mirror of
https://github.com/u-boot/u-boot.git
synced 2024-11-28 07:03:31 +08:00
arm: Remove openrd boards
These boards have not been converted to generic board by the deadline. Remove them. Signed-off-by: Simon Glass <sjg@chromium.org>
This commit is contained in:
Simon Glass
Tom Rini
parent
93b25c0813
commit
7a2c1b13d7
@ -4,9 +4,6 @@ choice
|
||||
prompt "Marvell Kirkwood board select"
|
||||
optional
|
||||
|
||||
config TARGET_OPENRD
|
||||
bool "Marvell OpenRD Board"
|
||||
|
||||
config TARGET_RD6281A
|
||||
bool "RD6281A Board"
|
||||
|
||||
@ -63,7 +60,6 @@ endchoice
|
||||
config SYS_SOC
|
||||
default "kirkwood"
|
||||
|
||||
source "board/Marvell/openrd/Kconfig"
|
||||
source "board/Marvell/rd6281a/Kconfig"
|
||||
source "board/Marvell/dreamplug/Kconfig"
|
||||
source "board/Marvell/guruplug/Kconfig"
|
||||
|
||||
@ -1,12 +0,0 @@
|
||||
if TARGET_OPENRD
|
||||
|
||||
config SYS_BOARD
|
||||
default "openrd"
|
||||
|
||||
config SYS_VENDOR
|
||||
default "Marvell"
|
||||
|
||||
config SYS_CONFIG_NAME
|
||||
default "openrd"
