We should use the cmd/ directory for commands rather than for common code
used elsewhere in U-Boot. Move the common 'source' code into
image-board.c to achieve this.
The image_source_script() function needs to call run_command_list() so
seems to belong better in the command library. Move and rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The eMMC card has two supplies, VCC and VCCQ. The VCC supplies the NAND
array and the VCCQ supplies the bus. On Condor, the VCC is connected to
3.3V rail, while the VCCQ is connected to 1.8V rail. Adjust the pinmux
to match the bus, which is always operating in 1.8V mode.
Based on Linux commit 69efe4bbeda50745 ("arm64: dts: renesas: condor:
Switch eMMC bus to 1V8") from Wolfram Sang
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
This board requires SPI NOR fast-read, otherwise the SPI NOR
access returns corrupted data. Enable the fast-read explicitly
in DT as it has been disabled in the MTD subsystem by commit
d008190920 ("mtd: spi-nor: Mask out fast read if not requested in DT")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
-----BEGIN PGP SIGNATURE-----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=SNID
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230113' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add driver to manage onboard hub supplies
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
With U-Boot having access to ROM API call table, it is possible to use
the ROM API call it authenticate e.g. signed kernel fitImages using the
BootROM ECDSA support. Make this available by pulling the ECDSA BootROM
call support from SPL-only guard.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The ROM API table pointer is no longer accessible from U-Boot, fix
this by passing the ROM API pointer through. This makes it possible
for U-Boot to call ROM API functions to authenticate payload like
signed fitImages.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The STM32MP15xx platform currently comes with two incompatible
implementations of save_boot_params() weak function override.
Factor the save_boot_params() implementation into common cpu.c
code and provide accessors to read out both ROM API table address
and DT address from any place in the code instead.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
In case Dcache is enabled while the ECDSA authentication function is
called via BootROM ROM API, the MMU tables are set up and the BootROM
region is not marked as executable, so an attempt to run code from it
results in a hang. Mark the BootROM region as executable as suggested
by Patrick to prevent the hang.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
_relocate() needs the information in .rela* for self relocation
of the EFI binary.
Fixes: d7ddeb66a6 ("efi_loader: fix building aarch64 EFI binaries")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The fs_loader device is used to pull in settings via the chosen node.
However, there was no library function for this, so arria10 was doing it
explicitly. This function subsumes that, and uses ofnode_get_chosen_node
instead of navigating the device tree directly. Because fs_loader pulls
its config from the environment by default, it's fine to create a device
with nothing backing it at all. Doing this allows enabling
CONFIG_FS_LOADER without needing to modify the device tree.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for "st,stm32mp13-bsec" for STM32MP13x in the
bsec driver based on OP-TEE pseudo TA STM32MP BSEC.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When OP-TEE is used, the SMC for BSEC management are not available and
the STM32MP BSEC pseudo TA must be used (it is mandatory for STM32MP13
and it is a new feature for STM32MP15x).
The BSEC driver try to open a session to this PTA BSEC at probe
and use it for OTP read or write access to fuse or to shadow.
This patch also adapts the commands stm32key and stboard to handle
the BSEC_LOCK_PERM lock value instead of 1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove unnecessary return in stm32mp_bsec_write_lock and replace tab
by space for plat_auto opts.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The timer units in the stm32mp15x CPUs have interrupts, depending on the
timer flavour either one "global" or four dedicated ones. Add the irqs
to the timer units on stm32mp15x.
Sync the DT Files with linux kernel v6.1 and with commit a9b70102253ce
("ARM: dts: stm32: Add timer interrupts on stm32mp15")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove unnecessary space in device tree stm32mp15xx-dkx.dtsi.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The include file stm32mp1-clksrc.h is not necessary for the SCMI STM32MP15
dtsi files as the clock tree is not defined in the U-Boot SCMI device tree;
these SCMI device tree only support TFABOOT with stm32mp15_defconfig,
SPL with the basic boot defconfig is not supported.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for USB2514B onboard hub on stm32mp157c EV1 board. The HUB
is supplied by a 3v3 PMIC regulator.
[backport from linux ad9591b01d24]
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
phy-stm32-usbphyc bindings uses a connector node with vbus-supply
property.
[backport from linux 43e55d778a6b]
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Having NXP specific items in the main menu is confusing. Especially
the comment line
*** Other functionality shared between NXP SoCs ***
is simply misleading.
Move all NXP stuff into a separate sub-menu.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Put all entries for skipping low-level initialization into a sub-menu.
