From 316ab801c0d91c02b21b8be1e3db7e69555364e9 Mon Sep 17 00:00:00 2001 From: Ilias Apalodimas Date: Sat, 17 Jul 2021 17:26:46 +0300 Subject: [PATCH] doc: Update CapsuleUpdate READMEs Since we removed embeddingg the capsule key into a .dtb and fixed authenticated capsule updates for all boards, move the relevant documentation in the efi file and update it accordingly Signed-off-by: Ilias Apalodimas --- doc/board/emulation/qemu_capsule_update.rst | 203 -------------------- doc/develop/uefi/uefi.rst | 125 ++++++++++++ 2 files changed, 125 insertions(+), 203 deletions(-) delete mode 100644 doc/board/emulation/qemu_capsule_update.rst diff --git a/doc/board/emulation/qemu_capsule_update.rst b/doc/board/emulation/qemu_capsule_update.rst deleted file mode 100644 index 0a2286d039d..00000000000 --- a/doc/board/emulation/qemu_capsule_update.rst +++ /dev/null @@ -1,203 +0,0 @@ -.. SPDX-License-Identifier: GPL-2.0+ -.. Copyright (C) 2020, Linaro Limited - -Enabling UEFI Capsule Update feature ------------------------------------- - -Support has been added for the UEFI capsule update feature which -enables updating the U-Boot image using the UEFI firmware management -protocol (fmp). The capsules are not passed to the firmware through -the UpdateCapsule runtime service. Instead, capsule-on-disk -functionality is used for fetching the capsule from the EFI System -Partition (ESP) by placing the capsule file under the -\EFI\UpdateCapsule directory. - -Currently, support has been added on the QEMU ARM64 virt platform for -updating the U-Boot binary as a raw image when the platform is booted -in non-secure mode, i.e. with CONFIG_TFABOOT disabled. For this -configuration, the QEMU platform needs to be booted with -'secure=off'. The U-Boot binary placed on the first bank of the NOR -flash at offset 0x0. The U-Boot environment is placed on the second -NOR flash bank at offset 0x4000000. - -The capsule update feature is enabled with the following configuration -settings:: - - CONFIG_MTD=y - CONFIG_FLASH_CFI_MTD=y - CONFIG_CMD_MTDPARTS=y - CONFIG_CMD_DFU=y - CONFIG_DFU_MTD=y - CONFIG_PCI_INIT_R=y - CONFIG_EFI_CAPSULE_ON_DISK=y - CONFIG_EFI_CAPSULE_FIRMWARE_MANAGEMENT=y - CONFIG_EFI_CAPSULE_FIRMWARE=y - CONFIG_EFI_CAPSULE_FIRMWARE_RAW=y - CONFIG_EFI_CAPSULE_FMP_HEADER=y - -In addition, the following config needs to be disabled(QEMU ARM specific):: - - CONFIG_TFABOOT - -The capsule file can be generated by using the tools/mkeficapsule:: - - $ mkeficapsule --raw --index 1 - -As per the UEFI specification, the capsule file needs to be placed on -the EFI System Partition, under the \EFI\UpdateCapsule directory. The -EFI System Partition can be a virtio-blk-device. - -Before initiating the firmware update, the efi variables BootNext, -BootXXXX and OsIndications need to be set. The BootXXXX variable needs -to be pointing to the EFI System Partition which contains the capsule -file. The BootNext, BootXXXX and OsIndications variables can be set -using the following commands:: - - => efidebug boot add -b 0 Boot0000 virtio 0:1 - => efidebug boot next 0 - => setenv -e -nv -bs -rt -v OsIndications =0x04 - => saveenv - -Finally, the capsule update can be initiated with the following -command:: - - => efidebug capsule disk-update - -The updated U-Boot image will be booted on subsequent boot. - -Enabling Capsule Authentication -^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ - -The UEFI specification defines a way of authenticating the capsule to -be updated by verifying the capsule signature. The capsule signature -is computed and prepended to the capsule payload at the time of -capsule generation. This signature is then verified by using the -public key stored as part of the X509 certificate. This certificate is -in the form of an efi signature list (esl) file, which is embedded as -part of the platform's device tree blob using the mkeficapsule -utility. - -On the QEMU virt platforms, the device-tree is generated on the fly -based on the devices configured. This device tree is then passed on to -the various software components booting on the platform, including -U-Boot. Therefore, on the QEMU virt platform, the signatute is -embedded on an overlay. This overlay is then applied at runtime to the -base platform device-tree. Steps needed for embedding the esl file in -the overlay