|
||||
|
||||
endif
|
||||
@ -1,12 +0,0 @@
|
||||
OPENRD BOARD
|
||||
M: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
S: Maintained
|
||||
F: board/Marvell/openrd/
|
||||
F: include/configs/openrd.h
|
||||
F: configs/openrd_base_defconfig
|
||||
|
||||
OPENRD_CLIENT BOARD
|
||||
#M: -
|
||||
S: Maintained
|
||||
F: configs/openrd_client_defconfig
|
||||
F: configs/openrd_ultimate_defconfig
|
||||
@ -1,14 +0,0 @@
|
||||
#
|
||||
# (C) Copyright 2009
|
||||
# Net Insight <www.netinsight.net>
|
||||
# Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
|
||||
#
|
||||
# Based on sheevaplug:
|
||||
# (C) Copyright 2009
|
||||
# Marvell Semiconductor <www.marvell.com>
|
||||
# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
#
|
||||
# SPDX-License-Identifier: GPL-2.0+
|
||||
#
|
||||
|
||||
obj-y := openrd.o
|
||||
@ -1,152 +0,0 @@
|
||||
#
|
||||
# (C) Copyright 2009
|
||||
# Marvell Semiconductor <www.marvell.com>
|
||||
# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
#
|
||||
# SPDX-License-Identifier: GPL-2.0+
|
||||
#
|
||||
# Refer doc/README.kwbimage for more details about how-to configure
|
||||
# and create kirkwood boot image
|
||||
#
|
||||
|
||||
# Boot Media configurations
|
||||
BOOT_FROM nand
|
||||
NAND_ECC_MODE default
|
||||
NAND_PAGE_SIZE 0x0800
|
||||
|
||||
# SOC registers configuration using bootrom header extension
|
||||
# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
|
||||
|
||||
# Configure RGMII-0 interface pad voltage to 1.8V
|
||||
DATA 0xFFD100e0 0x1b1b1b9b
|
||||
|
||||
#Dram initalization for SINGLE x16 CL=5 @ 400MHz
|
||||
DATA 0xFFD01400 0x43000c30 # DDR Configuration register
|
||||
# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
|
||||
# bit23-14: zero
|
||||
# bit24: 1= enable exit self refresh mode on DDR access
|
||||
# bit25: 1 required
|
||||
# bit29-26: zero
|
||||
# bit31-30: 01
|
||||
|
||||
DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
|
||||
# bit 4: 0=addr/cmd in smame cycle
|
||||
# bit 5: 0=clk is driven during self refresh, we don't care for APX
|
||||
# bit 6: 0=use recommended falling edge of clk for addr/cmd
|
||||
# bit14: 0=input buffer always powered up
|
||||
# bit18: 1=cpu lock transaction enabled
|
||||
# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
|
||||
# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
|
||||
# bit30-28: 3 required
|
||||
# bit31: 0=no additional STARTBURST delay
|
||||
|
||||
DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
|
||||
# bit3-0: TRAS lsbs
|
||||
# bit7-4: TRCD
|
||||
# bit11- 8: TRP
|
||||
# bit15-12: TWR
|
||||
# bit19-16: TWTR
|
||||
# bit20: TRAS msb
|
||||
# bit23-21: 0x0
|
||||
# bit27-24: TRRD
|
||||
# bit31-28: TRTP
|
||||
|
||||
DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
|
||||
# bit6-0: TRFC
|
||||
# bit8-7: TR2R
|
||||
# bit10-9: TR2W
|
||||
# bit12-11: TW2W
|
||||
# bit31-13: zero required
|
||||
|
||||
DATA 0xFFD01410 0x000000cc # DDR Address Control
|
||||
# bit1-0: 00, Cs0width=x8
|
||||
# bit3-2: 11, Cs0size=1Gb
|
||||
# bit5-4: 00, Cs1width=x8
|
||||
# bit7-6: 11, Cs1size=1Gb
|
||||
# bit9-8: 00, Cs2width=nonexistent
|
||||
# bit11-10: 00, Cs2size =nonexistent
|
||||
# bit13-12: 00, Cs3width=nonexistent
|
||||
# bit15-14: 00, Cs3size =nonexistent
|
||||
# bit16: 0, Cs0AddrSel
|
||||
# bit17: 0, Cs1AddrSel
|
||||
# bit18: 0, Cs2AddrSel
|
||||
# bit19: 0, Cs3AddrSel
|
||||
# bit31-20: 0 required
|
||||
|
||||
DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
|
||||
