u-boot/configs/gt90h_v4_defconfig

CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_MACH_SUN8I_A23=y
CONFIG_DRAM_CLK=480
CONFIG_DRAM_ZQ=32767
CONFIG_MMC0_CD_PIN="PB4"
CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
CONFIG_USB0_ID_DET="PH8"
CONFIG_AXP_GPIO=y
CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:55000,le:159,ri:160,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
CONFIG_VIDEO_LCD_DCLK_PHASE=0
CONFIG_VIDEO_LCD_POWER="PH7"
CONFIG_VIDEO_LCD_BL_EN="PH6"
CONFIG_VIDEO_LCD_BL_PWM="PH0"
CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-gt90h-v4"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_AXP_DLDO1_VOLT=3300
CONFIG_USB_MUSB_HOST=y
sunxi: Add support for gt90h-v4 tablets The gt90h is a pcb found in generic 9" tablets with an A23 soc, 1G RAM and 8G nand, rtl8723as usb wifi, 1 micro usb port and 1 micro sd slot. The pmic setup on this board is somewhat special, dcdc2 MUST be set to 1.1V instead of the usual 1.2V otherwise the board is very unstable. aldo1 is used to power the micro sd slot, dldo1 is used for wifi. This commit adds a defconfig + dts (as submitted to the kernel) for the gt90h-v4 pcb. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2015-08-14 22:13:03 +08:00			`CONFIG_ARM=y`
			`CONFIG_ARCH_SUNXI=y`
			`CONFIG_MACH_SUN8I_A23=y`
			`CONFIG_DRAM_CLK=480`
			`CONFIG_DRAM_ZQ=32767`
			`CONFIG_MMC0_CD_PIN="PB4"`
			`CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"`
			`CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"`
			`CONFIG_USB0_ID_DET="PH8"`
			`CONFIG_AXP_GPIO=y`
			`CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:55000,le:159,ri:160,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"`
			`CONFIG_VIDEO_LCD_DCLK_PHASE=0`
			`CONFIG_VIDEO_LCD_POWER="PH7"`
			`CONFIG_VIDEO_LCD_BL_EN="PH6"`
			`CONFIG_VIDEO_LCD_BL_PWM="PH0"`
			`CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-gt90h-v4"`
			`# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set`
			`CONFIG_SPL=y`
			`CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"`
			`# CONFIG_CMD_IMLS is not set`
			`# CONFIG_CMD_FLASH is not set`
			`# CONFIG_CMD_FPGA is not set`
sunxi: power: Make all voltages configurable through Kconfig On boards with axp221/223 pmic-s we already allow configuring most voltages. Make the Kconfig options for these also apply to boards with axp152 / axp209 pmic-s and extend them to configure all voltages. The Kconfig defaults are chosen so that this commit does not introduce any functional changes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> 2015-09-30 21:22:42 +08:00			`CONFIG_AXP_DLDO1_VOLT=3300`
Reorder defconfigs with 'savedefconfig' Some boards' defconfigs are disordered. Reorder them. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> 2015-09-28 20:14:15 +08:00			`CONFIG_USB_MUSB_HOST=y`