Commit fe97471632 ("rockchip: rk3288: Allow setting up clocks in
U-Boot proper") fixes some clock issues when chainloading U-Boot on
rk3288 chromebooks. Part of that change is still available in veyron's
board_early_init_r() function. Since chain-loading U-Boot proper from
vendor firmware is possible on gru boards as well, do the same thing for
them too.
On rk3399, this needs to detect whether SPL was run via handoff, so
enable that and bloblist kconfigs it needs for chromebook_bob.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
- Add a new SMBIOS parser and enable it when booting from coreboot
- Fix up various driver names to avoid dtoc warnings
- Fully enable ACPI support on Google Chromebook Coral
- Add a way to set SMBIOS properties using the devicetree
- Update existing boards to use devicetree for SMBIOS using a new
default sysinfo driver
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This uclass is intended to provide a way to obtain information about a
U-Boot board. But the concept of a U-Boot 'board' is the whole system,
not just one circuit board, meaning that 'board' is something of a
misnomer for this uclass.
In addition, the name 'board' is a bit overused in U-Boot and we want to
use the same uclass to provide SMBIOS information.
The obvious name is 'system' but that is so vague as to be meaningless.
Use 'sysinfo' instead, since this uclass is aimed at providing information
on the system.
Rename everything accordingly.
Note: Due to the patch delta caused by the symbol renames, this patch
shows some renamed files as being deleted in one place and created in
another.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If u-boot gets used as coreboot payload it might be nice to get
vendor, model and bios version from smbios. I am not sure about
the output of all the read information.
With qemu target for coreboot this could look this:
CBFS: Found @ offset 14f40 size 3b188
Checking segment from ROM address 0xffc15178
Checking segment from ROM address 0xffc15194
Loading segment from ROM address 0xffc15178
code (compression=1)
New segment dstaddr 0x01110000 memsize 0x889ef srcaddr 0xffc151b0 filesize 0x3b150
Loading Segment: addr: 0x01110000 memsz: 0x00000000000889ef filesz: 0x000000000003b150
using LZMA
Loading segment from ROM address 0xffc15194
Entry Point 0x01110000
BS: BS_PAYLOAD_LOAD run times (exec / console): 77 / 1 ms
Jumping to boot code at 0x01110000(0x07fa7000)
U-Boot 2020.10-00536-g5dcf7cc590-dirty (Oct 07 2020 - 14:21:51 +0200)
CPU: x86_64, vendor AMD, device 663h
DRAM: 127.1 MiB
MMC:
Video: No video mode configured in coreboot!
Video: No video mode configured in coreboot!
Vendor: QEMU
Model: Standard PC (i440FX + PIIX, 1996)
Bios Version: 4.12-3152-g326a499f6f-dirty
Net: e1000: 52:54:00:12:34:56
eth0: e1000#0
No working controllers found
Finalizing coreboot
Hit any key to stop autoboot: 0
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Introduce maintainers file for the GE B1x5 board.
Cc: Huan 'Kitty' Wang <HuanWang@ge.com>
Cc: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This updates the PPD MAINTAINERS file doing a couple of changes:
* Replace Martyn with myself, since he no longer has the hardware
available and add Ian Ray as maintainer
* Fix the board directory path, which was still listing freescale/
instead of ge/
* Order the list of files alphabetically
* Add board specific device tree files to the file list
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This updates the Bx50v3 MAINTAINERS file, so that it also catches
changes to the related device tree files. Additionally the list of
files has been sorted alphabetically and I added myself as maintainer.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
GE B1x5v2 patient monitor series is similar to the CARESCAPE Monitor
series (GE Bx50). It consists of a carrier PCB used in combination
with a Congatec QMX6 SoM. This adds U-Boot support using device model
everywhere and SPL for memory initialization.
Proper configuration is provided as 'ge_b1x5v2_defconfig' and the
combined image u-boot-with-spi.imx can be flashed directly to 1024
byte offset to /dev/mtdblock0. Alternatively SPL and u-boot.imx can
be loaded separately via USB-OTG using e.g. imx_usb.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This separates the I2C specific code from the generic
GE vital product data code, so that the generic parts
can be used on hardware with VPD stored in SPI flash
memory.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
While this code is being used by all GE platforms its useful
to have it behind a config option for hardware bringup of
new platforms.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch provides information regarding the boot stage with using LEDs.
On the very beginning of U-Boot execution the GREEN LED is turned on.
When the execution is passed to Linux kernel the GREEN LED is off and
RED one is ON.