# bit0: 0, OpenPage enabled
|
||||
# bit31-1: 0 required
|
||||
|
||||
DATA 0xFFD01418 0x00000000 # DDR Operation
|
||||
# bit3-0: 0x0, DDR cmd
|
||||
# bit31-4: 0 required
|
||||
|
||||
DATA 0xFFD0141C 0x00000C52 # DDR Mode
|
||||
# bit2-0: 2, BurstLen=2 required
|
||||
# bit3: 0, BurstType=0 required
|
||||
# bit6-4: 4, CL=5
|
||||
# bit7: 0, TestMode=0 normal
|
||||
# bit8: 0, DLL reset=0 normal
|
||||
# bit11-9: 6, auto-precharge write recovery ????????????
|
||||
# bit12: 0, PD must be zero
|
||||
# bit31-13: 0 required
|
||||
|
||||
DATA 0xFFD01420 0x00000042 # DDR Extended Mode
|
||||
# bit0: 0, DDR DLL enabled
|
||||
# bit1: 1, DDR drive strength reduced
|
||||
# bit2: 0, DDR ODT control lsd (disabled)
|
||||
# bit5-3: 000, required
|
||||
# bit6: 1, DDR ODT control msb, (disabled)
|
||||
# bit9-7: 000, required
|
||||
# bit10: 0, differential DQS enabled
|
||||
# bit11: 0, required
|
||||
# bit12: 0, DDR output buffer enabled
|
||||
# bit31-13: 0 required
|
||||
|
||||
DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
|
||||
# bit2-0: 111, required
|
||||
# bit3 : 1 , MBUS Burst Chop disabled
|
||||
# bit6-4: 111, required
|
||||
# bit7 : 0
|
||||
# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
|
||||
# bit9 : 0 , no half clock cycle addition to dataout
|
||||
# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
|
||||
# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
|
||||
# bit15-12: 1111 required
|
||||
# bit31-16: 0 required
|
||||
|
||||
DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
|
||||
DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
|
||||
|
||||
DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
|
||||
DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
|
||||
# bit0: 1, Window enabled
|
||||
# bit1: 0, Write Protect disabled
|
||||
# bit3-2: 00, CS0 hit selected
|
||||
# bit23-4: ones, required
|
||||
# bit31-24: 0x0F, Size (i.e. 256MB)
|
||||
|
||||
DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
|
||||
DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
|
||||
|
||||
DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
|
||||
DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
|
||||
|
||||
DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
|
||||
# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
|
||||
# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
|
||||
# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
|
||||
# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
|
||||
DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
|
||||
|
||||
DATA 0xFFD0149C 0x0000E40f # CPU ODT Control
|
||||
# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
|
||||
# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
|
||||
# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
|
||||
# bit14: 1, M_STARTBURST_IN ODT: Enabled
|
||||
# bit15: 1, DDR IO ODT Unit: Use ODT block
|
||||
DATA 0xFFD01480 0x00000001 # DDR Initialization Control
|
||||
#bit0=1, enable DDR init upon this register write
|
||||
|
||||
# End of Header extension
|
||||
DATA 0x0 0x0
|
||||
@ -1,161 +0,0 @@
|
||||
/*
|
||||
* (C) Copyright 2009
|
||||
* Net Insight <www.netinsight.net>
|
||||
* Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
|
||||
*
|
||||
* Based on sheevaplug.c:
|
||||
* (C) Copyright 2009
|
||||
* Marvell Semiconductor <www.marvell.com>
|
||||
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <miiphy.h>
|
||||
#include <asm/arch/cpu.h>
|
||||
#include <asm/arch/soc.h>
