Switch to explicitly using the Pro variant DT, which has been
available since Linux 4.11.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Migrate the values for ENV_SIZE and ENV_OFFSET into board specific
Kconfig defaults so they're more accessible for configuration.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Add reasonable default SPI offsets and ENV size when configured to
boot from SPI flash.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Unify the location of DT selection into board_late_init instead of
split between detection and static configuration paths.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
The mPCIe slots on ClearFog Pro and ClearFog Base may be alternately
configured for SATA usage.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
While newer Linux kernels provide autoconfiguration of SFP, provide
an option for setting in U-Boot Kconfig for use prior to booting.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Add a unique entry for ClearFog Base variant, reflected in the board
name and adjusted SerDes topology.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Make the board version printed indicate the Pro variant default.
Also adjust static name casing to match what is expected for
EEPROM product name to share string constants.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch enables the guardian board to provide feedback
about the boot stage in headless mode. The on-board led
would behave in the following pattern
* U-boot -> GLOW LED
* Linux -> BLINK LED [HEART-BEAT PATTERN]
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
For some layouts it is necessary to adjust the CK_DELAY parameter to
successfully complete DDR training. Add the ability to specify the
CK_DELAY in the mv_ddr_topology_map.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Pull in changes that have been pending in our 'next' branch. This
includes:
- A large number of CI improvements including moving to gcc-9.2 for all
platforms.
- amlogic, xilinx, stm32, TI SoC updates
- USB and i2c subsystem updtaes
- Re-sync Kbuild/etc logic with v4.19 of the Linux kernel.
- RSA key handling improvements
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
-----BEGIN PGP SIGNATURE-----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=PiOt
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200406' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic into next
- clk: meson-g12a: missing break
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
This fixes the issue when PHY auto negotiation never completes.
Fixes: 431cd76dd8("colibri_imx6: migrate to DM_ETH")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Parameter order is not correct based on zynqmp_mmio_write() declaration.
Fixes: be52372ff1 ("arm64: zynqmp: Use zynqmp_mmio_read/write functions")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Delay required for clock propagation is tighly coupled with initialization
done in psu_init(). That's why call it also for u-boot proper with
CONFIG_ZYNQMP_PSU_INIT_ENABLED enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_early_init_f() is the right location where debug uart can be
configurated (after MIO initialization).
The patch is taking this call from SPL to also make it available for U-Boot
proper.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP mini configurations works without PMU firmware that's why there is
no reason to enable the driver and check if it was probed properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Multi boot register can be used for using different boot images and design
better boot strategy. Let EL3 SPL or U-Boot to read it and print it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the Amlogic based libretech-pc platform.
This platform comes with 2 variant, based on the s905d or s912 SoC.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: update board/amlogic/q200/MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Jetson Nano Developer Kit is a Tegra X1-based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4GB
of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot
used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. NVMe support
has also been added. Env save is at the end of QSPI (4MB-8K).
A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
T210 CBoot is now doing the full pinmux and GPIO init, based on the DTB
tables. Remove pinmux/GPIO init tables & code from all T210-based builds
below:
p2371-2180 aka TX1
p2371-0000
e2220-1170
p2571
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
compatibility with stm32mp15_dhcom_basic_defconfig
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl6EiK0ACgkQ4rK92eCq
k3V6DggAhU7jE5MGs9A7En+YpANXbJ4tl56IZIjdzPzEjA2G3yuBv/DLci/w27aF
eaP83ayI/ZrVtevEBFomP0JRrzQc9r/ot+USVugGsoAigLbzJc5uba42FGn09Olh
uKkst0Fb7uPRzZQNwRc7hTKVSLvT11c0oPQyhhJM2djPDTETDry+RPnEFQ41SEUt
bNILmj0VRzikzbe5RXFWWYMUWBrt22pG2LLhog+WSRSpqrWM2zES64NnwAXxD/mR
YIQFZIZ6eWW2Otp+qzenkg5ZWIMVWRyUBAP5e0auKRE8TGWAXgBcoFRTRLf7oA/P
yr3TTBMWiPdqdXNe3MYzAiTpm7jrtg==
=RALH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200401' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Fix device tree of Avenger96 board from Arrow Electronics and add
compatibility with stm32mp15_dhcom_basic_defconfig
Use DT /aliases node to establish a stable phandle to the configuration
EEPROM. This permits the configuration EEPROM to be moved e.g. to a
different address or a different bus. Adjust the board code to handle
new phandle lookup.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
If the DM_ETH is enabled, the board-specific ethernet registeration
should be disabled, make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add code to reset the board through PMIC, by writing the required
PMIC registers in the CPU reset handler.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add config to enable the PFE and ETH support.
Also change the pfe secure boot header address.