Afterwards, when Linux takes over the execution, the "heartbeat" driver
provides indication if the board is still alive.
Please also note that this patch uses {set|clr}bits_le32 macros as turning
ON GREEN LED is performed in a _very_ early stage of U-Boot execution
before DM_GPIOs are initialized.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When using cygwin64 "dd (coreutils) 8.26 Packaged by Cygwin (8.26-2)",
the last not 512bytes aligned data wat cut off and not burned into SD
card.
Saying the flash.bin size is 1085608 bytes, not 512bytes aligned. It only
burned 1085440 bytes, the leaving 168 bytes were not burnned and cause
boot issue.
So update README dd command to add "conv=notrunc"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
- New PX30 board: Engicam PX30.Core;
- Fix USB HID support for rock960;
- Remove host endianness dependency for rockchip mkimage;
- dts update for rk3288-tinker;
- Enable console MUX for some ROCKPi boards;
- Add config-based ddr selection for px30;
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
PX30.Core needs to mount on top of this Carrier board for creating
complete PX30.Core C.TOUCH 2.0 board.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board from Engicam.
PX30.Core needs to mount on top of this Evaluation board for
creating complete PX30.Core EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
The existing common code for Engicam boards uses i.MX6,
so attach that into i.MX6 Engicam boards so-that adding
new SoC variants of Engicam boards become meaningful.
Add support for it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Since sandbox's SPL is build with of-platadata, we should not use
U_BOOT_DEVICE() declarations as well. Drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX5rH/QAKCRDKSWXLKUoM
IRPAAJ9SvHR3w1qTc5W+Q5CWBUH5wJbNYQCaA4PpqZCdvyu1+nF5luL6JHhbDgw=
=hOd7
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-v2
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
Move board_fit_config_name_match() from Zynq/ZynqMP to common location.
This change will open a way to use it also by Microblaze and Versal.
Through this function there is a way to handle images with multiple DTBs.
For now match it with DEVICE_TREE as is done for Zynq.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove setting tapdelays for different speeds separately. Instead use
the ITAP and OTAP delay values which are read from the device tree.
If the DT does not contain tap delay values, the predefined values
will be used for the same.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Define timing macro's for all the available speeds of mmc. This is
done similar to linux. Replace speed macro's used with these new timing
macro's wherever applicable.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Call generic board_late_init_xilinx() to be aligned with the rest of xilinx
platforms. Also getting rid of initrd_high/fdt_high and use
bootm_low/boot_size instead.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add ram base address to scriptaddr env variable to make boot
script address to be a valid address when ddr base address changes.
This works properly if the first memory region is the region where uboot
runs. Also the solution was taken in respect of a lot of jtag script
putting u-boot script to certain address. For standard cases
bd->bi_dram[0].start is 0 all the time. Only for systems with DDR placed
out of this location it does calculation.
This is not the best solution and should be done differently in future but
enough for now till we don't have full solution ready yet.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot SPL on ZynqMP is using CONFIG_SPL_USE_TINY_PRINTF which doesn't
return any return value and all the time returns 0. That's why
even correct snprintf was returning in SPL chip ID as "unknown".
Change checking condition and allow snprintf to return 0 which is according
manual patch successful return.
"If an output error is encountered, a negative value is returned."
Fixes: 43a138956f7e ("arm64: zynqmp: Get rid of simple_itoa and replace it by snprintf")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix hex format from 0x%0X to 0x%0x to show correct numbers.
Fixes: fa793165da ("xilinx: zynqmp: refactor silicon name function")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Idea is to have something what can be used for board bringup from
generic board perspective.
There is a violation compare to spec that FRU ID is ASCII8 instead of
binary format but this is really for having something to pass boot and
boot to OS which has better generating options.
Also time should be filled properly.
For example:
fru board_gen 1000 XILINX versal-x-prc-01-revA serialX partX
There is also support for revision field which is Xilinx specific field.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for fru commands "fru capture" and "fru display".
The fru capture parses the FRU table present at an address and stores in a
structure for later use. The fru display prints the content of captured
structured in a readable format.
As of now, it supports only common header and board area of FRU. Also, it
supports only English language code and ASCII8/BINARY formats.
fru_data variable is placed to data section because fru parser can be
called very early before bss is initialized. And also information needs to
be shared that's why it is exported via header.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no need to reference files in common folder back. Simply adding
Makefile to this folder does the job because this "common" location is
already wired in main Makefile.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
