diff --git a/board/davinci/da8xxevm/README.omapl138-lcdk b/board/davinci/da8xxevm/README.omapl138-lcdk
deleted file mode 100644
index ea0c53d043d..00000000000
--- a/board/davinci/da8xxevm/README.omapl138-lcdk
+++ /dev/null
@@ -1,28 +0,0 @@
-Summary
-=======
-This README assumes you have read README.da850.  It contains some additional
-information specific to building the omapl138-lcdk.  The AIS file as generated
-by the build is, currently, not useable due to differences in the flash
-available on this board, as compared to the da850evm boards.
-
-Flash Differences
-=================
-Refer to the discussion in [1] for more detail - basically the da850evm uses
-SPI flash whereas the lcdk uses NAND flash to store the bootloader, and
-the support isn't there in the SPL code.
-
-It should be possible to add the support in the SPL code should someone be
-sufficiently motivated.
-
-Using the built image
-=====================
-The output image to use is u-boot.bin.  This needs to be converted to an
-AIS file as described in [1] and then flashed using the utitilty linked to
-there and also described in README.da850.  You _may_ be able to write using
-u-boot itself, but the commands in README.da850 won't work as they write to
-SPI rather than NAND.
-
-Links
-=====
-[1]
- http://e2e.ti.com/support/dsp/omap_applications_processors/f/42/t/386829
\ No newline at end of file
diff --git a/configs/omapl138_lcdk_defconfig b/configs/omapl138_lcdk_defconfig
index 4a5f435550b..52681c92d02 100644
--- a/configs/omapl138_lcdk_defconfig
+++ b/configs/omapl138_lcdk_defconfig
@@ -3,6 +3,7 @@ CONFIG_ARCH_DAVINCI=y
 CONFIG_TARGET_OMAPL138_LCDK=y
 CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SPL_NAND_SUPPORT=y
 CONFIG_SPL_SERIAL_SUPPORT=y
 CONFIG_BOOTDELAY=3
 CONFIG_VERSION_VARIABLE=y
@@ -23,6 +24,8 @@ CONFIG_CMD_PING=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_UBI=y
+CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
+CONFIG_SYS_NAND_U_BOOT_OFFS=0x28000
 CONFIG_SPI_FLASH=y
 CONFIG_SPI_FLASH_STMICRO=y
 CONFIG_SPI_FLASH_WINBOND=y
diff --git a/include/configs/omapl138_lcdk.h b/include/configs/omapl138_lcdk.h
index 5a6e7632b49..fd88f122ae9 100644
--- a/include/configs/omapl138_lcdk.h
+++ b/include/configs/omapl138_lcdk.h
@@ -172,6 +172,33 @@
 #define CONFIG_SYS_NAND_MASK_ALE	0x8
 #undef CONFIG_SYS_NAND_HW_ECC
 #define CONFIG_SYS_MAX_NAND_DEVICE	1 /* Max number of NAND devices */
+#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_SIZE	(2 << 10)
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	0x200 /*0x60000*/
+#define CONFIG_SYS_NAND_U_BOOT_DST	0xc1080000
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST
+#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP	(CONFIG_SYS_NAND_U_BOOT_DST - \
+					CONFIG_SYS_NAND_U_BOOT_SIZE - \
+					CONFIG_SYS_MALLOC_LEN -       \
+					GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_NAND_ECCPOS		{				\
+				24, 25, 26, 27, 28, \
+				29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \
+				39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \
+				49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \
+				59, 60, 61, 62, 63 }
+#define CONFIG_SYS_NAND_PAGE_COUNT	64
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS	0
+#define CONFIG_SYS_NAND_ECCSIZE		512
+#define CONFIG_SYS_NAND_ECCBYTES	10
+#define CONFIG_SYS_NAND_OOBSIZE		64
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_NAND_SIMPLE
+#define CONFIG_SPL_NAND_LOAD
 #endif
 
 #ifdef CONFIG_SYS_USE_NOR