are highlighted below. - -The capsule authentication feature can be enabled through the -following config, in addition to the configs listed above for capsule -update:: - - CONFIG_EFI_CAPSULE_AUTHENTICATE=y - -The public and private keys used for the signing process are generated -and used by the steps highlighted below:: - - 1. Install utility commands on your host - * OPENSSL - * efitools - - 2. Create signing keys and certificate files on your host - - $ openssl req -x509 -sha256 -newkey rsa:2048 -subj /CN=CRT/ \ - -keyout CRT.key -out CRT.crt -nodes -days 365 - $ cert-to-efi-sig-list CRT.crt CRT.esl - - $ openssl x509 -in CRT.crt -out CRT.cer -outform DER - $ openssl x509 -inform DER -in CRT.cer -outform PEM -out CRT.pub.pem - - $ openssl pkcs12 -export -out CRT.pfx -inkey CRT.key -in CRT.crt - $ openssl pkcs12 -in CRT.pfx -nodes -out CRT.pem - -The capsule file can be generated by using the GenerateCapsule.py -script in EDKII:: - - $ ./BaseTools/BinWrappers/PosixLike/GenerateCapsule -e -o \ - --monotonic-count --fw-version \ - --lsv --guid \ - e2bb9c06-70e9-4b14-97a3-5a7913176e3f --verbose \ - --update-image-index --signer-private-cert \ - /path/to/CRT.pem --trusted-public-cert \ - /path/to/CRT.pub.pem --other-public-cert /path/to/CRT.pub.pem \ - - -Place the capsule generated in the above step on the EFI System -Partition under the EFI/UpdateCapsule directory - -For embedding the public key certificate, the following steps need to -be followed:: - - 1. Generate a skeleton overlay dts file, with a single fragment - node and an empty __overlay__ node - - A typical skeleton overlay file will look like this - - /dts-v1/; - /plugin/; - - / { - fragment@0 { - target-path = "/"; - __overlay__ { - }; - }; - }; - - - 2. Convert the dts to a corresponding dtb with the following - command - ./scripts/dtc/dtc -@ -I dts -O dtb -o \ - - - 3. Run the dtb file generated above through the mkeficapsule tool - in U-Boot - ./tools/mkeficapsule -O -D - -Running the above command results in the creation of a 'signature' -node in the dtb, under which the public key is stored as a -'capsule-key' property. The '-O' option is to be used since the -public key certificate(esl) file is being embedded in an overlay. - -The dtb file embedded with the certificate is now to be placed on an -EFI System Partition. This would then be loaded and "merged" with the -base platform flattened device-tree(dtb) at runtime. - -Build U-Boot with the following steps(QEMU ARM64):: - - $ make qemu_arm64_defconfig - $ make menuconfig - Disable CONFIG_TFABOOT - Enable CONFIG_EFI_CAPSULE_AUTHENTICATE - Enable all configs needed for capsule update(listed above) - $ make all - -Boot the platform and perform the following steps on the U-Boot -command line:: - - 1. Enable capsule authentication by setting the following env - variable - - => setenv capsule_authentication_enabled 1 - => saveenv - - 2. Load the overlay dtb to memory and merge it with the base fdt - - => fatload virtio 0:1 <$fdtovaddr> EFI/ - => fdt addr $fdtcontroladdr - => fdt resize - => fdt apply <$fdtovaddr> - - 3. Set the following environment and UEFI boot variables - - => setenv -e -nv -bs -rt -v OsIndications =0x04 - => efidebug boot add -b 0 Boot0000 virtio 0:1 - => efidebug boot next 0 - => saveenv - - 4. Finally, the capsule update can be initiated with the following - command - - => efidebug capsule disk-update - -On subsequent reboot, the platform should boot the updated U-Boot binary. diff --git a/doc/develop/uefi/uefi.rst b/doc/develop/uefi/uefi.rst index 4f2b8b036db..64fe9346c7f 100644 --- a/doc/develop/uefi/uefi.rst +++ b/doc/develop/uefi/uefi.rst @@ -277,6 +277,131 @@ Enable ``CONFIG_OPTEE``, ``CONFIG_CMD_OPTEE_RPMB`` and ``CONFIG_EFI_MM_COMM_TEE` [1] https://optee.readthedocs.io/en/latest/building/efi_vars/stmm.html +Enabling UEFI Capsule Update feature +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Support has been added for the UEFI capsule update feature which +enables updating the U-Boot image using the UEFI firmware management +protocol (FMP). The capsules are not passed to the firmware through +the UpdateCapsule runtime service. Instead, capsule-on-disk +functionality is used for fetching the capsule from the EFI System +Partition (ESP) by placing the capsule file under the +\EFI\UpdateCapsule