Commit Graph

7181 Commits

Author SHA1 Message Date
Vipin KUMAR
7f0730a02e mtd/NAND: Add FSMC driver support
Flexible static memory controller is a peripheral provided by ST,
which controls the access to NAND chips along with many other
memory device chips eg NOR, SRAM.

This patch adds the driver support for FSMC controller interfacing
with NAND memory.

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
2012-07-07 14:07:38 +02:00
Holger Brunck
c471d84808 arm/km: remove calls to kw_gpio_* in board_early_init_f
These functions tried to access two static tables before relocation
(board_early_init_f is executed before relocation). But these static
tables lie in the bss section which is not valid before relocation.
These accesses then overwrote some parts of u-boot binary before it was
relocated. For the kmnusa build, this results in a corrupted important
env variable (bootcmd) but it may be that some other parts of the u-boot
binary are corrupted.

This patch solves this problem by moving all the kw_gpio_* calls to
board_init, which should be early enough in the boot sequence. The only
calls that could not be moved is the one for the SOFT (bitbang) I2C, and
they have been replaced by a direct access to the GPIO dataout Control
register to set the two GPIOs as output.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:38 +02:00
Thomas Herzmann
b8cf7cc886 arm/km: add implementation for read_dip_switch
Add a function to read the dip_switch on kmcoge5un. If the
switch is set the actual_bank is set to 0 and this SW is
booted.

Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2012-07-07 14:07:37 +02:00
Holger Brunck
48ced62cfb arm/km: cleanup km_kirkwood boards
Remove config options from boards.cfg and simply add one switch
per board and differ afterwards in km_kirkwood.h between the features.
More boards are upcoming and therefore it's easier to have this
at one place.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:37 +02:00
Valentin Longchamp
b37f772433 arm/km: enable BOCO2 FPGA download support
This adds a first support of the FPGA download for a PCIe FPGA based
on the BOCO2 CPLD.

This takes place in 3 steps, all done accessing the SPICTRL reg of the
BOCO2:
1) start the FPGA config with an access to the FPGA_PROG bit
2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to 1
   for the end of the FPGA configuration (with a timeout)
3) reset the FPGA
4) finally remove the access to its config EEPROM from the FPGA so that
   the CPU can update the FPGA configuration when the kernel is running

The boards with a PCIe FPGA but without BOCO2 still are supported.

The config option name is CONFIG_KM_FPGA_CONFIG

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:37 +02:00
Holger Brunck
6ef6486180 arm/km: remove portl2.h and use km_kirkwood instead
The additional headerfile is unneeded here, we can use the generic
km_kirkwood.h instead. And we can use the better config option
KM_PIGGY4_88E6061 for the specific features for boards with this
design in km_arm.c.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:37 +02:00
Holger Brunck
f945439af9 arm/km: convert mgcoge3un target to km_kirkwood
Use the generic header km_kirkwood.h and get rid of the
board specific header.

changes for v2: rebased because of changes in other patches

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:37 +02:00
Holger Brunck
d9354530fe arm/km: add kmcoge5un board support
For u-boot this board is similar to mgcoge3un. But some differences
are present. We have a different SDRAM on it and therefore a new
SDRAM config file. Additionaly this board has a direct MAC/MAC
connection from the kirkwood to a marvell simple switch without a
phy inbetween, this needs a new configuration for the mvgbe driver.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:36 +02:00
Holger Brunck
8170aefc84 arm/km: add kmnusa board support
This board is similar to portl2, but it has the u-boot environment
in a SPI NOR flash and not in an i2c eeprom like portl2 have.

Some other details:
 - IVM EEPROM is at adress: pca9547:70:9
 - PCI is enabled
 - PIGGY4 is connected via MV88E6352 simple switch. There is no phy
   between the simple switch and the kirkwood.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:36 +02:00
Nikita Kiryanov
816e392148 cm-t35: fix incorrect NAND_ECC layout selection
The current configuration selects an incorrect NAND ECC layout,
which causes u-boot to write HW ECC data incorrectly.
This patch selects the right layout.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2012-07-07 14:07:36 +02:00
SRICHARAN R
f3f98bb0b8 ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.
Currently on OMAP4/5 platforms, many kernel drivers are dependent
upon the bootloaders for mux, dpll and clock configurations.
This should not be the case and bootloaders should set only the
minimum required for the uboot functionality and kernel boot.

Note that this is going to break the kernel drivers. But this
is the only way to get things fixed in the kernel.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07 14:07:36 +02:00
Marek Vasut
0ec005fe00 Kirkwood: Add support for Ka-Ro TK71
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Wolfgang Denk <wd@denx.de>
2012-07-07 14:07:33 +02:00
Valentin Longchamp
0c25defccd arm/km: use spi claim bus to switch between SPI and NAND
We overwrite these weak functions from the kirkwood spi code to
use our own method to be able to switch between the SPI NOR and
the NAND flash. This is needed e.g. to update the u-boot. The former
command do_spi_toggle can therefore be removed. And the usage of
this command is removed from the u-boot update command in the
u-boot environment.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:33 +02:00
Simon Guinot
d92151b925 lacie_kw: fix CONFIG_SYS_KWD_CONFIG for inetspace_v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2012-07-07 14:07:32 +02:00
Simon Guinot
c4c4b0e661 lacie_kw: fix SDRAM banks number for net2big_v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2012-07-07 14:07:32 +02:00
Michael Walle
f214a20e7e Kirkwood: add lschlv2 and lsxhl board support
This patch adds support for both the Linkstation Live (LS-CHLv2) and
Linkstation Pro (LS-XHL) by Buffalo.

Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:32 +02:00
Michael Walle
03c1b04f86 net: add helper to generate random mac address
Add new function eth_random_enetaddr() to generate a locally administered
ethernet address.

Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
2012-07-07 14:07:32 +02:00
Michael Walle
99e139d590 net: use common rand()/srand() functions
Replace rand() with the functions from lib/. The link-local network code
stores its own seed, derived from the MAC address. Thus making it
independent from calls to srand() in other modules.

Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2012-07-07 14:07:32 +02:00
Michael Walle
9acf1ca50d lib: add rand() function
It's a PRNG using the simple and fast xorshift method.

Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Wolfgang Denk <wd@denx.de>
2012-07-07 14:07:32 +02:00
Valentin Longchamp
a0fb94f9ed km_arm: use filesize for erase in update command
We used to have an arbitrary value, which can be a problem if we have a
u-boot image that is bigger than this value.

This patch is dependant on the whole km/arm series and will be included
in the v3 of the series if there is one.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:31 +02:00
Valentin Longchamp
002ec08d6d arm/km: enable mii cmd
This is useful to debug the switch initialization

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:31 +02:00
Holger Brunck
be67190e48 arm/km: remove CONFIG_RESET_PHY_R
This is already defined in the generic kirkwood header.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:31 +02:00
Holger Brunck
af85f08588 arm/km: rename CONFIG option CONFIG_KM_DEF_ENV_UPDATE
This config option sounds like the it is responsible for the
update of  the environment, but it is the u-boot update handling.
Therefore we adapt it to a more apropriate naming.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:30 +02:00
Holger Brunck
f5b5a1c80e arm/km: add piggy mac adress offset for mgcoge3un
On mgcoge3un the piggy mac adress is at offset 3.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:30 +02:00
Holger Brunck
e29c6d0401 arm/km: add board type to boards.cfg
Some other kirkwood boards from keymile will follow. They will have some
small differences, but we want to use the km_kirkwood.h for all to
distinguish them. This patch a preparation for this.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:30 +02:00
Alexandre Belloni
e139cb31d3 AT91SAM9*: Change kernel address in dataflash to match u-boot's size
On at91sam platforms, u-boot grew larger than the allocated size in
dataflash, the layout was:
bootstrap  0x00000000
ubootenv   0x00004200
uboot      0x00008400
kernel     0x00042000
fs         0x00252000

u-boot with the defconfig doesn't seem to fit in 0x42000 - 0x8400 =
0x39C00 bytes anymore.

