is not correct.
Based on "[PATCH V9 3/9] DWMMC: Initialise dwmci and resolve EMMC read write issues"
http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/160247
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Enhance the MMC core to calculate the size of each MMC partition, and
update mmc->capacity whenever a partition is selected. This causes:
mmc dev 0 1 ; mmcinfo
... to report the size of the currently selected partition, rather than
always reporting the size of the user partition.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After waiting for the command completion event, the interrupt status
bits, that occured to be set by that time, are cleared by writing them
back. It is supposed, that it should be command related bits (command
complete and may be command errors).
However, in some cases the DMA already completes by that time before
the full transaction completes. The corresponding DINT bit gets set
and then cleared before even entering the loop, waiting for data part
completion. That waiting loop never gets this bit set, causing the
operation to hang. This is reported to happen, for example, for write
operation of 1 sector to upper area (block #7400000) of SanDisk Ultra II
8GB card.
The solution could be to explicitly clear only command related interrupt
status bits. However, since subsequent processing does not rely on
any command bits state, it could be easier just to remove clearing
of any bits at that point, leaving them all until all data processing
completes. After that the whole register will be cleared at once.
Also, on occasion, interrupts masking moved to before writing the command,
just for the case there should be no chance of interrupt between the first
command and interrupts masking.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since commit 48e0b2bd (powerpc/esdhc: Correct judgement for DATA PIO mode)
we see mx6 systems to hang after doing a 'save' command.
Revert this commit since the original 'ifdef' logic from 7b43db92
(drivers/mmc/fsl_esdhc.c: fix compiler warnings) was the correct one.
Reported-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch fixes a bug related to mmc writes.
When doing fatwrites on an SD-Card, MMC bus problems can occur. Depending
on the size of the file, "MMC0: Bus busy timeout!" is reported, resulting
in an SD-Card that is no longer responding.
It appears to be, that set_cluster can be called with a size being zero.
That can be with a file that has a size being an exact multiple
(including 0) of the clustersize, but also for files that are smaller than
the size of one cluster.
The same problem occurs if the "mmc write" command is given with a block
count being 0.
By adding a check for the block count being zero in mmc_write_blocks
(drivers/mmc.c), this problem is solved.
Signed-off-by: Ruud Commandeur <rcommandeur@clb.nl>
Cc: Tom Rini <trini@ti.com>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Mats Karrman <Mats.Karrman@tritech.se>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
CAP register don't have any information for 8-bit buswidth support
on 2.0 sdhci spec, only from 3.0 onwards bit[18] got this information.
Due to this misassignment in sdhci, mmc is setting 8-bit buswidth using
mmc_set_bus_width even if controller doesn't support.
Below change has code information.
"mmc: Properly determine maximum supported bus width"
(sha1: 7798f6dbd5)
Bug log: <mmc plus and emmc cards)
-------
zynq-uboot> mmcinfo
Error detected in status(0x208100)!
Device: zynq_sdhci
Manufacturer ID: fe
.....
So enable 8-bit support only for 3.0 spec using CAP and for below 3.0
assign mmc->host_caps = MMC_MODE_8BIT on respective platform driver
if host have a support.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch adds APIs to access(open / close) and to resize boot partiton of EMMC.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds FDT support for DWMMC, by reading the DWMMC node data
from the device tree and initialising DWMMC channels as per data
obtained from the node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enumerates dwmci and set auto stop command during
dwmci initialisation.
EMMC read/write is not happening in current implementation
due to improper fifo size computation. Hence modified the fifo size
computation to resolve EMMC read write issues.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The logic for the whether to configure for polling or DMA
was mistakenly reversed in this patch:
Commit 7b43db9211
drivers/mmc/fsl_esdhc.c: fix compiler warnings
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Sun Yusong-R58495 <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Faraday FTSDC010 is a MMC/SD host controller.
Although there is already a driver in current u-boot release,
which is modified from eSHDC and contributed by Andes Tech.
Its performance is too terrible on Faraday A36x SoC platforms,
so I turn to implement this new version of driver which is
10+ times faster than the old one.
It's carefully designed to be compatible with Andes chips,
so it should be safe to replace it.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The mpc85xx repuires a special layout on the memory device that is
connected to the eSDHC controller interface. But the file spl_mmc.c
didn't handle this specfic case, there needs a special treatmen, in
the powerpc drictory. So, there is no longer to keep spl_mmc.c on
mpc85xx, CONFIG_SPL_FRAMEWORK is not set.
When CONFIG_SPL_MMC_SUPPORT is set and CONFIG_SPL_FRAMEWORK is not
set, there was an error in drivers/mmc/spl_mmc.c:
drivers/mmc/libmmc.o:(.got2+0x8): undefined reference to `spl_image'.