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The SDHC1_DAT4 signal could be routes to SDHC1_VS or SDHC1
adapter slot for SDHC1 usage. When SDHC1 is selected in RCW,
do not force to route it to SDHC1 adapter slot if find it
has already been configued for SDHC1_VS.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Set VID to 800 mV for Rev1 and set VID as per switch settings
for Rev2.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Program GIC LPI configuration table:
1. Redistributor PROCBASER configuration table (which
is common for all redistributors)
2. Redistributor pending table (PENDBASER), for all the
available redistributors.
Signed-off-by: Manish Tomar <manish.tomar@nxp.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update "board_fix_fdt" with correct counter value "i".
This will fix the issue while fetching the "reg_names"
resource from fdt after fixup.
Signed-off-by: Vikas Singh <vikas.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Since commit 8e9a8d0d0c ("rockchip: elgin-rv1108: use board_early_init_f
for per-boar init") the function that configure the board GPIOs is no
longer called since CONFIG_BOARD_EARLY_INIT_F=y is not selected.
These GPIOs do not need to be configured in such early stagem, so change it
to rk_board_late_init() and also select CONFIG_BOARD_LATE_INIT=y
to fix the regression.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use syscon API to get grf base instead of get from dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use syscon API to get grf base instead of get from dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Need to increase the LPDDR2/LPDDR3 the voltage vdd2_ddr: buck2
form 1.2V to 1.25V for 32bits configuration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Display the reference MBxxxx found in OTP49
only for STMicroelectronics boards when CONFIG_CMD_STBOARD
is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
# Conflicts:
# board/st/stm32mp1/stm32mp1.c
Update the command stboard to support the updated coding of OTP 59 with
finished good.
The ST product codification have several element
- "Commercial Product Name" (CPN): type of product board (DKX, EVX)
associated to the board ID "MBxxxx"
- "Finished Good" or "Finish Good" (FG):
effective content of the product without chip STM32MP1 (LCD, Wifi, …)
- BOM: cost variant for same FG
(for example, several provider of the same component)
For example
- commercial product = STM32MP157C-EV1
- Finished Good = EVA32MP157A1$AU1
Booth information are written on board and these information is also saved
in OTP59:
bit [31:16] (hex) => Board id, MBxxxx
bit [15:12] (dec) => Variant CPN (1....15)
bit [11:8] (dec) => Revision board (index with A = 1, Z = 26)
bit [7:4] (dec) => Variant FG : finished good (NEW)
bit [3:0] (dec) => BOM (01, .... 255)
The updated command is:
stboard [-y] <Board> <VarCPN> <Revision> <VarFG> <BOM>
And the displayed STMicroelectronics board identification is:
Board: MB<Board> Var<VarCPN>.<VarFG> Rev.<Revision>-<BOM>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Lock the OTP used for board identification for the ST boards after
programming.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Read the value directly from the OTP and no more of the shadows
to avoid the need of reboot after stboard command to have correct value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Update management of misc_write, which now return length of data
after the commit 8729b1ae2c ("misc: Update read() and write()
methods to return bytes xfered")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
K3 J721E:
* OSPI boot support
* Support for loading remote cores in R5 SPL
* PMIC ESM Support
* Minor fixes for R5F and C7x remoteproc drivers
K3 AM654:
* Update AVS class 0 voltages.
* Add I2C nodes
DRA7xx/AM57xx:
* Fixed Android boot on AM57xx
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
As there is only one mx31pdk config file and with upcoming updates to
the Kconfig parsing logic, rather than have an entry in
board/freescale/mx31pdk/Kconfig, move this single setting to the
defconfig file.
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Magnus Lilja <lilja.magnus@gmail.com>
In a few places we have Kconfig entries that set SPL_LDSCRIPT to what is
the default value anyways. Drop these.
Cc: Michal Simek <monstr@monstr.eu>
Cc: Rick Chen <rick@andestech.com>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com> (for Microblaze)
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Instead of resetting the ethernet phy through functions in imx8mq_evk.c, let the
driver reset the phy via dts description adding a reset duration of 10 ms
following atheros 8031's datasheet recommendation.
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Convert imx6sabresd ethernet to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On the aristainetos2c boards the PMIC needs to be initialized,
because the Ethernet PHY uses a different regulator that is not
setup per hardware default. This does not influence the other
versions as this regulator isn't used there at all.
Signed-off-by: Heiko Schocher <hs@denx.de>
The OP-TEE binary to use is renamed to v2 as the v1 binary has been
deprecated and is no longer built by default.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Add entries for the newly created documentation files in reST
format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Convert README to reStructuredText format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: spell out U-Boot correctly]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add initial support for the ABB SECU board, which is an ArriaV-based
SoCFPGA system with ethernet and booting from Denali NAND.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Now k3-image-gen[0] is the official repository for generating sysfw.itb
Update the same in AM65x and J721e README.