Now, the layout is:
bootstrap  0x00000000
ubootenv   0x00004200
uboot      0x00008400
kernel     0x00084000
fs         0x00294000

Signed-off-by: Alexandre Belloni <alexandre.belloni@piout.net>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-07-07 14:07:30 +02:00
Bo Shen
e1edd06594 AT91: at91sam9m10g45ek : Enable EHCI instead OHCI
Enable EHCI support instead OHCI

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-07-07 14:07:29 +02:00
esw@bus-elektronik.de
5e7d0917b6 Fix: AT91SAM9263 nor flash usage
Fix: board doesn't boot from norflash
 Fix: environment can't write to flash (end address/start address not on sector boundary)

Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-07-07 14:07:29 +02:00
Fabio Estevam
7d77891605 mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07 14:07:28 +02:00
Fabio Estevam
fd8223eaa9 mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07 14:07:28 +02:00
Fabio Estevam
6ce85ad5c7 mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07 14:07:28 +02:00
Fabio Estevam
b6a5fbf4bf mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07 14:07:28 +02:00
Fabio Estevam
bd6f402b2a mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07 14:07:28 +02:00
Fabio Estevam
29ee7f5487 imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition
According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07 14:07:28 +02:00
Fabio Estevam
3e5a0f35f1 mx53ard: Remove unused CONFIG_MII_GASKET
CONFIG_MII_GASKET is not defined anywhere, so remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07 14:07:28 +02:00
Otavio Salvador
be8d6b614f m28evk: use same notation to alloc the 128kB stack
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Wolfgang Denk <wd@denx.de>
2012-07-07 14:07:27 +02:00
Otavio Salvador
a2277e8403 m28evk: drop duplicated definition of CONFIG_OF_LIBFDT
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
2012-07-07 14:07:27 +02:00
Otavio Salvador
606de8b6a6 mx28evk: fix board config include guardian macro name
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07 14:07:27 +02:00
Otavio Salvador
3b4efee97c mx28evk: ensure command definition is in alphabetic order
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07 14:07:27 +02:00
Otavio Salvador
212033fc9a m28evk: fix board config include guardian macro name
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
2012-07-07 14:07:27 +02:00
Fabio Estevam
eae08eb2b5 mx53loco: Fix revision of Dialog boards
Original code was assuming that the fuse revision version for all mx53loco boards
based on Dialog PMIC was the same, which is not the case.

Force the revision of all Dialog-based boards to 0.

This fixes a kernel crash when PMIC is accessed in the 2.6.35 kernel
for Dialog rev E boards.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07 14:07:25 +02:00
Igor Grinberg
390cdcda1b cm-t35: reduce the environment size
Reduce the environment size (128KB => 16KB) to improve the environment
operations time (e.g. reading, ecc calculation).
Also, remove the unused CONFIG_SYS_ENV_SECT_SIZE.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-07-07 14:07:24 +02:00
Tom Rini
1ee6d31ff4 omap3evm: Add CONFIG_CMD_ASKENV
Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07 14:07:23 +02:00
Tom Rini
776bebb758 omap3_beagle: Add CONFIG_CMD_ASKENV
Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07 14:07:23 +02:00
Tom Rini
2e4b8b5cd2 omap3evm: Set BOOTDELAY to 3
We reduce the bootdelay from 10s to 3s to give users a short but usable
window to interrupt the boot process if needed.

Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07 14:07:23 +02:00
Tom Rini
1dd07fe8e9 OMAP3 Beagle: Set BOOTDELAY to 3
We change the bootdelay to give users a little bit longer to break in if
needed.

Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07 14:07:23 +02:00
Heiko Schocher
14b9f16c40 arm,davinci: update for enbw_cmc board
- change gpio pin settings:

  - gpio pin 6[13] (PLC reset) default value low
  - gpio pin 6[0] (TPM reset) default value low
  - 4 new GPIO pins
      pin  i/o   name
    - 3[9] input Board Type
    - 2[7] input HW-ID0
    - 2[6] input HW-ID1
    - 2[3] input HW-ID2

- read board type and hw id from gpio pins on the enbw_cmc board,
  and use board type for setting up different gpio pin settings.

- do not pass "davinci_mmc.use_dma=0" to linux, as MMC now
  works with DMA.

- update logbuf support:
  store post word in RTC scratch register

- add support for configuring KSZ8864RMN switch through
  a config file on u-boot startup. For more infos see:
  doc/README.switch_config

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
2012-07-07 14:07:21 +02:00
Thomas Weber
d1df0fd373 omap4/5: Use CPUDIR for .lds script
Signed-off-by: Thomas Weber <thomas@tomweber.eu>
2012-07-07 14:07:21 +02:00
Stephen Warren
1e7e716e80 tegra: trimslice: fix a couple typos
Fix the .dts file USB unit addresses not to duplicate each-other.

Fix the board name string to indicate the vendor is Compulab not NVIDIA.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-07-07 14:07:21 +02:00
Tom Warren
76e350b7a3 arm: Tegra: Use ODMDATA from BCT in IRAM
Walk the BIT and BCT to find the ODMDATA word in the
CustomerData field and put it into Scratch20 reg for
use by kernel, etc.

Built all Tegra builds OK; Booted on Seaboard and saw
ODMDATA in PMC scratch20 was the same as the value in my
burn-u-boot.sh file (0x300D8011). NOTE: All flash utilities
will have to specify the odmdata (nvflash --odmdata n) on
the command line or via a cfg file, or built in to their
BCT.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
2012-07-07 14:07:21 +02:00
Stephen Warren
f9f2f12e2c tegra: seaboard: disable SPI, move environment to eMMC
The SPI hardware on Seaboard is too broken to use; it is muxed with the
console UART and requires evil interactions between the SPI and UART
drivers to work even partially. The current code in U-Boot is not
sufficient to make this work correctly; auto boot is aborted due to
corruption in the UART RX channel interrupting it.

Instead, move the environment to eMMC, at the end of the second boot
sector. This should not conflict with any other eMMC usage, irrespective
of whether the board boots from SPI, NAND, or eMMC: if U-Boot is stored
in eMMC, it will be stored well below this location. The kernel only
uses the general area of the eMMC once booted, not the boot sectors.

Boards that are derivatives of Seaboard don't have the muxing issue,
and should/could have a separate U-Boot configuration file that does
enable SPI if desired.

Alternatively, the environment could be stored in NAND flash, but we
currently have no driver for that controller.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:21 +02:00
Stephen Warren
e87c2bda9c tegra: paz00: store environment in eMMC
Store the environment in eMMC, at the end of the second boot sector.
This should not conflict with any other eMMC usage: U-Boot is stored
well below this location, and the kernel only uses the general area
of the eMMC once booted, not the boot sectors.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:21 +02:00
Stephen Warren
a5c168c6d6 tegra: trimslice: store environment in SPI flash
The chosen flash offset matches Compulab's downstream U-Boot.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:20 +02:00
Tom Warren
52a8b82074 gpio: tegra2: rename tegra2_gpio.* to tegra_gpio.*
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:20 +02:00
Tom Warren
3f82d89d3d mmc: tegra2: rename tegra2_mmc.* to tegra_mmc.*
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:20 +02:00
Tom Warren
edffa63d3d spi: tegra2: rename tegra2_spi.* to tegra_spi.*
In anticipation of Tegra3 support, start removing/renaming
Tegra2-specific files. No functional changes (yet).
Also updated copyright to 2012.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:20 +02:00
Stephen Warren
616887016d tegra: whistler: store environment in eMMC
Store the environment in eMMC, at the end of the second boot sector.
This should not conflict with any other eMMC usage: U-Boot is stored
well below this location, and the kernel only uses the general area
of the eMMC once booted, not the boot sectors.

Note: This assumes the user plugged the standard 8MB MoviNAND card into
J29/HSMMC/POP. If they didn't, the boot sector layout may be different.
However, use of that particular card is standard practice as far as I
know.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:20 +02:00
Stephen Warren
294cd67c8d tegra: ventana: store environment in eMMC
Store the environment in eMMC, at the end of the second boot sector.
This should not conflict with any other eMMC usage: U-Boot is stored
well below this location, and the kernel only uses the general area
of the eMMC once booted, not the boot sectors.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:20 +02:00
Stephen Warren
b1b9e4ce3a tegra: ventana: add own device tree, enable USB
Add a device tree for Ventana; the Seaboard file no longer represents
the HW present on Ventana.