|
||||
#include <asm/arch/mpp.h>
|
||||
#include "openrd.h"
|
||||
|
||||
DECLARE_GLOBAL_DATA_PTR;
|
||||
|
||||
int board_early_init_f(void)
|
||||
{
|
||||
/*
|
||||
* default gpio configuration
|
||||
* There are maximum 64 gpios controlled through 2 sets of registers
|
||||
* the below configuration configures mainly initial LED status
|
||||
*/
|
||||
mvebu_config_gpio(OPENRD_OE_VAL_LOW,
|
||||
OPENRD_OE_VAL_HIGH,
|
||||
OPENRD_OE_LOW, OPENRD_OE_HIGH);
|
||||
|
||||
/* Multi-Purpose Pins Functionality configuration */
|
||||
static const u32 kwmpp_config[] = {
|
||||
MPP0_NF_IO2,
|
||||
MPP1_NF_IO3,
|
||||
MPP2_NF_IO4,
|
||||
MPP3_NF_IO5,
|
||||
MPP4_NF_IO6,
|
||||
MPP5_NF_IO7,
|
||||
MPP6_SYSRST_OUTn,
|
||||
MPP7_GPO,
|
||||
MPP8_TW_SDA,
|
||||
MPP9_TW_SCK,
|
||||
MPP10_UART0_TXD,
|
||||
MPP11_UART0_RXD,
|
||||
MPP12_SD_CLK,
|
||||
MPP13_SD_CMD, /* Alt UART1_TXD */
|
||||
MPP14_SD_D0, /* Alt UART1_RXD */
|
||||
MPP15_SD_D1,
|
||||
MPP16_SD_D2,
|
||||
MPP17_SD_D3,
|
||||
MPP18_NF_IO0,
|
||||
MPP19_NF_IO1,
|
||||
MPP20_GE1_0,
|
||||
MPP21_GE1_1,
|
||||
MPP22_GE1_2,
|
||||
MPP23_GE1_3,
|
||||
MPP24_GE1_4,
|
||||
MPP25_GE1_5,
|
||||
MPP26_GE1_6,
|
||||
MPP27_GE1_7,
|
||||
MPP28_GPIO,
|
||||
MPP29_TSMP9,
|
||||
MPP30_GE1_10,
|
||||
MPP31_GE1_11,
|
||||
MPP32_GE1_12,
|
||||
MPP33_GE1_13,
|
||||
MPP34_GPIO, /* UART1 / SD sel */
|
||||
MPP35_TDM_CH0_TX_QL,
|
||||
MPP36_TDM_SPI_CS1,
|
||||
MPP37_TDM_CH2_TX_QL,
|
||||
MPP38_TDM_CH2_RX_QL,
|
||||
MPP39_AUDIO_I2SBCLK,
|
||||
MPP40_AUDIO_I2SDO,
|
||||
MPP41_AUDIO_I2SLRC,
|
||||
MPP42_AUDIO_I2SMCLK,
|
||||
MPP43_AUDIO_I2SDI,
|
||||
MPP44_AUDIO_EXTCLK,
|
||||
MPP45_TDM_PCLK,
|
||||
MPP46_TDM_FS,
|
||||
MPP47_TDM_DRX,
|
||||
MPP48_TDM_DTX,
|
||||
MPP49_TDM_CH0_RX_QL,
|
||||
0
|
||||
};
|
||||
|
||||
kirkwood_mpp_conf(kwmpp_config, NULL);
|
||||
return 0;
|
||||
}
|
||||
|
||||
int board_init(void)
|
||||
{
|
||||
/*
|
||||
* arch number of board
|
||||
*/
|
||||
#if defined(CONFIG_BOARD_IS_OPENRD_BASE)
|
||||
gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
|
||||
#elif defined(CONFIG_BOARD_IS_OPENRD_CLIENT)
|
||||
gd->bd->bi_arch_number = MACH_TYPE_OPENRD_CLIENT;
|
||||
#elif defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE)
|
||||
gd->bd->bi_arch_number = MACH_TYPE_OPENRD_ULTIMATE;
|
||||
#endif
|
||||
|
||||
/* adress of boot parameters */
|
||||
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
||||
return 0;
|
||||
}
|
||||
|
||||
#ifdef CONFIG_RESET_PHY_R
|
||||
/* Configure and enable MV88E1116/88E1121 PHY */
|
||||
void mv_phy_init(char *name)
|
||||
{
|
||||
u16 reg;
|
||||
u16 devadr;
|
||||
|
||||
if (miiphy_set_current_dev(name))
|
||||
return;
|
||||
|
||||
/* command to read PHY dev address */
|
||||
if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
|
||||
printf("Err..%s could not read PHY dev address\n",
|
||||
__FUNCTION__);
|
||||
return;
|
||||
}
|
||||
|
||||
/*
|
||||
* Enable RGMII delay on Tx and Rx for CPU port
|
||||
* Ref: sec 4.7.2 of chip datasheet
|
||||
*/
|
||||
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
|
||||
miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
|
||||
reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
|
||||
miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
|
||||
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
|
||||
|
||||
/* reset the phy */
|
||||
miiphy_reset(name, devadr);
|
||||
|
||||
printf(PHY_NO" Initialized on %s\n", name);
|
||||
}
|
||||
|
||||
void reset_phy(void)
|
||||
{
|
||||
