mirror of
https://github.com/u-boot/u-boot.git
synced 2025-01-25 04:03:25 +08:00
exynos: video: Drop old unused code
Now that we are using driver model, we can drop the weak functions and LCD init in the board file. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit is contained in:
Simon Glass
Minkyu Kang
parent
bb5930d5c9
commit
f4f2fce70c
@ -147,159 +147,6 @@ int board_get_revision(void)
|
||||
return 0;
|
||||
}
|
||||
|
||||
#ifdef CONFIG_LCD
|
||||
|
||||
static int board_dp_bridge_init(struct udevice *dev)
|
||||
{
|
||||
const int max_tries = 10;
|
||||
int num_tries;
|
||||
int ret;
|
||||
|
||||
debug("%s\n", __func__);
|
||||
ret = video_bridge_attach(dev);
|
||||
if (ret) {
|
||||
debug("video bridge init failed: %d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
/*
|
||||
* We need to wait for 90ms after bringing up the bridge since there
|
||||
* is a phantom "high" on the HPD chip during its bootup. The phantom
|
||||
* high comes within 7ms of de-asserting PD and persists for at least
|
||||
* 15ms. The real high comes roughly 50ms after PD is de-asserted. The
|
||||
* phantom high makes it hard for us to know when the NXP chip is up.
|
||||
*/
|
||||
mdelay(90);
|
||||
|
||||
for (num_tries = 0; num_tries < max_tries; num_tries++) {
|
||||
/* Check HPD. If it's high, or we don't have it, all is well */
|
||||
ret = video_bridge_check_attached(dev);
|
||||
if (!ret || ret == -ENOENT)
|
||||
return 0;
|
||||
|
||||
debug("%s: eDP bridge failed to come up; try %d of %d\n",
|
||||
__func__, num_tries, max_tries);
|
||||
}
|
||||
|
||||
/* Immediately go into bridge reset if the hp line is not high */
|
||||
return -EIO;
|
||||
}
|
||||
|
||||
static int board_dp_bridge_setup(const void *blob)
|
||||
{
|
||||
const int max_tries = 2;
|
||||
int num_tries;
|
||||
struct udevice *dev;
|
||||
int ret;
|
||||
|
||||
/* Configure I2C registers for Parade bridge */
|
||||
ret = uclass_get_device(UCLASS_VIDEO_BRIDGE, 0, &dev);
|
||||
if (ret) {
|
||||
debug("video bridge init failed: %d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
if (strncmp(dev->driver->name, "parade", 6)) {
|
||||
/* Mux HPHPD to the special hotplug detect mode */
|
||||
exynos_pinmux_config(PERIPH_ID_DPHPD, 0);
|
||||
}
|
||||
|
||||
for (num_tries = 0; num_tries < max_tries; num_tries++) {
|
||||
ret = board_dp_bridge_init(dev);
|
||||
if (!ret)
|
||||
return 0;
|
||||
if (num_tries == max_tries - 1)
|
||||
break;
|
||||
|
||||
/*
|
||||
* If we're here, the bridge chip failed to initialise.
|
||||
* Power down the bridge in an attempt to reset.
|
||||
*/
|
||||
video_bridge_set_active(dev, false);
|
||||
|
||||
/*
|
||||
* Arbitrarily wait 300ms here with DP_N low. Don't know for
|
||||
* sure how long we should wait, but we're being paranoid.
|
||||
*/
|
||||
mdelay(300);
|
||||
}
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
void exynos_cfg_lcd_gpio(void)
|
||||
{
|
||||
/* For Backlight */
|
||||
gpio_request(EXYNOS5_GPIO_B20, "lcd_backlight");
|
||||
gpio_cfg_pin(EXYNOS5_GPIO_B20, S5P_GPIO_OUTPUT);
|
||||
gpio_set_value(EXYNOS5_GPIO_B20, 1);
|
||||
}
|
||||
|
||||
static int board_dp_set_backlight(int percent)
|
||||
{
|
||||
struct udevice *dev;
|
||||
int ret;
|
||||
|
||||
ret = uclass_get_device(UCLASS_VIDEO_BRIDGE, 0, &dev);
|
||||
if (!ret)
|
||||
ret = video_bridge_set_backlight(dev, percent);
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
void exynos_backlight_on(unsigned int on)
|
||||
{
|
||||
struct udevice *dev;
|
||||
int ret;
|
||||
|
||||
debug("%s(%u)\n", __func__, on);
|
||||
if (!on)
|
||||
return;
|