[0] https://git.ti.com/cgit/k3-image-gen/k3-image-gen/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Fix building errors if CONFIG_DM_VIDEO is enabled. This is the only
u-boot board that enables CONFIG_AM335X_LCD and from which I started
to develop the version of the frame buffer driver that supports the
driver model.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Initialize both ESM and ESM_PMIC support if available for the board.
If support is not available for either, a warning is printed out.
ESM signals are only properly routed on PM2 version of the J721E SOM,
so only probe the drivers on this device.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Change plain test README to rst format and move this file
in documentation directory.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
DEVICE_TREE variable is not exported from dts/Makefile that's why it is
necessary to setup directly before use.
Fixes: 312f2c5b14 ("arm: xilinx: Use device tree which can be passed on cmd line")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The board has two push button connected to MIO pins
50 and 51, which have a pull-down resistor and are
connected to 1.8V when pressed.
These two pins are wrongly initialized with internal
pull-up enabled so they are reported as 1 all the time
with no change when pressed.
Disable the internal pull-up to fix the issue.
Signed-off-by: Milan Obuch <u-boot@dino.sk>
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added support for onboard LED's and push button. When powered board will be
in low power mode(yellow LED), on button press, board enters full power mode
(red LED) and boots u-boot.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
roc-pc-rk3399 board has one user button & three user LED's. Currently
we don't have any code support for these devices. Since button and LED's are
specific to roc-pc-rk3399 board, split it into its own board file and add code
support here.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl5GcB0ACgkQ4rK92eCq
k3Wr9gf/dDPJi6UBhLDio/IVKDBddOEUN0Lwdr9W0upL+DrdvEOyNyMSEKuLccIE
UTd1NmNNwcvgDRaPvB5o3R7twWItTW0cYlmVkFSZ228aq6xdf/SElN2OUD6B9Gh+
8bi6oVLu41TNMYn4VYxsEftcT2megfH8s+SH/FlvR5ua1yCC1vyrytEQjPIbJAB2
sa90ewDyp5EYqGLdAk6AVjPLeNZsaleGwuyLf04PoC2xhn+3HTEKJCJN4O46aJUr
0GUI7YN7pTjIfZdYfFqjcwoQV1xV2HtbjCTcOb8Td8TEYjIoILF8tSyfIwDXWGB5
zMQIQxUdQyNiqdBPFcnkAufjk+zLIQ==
=0dG+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200214' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
Change the dfu functions dfu_otp_read and dfu_pmic_read to static,
this patch avoids warning when compiling with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add include for dfu, add prototype for set_dfu_alt_info
and avoid warning when compiling with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update readme:
- list the supported SOC and change family to STM32MP15x
- add warning on OTP write and prerequisite:
check if MAC address is not yet provisioned.
- Use filesize for mmc write command (avoid to write all partition
with ${partsize}). ${filesize} and ${partsize} are set by previous
load command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
On am571x-idk there can be following configurations based on Jumper J51
and LCD panel detected.
1) J51 removed (6port): 6 port Ethernet. Disable LCD panel.
2) J51 placed (LCD) + Panel detected: 4 port Ethernet with appropriate LCD.
3) J51 placed (LCD) + Panel not detected/not supported.
Configuration 3 is considered invalid as we can't use display nor ICSS1
ethernet ports due to hardware muxing. Alert the user to fix the
configuration and prevent boot.
Alternative was to allow boot and limit to 4 port Ethernet with no display
but this involved introduction of another DTB for the kernel and was
considered not worth the hassle.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
It's a very rare if at all existing occasion when ARC CPU template
is used as is w/o any changes - in the end it's a beauty and competitive
advantage of ARC cores to be tailored for a particular use-case - and
so it doesn't make a lot of sense to offer template-based "-mcpu" selection.
Given for each and every platform we end-up adding quite a few more flags
it's logical to move "-mcpu" selection to platform's definition as well
which we exactly do here.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Given now nsim_hs38 configuration is usable on QEMU and in QEMU
we have Virtio working perfectly fine the next logical step
is to add support of supported & known to work net & bkl to this
config.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
Drop PPD_UART_PAD_CTRL since it matches defaults.
Enable DM serial and MXC uart.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Add backlight and panel devicetree definitions
Use UCLASS_PANEL to enable backlight via display enable handler
Remove old explicit gpio code for handling backlight
Use cls command to initiate display in HW agnostic manner
Enable DM regulator and pwm
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Enable DM_VIDEO for mx53ppd.
Enable DM_REGULATOR_FIXED and DM_PWM for the backlight.
Remove unused MX53PPD_LCD_POWER.
Remove old (incorrect) setup_iomux_lcd.