Enable USB on Ventana.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:19 +02:00
Stephen Warren
59f8ac65f8 tegra: remove CONFIG_USB_ETHER_SMSC95XX from boards without it
The SMSC95xx series may exist either directly on a main board, or as a USB
to Ethernet dongle. However, dongles containing these chips are very rare.
Hence, remove this config option, except on Harmony where such a chip is
actually present on the board.

The asix option remains, since it's a popular chip, and I actively use a
dongle containing this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-07-07 14:07:19 +02:00
Stephen Warren
00a55add04 tegra: paz00: add device tree support
... to enable USB host support, which enables Ethernet support.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:19 +02:00
Stephen Warren
f3d93309c1 tegra: harmony: add device tree support
... to enable USB host support, which enables Ethernet support.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:19 +02:00
Stephen Warren
39e3711839 tegra: Compulab TrimSlice board support
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:19 +02:00
Stephen Warren
defd5e4979 tegra: seaboard: add support for USB networking
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:18 +02:00
Stephen Warren
dae2aeab71 tegra: whistler: reduce and comment network cfg options
CONFIG_CMD_PING/NFS aren't required for Whistler to boot.

Add some comments.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:18 +02:00
Stephen Warren
bea2674ccd tegra: flesh out bootcmd
This implements a useful bootcmd for Tegra. The boot order is:

* If USB enabled, USB storage
* Internal MMC (SD card or eMMC)
* If networking is enabled, BOOTP/TFTP

When booting from USB or MMC, the boot script is assumed to be in
partition 1 (although this may be overridden via the rootpart variable),
both ext2 and FAT filesystems are supported, the boot script may exist
in either / or /boot, and the boot script may be named boot.scr.uimg or
boot.scr.

When booting over the network, it is assumed that boot.scr.uimg exists
on the TFTP server. There is less flexibility here since those setting
up network booting are expected to need less hand-holding.

In all cases, it is expected that the initial file loaded is a U-Boot
image containing a script that will load the kernel, load any required
initrd, load any required DTB, and finally bootm the kernel.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:18 +02:00
Stephen Warren
07a84b7b19 tegra: remove some cruft from CONFIG_EXTRA_ENV_SETTINGS
console isn't used by anything, and the kernel should be set appropriately
by whatever script is booting the kernel, not imposed by the bootloader.

mem might be useful, but the current value is pretty bogus, since it
includes nvmem options that make no sense for an upstream kernel, and
equally should not be required for any downstream kernel. Either way, this
is also best left to the kernel boot script.

smpflag isn't used by anything, and again was probably intended to be a
kernel command-line option better set by the kernel boot script.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:17 +02:00
Stephen Warren
d5ebc937c9 tegra: Whistler board support
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:

E1120 motherboard
E1108 CPU board
E1116 PMU board

The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.

Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:17 +02:00
Tom Warren
046c76a6c0 spi: Tegra2: Seaboard: enable SPI/UART corruption fix
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:17 +02:00
Timur Tabi
7b6e80538b lib/powerpc: addrmap_phys_to_virt() should return a pointer
addrmap_phys_to_virt() converts a physical address (phys_addr_t) to a
virtual address, so it should return a pointer instead of an unsigned long.
Its counterpart, addrmap_virt_to_phys(), takes a pointer, so now they're
orthogonal.

The only caller of addrmap_phys_to_virt() converts the return value to
a pointer anyway.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-07-06 17:30:32 -05:00
Timur Tabi
84e34b6572 powerpc/85xx: clean up P1022DS board configuration header file
Remove some unused default environment variables (memctl_intlv_ctl,
perf_mode, diuregs, dium, and diuerr), update 'tftpflash' variable,
and add videobootargs as a Linux command line variable (so that we can
easily pass video= to the kernel).

Signed-off-by: Timur Tabi <timur@freescale.com>
2012-07-06 17:30:32 -05:00
Timur Tabi
fb365a8a96 powerpc/85xx: minor clean-ups to the P2020DS board header file
Remove some unused macros and remove all #undef macros.

The RTL8139 network adapter is not shipped with the board nor commonly
used, so don't define it by default.  The E1000 is still defined.

Add 57,600 baud as an option.  For some reason, this baud rate is missing
from many boards.

Signed-off-by: Timur Tabi <timur@freescale.com>
2012-07-06 17:30:32 -05:00
Prabhakar Kushwaha
7530d341c7 powerpc/mpc85xx:Add BSC9131 RDB Support
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. BSC9131 SOC
 is an integrated device that targets Femto base station market. It combines
 Power Architecture e500v2 and DSP StarCore SC3850 core technologies with
 MAPLE-B2F baseband acceleration processing elements

  BSC9131RDB Overview
   -----------------
     -1Gbyte DDR3 (on board DDR)
     -128Mbyte 2K page size NAND Flash
     -256 Kbit M24256 I2C EEPROM
     -128 Mbit SPI Flash memory
     -USB-ULPI
     -eTSEC1: Connected to RGMII PHY
     -eTSEC2: Connected to RGMII PHY
     -DUART interface: supports one UARTs up to 115200 bps for console display
Apart from the above it also consists various peripherals to support DSP
functionalities.

This patch adds support for mainly Power side functionalities and peripherals

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-07-06 17:30:29 -05:00
ramneek mehresh
3d7506fa38 powerpc/85xx: Add USB device-tree fixup for various platforms
Add USB device-tree fixup for following platforms:
MPC8536DS, P1022DS, P1023RDS, P2020COME, P2020DS, P2041RDB, P3060QDS

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
2012-07-06 17:03:25 -05:00
Kim Phillips
c8a90646ad powerpc/mpc83xx: increment malloc heap size
extention of commit 3b6b256 "powerpc/mpc83xx: increment
malloc heap size for the MPC832x MDS boards" to all other
mpc83xx based boards.  It fixes "Unable to save the rest
of sector" messages when trying to save the environment
to flash.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-07-03 11:07:21 -05:00
Stephan Linz
7cfb13a7f4 microblaze: Enable ubi support
Increase malloc area for UBI to >= 512k -- foreseeing of UBIFS
set to 768k. To save memory in flash (CONFIG_SYS_MONITOR_LEN)
the UBIFS is disabled by default.

Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-06-27 10:18:44 +02:00
Stephan Linz
1fe7e8fa48 microblaze: Avoid compile error on systems without cfi flash
Use XILINX_FLASH_START to set/unset FLASH and RAMENV.

Error:
board.c: In function 'board_init':
board.c:134: error: 'XILINX_FLASH_START' undeclared (first use in this function)
board.c:134: error: (Each undeclared identifier is reported only once
board.c:134: error: for each function it appears in.)

Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-06-27 10:18:20 +02:00
Stephan Linz
2629d63efc microblaze: Remove wrong define CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_PROTECTION is defined twice. The second one
is outside the flash configuration context and we can remove
it safely.

Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-06-27 10:17:46 +02:00
Rob Herring
669df7e42d pxe: add support for parsing local syslinux files
Add a new command "sysboot" which parses syslinux menu files and boots
using kernel and initrd specified by menu files. The operation is similar
to "pxe boot" except local files on ext2 or fat filesystem are parsed.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-06-21 22:35:56 +02:00
Marek Vasut
b37d41aa24 Block: Remove MG DISK support
This driver is unused and obsolete.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: unsik Kim <donari75@gmail.com>
2012-06-21 20:53:09 +02:00
Tom Rini
219f4788d3 hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2.  I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-06-20 20:36:51 +02:00
Tom Rini
26750c8aee CONFIG_SYS_BAUDRATE_TABLE: Add <config_fallbacks.h>, place there
We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file.  This is used when a board has not set its
own table.

Signed-off-by: Tom Rini <trini@ti.com>
2012-06-20 20:26:16 +02:00
Mike Frysinger
9595260e0b lmb: do not export anything without CONFIG_LMB
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-06-19 22:35:10 +02:00
Thomas Herzmann
c1b3d84168 km/common: check test_bank and testpin for testboot
If the testpin is asserted, first check if a test_bank
variable is defined before trying to boot this
test_bank.

Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15 17:12:52 -05:00
Thomas Herzmann
95209b6684 powerpc/83xx: configure CONFIG_POST for kmcoge5ne
kmcoge5ne starts the post tests if the testpin on
the board was enabled. Currently it does simply a memory
test.

Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15 17:12:51 -05:00
Holger Brunck
31dd8988e2 km/common: increase bootlimit to 3
Increase bootlimit to 3 to be more tolerant during the
boot process before switching to the backup application.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15 17:12:40 -05:00
Holger Brunck
0f2b721c80 powerpc/83xx: add kmcoge5ne board support
This board is a MPC8360 board. Two flashes are present
a NOR flash were u-boot and the u-boot environment is stored
and a NAND flash for the application code. This board has 512MB
SDRAM.

Additionaly we introduce a common km8360.h file and convert kmeter1 to
use this.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Christian Herzig <christian.herzig@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15 17:12:40 -05:00
Andreas Huber
cf73639d32 km/common: add support for second flash
Add support for a second flash.
By default, a single flash chip is set up:
- called 'boot'
- mtd name for ubi 'ubi0'
MTDIDS and MTDPARTS may be overwritten to add a second flash.
The 'ubiattach' command is featured in two versions:
- if CONFIG_KM_UBI_PARTITION_NAME_APP is not defined:
  this is the version as up to now
- if CONFIG_KM_UBI_PARTITION_NAME_APP is defined:
  a check on 'actual_bank' will be done to determine the flash to boot
  from.

Use CONFIG_KM_UBI_PARTITION_NAME_BOOT and
CONFIG_KM_UBI_PARTITION_NAME_APP to define where to put the bootloader
and the applications.

Example:
In the board config do:
... snip ...

       "boot:"                                                 \
               "768k(u-boot),"                                 \
               "128k(env),"                                    \
               "128k(envred),"                                 \
               "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");"     \
       "app:"                                                  \
               "-(" CONFIG_KM_UBI_PARTITION_NAME_APP ");"

... snap ...

You may also need to enable the second flash:
... snip ...
/* additional featured for COGE5 */
... snap ...

Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15 17:07:11 -05:00
Holger Brunck
7ba1c870da powerpc83xx/km: remove unneeded CONFIG_PCI for kmeter1
We don't use PCI on kmeter1 and never will be, so remove some
unneeded code.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15 16:42:32 -05:00
Holger Brunck
7f4bd9a686 powerpc/83xx/km: use tuxx1.h for kmsupx5 target
This additional header is unneeded, we can use the tuxx1.h for this
target.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15 16:42:32 -05:00
Timur Tabi
3b6b256c43 powerpc/83xx: increment malloc heap size for the MPC832x MDS boards
The malloc buffer is not large enough to hold a flash sector (0x20000 bytes)
in addition to whatever else it normally holds, so double its size.  This
fixes a failure trying to save the environment:

=> save
Saving Environment to Flash...
Unable to save the rest of sector (122880)
. done
Protected 1 sectors

This problem probably surfaced from some other change that significantly
increased the normal memory usage, thereby not leaving enough room for
the saveenv command.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15 16:42:32 -05:00
Wolfgang Denk
fedab338f3 Merge branch 'master' of git://git.denx.de/u-boot-video
* 'master' of git://git.denx.de/u-boot-video:
  video: atmel/lcd: add LCD driver for new Atmel SoC
  video: cfb_console: flush dcache for frame buffer in DRAM
  cfb_console: Ignore bell character
  cfb_console: Add console_clear_line function
  cfb_console: Fix function console_back
  omap3_dss: cosmetic changes
  omap3_dss: add optional framebuffer
  mx53loco: Add LCD support
  mx5: Rename mx51_fb_init()
  mx53: Allow IPUv3 driver to also work on mx53
  mx51evk: Add LCD support
  EXYNOS: display 32bpp bitmap TIZEN logo
  create lib/tizen directory
  LCD: display 32bpp decompressed bitmap image
  common/lcd.c: reduce one CONFIG_LCD_LOGO ifdef
  common/lcd.c: reduce some CONFIG_LCD_*_LOGO ifdefs
  common/lcd.c: use ARRAY_SIZE
  cmd_bmp.c: make bmp_display() usable by drivers or board code
  LCD: support another s6e8ax0 panel type
  LCD: change s6e8ax0 panel gamma value
  include/video.h: drop unused video_printf()

Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-06-07 23:42:17 +02:00
Wolfgang Denk
d1c6e9e44a Merge branch 'master' of git://git.denx.de/u-boot-mips
* 'master' of git://git.denx.de/u-boot-mips:
  MIPS: board.c: move extern declarations to u-boot-mips.h
  MIPS: bootm_qemu_mips.c: make checkpatch.pl clean
  MIPS: bootm.c: make checkpatch.pl clean

Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-06-07 23:38:54 +02:00
Bo Shen
f6b690e65c video: atmel/lcd: add LCD driver for new Atmel SoC
The new Atmel SoC (at91sam9x5 series and at91sam9n12) add a totally
different LCD controller. Add this new driver to support it.

Using CONFIG_ATMEL_HLCD (distinguish with CONFIG_ATMEL_LCD) to enable
this in board configuration file.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-06-05 11:19:02 +02:00
Daniel Schwierzeck
e034ea3b77 MIPS: board.c: move extern declarations to u-boot-mips.h
This fixes some remaining checkpatch.pl warnings.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2012-06-03 23:46:04 +02:00
Phil Edworthy
99744b7e34 sh: Add SH7269 device and RSK2+SH7269 board
This is an sh2a device (max 266MHz) with FPU, video display
controller (VDC), 8 serial ports, 4 I2C channels, 3 CAN ports,
SD and on-chip USB.

The RSK2+SH7269 board uses the SH7269 processor. It is often
referred to as just rsk7269.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-05-28 09:12:54 +09:00
Nobuhiro Iwamatsu
a80a661989 sh: Set CONFIG_SH_ETHER_PHY_MODE and CONFIG_SH_ETHER_SH7734_MII to boards with sh_eth
The board with sh_eth needs to set CONFIG_SH_ETHER_PHY_MODE.
And SH7734 needs to set value of CONFIG_SH_ETHER_SH7734_MII.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-05-28 09:12:54 +09:00
Nobuhiro Iwamatsu
bfc93fb47d sh: Add support for AP-SH4A-4A board
The AP-SH4A-4A board has SH7734, 64MB DDR2-SDRAM, USB,
Ethernet, and more.

This patch supports the following functions:
  - 64MB DDR2-SDRAM
  - 16MB NOR Flash memory
  - Serial console (SCIF)
  - Ethernet (SH-Ether with Gigabit)
  - I2C

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-05-28 09:12:54 +09:00
Nobuhiro Iwamatsu
d740555968 sh: r0p7734: Add support I2C controller
This read MAC address from Serial EEPROM and set.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-05-28 09:12:53 +09:00
Nobuhiro Iwamatsu
8ca805e102 sh: Add support for r0p7734 board
The r0p7734 board has SH7734, 128MB DDR2-SDRAM, USB,
Ethernet, and more.

This patch supports the following functions:
- 128MB DDR2-SDRAM
- 32MB NOR Flash memory
- Serial console (SCIF)
- Ethernet (SH-Ether/SMSC)

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-05-28 09:12:53 +09:00
Fabio Estevam
f714b0a911 mx53loco: Add LCD support
Add support for CLAA07LC0ACW LCD that connects to the mx53loco board.

Configure the board to show the Linux logo on the LCD.

Also increase the size of CONFIG_SYS_MALLOC_LEN variable to take into account
the framebuffer usage.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
2012-05-25 10:40:32 +02:00
Fabio Estevam
a1b0e190a3 mx5: Rename mx51_fb_init()
The ipuv3 driver is currently only used on mx51, but it can be extended to work
on mx53 and mx6 as well.

Rename mx51_fb_init(), so that it can be used by other SoCs.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
2012-05-25 10:39:23 +02:00
Fabio Estevam
f1adefd239 mx51evk: Add LCD support
Add support for CLAA07LC0ACW LCD that connects to the mx51evk board.