||||
|
||||
ret = regulator_get_by_platname("vcd_led", &dev);
|
||||
if (!ret)
|
||||
ret = regulator_set_enable(dev, true);
|
||||
if (ret)
|
||||
debug("Failed to enable backlight: ret=%d\n", ret);
|
||||
|
||||
/* T5 in the LCD timing spec (defined as > 10ms) */
|
||||
mdelay(10);
|
||||
|
||||
/* board_dp_backlight_pwm */
|
||||
gpio_direction_output(EXYNOS5_GPIO_B20, 1);
|
||||
|
||||
/* T6 in the LCD timing spec (defined as > 10ms) */
|
||||
mdelay(10);
|
||||
|
||||
/* try to set the backlight in the bridge registers */
|
||||
ret = board_dp_set_backlight(80);
|
||||
|
||||
/* if we have no bridge or it does not support backlight, use a GPIO */
|
||||
if (ret == -ENODEV || ret == -ENOSYS) {
|
||||
gpio_request(EXYNOS5_GPIO_X30, "board_dp_backlight_en");
|
||||
gpio_direction_output(EXYNOS5_GPIO_X30, 1);
|
||||
}
|
||||
}
|
||||
|
||||
void exynos_lcd_power_on(void)
|
||||
{
|
||||
struct udevice *dev;
|
||||
int ret;
|
||||
|
||||
debug("%s\n", __func__);
|
||||
ret = regulator_get_by_platname("lcd_vdd", &dev);
|
||||
if (!ret)
|
||||
ret = regulator_set_enable(dev, true);
|
||||
if (ret)
|
||||
debug("Failed to enable LCD panel: ret=%d\n", ret);
|
||||
|
||||
ret = board_dp_bridge_setup(gd->fdt_blob);
|
||||
if (ret && ret != -ENODEV)
|
||||
printf("LCD bridge failed to enable: %d\n", ret);
|
||||
}
|
||||
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_USB_DWC3
|
||||
static struct dwc3_device dwc3_device_data = {
|
||||
.maximum_speed = USB_SPEED_SUPER,
|
||||
|
||||
@ -479,39 +479,6 @@ unsigned long exynos_fimd_calc_fbsize(struct exynos_fb_priv *priv)
|
||||
return priv->vl_col * priv->vl_row * (VNBITS(priv->vl_bpix) / 8);
|
||||
}
|
||||
|
||||
__weak void exynos_cfg_lcd_gpio(void)
|
||||
{
|
||||
}
|
||||
|
||||
__weak void exynos_backlight_on(unsigned int onoff)
|
||||
{
|
||||
}
|
||||
|
||||
__weak void exynos_reset_lcd(void)
|
||||
{
|
||||
}
|
||||
|
||||
__weak void exynos_lcd_power_on(void)
|
||||
{
|
||||
}
|
||||
|
||||
__weak void exynos_cfg_ldo(void)
|
||||
{
|
||||
}
|
||||
|
||||
__weak void exynos_enable_ldo(unsigned int onoff)
|
||||
{
|
||||
}
|
||||
|
||||
__weak void exynos_backlight_reset(void)
|
||||
{
|
||||
}
|
||||
|
||||
__weak int exynos_lcd_misc_init(struct vidinfo *vid)
|
||||
{
|
||||
return 0;
|
||||
}
|
||||
|
||||
int exynos_fb_ofdata_to_platdata(struct udevice *dev)
|
||||
{
|
||||
struct exynos_fb_priv *priv = dev_get_priv(dev);
|
||||
|
||||
@ -1,41 +0,0 @@
|
||||
/*
|
||||
* Copyright (C) 2012 Samsung Electronics
|
||||
*
|
||||
* Author: InKi Dae <inki.dae@samsung.com>
|
||||
* Author: Donghwa Lee <dh09.lee@samsung.com>
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#ifndef _EXYNOS_FB_H_
|
||||
#define _EXYNOS_FB_H_
|
||||
|
||||
#include <asm/arch/fb.h>
|
||||
|
||||
#define MAX_CLOCK (86 * 1000000)
|
||||
|
||||
enum exynos_cpu_auto_cmd_rate {
|
||||
DISABLE_AUTO_FRM,
|
||||
PER_TWO_FRM,
|
||||
PER_FOUR_FRM,
|
||||
PER_SIX_FRM,
|
||||
PER_EIGHT_FRM,
|
||||
PER_TEN_FRM,
|
||||
PER_TWELVE_FRM,
|
||||
PER_FOURTEEN_FRM,
|
||||
PER_SIXTEEN_FRM,
|
||||
PER_EIGHTEEN_FRM,
|
||||
PER_TWENTY_FRM,
|
||||
PER_TWENTY_TWO_FRM,
|
||||
PER_TWENTY_FOUR_FRM,
|
||||
PER_TWENTY_SIX_FRM,
|
||||
PER_TWENTY_EIGHT_FRM,
|
||||
PER_THIRTY_FRM,
|
||||
};
|
||||
|
||||
void exynos_fimd_lcd_init_mem(unsigned long screen_base, unsigned long fb_size,
|
||||
unsigned long palette_size);
|
||||
void exynos_fimd_lcd_init(struct vidinfo *vid, ulong lcd_base_address);
|
||||
unsigned long exynos_fimd_calc_fbsize(struct vidinfo *pvid);
|
||||
|
||||
#endif
|
||||
Loading…
Reference in New Issue
Block a user