mv_phy_init("egiga0");
|
||||
|
||||
#ifdef CONFIG_BOARD_IS_OPENRD_CLIENT
|
||||
/* Kirkwood ethernet driver is written with the assumption that in case
|
||||
* of multiple PHYs, their addresses are consecutive. But unfortunately
|
||||
* in case of OpenRD-Client, PHY addresses are not consecutive.*/
|
||||
miiphy_write("egiga1", 0xEE, 0xEE, 24);
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_BOARD_IS_OPENRD_CLIENT) || \
|
||||
defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE)
|
||||
/* configure and initialize both PHY's */
|
||||
mv_phy_init("egiga1");
|
||||
#endif
|
||||
}
|
||||
#endif /* CONFIG_RESET_PHY_R */
|
||||
@ -1,30 +0,0 @@
|
||||
/*
|
||||
* (C) Copyright 2009
|
||||
* Net Insight <www.netinsight.net>
|
||||
* Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
|
||||
*
|
||||
* Based on sheevaplug.h:
|
||||
* (C) Copyright 2009
|
||||
* Marvell Semiconductor <www.marvell.com>
|
||||
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#ifndef __OPENRD_BASE_H
|
||||
#define __OPENRD_BASE_H
|
||||
|
||||
#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */
|
||||
#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */
|
||||
#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */
|
||||
#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */
|
||||
|
||||
/* PHY related */
|
||||
#define MV88E1116_LED_FCTRL_REG 10
|
||||
#define MV88E1116_CPRSP_CR3_REG 21
|
||||
#define MV88E1116_MAC_CTRL_REG 21
|
||||
#define MV88E1116_PGADR_REG 22
|
||||
#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
|
||||
#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
|
||||
|
||||
#endif /* __OPENRD_BASE_H */
|
||||
@ -1,7 +0,0 @@
|
||||
CONFIG_ARM=y
|
||||
CONFIG_KIRKWOOD=y
|
||||
CONFIG_TARGET_OPENRD=y
|
||||
CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_BASE"
|
||||
# CONFIG_CMD_IMLS is not set
|
||||
# CONFIG_CMD_FLASH is not set
|
||||
# CONFIG_CMD_SETEXPR is not set
|
||||
@ -1,7 +0,0 @@
|
||||
CONFIG_ARM=y
|
||||
CONFIG_KIRKWOOD=y
|
||||
CONFIG_TARGET_OPENRD=y
|
||||
CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_CLIENT"
|
||||
# CONFIG_CMD_IMLS is not set
|
||||
# CONFIG_CMD_FLASH is not set
|
||||
# CONFIG_CMD_SETEXPR is not set
|
||||
@ -1,7 +0,0 @@
|
||||
CONFIG_ARM=y
|
||||
CONFIG_KIRKWOOD=y
|
||||
CONFIG_TARGET_OPENRD=y
|
||||
CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_ULTIMATE"
|
||||
# CONFIG_CMD_IMLS is not set
|
||||
# CONFIG_CMD_FLASH is not set
|
||||
# CONFIG_CMD_SETEXPR is not set
|
||||
@ -1,137 +0,0 @@
|
||||
/*
|
||||
* (C) Copyright 2009
|
||||
* Net Insight <www.netinsight.net>
|
||||
* Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
|
||||
*
|
||||
* Based on sheevaplug.h:
|
||||
* (C) Copyright 2009
|
||||
* Marvell Semiconductor <www.marvell.com>
|
||||
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#ifndef _CONFIG_OPENRD_H
|
||||
#define _CONFIG_OPENRD_H
|
||||
|
||||
/*
|
||||
* Version number information
|
||||
*/
|
||||
#ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE
|
||||
# define CONFIG_IDENT_STRING "\nOpenRD-Ultimate"
|
||||
#else
|
||||
# ifdef CONFIG_BOARD_IS_OPENRD_CLIENT
|
||||
# define CONFIG_IDENT_STRING "\nOpenRD-Client"
|
||||
# else
|
||||
# ifdef CONFIG_BOARD_IS_OPENRD_BASE
|
||||
# define CONFIG_IDENT_STRING "\nOpenRD-Base"
|
||||
# else
|
||||
# error Unknown OpenRD board specified
|
||||
# endif
|
||||
# endif
|
||||
#endif
|
||||
|
||||
/*
|
||||
* High Level Configuration Options (easy to change)
|
||||
*/
|
||||