Configure the board to show the Linux logo on the LCD.

Also increase the size of CONFIG_SYS_MALLOC_LEN variable to take into account
the framebuffer usage.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-25 10:06:38 +02:00
Donghwa Lee
90464971f9 EXYNOS: display 32bpp bitmap TIZEN logo
This patch supports drawing 32bpp bitmap TIZEN logo in exynos fb.
"tizen_hd_logo.h" data is compressed from trats_logo.bmp to
trats_logo.bmp.gz by gzip and converted to tizen_hd_logo.h header file
format by some application. The logo data is decompressed in the exynos
fb driver by bmp_display().

Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-05-25 09:15:10 +02:00
Donghwa Lee
5a4c59be89 create lib/tizen directory
This directory includes tizen logo data, common tizen library and so on.

Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>

[ agust: change to conditionally build lib/tizen directory ]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-05-25 09:15:10 +02:00
Anatolij Gustschin
de3b49c4dd cmd_bmp.c: make bmp_display() usable by drivers or board code
Currently bmp_display() is static and can not be used directly
in the driver or board code. Export it for other users.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-05-25 09:15:09 +02:00
Anatolij Gustschin
ed82fb145a include/video.h: drop unused video_printf()
There is no such function in the code, so remove this prorotype.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-05-25 09:15:09 +02:00
Joe Hershberger
4ef8d53caa net: Allow filtering on debug traces in the net subsystem
Add several levels of DEBUG prints so that you can limit the noise to
the severety of your problem.

DEBUG_LL_STATE = Link local state machine changes
DEBUG_DEV_PKT = Packets or info directed to the device
DEBUG_NET_PKT = Packets on info on the network at large
DEBUG_INT_STATE = Internal network state changes

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-23 17:53:08 -05:00
Joe Hershberger
d22c338e07 net: Add link-local addressing support
Code based on networking/zcip.c in busybox
commit 8531d76a15890c2c535908ce888b2e2aed35b172

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-23 17:53:08 -05:00
Joe Hershberger
e94070c443 net: Don't copy every packet that waits for an ARP
Use the NetArpTxPacket for the ARP packet, not to hold what used to
be in NetTxPacket.
This saves a copy and makes the code easier to understand.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-05-23 17:53:07 -05:00
Joe Hershberger
46c495d524 net: Fix net buffer initialization
A new non-static function net_init() will initialize buffers and
read from the environment.  Only update from the env on each entry
to NetLoop().

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-05-23 17:53:06 -05:00
Joe Hershberger
e711101581 net: Add net_update_ether() to handle ARP and Ping replies
When the network is VLAN or SNAP, net_update_ether() will preserve
the original Ethernet packet header and simply replace the src and
dest MACs and the protocol

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-05-23 17:53:04 -05:00
Joe Hershberger
ece223b52a net: Refactor to separate the UDP handler from the ARP handler
Call a built-in dummy if none is registered... don't require
protocols to register a handler (eliminating dummies)
NetConsole now uses the ARP handler when waiting on arp
(instead of needing a #define hack in arp.c)
Clear handlers at the end of net loop

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-05-23 17:52:53 -05:00
Joe Hershberger
22f6e99d5b net: Refactor to protect access to the NetState variable
Changes to NetState now go through an accessor function called
net_set_state()

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-23 17:46:21 -05:00
Joe Hershberger
adf5d93e44 net: Refactor to use NetSendPacket instead of eth_send directly
Use this entry-point consistently across the net/ code
Use a static inline function to preserve code size

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-05-23 17:46:20 -05:00
Joe Hershberger
4b11c9166b net: Refactor IP, UPD, and ICMP header writing functions
ICMP (ping) was reimplementing IP header code... it now shares code.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-05-23 17:46:18 -05:00
Joe Hershberger
674bb24982 net: cosmetic: Replace magic numbers in arp.c with constants
Use field names and sizes when accessing ARP packets

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-23 17:46:18 -05:00
Joe Hershberger
da5ebe2c9a net: cosmetic: Add a more explicit comment about 802.2
Make the comment more accurate about the header including SNAP

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-05-23 17:46:16 -05:00
Joe Hershberger
206d07fd7c net: cosmetic: Rename parameter len to payload_len
This name more explicitly claims that it does not include the
header size

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-05-23 17:46:15 -05:00
Joe Hershberger
e0a630795b net: cosmetic: Un-typedef ICMP_t
Remove typedef and lower-case name

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-23 17:46:15 -05:00
Joe Hershberger
738853bb6d net: cosmetic: Un-typedef ARP_t
Remove typedef and lower-case letters

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-23 17:46:15 -05:00
Joe Hershberger
c68cca35b3 net: cosmetic: Un-typedef VLAN_Ethernet_t
Eliminate the typedef and remove capital letters

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-23 17:46:14 -05:00
Joe Hershberger
cb487f5664 net: cosmetic: Un-typedef Ethernet_t
Separate the Ethernet header from the 802 header.
Base the size constants on the structs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-23 17:46:14 -05:00
Joe Hershberger
c5c59df04d net: cosmetic: Split struct ip_udp_hdr into ip_hdr
Add a structure that only contains IP header fields to be used by
functions that don't need UDP
Rename IP_HDR_SIZE_NO_UDP to IP_HDR_SIZE

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-23 17:46:14 -05:00
Joe Hershberger
594c26f8a7 net: cosmetic: Un-typedef IP_t
Rename IP header related things to IP_UDP. The existing definition
of IP_t includes UDP header, so name it to accurately describe the
structure.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-23 17:46:00 -05:00
Joe Hershberger
d280d3f430 net: Move ARP out of net.c
Separate this functionality out of the net.c behemoth

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-05-23 14:19:23 -05:00
Joe Hershberger
1735188329 net: Encapsulate CDP packet identification
Checking for CDP packets should be encapsulated, not copied code.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-23 14:19:23 -05:00
Joe Hershberger
f575ae1f7d net: Move CDP out of net.c
Separate this functionality out of the net.c behemoth

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-05-23 14:19:22 -05:00
Joe Hershberger
806150063a net: Remove CMD_PING where there's no CMD_NET
Some boards claim to need ping, but don't support net.
That makes no sense, and causes problems now that ping
is in a separate file.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-05-23 14:19:22 -05:00
Anatolij Gustschin
985889b110 include/part.h: fix indentation of lba
Indent at the same level as other struct members.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-05-22 10:14:34 +02:00
Aaron Williams
1d90c3b457 fat: fix FAT sector offsets overflow on large FAT partitions
This patch fixes several issues where sector offsets can overflow due
to being limited to 16-bits. The cases where an overflow can happen
when accessing large FAT32 partitions are:

 - length of FAT in sectors
 - start sector of root directory
 - the sector of the first cluster

These issues were observed when reading files from a 64GB FAT32
filesystem.

Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com>
Tested-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-05-22 10:14:05 +02:00
Wolfgang Denk
2ab5be7af0 Merge branch 'master' of git://git.denx.de/u-boot-usb
* 'master' of git://git.denx.de/u-boot-usb:
  USB: S5P: Add ehci support
  usb:udc:samsung Add functions for storing private gadget data in UDC driver
  usb:gadget:composite: Support for composite at gadget.h
  usb:gadget:composite USB composite gadget support
  usb:udc:samsung:cleanup Replace DEBUG_* macros with debug_cond() calls
  usb:udc: Remove duplicated USB definitions from include/linux/usb/ch9.h file
  USB: Document the QH and qTD antics in EHCI-HCD
  USB: Drop cache flush bloat in EHCI-HCD
  USB: Drop ehci_alloc/ehci_free in ehci-hcd
  USB: Align buffers at cacheline
  usb: use noinline define
2012-05-20 22:51:41 +02:00
Wolfgang Denk
8bd07c9aaf Merge branch 'master' of git://git.denx.de/u-boot-net
* 'master' of git://git.denx.de/u-boot-net:
  net: move bootfile init into eth_initialize
  net: punt bd->bi_ip_addr
  net: cosmetic: netconsole.c checkpatch compliance
  net: cosmetic: tftp.* checkpatch compliance
  net: cosmetic: sntp.* checkpatch compliance
  net: cosmetic: rarp.* checkpatch compliance
  net: cosmetic: nfs.* checkpatch compliance
  net: cosmetic: net.c checkpatch compliance
  net: cosmetic: eth.c checkpatch compliance
  net: cosmetic: bootp.* checkpatch compliance
  net: cosmetic: net.h checkpatch compliance
  net: Remove volatile from net API
2012-05-20 22:33:44 +02:00
Wolfgang Denk
ee3a55fdf0 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm: (167 commits)
  OMAP4/5: Change omap4_sdp, omap4_panda, omap5_evm maintainer
  ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORT
  ARM: omap3: Set SPL stack size to 8KB, image to 54KB.
  arm, omap3: fix warm reset serial output on OMAP36xx/AM/DM37xx
  OMAP4: Set fdt_high for OMAP4 devices to enable booting with Device Tree
  omap4: do not enable auxiliary cores
  omap4: do not enable fs-usb module
  omap4: panda: disable uart2 pads during boot
  igep00x0: change mpurate from 500 to auto
  igep00x0: enable the use of a plain text file
  tegra2: trivially enable 13 mhz crystal frequency
  tegra: Enable keyboard for Seaboard
  tegra: Switch on console mux and use environment for console
  tegra: Add tegra keyboard driver
  tegra: fdt: Add keyboard definitions for Seaboard
  tegra: fdt: Add keyboard controller definition
  tegra: Add keyboard support to funcmux
  input: Add support for keyboard matrix decoding from an fdt
  input: Add generic keyboard input handler
  input: Add linux/input.h for key code support
  fdt: Add fdtdec functions to read byte array
  tegra: Enable LP0 on Seaboard
  tegra: fdt: Add EMC data for Tegra2 Seaboard
  tegra: i2c: Add function to find DVC bus
  fdt: tegra: Add EMC node to device tree
  tegra: Add EMC settings for Seaboard
  tegra: Turn off power detect in board init
  tegra: Set up warmboot code on Nvidia boards
  tegra: Setup PMC scratch info from ap20 setup
  tegra: Add warmboot implementation
  tegra: Set up PMU for Nvidia boards
  tegra: Add PMU to manage power supplies
  tegra: Add EMC support for optimal memory timings
  tegra: Add header file for APB_MISC register
  tegra: Add tegra_get_chip_type() to detect SKU
  tegra: Add flow, gp_padctl, fuse, sdram headers
  tegra: Add crypto library for warmboot code
  tegra: Add functions to access low-level Osc/PLL details
  tegra: Move ap20.h header into arch location
  Add AES crypto library
  i2c: Add TPS6586X driver
  Add abs() macro to return absolute value
  fdt: Add function to return next compatible subnode
  fdt: Add function to locate an array in the device tree
  i.MX28: Avoid redefining serial_put[cs]()
  i.MX28: Check if WP detection is implemented at all
  i.MX28: Add battery boot components to SPL
  i.MX28: Reorder battery status functions in SPL
  i.MX28: Add LRADC init to i.MX28 SPL
  i.MX28: Add LRADC register definitions
  i.MX28: Shut down the LCD controller before reset
  i.MX28: Add LCDIF register definitions
  i.MX28: Implement boot pads sampling and reporting
  i.MX28: Improve passing of data from SPL to U-Boot
  M28EVK: Add SD update command
  M28EVK: Implement support for new board V2.0
  FEC: Abstract out register setup
  MX5: PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH exchanged
  i.MX28: Add delay after CPU bypass is cleared
  spi: mxs: Allow other chip selects to work
  spi: mxs: Introduce spi_cs_is_valid()
  mx53loco: Remove unneeded gpio_set_value()
  mx53loco: Add CONFIG_REVISION_TAG
  mx53loco: Turn on VUSB regulator
  mx53loco: Add mc34708 support and set mx53 frequency at 1GHz
  pmic: dialog: Avoid name conflicts
  imx: Add u-boot.imx as target for ARM9 i.MX SOCs
  i.MX2: Include asm/types.h in arch-mx25/imx-regs.h
  imx: usb: There is no such register
  i.MX25: usb: Set PORTSCx register
  imx: nand: Support flash based BBT
  i.MX25: This architecture has a GPIO4 too
  i.MX25: esdhc: Add mxc_get_clock infrastructure
  i.MX6: mx6q_sabrelite: add SATA bindings
  i.MX6: add enable_sata_clock()
  i.MX6: Add ANATOP regulator init
  mx28evk: add NAND support
  USB: ehci-mx6: Fix broken IO access
  M28: Scan only first 512 MB of DRAM to avoid memory wraparound
  Revert "i.MX28: Enable additional DRAM address bits"
  M28: Enable FDT support
  mx53loco: Add support for 1GHz operation for DA9053-based boards
  mx53loco: Allow to print CPU information at a later stage
  mx5: Add clock config interface
  imx-common: Factor out get_ahb_clk()
  i.MX6Q: mx6qsabrelite: Add keypress support to alter boot flow
  mx31pdk: Allow booting a zImage kernel
  mx6qarm2: Allow booting a zImage kernel
  mx6qsabrelite: Allow booting a zImage kernel
  mx28evk: Allow booting a zImage kernel
  m28evk: Allow to booting a dt kernel
  mx28evk: Allow to booting a dt kernel
  mx6qsabrelite: No need to set the direction for GPIO3_23 again
  pmic: Add support for the Dialog DA9053 PMIC
  MX53: mx53loco: Add SATA support
  MX53: Add support to ESG ima3 board
  SATA: add driver for MX5 / MX6 SOCs
  MX53: add function to set SATA clock to internal
  SATA: check for return value from sata functions
  MX5: Add definitions for SATA controller
  NET: fec_mxc.c: Add a way to disable auto negotiation
  Define UART4 and UART5 base addresses
  EXYNOS: Change bits per pixel value proper for u-boot.
  EXYNOS: support TRATS board display function
  LCD: support S6E8AX0 amoled driver based on EXYNOS MIPI DSI
  EXYNOS: support EXYNOS MIPI DSI interface driver.
  EXYNOS: support EXYNOS framebuffer and FIMD display drivers.
  LCD: add data structure for EXYNOS display driver
  EXYNOS: add LCD and MIPI DSI clock interface.
  EXYNOS: definitions of system resgister and power management registers.
  SMDK5250: fix compiler warning
  misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998
  misc:pmic:max8997 MAX8997 support for PMIC driver
  TRATS: modify the trats's configuration
  ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurement
  EXYNOS: Rename exynos5_tzpc structure to exynos_tzpc
  arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
  arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
  cm-t35: add I2C multi-bus support
  include/configs: Remove CONFIG_SYS_64BIT_STRTOUL
  include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF
  omap3: Introduce weak misc_init_r
  omap730p2: Remove empty misc_init_r
  omap5912osk: Remove empty misc_init_r
  omap4+: Remove CONFIG_ARCH_CPU_INIT
  omap4: Remove CONFIG_SYS_MMC_SET_DEV
  OMAP3: pandora: drop console kernel argument
  OMAP3: pandora: revise GPIO configuration
  ...
2012-05-20 21:31:26 +02:00
Lukasz Majewski
4eec44d84f usb:gadget:composite: Support for composite at gadget.h
Add device data pointer to the USB gadget's device struct.
Wrapper for extracting usb_gadget from Linux's usb device

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2012-05-20 08:32:33 +02:00
Lukasz Majewski
7010f5b94f usb:gadget:composite USB composite gadget support
USB Composite gadget implementation for u-boot. It builds on top
of USB UDC drivers.

This commit is based on following files from Linux Kernel v2.6.36:

./include/linux/usb/composite.h
./drivers/usb/gadget/composite.c

SHA1: d187abb9a83e6c6b6e9f2ca17962bdeafb4bc903

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2012-05-20 08:32:33 +02:00
Lukasz Majewski
f3b05ca533 usb:udc:samsung:cleanup Replace DEBUG_* macros with debug_cond() calls
This patch cleans up the Samsung's UDC driver. It replaces several
DEBUG_* macros with debug_cond().