Now, the solution is to move the file "spl_mmc.c" to directory "common/spl".
Signed-off-by: Ying Zhang <b40530@freescale.com>
add mmc card support with atmel mci driver
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Using IP version for different setting
- Higher version supports 8bit mode
- Higher version bus width setting is different
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs,
rename twl6035_mmc1_poweron_ldo by a more generic palmas_mmc1_poweron_ldo
function.
Signed-off-by: Nishanth Menon <nm@ti.com>
TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs
Rename twl6035 to palmas to allow reuse across multiple current and
future platforms
As part of this change, change the CONFIG_TWL6035_POWER to
CONFIG_PALMAS_POWER and update usage of header file accordingly.
Signed-off-by: Nishanth Menon <nm@ti.com>
A malloc() followed by memset() can be simply replaced by calloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If failed the add_host(), it is reasonable that return value of
add_sdhci().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Without this additional delay, some eMMC don't negotiate properly bus width
Tested on:
- Toshiba THGBM2G8D8FBAIB
- Toshiba THGBM4G4D1HBAR
- Micron MTFC4GMVEA (the one giving the problem)
- Hynix H26M64002BNR
- SanDisk SDIN5E1-32G
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Most of time that MMC driver spends on initializing a device is polling
OCR (operation conditions register). To decouple this polling loop,
device init is split into two parts: The first part fires the OCR query
command, and the second part polls the result. So the caller is now no
longer bound to the OCR-polling delay; he may fire the query, go
somewhere and then come back later for the result.
To use this, call mmc_set_preinit() on any device which needs this.
This can save significant amounts of time on boot (e.g. 200ms) by
hiding the MMC init time behind other init.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
log2 of the device block size serves as the shift value used to calculate
the block number to read in file systems when implementing avaiable block
sizes.
It is needed quite often in file systems thus it is pre-calculated and
stored in the block device descriptor.
Signed-off-by: Egbert Eich <eich@suse.com>
The number 512 appears quite a bit in the mmc code. Add a constant for this
so that it can be used here and in other parts of the code (e.g. SPL code
which loads from mmc).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
block_read returns unsigned long, so it doesn't make sense to check for
< 0. and neither does marking the header structure as const and then
casting away the constness to load data into it.
Also cleanup some unneeded pointer casting while we're at it.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Reviewed-by: Tom Rini <trini@ti.com>
The following headers are moved to a i.MX common location:
- regs-common.h
- regs-apbh.h
- regs-bch.h
- regs-gpmi.h
- dma.h
This way this header can be re-used also by other i.MX platforms.
For example the i.MX6 which will need it for the upcoming NAND
support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Support to check whether the SD3.0 or not.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Rommel Custodio <sessyargc@gmail.com>
eMMC vesrion is supported up to v4.5.
But bootloader isn't saw the exact eMMC version.
After applied this patch,
if use the mmcinfo command, then can see the exactly mmc version.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rommel Custodio <sessyargc@gmail.com>
Rework the waiting for transfer completion loop condition
to continue waiting until both Transfer Complete and DMA End
interrupts occur. Checking of DLA bit in Present State register
looks not needed in addition to interrupts status checking,
so it can be removed from the condition. Also, DMA Error
condition is added to the list of data errors, checked in the loop.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The cache should invalidate the read buffer for
the SD card interface after the transfer complete,
not command-complete.
Tested-by: Andrew Gabbasov <Andrew_Gabbasov@mentor.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Apparently, CONFIG_SYS_HZ must be 1000. Change this, and fix the timer
driver to conform to this.
Have the timer implementation export a custom API get_timer_us() for use
by the BCM2835 MMC API, which needs us resolution for a HW workaround.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Maximum bus width supported by some i.MX6 boards is not 8bit like
others. In case where both host controller and card support 8bit transfers,
they agree to communicate on 8bit interface while some boards support only 4bit interface.
Due to this reason the mmc 8bit default mode fails on these boards. To rectify this,
define maximum bus width supported by these boards (4bit). If max_bus_width is not
defined, it is 0 by default and 8bit width support will be enabled in host
capabilities otherwise host capabilities are modified accordingly.
It is tested with a MMCplus card.
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
cc: stefano Babic <sbabic@denx.de>
cc: Andy Fleming <afleming@gmail.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Gets rid of warnings from omap_gpio:
ERROR : check_gpio: invalid GPIO -1
(and undefined behaviour as the -1 error code is interpreted as gpio value)
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Let mmc_getcd() return true and mmc_getwp() false if mmc driver doesn't
provide handlers for them.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Add braces around first if test in each case to fix warning]
Signed-off-by: Tom Rini <trini@ti.com>
