mirror of
https://github.com/u-boot/u-boot.git
synced 2024-11-28 15:13:31 +08:00
nand: Add support for unlock.invert
NAND unlock command allows an invert bit to be set to unlock all but the selected page range. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [scottwood@freescale.com: updated docs and added comment about invert bit] Signed-off-by: Scott Wood <scottwood@freescale.com>
This commit is contained in:
parent
d62e9caaaf
commit
eee623a504
@ -749,11 +749,18 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
|
||||
return 0;
|
||||
}
|
||||
|
||||
if (strcmp(cmd, "unlock") == 0) {
|
||||
if (strncmp(cmd, "unlock", 5) == 0) {
|
||||
int allexcept = 0;
|
||||
|
||||
s = strchr(cmd, '.');
|
||||
|
||||
if (s && !strcmp(s, ".allexcept"))
|
||||
allexcept = 1;
|
||||
|
||||
if (arg_off_size(argc - 2, argv + 2, &dev, &off, &size) < 0)
|
||||
return 1;
|
||||
|
||||
if (!nand_unlock(&nand_info[dev], off, size)) {
|
||||
if (!nand_unlock(&nand_info[dev], off, size, allexcept)) {
|
||||
puts("NAND flash successfully unlocked\n");
|
||||
} else {
|
||||
puts("Error unlocking NAND flash, "
|
||||
@ -807,7 +814,7 @@ U_BOOT_CMD(
|
||||
"\n"
|
||||
"nand lock [tight] [status]\n"
|
||||
" bring nand to lock state or display locked pages\n"
|
||||
"nand unlock [offset] [size] - unlock section"
|
||||
"nand unlock[.allexcept] [offset] [size] - unlock section"
|
||||
#endif
|
||||
#ifdef CONFIG_ENV_OFFSET_OOB
|
||||
"\n"
|
||||
|
@ -228,6 +228,8 @@ NAND locking command (for chips with active LOCKPRE pin)
|
||||
"nand unlock [offset] [size]"
|
||||
unlock consecutive area (can be called multiple times for different areas)
|
||||
|
||||
"nand unlock.allexcept [offset] [size]"
|
||||
unlock all except specified consecutive area
|
||||
|
||||
I have tested the code with board containing 128MiB NAND large page chips
|
||||
and 32MiB small page chips.
|
||||
|
@ -317,18 +317,20 @@ int nand_get_lock_status(struct mtd_info *mtd, loff_t offset)
|
||||
* @param start start byte address
|
||||
* @param length number of bytes to unlock (must be a multiple of
|
||||
* page size nand->writesize)
|
||||
* @param allexcept if set, unlock everything not selected
|
||||
*
|
||||
* @return 0 on success, -1 in case of error
|
||||
*/
|
||||
int nand_unlock(struct mtd_info *mtd, ulong start, ulong length)
|
||||
int nand_unlock(struct mtd_info *mtd, ulong start, ulong length, int allexcept)
|
||||
{
|
||||
int ret = 0;
|
||||
int chipnr;
|
||||
int status;
|
||||
int page;
|
||||
struct nand_chip *chip = mtd->priv;
|
||||
printf ("nand_unlock: start: %08x, length: %d!\n",
|
||||
(int)start, (int)length);
|
||||
|
||||
debug("nand_unlock%s: start: %08x, length: %d!\n",
|
||||
allexcept ? " (allexcept)" : "", start, length);
|
||||
|
||||
/* select the NAND device */
|
||||
chipnr = (int)(start >> chip->chip_shift);
|
||||
@ -368,6 +370,15 @@ int nand_unlock(struct mtd_info *mtd, ulong start, ulong length)
|
||||
|
||||
/* submit ADDRESS of LAST page to unlock */
|
||||
page += (int)(length >> chip->page_shift);
|
||||
|
||||
/*
|
||||
* Page addresses for unlocking are supposed to be block-aligned.
|
||||
* At least some NAND chips use the low bit to indicate that the
|
||||
* page range should be inverted.
|
||||
*/
|
||||
if (allexcept)
|
||||
page |= 1;
|
||||
|
||||
chip->cmdfunc(mtd, NAND_CMD_UNLOCK2, -1, page & chip->pagemask);
|
||||
|
||||
/* call wait ready function */
|
||||
|
@ -144,8 +144,8 @@ int nand_erase_opts(nand_info_t *meminfo, const nand_erase_options_t *opts);
|
||||
#define NAND_LOCK_STATUS_LOCK 0x02
|
||||
#define NAND_LOCK_STATUS_UNLOCK 0x04
|
||||
|
||||
int nand_lock( nand_info_t *meminfo, int tight );
|
||||
int nand_unlock( nand_info_t *meminfo, ulong start, ulong length );
|
||||
int nand_lock(nand_info_t *meminfo, int tight);
|
||||
int nand_unlock(nand_info_t *meminfo, ulong start, ulong length, int allexcept);
|
||||
int nand_get_lock_status(nand_info_t *meminfo, loff_t offset);
|
||||
|
||||
int nand_spl_load_image(uint32_t offs, unsigned int size, void *dst);
|
||||
|
Loading…
Reference in New Issue
Block a user