Enable backlight via display enable handler.
Use cls command to initiate display in HW agnostic manner.
Modify `failbootcmd' to use lcdputs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Remove old (pre-DM) i2c setup code.
Enable DM i2c.
Convert common code to use DM rtc.
Convert common code to read VPD from eeprom partition.
Convert the generic i2c PMIC init code to use the new da9063 driver.
mx53ppd only:
Correct RTC compatible in device tree.
Enable MXC DM i2c driver.
Define CONFIG_SYS_MALLOC_F_LEN so that DM is available in pre-reloc.
Make GPIO banks available during preloc, since initialisation is done
in board_early_init_f().
Add gpio_request() calls to satisfy the DM_GPIO compatibility API.
Remove unused power configuration.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
This should help keeping the screen black when booting the kernel.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Convert imx6sabresd PCI to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_PCI Please update
the board to use CONFIG_DM_PCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
After the conversion the following commands were used for testing:
=> pci enum
PCI: Failed autoconfig bar 10
PCI: Failed autoconfig bar 10
=> pci 1
Scanning PCI devices on bus 1
BusDevFun VendorId DeviceId Device Class Sub-Class
Reviewed-by: Fabio Estevam <festevam@gmail.com>
commit 88718be300 ("mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND")
moved CONFIG_NAND -> CONFIG_MTD_RAW_NAND. Adapt board code to this
change, as last merge did not respect the above commit.
Signed-off-by: Heiko Schocher <hs@denx.de>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Explicitly configure GPIO0_0 in SPL, which controlls 3V3 voltage
on the XEA board (it also supplies TIVAs).
This code would enable TIVAs power supply early (also when board
uses the falcon boot).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The 'local-mac-address' property needs to be adjusted to the MAC address
value stored in U-Boot's 'ethaddr' env variable.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Currently there are two targets for the i.MX6SX SabreSD board:
mx6sxsabresd_defconfig and mx6sxsabresd_spl_defconfig.
This brings additional maintainance effort without a clear
advantage.
Keep only the mx6sxsabresd_defconfig one and remove
mx6sxsabresd_spl_defconfig to keep it simpler.
Also remove the SPL related code from the board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Assign Igor Opaniuk as a board maintainer.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add README with build steps for U-boot and TF-A for Verdin iMX8M Mini SoM.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad
2GB WB IT V1.0A module. They are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports booting from the on-module eMMC only, SDP support is disabled
for now due to missing i.MX 8M Mini USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
Normal Boot
Trying to boot from MMC1
NOTICE: Configuring TZASC380
NOTICE: RDC off
NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty
NOTICE: BL31: Built : 01:11:41, Jan 25 2020
NOTICE: sip svc init
U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Reset cause: POR
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial#
06535149
Net: eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
Verdin iMX8MM #
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add support for storing configuration for Verdin iMX8M Mini and
Nano SoMs in Toradex config block.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add support for storing configuration for Apalis iMX8X SoM
in Toradex config block.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Assign Alex Nemirovsky as custodian for all
Cortina Access (CA) for ARM and MIPS based SoCs.
Currently Cortina Access CAxxxx family of SoCs support both
ARM and MIPS ISA. Drivers have cross platform support for
both architectures.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Most files don't need this header and it pulls in quite of lots of stuff,
malloc() in particular. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This function is actually intended to read a string rather than a
property. All of its current callers use it that way. Also there is no way
to return the length of the property from this function.
Rename it to better indicate its purpose, using ofnode_read as the prefix
since this matches most other functions.
Also add some tests which are missing for these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Inside Kconfig we must not use the CONFIG_ prefix with the imply statement.
Fixes: 28e3c39e53 ("board: freescale: ls1012a2g5rdb: enable network
support on ls1012a2g5rdb")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1021A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1012A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support of "qixis_reset emmc" command for lx2160a based platforms
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Coreutils command nproc can be used on Linux and BSD to count the number of
available CPU cores. Use this instead of relying on the parsing of the
Linux specific proc file system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
XOM pins provide information for iROM bootloader about the boot device.
Those pins are mapped to lower bits of OP_MODE register (0x10000008),
which is common for all Exynos SoC variants. Set the default MMC device id
to reflect the boot device selected by XOM[7:5] pins (2 for the SD or 0 for
the eMMC).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
There is a typo in meerkat96 MAINTAINERS email address. Fix it.
Reported-by: Carl Gelfand <carl@novtech.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:
- Gigabit Ethernet via external RTL8211E Ethernet PHY
- 16 MiB SPI NOR flash memory
- PoE tap header
- Line out jack removed
Only H5 variant test samples were made available, and the vendor is not
certain whether other SoC variants would be made or not. Furthermore the
board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree
simply includes the one for the ALL-H3-CC, and adds the changes on top.