#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */
|
||||
#define CONFIG_KW88F6281 1 /* SOC Name */
|
||||
#define CONFIG_MACH_OPENRD_BASE /* Machine type */
|
||||
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
|
||||
|
||||
/*
|
||||
* Commands configuration
|
||||
*/
|
||||
#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
|
||||
#define CONFIG_SYS_MVFS
|
||||
#define CONFIG_CMD_DHCP
|
||||
#define CONFIG_CMD_ENV
|
||||
#define CONFIG_CMD_MII
|
||||
#define CONFIG_CMD_MMC
|
||||
#define CONFIG_CMD_NAND
|
||||
#define CONFIG_CMD_PING
|
||||
#define CONFIG_CMD_USB
|
||||
#define CONFIG_CMD_IDE
|
||||
|
||||
/*
|
||||
* mv-common.h should be defined after CMD configs since it used them
|
||||
* to enable certain macros
|
||||
*/
|
||||
#include "mv-common.h"
|
||||
|
||||
/*
|
||||
* Environment variables configurations
|
||||
*/
|
||||
#ifdef CONFIG_CMD_NAND
|
||||
#define CONFIG_ENV_IS_IN_NAND 1
|
||||
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
|
||||
#else
|
||||
#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
|
||||
#endif
|
||||
/*
|
||||
* max 4k env size is enough, but in case of nand
|
||||
* it has to be rounded to sector size
|
||||
*/
|
||||
#define CONFIG_ENV_SIZE 0x20000 /* 128k */
|
||||
#define CONFIG_ENV_ADDR 0x60000
|
||||
#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */
|
||||
/*
|
||||
* Environment is right behind U-Boot in flash. Make sure U-Boot
|
||||
* doesn't grow into the environment area.
|
||||
*/
|
||||
#define CONFIG_BOARD_SIZE_LIMIT CONFIG_ENV_OFFSET
|
||||
|
||||
/*
|
||||
* Default environment variables
|
||||
*/
|
||||
#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
|
||||
"setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
|
||||
"${x_bootcmd_usb}; bootm 0x6400000;"
|
||||
|
||||
#define MTDIDS_DEFAULT "nand0=nand_mtd"
|
||||
#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000@0x000000(uboot),"\
|
||||
"0x400000@0x100000(uImage),"\
|
||||
"0x1fb00000@0x500000(rootfs)"
|
||||
|
||||
#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
|
||||
"=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
|
||||
"x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
|
||||
"x_bootcmd_usb=usb start\0" \
|
||||
"x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \
|
||||
"mtdids="MTDIDS_DEFAULT"\0" \
|
||||
"mtdparts="MTDPARTS_DEFAULT"\0"
|
||||
|
||||
/*
|
||||
* Ethernet Driver configuration
|
||||
*/
|
||||
#ifdef CONFIG_CMD_NET
|
||||
# ifdef CONFIG_BOARD_IS_OPENRD_BASE
|
||||
# define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
|
||||
# else
|
||||
# define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */
|
||||
# endif
|
||||
# ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE
|
||||
# define CONFIG_PHY_BASE_ADR 0x0
|
||||
# define PHY_NO "88E1121"
|
||||
# else
|
||||
# define CONFIG_PHY_BASE_ADR 0x8
|
||||
# define PHY_NO "88E1116"
|
||||
# endif
|
||||
#endif /* CONFIG_CMD_NET */
|
||||
|
||||
/*
|
||||
* SATA Driver configuration
|
||||
*/
|
||||
#ifdef CONFIG_MVSATA_IDE
|
||||
#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
|
||||
#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
|
||||
#endif /*CONFIG_MVSATA_IDE*/
|
||||
|
||||
#ifdef CONFIG_CMD_MMC
|
||||
#define CONFIG_MMC
|
||||
#define CONFIG_GENERIC_MMC
|
||||
#define CONFIG_MVEBU_MMC
|
||||
#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE
|
||||
#endif /* CONFIG_CMD_MMC */
|
||||
|
||||
#endif /* _CONFIG_OPENRD_BASE_H */
|
||||
Loading…
Reference in New Issue
Block a user