diff --git a/board/udoo/neo/neo.c b/board/udoo/neo/neo.c index 9e2a66996c4..1287f719197 100644 --- a/board/udoo/neo/neo.c +++ b/board/udoo/neo/neo.c @@ -43,10 +43,6 @@ enum { UDOO_NEO_TYPE_EXTENDED, }; -#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ - PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ - PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) - #define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) @@ -98,11 +94,6 @@ int power_init_board(void) return 0; } -static iomux_v3_cfg_t const uart1_pads[] = { - MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL), -}; - static iomux_v3_cfg_t const usdhc2_pads[] = { MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), @@ -130,11 +121,6 @@ static iomux_v3_cfg_t const peri_3v3_pads[] = { MX6_PAD_QSPI1A_DATA0__GPIO4_IO_16 | MUX_PAD_CTRL(NO_PAD_CTRL), }; -static void setup_iomux_uart(void) -{ - imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); -} - static int setup_fec(void) { struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; @@ -184,13 +170,6 @@ int board_init(void) return 0; } -int board_early_init_f(void) -{ - setup_iomux_uart(); - - return 0; -} - static struct fsl_esdhc_cfg usdhc_cfg[1] = { {USDHC2_BASE_ADDR}, }; @@ -421,11 +400,12 @@ void board_init_f(ulong dummy) /* setup AIPS and disable watchdog */ arch_cpu_init(); - board_early_init_f(); - /* setup GP timer */ timer_init(); + /* Enable device tree and early DM support*/ + spl_early_init(); + /* UART clocks enabled and gd valid - init serial console */ preloader_console_init(); diff --git a/configs/udoo_neo_defconfig b/configs/udoo_neo_defconfig index a450482b11d..73ab0f09f96 100644 --- a/configs/udoo_neo_defconfig +++ b/configs/udoo_neo_defconfig @@ -22,7 +22,6 @@ CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_DISTRO_DEFAULTS=y CONFIG_SYS_MONITOR_LEN=409600 CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd" -CONFIG_BOARD_EARLY_INIT_F=y CONFIG_SYS_SPL_MALLOC=y CONFIG_SPL_ENV_SUPPORT=y CONFIG_SPL_FS_EXT4=y @@ -60,6 +59,7 @@ CONFIG_DM_REGULATOR=y CONFIG_DM_REGULATOR_FIXED=y CONFIG_DM_REGULATOR_ANATOP=y CONFIG_DM_REGULATOR_PFUZE100=y +CONFIG_DM_SERIAL=y CONFIG_MXC_UART=y CONFIG_IMX_THERMAL=y CONFIG_USB=y