The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.
The board features:
- H2, H3, or H5 SoC from Allwinner
- 2 DDR3 DRAM chips
- Realtek RTL8821CU based WiFi module
- 128 Mbit SPI-NOR flash
- micro-SD card slot
- micro HDMI video output
- FPC connector for camera sensor module
- generic Raspberri-Pi style 40 pin GPIO header
- additional pin headers for extra USB host ports, ananlog audio and
IR receiver
Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.
The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function related to timer and most of the timer functions are in
time.h, so move this function there.
Signed-off-by: Simon Glass <sjg@chromium.org>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions relate to setting up the device tree for booting the OS.
The fdt_support.h header file supports similar functions, so move these
there.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is an init function so move it out of the common header. Avoid using
the typedef so that we don't have to include the global_data header file.
Also tidy up the function style in comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix loop in board_fix_fdt that erroneously increments the counter
in all cases whereas the counter should be incremented only if a
matching string has been found.
Fixes: 5d535aa40b ("board: fsl: lx2160a: implement board_fix_fdt")
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LS1028A board code uses arch_misc_init to set up the board mux
on QDS. Move this code to misc_init_r. This is consistent with LS gen 2
and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS108x SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS2 SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LX2 board code uses arch_misc_init to set up the board mux on
RDB and QDS. Move this code to misc_init_r. This is consistent with LS
gen 2 and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The dts node of the DSPI controller in kernel is spi instead of dspi,
it is not correct if use "/soc/dspi@" to fix up the status of the dts
in kernel, so, modify it to "/soc/spi@".
The DSPI2 and I2C5 are muxed, and the status of DSPI2 node in kernel dts
default value is okay, So set the status of DSPI2 node in kernel dts to
disabled if it is muxed as I2C5.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Passes on the primary address used by u-boot to Linux. The code does a DT
fix-up for ENETC PFs and sets the primary MAC address in IERB. The address
in IERB is restored on ENETC PCI functions at FLR.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This board is similar to SUV31, but the FPGA is reset concept is quite
different.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds the possibility in both debug and ramfs modes to
optionally load an env file from /tftpboot/$tftppath (this is ignored if
not present, so the change is backward compatible). This gives the debug
and ramfs scripts the possibility to set uboot environment variables
that were previously asked the users to manually set (nfs path in debug
and rootfs size in ramfs).
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Tom Rini <trini@konsulko.com>
The tftppath was not set in case of run ramfs. It worked only by chance
if was already set before.
Also check the boardname before setting the tftppath for COGE5.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Tom Rini <trini@konsulko.com>
The CPUWD reset reason is used for kmp204x.
And the qrio cpu reset request is configured to operate in
core reset mode.
But for the evaluation of the qrio's reset reason register
the CPUWD figures as a unit reset source rather than a core
reset source. This patch defines the CPUWD reset as a core
reset source when evaluating the reset reason register.
Signed-off-by: Rainer Boschung <rainer.boschung@ch.abb.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
This patch moves the qrio and i2c deblocking code to
keymile/common as it will also be used by the upcoming CENT2 board.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
This prevents the board from booting which is not the expected behavior.
Signed-off-by: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
This add the initial support of the broadcom reference
board bcm968360bg with a bcm68360 SoC.
This board has 512 MB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Since commit 4213609cc7 ("drivers: core: use strcmp when find device by
name") one has to provide full name to get requested object. Fix the code
used to detect enable power regulators on the supported Exynos boards to
use proper PMIC device device name then.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since commit 4213609cc7 ("drivers: core: use strcmp when find device by
name") one has to provide full name to get requested object. Fix the code
used to detect Odroid board revision to use proper ADC device name then.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The ST-Ericsson U8500 SoC has been used in mass-production for
some Android smartphones released around 2012.
In particular, Samsung has released more than 5 different
smartphones based on U8500, e.g.
- Samsung Galaxy S III mini (GT-I8190) "golden"
- Samsung Galaxy S Advance (GT-I9070) "janice"
- Samsung Galaxy Xcover 2 (GT-S7710) "skomer"
and a few others.
Mainline Linux has great support for the Ux500 SoC, so these
smartphones can also run Linux mainline quite well.
Unfortunately, the original Samsung bootloader used on these devices
has limitations that prevent booting Linux mainline directly.
It keeps the L2 cache enabled, which causes Linux to crash very early,
shortly after decompressing the kernel.
Using U-Boot allows to circumvent these limitations. We can let the
Samsung bootloader chain-load U-Boot and U-Boot locks the L2 cache
before booting into Linux. U-Boot has several other advantages
- it supports device-trees directly and we are no longer limited to
flashing Android boot images through Samsung's proprietary download
mode.