directory. + +The directory \EFI\UpdateCapsule is checked for capsules only within the +EFI system partition on the device specified in the active boot option +determined by reference to BootNext variable or BootOrder variable processing. +The active Boot Variable is the variable with highest priority BootNext or +within BootOrder that refers to a device found to be present. Boot variables +in BootOrder but referring to devices not present are ignored when determining +active boot variable. +Before starting a capsule update make sure your capsules are installed in the +correct ESP partition or set BootNext. + +Performing the update +********************* + +Since U-boot doesn't currently support SetVariable at runtime there's a Kconfig +option (CONFIG_EFI_IGNORE_OSINDICATIONS) to disable the OsIndications variable +check. If that option is enabled just copy your capsule to \EFI\UpdateCapsule. + +If that option is disabled, you'll need to set the OsIndications variable with:: + + => setenv -e -nv -bs -rt -v OsIndications =0x04 + +Finally, the capsule update can be initiated either by rebooting the board, +which is the preferred method, or by issuing the following command:: + + => efidebug capsule disk-update + +**The efidebug command is should only be used during debugging/development.** + +Enabling Capsule Authentication +******************************* + +The UEFI specification defines a way of authenticating the capsule to +be updated by verifying the capsule signature. The capsule signature +is computed and prepended to the capsule payload at the time of +capsule generation. This signature is then verified by using the +public key stored as part of the X509 certificate. This certificate is +in the form of an efi signature list (esl) file, which is embedded as +part of U-Boot. + +The capsule authentication feature can be enabled through the +following config, in addition to the configs listed above for capsule +update:: + + CONFIG_EFI_CAPSULE_AUTHENTICATE=y + CONFIG_EFI_CAPSULE_KEY_PATH= + +The public and private keys used for the signing process are generated +and used by the steps highlighted below:: + + 1. Install utility commands on your host + * OPENSSL + * efitools + + 2. Create signing keys and certificate files on your host + + $ openssl req -x509 -sha256 -newkey rsa:2048 -subj /CN=CRT/ \ + -keyout CRT.key -out CRT.crt -nodes -days 365 + $ cert-to-efi-sig-list CRT.crt CRT.esl + + $ openssl x509 -in CRT.crt -out CRT.cer -outform DER + $ openssl x509 -inform DER -in CRT.cer -outform PEM -out CRT.pub.pem + + $ openssl pkcs12 -export -out CRT.pfx -inkey CRT.key -in CRT.crt + $ openssl pkcs12 -in CRT.pfx -nodes -out CRT.pem + +The capsule file can be generated by using the GenerateCapsule.py +script in EDKII:: + + $ ./BaseTools/BinWrappers/PosixLike/GenerateCapsule -e -o \ + --monotonic-count --fw-version \ + --lsv --guid \ + e2bb9c06-70e9-4b14-97a3-5a7913176e3f --verbose \ + --update-image-index --signer-private-cert \ + /path/to/CRT.pem --trusted-public-cert \ + /path/to/CRT.pub.pem --other-public-cert /path/to/CRT.pub.pem \ + + +Place the capsule generated in the above step on the EFI System +Partition under the EFI/UpdateCapsule directory + +Testing on QEMU +*************** + +Currently, support has been added on the QEMU ARM64 virt platform for +updating the U-Boot binary as a raw image when the platform is booted +in non-secure mode, i.e. with CONFIG_TFABOOT disabled. For this +configuration, the QEMU platform needs to be booted with +'secure=off'. The U-Boot binary placed on the first bank of the NOR +flash at offset 0x0. The U-Boot environment is placed on the second +NOR flash bank at offset 0x4000000. + +The capsule update feature is enabled with the following configuration +settings:: + + CONFIG_MTD=y + CONFIG_FLASH_CFI_MTD=y + CONFIG_CMD_MTDPARTS=y + CONFIG_CMD_DFU=y + CONFIG_DFU_MTD=y + CONFIG_PCI_INIT_R=y + CONFIG_EFI_CAPSULE_ON_DISK=y + CONFIG_EFI_CAPSULE_FIRMWARE_MANAGEMENT=y + CONFIG_EFI_CAPSULE_FIRMWARE=y + CONFIG_EFI_CAPSULE_FIRMWARE_RAW=y + CONFIG_EFI_CAPSULE_FMP_HEADER=y + +In addition, the following config needs to be disabled(QEMU ARM specific):: + + CONFIG_TFABOOT + +The capsule file can be generated by using the tools/mkeficapsule:: + + $ mkeficapsule --raw --index 1 + Executing the boot manager ~~~~~~~~~~~~~~~~~~~~~~~~~~