Use different titles for main U-Boot, SPL, TPL.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Before this was named just evm, which doesn't match the naming
of the other TI board file directory and makes it look like a
common directory for evms. Name this omap3evm.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Derald Woods <woods.technical@gmail.com>
KASLR address is needed to boot fully functional Android.
KASLR is set by primary bootloader, and since u-boot is used
as a secondary bootloader(replacing kernel) on sdm845 platform,
KASLR may be found by comparing memory chunks at relocaddr over
supposed KASLR range.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Texas Instruments has begun enabling security settings on the SoCs it
produces to instruct ROM and TIFS to begin protecting the Security
Management Subsystem (SMS) from other binaries we load into the chip by
default.
One way ROM and TIFS do this is by enabling firewalls to protect the
OCSRAM and HSM RAM regions they're using during bootup.
The HSM RAM the wakeup SPL is in is firewalled by TIFS to protect
itself from the main domain applications. This means the 'bootindex'
value in HSM RAM, left by ROM to indicate if we're using the primary
or secondary boot-method, must be moved to OCSRAM (that TIFS has open
for us) before we make the jump to the main domain so the main domain's
bootloaders can keep access to this information.
Signed-off-by: Bryan Brattlof <bb@ti.com>
The boot mode detection assumes that BOOT_DEVICE_MMC2 should always
result in MMCSD_MODE_FS, but MMCSD_MODE_RAW is also a valid option for
this port.
The current logic also avoids looking at the bootmode pin strapping,
which should be the primary means of determining whether a device is
being booted in MMCSD_MODE_EMMCBOOT mode.
Switch around the logic to check the boot mode to determine whether the
eMMC boot mode is expected or MMC/SD boot mode. From there we can look
at the boot mode config if in MMC/SD boot mode to determine whether to
attempt RAW or FS based booting.
This change allows U-Boot to also be successfully booted from RAW
offsets in addition to from a filesystem.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
When building with binutils 2.39 warnings
*_efi.so has a LOAD segment with RWX permissions
occur.
Use SHF_WRITE | SHF_ALLOC as section flags for the .data section.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmO2mnEcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBAOB/4y7e9y0jdKSWDwMdZj
enXK/U/GREFyuiSdadil0aJl9WfayjwZkh7uHSTj4pi9ApNivfoqsL7WZYpJxhRD
WlpNhs3TZ70i8CgKUosdzcpquAQZUZhg6iV5DCObrK6yNJRGOXLIwMOd+vw/Xz6/
YTGqzivEDMBuH/9HLuC0m+26PEpff8nenNEjC2k8ssG26ojLz7oCQh2HoHcSgNRc
HkEYlFJ/Le8kM8Ak2F3ebmsfgMTnFrRVwV1BsZa5vO0BrMYgJCORsl7Cnfcw6/2N
LEHG7kwlSorJeETn/gkLiZ+NyqzU+oFH0jGRZ5Ciqg1qcCO3k9yBMgWQzd7nTL6C
5oZA
=Ocdd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.04 cycle:
This feature set includes the new DM-based NAND flash driver (old non-DM
driver is still kept for backwards compatibility), and the move to DM
NAND flash driver for sam9x60ek board. Feature set also includes
devicetree alignment for sama7g5 with Linux, devicetree alignment on USB
with Linux for all boards (sama5, sam9x60), chip id for sama7g5, minor
configs and tweaks.
commit 777aaaa706 ("common/memsize.c: Fix get_effective_memsize() to check
for overflow") because the effective DDR effective size is reduce by 4KiB
and sometime the board hang on boot
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmO3+ZUACgkQ4rK92eCq
k3VHfQf9Fd9zjv8ljJoTW4IHjh0hW4M7KJJ44OplpxgLBKy9lO1LCGxF3V5EAdGM
yBQsRfAjBKiTx8bM7d30dZ2SbQOMjVgbI+VDYI1Pyzzo6wkmrc5uKj16/1Zt9FbR
M26ftJ07uT4hOinD2WXhD4LKH9oMM4p7d03P1q4PPbFPR5+37UEU01fLlCH+SW0R
ajUVPdG+2Pn8g6+rjfVo27dZPi02PBVe8ODvEt63hwMkXqcfHFGMlP4d9vIrArcH
Q9vt1YeyaK+lQdpvctTaH2iw13JtJKpJZxsw63sMOU3+PWFneIKD0gSUKGWrKRnI
kfIKfSU4mJB2+Xeq+2M7O5nLYXT9kA==
=OFHo
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230106' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- stm32mp: Fix board_get_usable_ram_top(): workaround to avoid issue after the
commit 777aaaa706 ("common/memsize.c: Fix get_effective_memsize() to check
for overflow") because the effective DDR effective size is reduce by 4KiB
and sometime the board hang on boot
The QSPI is accessed via the RPC-IF, but the compatible flags
previously used a different name. This compatibel name was changed
which broke the ability to access the QSPI. Fix this by removing
the custom naming reference.