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2012-05-20 08:32:33 +02:00
Lukasz Majewski
b9300531c1 usb:udc: Remove duplicated USB definitions from include/linux/usb/ch9.h file
Remove the repeated USB descriptor code and use usbdescriptors.h file.
ch9.h file has been copied from linux and is needed for USB gadget
related work.
Now usbdescriptors.h and ch9.h shall be used together.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
2012-05-20 08:32:32 +02:00
Puneet Saxena
f57661394a USB: Align buffers at cacheline
This avoids cache-alignment warnings shown in console
when a usb command is entered.

Whenever X bytes of unaligned buffer is invalidated, arm core
invalidates X + Y bytes as per the cache line size and throws
these warnings.

Signed-off-by: Puneet Saxena <puneets@nvidia.com>
Signed-off-by: Marek Vasut <marex@denx.de>
2012-05-20 08:32:32 +02:00
Joe Hershberger
13dfe94379 net: cosmetic: tftp.* checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-05-15 17:16:52 -05:00
Joe Hershberger
48522bb503 net: cosmetic: net.c checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-05-15 17:16:19 -05:00
Joe Hershberger
b28e28bbce net: cosmetic: net.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-05-15 17:13:37 -05:00
Joe Hershberger
db288a9602 net: Remove volatile from net API
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-05-15 17:10:04 -05:00
Tom Rini
49175c49ba ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORT
As originally reported against beagleboard we currently have the
following error message reported in SPL:

U-Boot SPL 2012.04-00020-gb8310b9-dirty (Apr 25 2012 - 18:49:57)
Texas Instruments Revision detection unimplemented
OMAP SD/MMC: 0
timed out in wait_for_bb: I2C_STAT=1000
reading u-boot.img
....

The reason for above message is that when booting from MMC, I2C needs to
be initialized to talk with the TWL4030.  On OMAP3 I2C is only
initalized in SPL if CONFIG_SPL_BOARD_INIT is set.

Cc: Thomas Weber <weber@corscience.de>
Cc: Steve Sakoman <sakoman@gmail.com>

Original patch for Beagleboard is:
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>

Extended to cover all other boards:
Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:41 +02:00
Tom Rini
e0820ccc38 ARM: omap3: Set SPL stack size to 8KB, image to 54KB.
With older toolchains it is possible to not fit entirely into the 45KB
that we had assigned to SPL.  Adjust to allow for 8KB of stack (which
should be more than required) and 54KB of text/data.

Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
2012-05-15 08:31:41 +02:00
Jon Hunter
c176dd0442 OMAP4: Set fdt_high for OMAP4 devices to enable booting with Device Tree
For OMAP4 boards, such as the panda-es, that have 1GB of memory the linux
kernel fails to locate the device tree blob on boot. The reason being is that
u-boot is copying the DT blob to the upper part of RAM when booting the kernel
and the kernel is unable to access the blob. By setting the fdt_high variable
to either 0xffffffff (to prevent the copy) or 0xac000000 (704MB boundary
of memory for OMAP4) the kernel is able to locate the DT blob and boot.

Based upon following patch by Dirk Behme set the fdt_high variable to allow
booting with device tree on OMAP4 boards.

"7e9603e i.mx6q: configs: Add fdt_high and initrd_high variables"

Cc: Sricharan R <r.sricharan@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2012-05-15 08:31:41 +02:00
Enric Balletbo i Serra
f1e445c3c9 igep00x0: change mpurate from 500 to auto
This patch changes the default mpurate variable from 500 to auto on
all IGEP boards, with this the default rate is autoselected.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-05-15 08:31:40 +02:00
Enric Balletbo i Serra
1b8ec016cd igep00x0: enable the use of a plain text file
Based on commit cf073e49bc for beagleboard

Using the new env import command it is possible to use plain text files instead
of script-images. Plain text files are much easier to handle.

E.g. If your boot.scr contains the following:
 -----------------------------------
setenv dvimode 1024x768-16@60
run loaduimage
run mmcboot
-----------------------------------
you could create a file named uEnv.txt and use that instead of boot.scr:
 -----------------------------------
dvimode=1024x768-16@60
uenvcmd=run loaduimage; run mmcboot
-----------------------------------
The variable uenvcmd (if existent) will be executed (using run) after uEnv.txt
was loaded. If uenvcmd doesn't exist the default boot sequence will be started,
therefore you could just use
-----------------------------------
dvimode=1024x768-16@60
-----------------------------------
as uEnv.txt because loaduimage and mmcboot is part of the default boot sequence

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-05-15 08:31:40 +02:00
Simon Glass
2cacf516df tegra: Enable keyboard for Seaboard
This enables the standard keyboard on Seaboard.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:40 +02:00
Simon Glass
4120c271c3 tegra: Switch on console mux and use environment for console
All tegra boards will use these options by default.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:40 +02:00
Rakesh Iyer
6642a681e4 tegra: Add tegra keyboard driver
Add support for internal matrix keyboard controller for Nvidia Tegra
platforms. This driver uses the fdt decode function to obtain its key
codes.

Support for the Ctrl modifier is provided. The left and right ctrl keys are
dealt with in the same way.

This uses the new keyboard input library (drivers/input/input.c) to decode
keys and handle most of the common input logic. The new key matrix library
is also used to decode (row, column) key positions into key codes.

The intent is to make this driver purely about dealing with the hardware.

Key detection before the driver is loaded is supported. This key will be
picked up when the keyboard driver is initialized.

Modified by Bernie Thompson <bhthompson@chromium.org> and
Simon Glass <sjg@chromium.org> for device tree, input layer, key matrix
and various other things.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:40 +02:00
Bernie Thompson
92c27c5193 input: Add support for keyboard matrix decoding from an fdt
Matrix keyboards require a key map to be set up, and must also deal with
key ghosting.

Create a keyboard matrix management implementation which can be leveraged
by various keyboard drivers. This includes code to read the keymap from
the FDT and perform debouncing.

Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:39 +02:00
Simon Glass
9bc590e511 input: Add generic keyboard input handler
Add a module which understands converting key codes (or scan codes)
to ASCII characters. It includes FIFO support and can call back to
drivers to read new characters when its FIFO is empty.

Keycode maps are provided for un-modified, shift and ctrl keys.

The plan is to use this module where such mapping is required.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:39 +02:00
Simon Glass
d81e270d95 input: Add linux/input.h for key code support
We want to able to decode Linux fdt keymaps, so bring part of this
enormous header file over to U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:39 +02:00
Anton Staff
bed4d89277 fdt: Add fdtdec functions to read byte array
Sometimes we don't need a full cell for each value. This provides
a simple function to read a byte array, both with and without
copying it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:39 +02:00
Simon Glass
649d0ffbc1 tegra: Enable LP0 on Seaboard
This enables LP0 to support suspend / resume on Seaboard.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:39 +02:00
Jimmy Zhang
0e35ad053f tegra: Add EMC support for optimal memory timings
Add support for setting up the memory controller parameters. Boards
can set up an appropriate table in the device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:38 +02:00
Yen Lin
5b1a5451d5 Add AES crypto library
Add support for AES using an implementation from Karl Malbrain.
This offers small code size (around 5KB on ARM) and supports 128-bit
AES only.

Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:37 +02:00
Simon Glass
1aa7e23e2b i2c: Add TPS6586X driver
This power management chip supports battery charging and a large number
of power supplies. This initial driver only provides the ability to adjust
the two synchronous buck converters SM0 and SM1 in a stepwise manner.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:37 +02:00
Simon Glass
a35925b8c1 Add abs() macro to return absolute value
This macro is generally useful to make it available in common.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15 08:31:37 +02:00
Simon Glass
3ddecfc740 fdt: Add function to return next compatible subnode
We need to iterate through subnodes of a parent, looking only at
compatible nodes. Add a utility function to do this for us.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:36 +02:00
Simon Glass
96875e7d3b fdt: Add function to locate an array in the device tree
fdtdec_locate_array() locates an integer array but does not copy it. This
saves the caller having to allocated wasted space.