The Samsung "stemmy" board covers all Samsung devices based on U8500.
Add minimal support for "stemmy". For now only UART is supported but
this will be extended later.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Clearfog Base carrier uses serdes lane #5 as USB host. Use EEPROM stored
device identification to configure the serdes accordingly when
available.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Select the serdes configuration table based on the platform identity
read from EEPROM TLV data. Clearfog GTR needs a slightly different
serdes configuration.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Set the kernel device-tree file (fdtfile environment variable) based on
run-time detection of the platform.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Read RAM die capacity from the EEPROM TLV.
Follow the ONIE standard that defines the Vendor Extension entry type
for vendor specific data. We have no Private Enterprise Number at the
moment as the standard requires. Use the dummy all 0xff value for now.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Enabled both DDR clock signals to support Clearfog variants (currently,
Clearfog GTR) that need both clocks.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/toradex/colibri-imx8x/colibri-imx8x.c:104:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/toradex/apalis-imx8/apalis-imx8.c:92:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/freescale/imx8qxp_mek/imx8qxp_mek.c:115:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/freescale/imx8qm_mek/imx8qm_mek.c:102:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/advantech/imx8qm_rom7720_a1/imx8qm_rom7720_a1.c:110:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Include fdt_support.h header file to fix the following sparse warning:
board/freescale/imx8qm_mek/imx8qm_mek.c:116:5: warning: no previous
prototype for ‘ft_board_setup’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Include fdt_support.h header file to fix the following sparse warning:
board/freescale/imx8qxp_mek/imx8qxp_mek.c:129:5: warning: no previous
prototype for ‘ft_board_setup’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Functions spl_dram_init() and power_init_board() are used only in
the scope of this file, so make them static to fix the following sparse
warnings:
board/freescale/imx8mm_evk/spl.c:40:6: warning: no previous prototype
for ‘spl_dram_init’ [-Wmissing-prototypes]
board/freescale/imx8mm_evk/spl.c:85:5: warning: no previous prototype
for ‘power_init_board’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Add sys_proto.h header file to fix the following sparse warning:
board/freescale/imx8mm_evk/imx8mm_evk.c:59:5: warning: no previous
prototype for ‘board_mmc_get_env_dev’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
The imx8mm doesn't require the hdmi firmware.
Update also the fw version.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
With commit 0d52bab462 ("mx7dsabre: Enable DM_ETH")
Device Tree has been update and change pfuze3000 node
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support.
The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier
board has Ethernet, USB host port, USB OTG port.
Signed-off-by: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The PFUZE100 and PFUZE200 PMICs can be discerned by bit 0 in DeviceID
register. Print the correct identification of the PMICs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Simplify the uSDHC4 eMMC controller setup. This is the only eMMC
present on the system and only controller that is used, so drop
the extra logic.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Not finding a node that we try to disable does not always need to be
fatal to boot but should at least print out a warning. Return error
from fdt_disable_node as it did fail to disable the node, but only
warn in the case of disabling the TRNG as this will not prevent boot.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The TI J721E EVM system on module (SOM), the common processor board, and
the associated daughtercards have on-board I2C-based EEPROMs containing
board config data. Use the board detection infrastructure to do the
following:
1) Parse the J721E SOM EEPROM and populate items like board name, board
HW and SW revision as well as board serial number into the TI common
EEPROM data structure residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing associated I2C
addresses used for on-board EEPROMs containing daughter card-specific
data. If such a card is found, parse the EEPROM data such as for
additional Ethernet MAC addresses and populate those into U-Boot
accordingly
3) Dynamically apply daughter card DTB overlays to the U-Boot (proper)
DTB during SPL execution
4) Dynamically create an U-Boot ENV variable called name_overlays
during U-Boot execution containing a list of daugherboard-specific
DTB overlays based on daughercards found to be used during Kernel
boot.
This patch adds support for the J721E system on module boards containing
the actual SoC ("J721EX-PM2-SOM", accessed via CONFIG_EEPROM_CHIP_ADDRESS),
the common processor board ("J7X-BASE-CPB"), the Quad-Port Ethernet
Expansion Board ("J7X-VSC8514-ETH"), the infotainment board
("J7X-INFOTAN-EXP") as well as for the gateway/Ethernet switch/industrial
expansion board ("J7X-GESI-EXP").
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use dm_i2c_probe() rather than i2c_get_chip() when trying to access
board-detection EEPROM devices. This has the advantage of more gracefully
handling the case when the EEPROM is not present by allowing to exit the
function early rather than failing and outputting an error message on the
I2C transactions that follow.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
These are necessities for beaglebone ai boot. There is the addition of
CONFIG_SUPPORT_EMMC_CONFIG to the Kconfig file. This is present upstream
but not in 19.01 yet.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch configures the pinmux settings for the BeagleBone AI after
the emmc read has completed.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
BeagleBoard.org BeagleBone AI rev A1 does not include a board
identifier I2C EEPROM due to a design oversight. These boards have
been put into production and are generally available now.