Fixes: 68083b897b ("renesas: Fix RPC-IF compatible values")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Since commit 2f96d4dd95 ("imx7s/d: synchronise device trees with linux")
the imx7d-pico board no longer boots.
The reason is that prior to the above commit there was an explicit
inclusion of arch/arm/dts/imx7d-pico-u-boot.dtsi inside imx7d-pico.dtsi.
After the syncing with the Linux upstream dtsi, this u-boot.dtsi inclusion
is gone and the board fails to boot.
U-Boot uses the imx7d-pico-pi.dtb file, so rename the u-boot.dtsi to
imx7d-pico-pi-u-boot.dtsi which gets included automatically by U-Boot
standard make logic and makes the board boot again.
Signed-off-by: Fabio Estevam <festevam@denx.de>
U-Boot build system builds final U-Boot binary for socrates board in custom
file u-boot-socrates.bin (instead of standard u-boot.bin). Output target
file u-boot-socrates.bin is generated by binman as defined in board binman
config file arch/powerpc/dts/socrates-u-boot.dtsi.
But binman was disabled in commit 5af42eafd7 ("Makefile: Reduce usage of
custom mpc85xx u-boot.bin target") for all mpc85xx boards which do not use
standard powerpc binman config file arch/powerpc/dts/u-boot.dtsi and boards
which do not require binman at all.
The only such mpc85xx board is socrates. So since that commit, U-Boot does
not final binary for socrates board anymore.
Fix this issue by re-enabling binman for socrates board. And build process
starts again producing u-boot-socrates.bin binary.
Note that build process for this socrates board always produce u-boot.bin
binary which is broken and not usable for socrates board. Long term
solution should be to disable building broken binary u-boot.bin and then
renaming u-boot-socrates.bin to u-boot.bin, or switching to use common
powerpc binman config file arch/powerpc/dts/socrates-u-boot.dtsi (if it is
possible).
Fixes: 5af42eafd7 ("Makefile: Reduce usage of custom mpc85xx u-boot.bin target")
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Heiko Schocher <hs@denx.de>
Do not access gd->ram_size and assume this is actual valid RAM size. Since commit
777aaaa706 ("common/memsize.c: Fix get_effective_memsize() to check for overflow")
the RAM size may be less than gd->ram_size , call get_effective_memsize() to get
the limited value instead.
The aforementioned commit makes STM32MP15xx boards with 1 GiB of DRAM
at 0xc0000000 hang on boot, which is a grave defect.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add the required pinctrl, gpio and phy properties required by the
USB DT nodes of the sama7g5ek boards. Since these have not yet been
defined in upstream Linux, place them in the U-Boot specific DT file.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Define the USB and UTMI DT nodes for the sama7g5 SoC's. Since these have
not yet been defined in upstream Linux, place them in the U-Boot specific
DT file.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add the required pinctrl and gpio properties required by the USB DT
nodes of the sam9x60ek boards.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Add the required pinctrl and gpio properties needed by the USB DT nodes
of the sam9x60_curiosity boards.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
While our EFI binaries execute without problems on EDK II they crash on
a Lenovo X13s. Let our binaries look more like what EDK II produces:
* move all writable data to a .data section
* align sections to 4 KiB boundaries (matching EFI page size)
* remove IMAGE_SCN_LNK_NRELOC_OVFL from .reloc section flags
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Remove init of UART-clock and UART-reset in arch_cpu_init(). Add DEBUG_UART
to s5p4418_nanopi2_defconfig.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
All uniphier v7 SoCs have cortex-a9 and use cortex-a9 global timer
in a simple implementation. Now DM_TIMER of it is available
on 35751c7f3f ("timer: sti: convert sti-timer to arm a9 global timer"),
so let's switch to it.
The old driver reads the lower 32bits of counter field
and sets the prescaler as 50 with PERIPHCLK(=50MHz),
so the global timer works as a 32-bit 1MHz timer.
The DM_TIMER uses the whole 64bits with no prescaler,
so the global timer works as a 64-bit PERIPHCLK timer.
CONFIG_SYS_HZ_CLOCK is set as the default PERIPHCLK frequency,
if there is no 'clocks' property in devicetree.
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