Access to array elements should be through the fdt32_to_cpu() macro.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:36 +02:00
Marek Vasut
f8c4a86b5e i.MX28: Implement boot pads sampling and reporting
This patch implements code that samples i.MX28 boot pads and reports boot mode
accordingly.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2012-05-15 08:31:35 +02:00
Marek Vasut
9a0f98d397 M28EVK: Add SD update command
Add "update_sd_firmware" command to easily reload the SD card of
m28evk kit. This comes handy when the board boots from SD card.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2012-05-15 08:31:35 +02:00
Fabio Estevam
54cd1dee8f mx53loco: Add CONFIG_REVISION_TAG
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG information.

The kernel uses this data to distinguish between Dialog versus mc34708 based boards,
and also to distinguish between revA and revB of the mc34708 based boards.

Suggested-by: Yu Li <yk@magniel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:34 +02:00
Fabio Estevam
768a059710 mx53loco: Turn on VUSB regulator
On the mx53loco board with mc34708 PMIC it is necessary to turn on VUSB regulator
so that the mx53 USBH1 PHY receives the 3.3V voltage.

Tested by inserting a USB pen drive in the upper USB slot (USBH1) and then issued the
commands:

usb start

usb info

,which correctly detected and printed the USB pen drive information.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:34 +02:00
Fabio Estevam
5b547f3c20 mx53loco: Add mc34708 support and set mx53 frequency at 1GHz
Add mc34708 support and set mx53 core frequency at its maximum value of 1GHz.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:34 +02:00
Fabio Estevam
ed5157e889 pmic: dialog: Avoid name conflicts
As mx53loco board has two variants: one with Dialog PMIC and another with FSL MC34708 PMIC,
we need to be able to build both drivers.

Change pmic_init() and PMIC_NUM_OF_REGS names to avoid build conflicts when both drivers are present.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:34 +02:00
Eric Nelson
3996a96c5e i.MX6: mx6q_sabrelite: add SATA bindings
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: stefano Babic <sbabic@denx.de>
2012-05-15 08:31:33 +02:00
Lauri Hintsala
ecb7be2985 mx28evk: add NAND support
NAND support is not enabled by default because Eval Kit is not delivered
with NAND chip. To enable NAND support add CONFIG_CMD_NAND to board config.

Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-05-15 08:31:33 +02:00
Marek Vasut
feef24ee11 M28: Scan only first 512 MB of DRAM to avoid memory wraparound
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
2012-05-15 08:31:32 +02:00
Marek Vasut
6725ebdff5 M28: Enable FDT support
This will eventually be needed with Linux 3.5, which will be the point when
MXS will be switched to FDT.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
2012-05-15 08:31:32 +02:00
Fabio Estevam
e7e337227b mx53loco: Add support for 1GHz operation for DA9053-based boards
There are two types of mx53loco boards: initial boards were built with a Dialog
DA9053 PMIC and more recent version is based on a Freescale MC34708 PMIC.

Add DA9053 PMIC support and adjust the required voltages and clocks for running
the CPU at 1GHz.

Tested on both versions of mx53loco boards.

In the case of a MC34708-based board the CPU operating voltage remains at 800MHz.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by : Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:32 +02:00
Fabio Estevam
1fc56f1cb0 mx53loco: Allow to print CPU information at a later stage
Print CPU information within board_late_init().

This is in preparation for adding 1GHz support, which requires programming a PMIC
via I2C. As I2C is only available after relocation, print the CPU information
later at board_late_init(), so that the CPU frequency can be printed correctly.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:32 +02:00
Eric Nelson
28fdbddc94 i.MX6Q: mx6qsabrelite: Add keypress support to alter boot flow
Uses the 'magic_keys' idiom as described in doc/README.kbd:
	http://lists.denx.de/pipermail/u-boot/2012-April/122502.html

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:32 +02:00
Fabio Estevam
0c23d84c86 mx31pdk: Allow booting a zImage kernel
Allow booting a zImage kernel.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15 08:31:32 +02:00
Fabio Estevam
f0e77b35be mx6qarm2: Allow booting a zImage kernel
Allow booting a zImage kernel.

Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
2012-05-15 08:31:32 +02:00
Fabio Estevam
5fbfd1c29b mx6qsabrelite: Allow booting a zImage kernel
Allow booting a zImage kernel.

Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15 08:31:31 +02:00
Fabio Estevam
34990e1206 mx28evk: Allow booting a zImage kernel
Allow booting a zImage kernel.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15 08:31:31 +02:00
Fabio Estevam
b91ce01841 m28evk: Allow to booting a dt kernel
Allow to booting a dt kernel.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15 08:31:31 +02:00
Fabio Estevam
e310016bdf mx28evk: Allow to booting a dt kernel
Allow to booting a dt kernel.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15 08:31:31 +02:00
Fabio Estevam
20831061d8 pmic: Add support for the Dialog DA9053 PMIC
Add support for the Dialog DA9053 PMIC.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15 08:31:31 +02:00
Stefano Babic
f92e4e6c19 MX53: mx53loco: Add SATA support
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
2012-05-15 08:31:31 +02:00
Stefano Babic
79656d27b3 MX53: Add support to ESG ima3 board
The ESG ima3-mx53 board is based on the Freescale
i.MX53 SOC. It boots from NOR (128 MB) and
supports Ethernet (FEC), SATA.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:31 +02:00
Stefano Babic
9f472e6540 SATA: add driver for MX5 / MX6 SOCs
This driver is part of Freescale's LTIB for
MX5 / MX6.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Terry Lv <r65388@freescale.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
2012-05-15 08:31:30 +02:00
Donghwa Lee
51b1cd6df7 EXYNOS: support TRATS board display function
This patch support TRATS board configuration and display function.

Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15 08:31:30 +02:00
Donghwa Lee
559a05cc32 LCD: add data structure for EXYNOS display driver
Add vidinfo data structure for EXYNOS display driver

Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
2012-05-15 08:31:29 +02:00
Łukasz Majewski
04ce68eee3 misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998
TRATS target uses MAX8997 PMIC device instead of MAX8998.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15 08:31:29 +02:00
Łukasz Majewski
8504296045 misc:pmic:max8997 MAX8997 support for PMIC driver
This commit adds support for MAX8997 PMIC driver.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:29 +02:00
Jaehoon Chung
e687c5a8be TRATS: modify the trats's configuration
Trats is supported 1GiB memory size.
(Each bank size is 512MB.)
And INITRD is unnecessary. So removed them.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15 08:31:28 +02:00
Łukasz Majewski
4d86bf0860 ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurement
This patch enables LDO4 power line for preparing proper voltages to be
measured by ADC converter.
This measurement is used for determination of target board HW revision.

Test HW:
Universal_C210 (Exynos4210) rev. 0.0

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15 08:31:28 +02:00
Nobuhiro Iwamatsu
2d594fd55d arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
With almost all the architecture and board BOARD_LATE_INIT does not use.
CONFIG_BOARD_LATE_INIT is used instead.
This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:28 +02:00
Nobuhiro Iwamatsu
8913e6b3c3 arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
With almost all the architecture and board BOARD_LATE_INIT does not use.
CONFIG_BOARD_LATE_INIT is used instead.
This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2012-05-15 08:31:28 +02:00
Nikita Kiryanov
79874ae934 cm-t35: add I2C multi-bus support
Enable I2C multi-bus support and config I2C muxes for I2C2 and I2C3.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-05-15 08:31:28 +02:00
Tom Rini
4ac16f2bbd include/configs: Remove CONFIG_SYS_64BIT_STRTOUL
This define does not control anything, remove it.

Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:28 +02:00
Tom Rini
1005ccfda4 include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF
This define does not control anything, remove it.

Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:28 +02:00
Tom Rini
60bd10df8a omap730p2: Remove empty misc_init_r
We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R

Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:27 +02:00
Tom Rini
b8f4a728e6 omap5912osk: Remove empty misc_init_r
We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R

Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:27 +02:00
Tom Rini
aa2889c8c3 omap4+: Remove CONFIG_ARCH_CPU_INIT
OMAP4/5 had an empty arch_cpu_init() so drop that along with
CONFIG_ARCH_CPU_INIT

Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:27 +02:00
Tom Rini
4335517088 omap4: Remove CONFIG_SYS_MMC_SET_DEV
This is only used on !CONFIG_GENERIC_MMC which is false here.

Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:27 +02:00