The board identifier information, however, has been included in the
second eMMC linear boot partition (/dev/mmcblk1boot1).
This patch works by:
* First, looking for a board identifier I2C EEPROM and if not found,
* Then seeing if the boot mode matches BeagleBone AI with eMMC in the
boot chain to make sure we don't enable eMMC pinmuxes on boards
that don't support it, and
* Finally, initializes the eMMC pins and reading the header.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function related to timer and most of the timer functions are in
time.h, so move this function there.
Signed-off-by: Simon Glass <sjg@chromium.org>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions relate to setting up the device tree for booting the OS.
The fdt_support.h header file supports similar functions, so move these
there.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is an init function so move it out of the common header. Avoid using
the typedef so that we don't have to include the global_data header file.
Also tidy up the function style in comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Split the board and SOC support for STM32MP15x family and
prepare the introduction of new boards with STM32MP15x.
This path define the 2 configurations:
- STM32MP15x: STM32MP15x soc support (new)
- TARGET_ST_STM32MP15x: STMicroelectronics board support (choice)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move CONFIG_ENV_SECT_SIZE and CONFIG_ENV_OFFSET in stm32mp15_*_defconfig
for ST board with NOR support (STM32MP15xx-EV1 boards)
- CONFIG_SECT_SIZE values = the max supported NOR erase size (256KB)
- CONFIG_ENV_OFFSET = offset for NOR (ENV_IS_IN_SPI_FLASH)
This Patch prepares the U-Boot support of boards with STM32MP15x SOC
not provided by STMicroelectronics.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the ST command in board/st/common, as this command is only used
by ST board. Prepare the support in U-Boot of boards with STM32MP15x
SOC but not STMicroelectronics.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Clearfog: Fix SD booting (Baruch)
- Misc updates to MMC handling in SPL to support booting from
main data partition (vs hardware boot partition) on MVEBU (Baruch)
This adds a general board file based on MT7622 SoCs from MediaTek.
This commit is adding the basic boot support for the MT7622 rfb.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
This adds a general board file based on MT8512 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8512 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
SPL now automatically selects the correct U-Boot image offset for both
eMMC and SD card. No need to tweak
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR anymore.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently the following SPL hang is observed:
U-Boot SPL 2020.01-rc5-00079-g797eee36a1 (Jan 06 2020 - 11:24:09 -0300)
Trying to boot from MMC1
Card did not respond to voltage select!
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Fix it by moving the eSDHC2 initialization to SPL.
While at it, since this board uses DM_MMC all the esdhc board
code can be removed to make the code simpler.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Only the wandboard revD1 boards have PMIC, so when running on a wandboard
of different revision the following error is always shown on every boot:
pmic_get() ret -19
Instead of printing this error message, move it to debug level instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This patch adds new jtag distro boot command to look for bootscript
file in DDR and execute it first incase of jtag bootmode.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DEVICE_TREE variable has been added by commit 6ab6b2afa0
("dts: re-write dts/Makefile more simply with Kbuild")
where DT can be specified on command line. If it is not then
CONFIG_DEFAULT_DEVICE_TREE is used to ensure backward compatibility.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Names have to match device tree file names. Also add missing one.
Fixes: 50d9283347 ("arm64: zynqmp: Sync names for SC with Versal")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to do serial initializationin low level code. Uart
driver does it already based on DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to do serial initialization. Uart driver does it already
based on DT. Good effect is that it is clear which interface is console.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
MIO34 is connected to POWER_KILL signal. When MIO configuration is done in
psu_init() and this pin is assigned to PMU but PMU configuration is not
loaded yet. PMU gpio output is high that means board is powered off
immediately.
The patch is fixing this sequence that MIO34 stays assing to ps gpio IP.
PMU config is loaded in SPL and then pin assigned to PMU through
psu_post_config_data().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
OF_BOARD and OF_SEPARATE can use board specific board_fdt_blob_setup().
OF_BOARD option is mostly used for picking up DTB from certain location.
OF_SEPARATE option is used when DTB is appended after u-boot binary.
This board specific function is aligned with current version in
lib/fdtdec.c with checking CONFIG_XILINX_OF_BOARD_DTB_ADDR address first.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The reason for this change is just get in sync with board_fdt_blob_setup()
available at lib/fdtdec.c.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently "script_offset_f" env variable is hardcoded, this variable
specifies from which offset of the flash boot.scr should be read/write.
