mirror of
https://github.com/u-boot/u-boot.git
synced 2024-11-26 13:44:29 +08:00
TI OMAP3 Use arm init sequence to initialize i2c
This changes fixes an early i2c error. It appears that I2C is working because once a read or write error is detected, the omap24xx_i2c driver calls i2c_init inside its error handling check. While it is ok to attempt error handling this way, the boards must not depend on this side effect to initialize it's i2c. Instead of explicitly calling i2c_init for every board, use the generic arm initialization in lib_arm/board.c. By defining the config variable CONFIG_HARD_I2C, the omap3 i2c initialization is included in the init_sequence table. Run tested on Beagle. Compile tested on the omap3's Signed-off-by: Tom Rix <Tom.Rix@windriver.com> Acked-by: Dirk Behme <dirk.behme@googlemail.com>
This commit is contained in:
parent
4df30f3bb7
commit
0297ec7e2a
@ -98,6 +98,7 @@
|
||||
#define CONFIG_DOS_PARTITION 1
|
||||
|
||||
/* I2C */
|
||||
#define CONFIG_HARD_I2C 1
|
||||
#define CONFIG_SYS_I2C_SPEED 100000
|
||||
#define CONFIG_SYS_I2C_SLAVE 1
|
||||
#define CONFIG_SYS_I2C_BUS 0
|
||||
|
@ -123,6 +123,7 @@
|
||||
#undef CONFIG_CMD_NFS /* NFS support */
|
||||
|
||||
#define CONFIG_SYS_NO_FLASH
|
||||
#define CONFIG_HARD_I2C 1
|
||||
#define CONFIG_SYS_I2C_SPEED 100000
|
||||
#define CONFIG_SYS_I2C_SLAVE 1
|
||||
#define CONFIG_SYS_I2C_BUS 0
|
||||
|
@ -121,6 +121,7 @@
|
||||
#undef CONFIG_CMD_IMLS /* List all found images */
|
||||
|
||||
#define CONFIG_SYS_NO_FLASH
|
||||
#define CONFIG_HARD_I2C 1
|
||||
#define CONFIG_SYS_I2C_SPEED 100000
|
||||
#define CONFIG_SYS_I2C_SLAVE 1
|
||||
#define CONFIG_SYS_I2C_BUS 0
|
||||
|
@ -109,6 +109,7 @@
|
||||
#undef CONFIG_CMD_NFS /* NFS support */
|
||||
|
||||
#define CONFIG_SYS_NO_FLASH
|
||||
#define CONFIG_HARD_I2C 1
|
||||
#define CONFIG_SYS_I2C_SPEED 100000
|
||||
#define CONFIG_SYS_I2C_SLAVE 1
|
||||
#define CONFIG_SYS_I2C_BUS 0
|
||||
|
@ -112,6 +112,7 @@
|
||||
#undef CONFIG_CMD_NFS /* NFS support */
|
||||
|
||||
#define CONFIG_SYS_NO_FLASH
|
||||
#define CONFIG_HARD_I2C 1
|
||||
#define CONFIG_SYS_I2C_SPEED 100000
|
||||
#define CONFIG_SYS_I2C_SLAVE 1
|
||||
#define CONFIG_SYS_I2C_BUS 0
|
||||
|
@ -119,6 +119,7 @@
|
||||
#undef CONFIG_CMD_NFS /* NFS support */
|
||||
|
||||
#define CONFIG_SYS_NO_FLASH
|
||||
#define CONFIG_HARD_I2C 1
|
||||
#define CONFIG_SYS_I2C_SPEED 100000
|
||||
#define CONFIG_SYS_I2C_SLAVE 1
|
||||
#define CONFIG_SYS_I2C_BUS 0
|
||||
|
@ -140,6 +140,7 @@
|
||||
#undef CONFIG_CMD_NFS /* NFS support */
|
||||
|
||||
#define CONFIG_SYS_NO_FLASH
|
||||
#define CONFIG_HARD_I2C 1
|
||||
#define CONFIG_SYS_I2C_SPEED 100000
|
||||
#define CONFIG_SYS_I2C_SLAVE 1
|
||||
#define CONFIG_SYS_I2C_BUS 0
|
||||
|
Loading…
Reference in New Issue
Block a user