As flashes are of different sizes having a fixed offset makes it
difficult to load other images into the flash which may overwrite the
boot script or cannot utilize the full memory. This current fix
creates a new config "CONFIG_BOOT_SCRIPT_OFFSET" which holds the
offset address, overwrites the "script_offset_f" variable.
Also removed existing variable with default values, as the default
values are held by CONFIG_BOOT_SCRIPT_OFFSET
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Emmc boot devcie is mounted to mmc@ff160000 controller on zynqmp.
Detect mmc alias at run time for setting up proper boot_targets
sequence instead of setting boot_targets manually.
Removed setting "modeboot" variable as it not longer need as we
switched to distro boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Emmc boot devcie is mounted to sdhci@f1050000 controller on versal, while
in emmc boot mode, boot tragets are set to mmc0. So removed mmc0 and using
the dev seq number from the sdhci@f1050000 controller.
Dev seq number is setup based on DT aliases that's why needs to be setup at
run time.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
For upcoming SECU board we have different MAC address offsets depending
on which functional unit we are running. In this case we need to pass
this value to the ivm_populate_env function instead of using the hard
coded config option there.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch only fixes a typo.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
All platforms currently use the "MCFTMR" DMA timer rather than the PIT
timer, so drop the MCFPIT code.
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Cc: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
-----BEGIN PGP SIGNATURE-----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=SjPV
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc1
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
-----BEGIN PGP SIGNATURE-----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=rkHZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200108' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- Khadas VIM3L based on Amlogic S905D3 support
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
Add board_mmc_get_env_dev, otherwise,
Loading Environment from MMC...
MMC Device 0 not found
*** Warning - No MMC card found, using default environment
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
After the conversion to DM_PMIC the following output is seen:
PMIC: PMIC: PFUZE100 ID=0x10
Remove the unnecessary PMIC string from the board file to
avoid the repetead string.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Commit ec837c82d7 ("imx6: wandboard: convert to DM_PMIC")
caused the following pmic_get() error:
CPU: Freescale i.MX6QP rev1.0 at 792 MHz
Reset cause: POR
DRAM: 2 GiB
PMIC: pmic_get() ret -19
...
and since the PMIC presence is used to determine the board D1 revision,
the following error is seen when booting a board rev D1:
WARNING: Could not determine dtb to use
and the kernel does not boot at all.
Fix the regression by passing "pfuze100@8" as the correct parameter
to the pmic_get() function in the DM case.
Fixes: ec837c82d7 ("imx6: wandboard: convert to DM_PMIC")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add support for the EFI_RNG_PROTOCOL routines for the qemu arm64
platform. EFI_RNG_PROTOCOL is an uefi boottime service which is
invoked by the efi stub in the kernel for getting random seed for
kaslr.
The routines are platform specific, and use the virtio-rng device on
the platform to get random data.
The feature can be enabled through the following config
CONFIG_EFI_RNG_PROTOCOL
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Changed SPDX header to use /* instead of //.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Since the coprocessor state is tracked in a backup register, there is
no more need for tracking it in an environment variable : remove it.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Khadas VIM3L uses the same board layout as VIM3, but with an S905D3 chip
instead of A311D. Board config is derived from khadas-vim3_defconfig and
sei610_defconfig. README is based on README.khadas-vim3; the difference
is that VIM3L uses FIP files from the g12a folder in vendor sources not
the g12b folder.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added vim3l readme into w400 MAINTAINERS]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeFDfVAAoJEB6zHgIOrC/IKfsH/2cUfXuc9IgA7L90L3g7htlS
zLAQSC8Xk0WbgbmBJh/lq6zFWj2Mu2yfkZqRzwN8bHkmOPq40F+pEAszVtjH77HM
FpSjMSDVWfNXuhmoiS571dehA0TGi1b2kknrAXqpOwVuMRncMCwaPi8yZYZSGlSV
VzMtguQxD0sZg4oMZVde3tCd41smPTPNDjzLZnXdLa0b09+EtW6enGuk3vzXlS/8
QUT68wUzkeoptJhf3pQ3BXNvkFwdNdYJ74uevDmkAYtvxyl10WNykcwYmH50Q9qq
9plF11EizmTHlj16rWpZLx66RP0s4pziKaeGMr6S8uln33Cr9N496wPqtuDBnvA=
=FYPj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.04 cycle
This feature set is a patch series from Tudor Ambarus which includes
parsing of the spi flash SFDP parser for SST flashes, and using those
tables to retrieve unique saved per device MAC address. This is then
used as base mac address on the SAMA5D2 Wireless SOM EK board.
Add socdk board support for Intel Agilex SoC
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
According to the SOM and reference board the clock
can be taken from the external pin or provided from
ENET_REF_CLK. Add a new function that make the proper
set according the board type.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Make easy to map fdt file to board in order to use
this information later to apply specific change to
specific board combination.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
