u-boot/configs/orangepi_lite2_defconfig

CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
CONFIG_SPL=y
CONFIG_MACH_SUN50I_H6=y
CONFIG_SUNXI_DRAM_H6_LPDDR3=y
CONFIG_MMC0_CD_PIN="PF6"
# CONFIG_PSCI_RESET is not set
CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-orangepi-lite2"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_OHCI_HCD=y
board: allwinner: sun50i-h6: Add Orangepi Lite2 support OrangePi Lite2 is Allwinner H6 based open-source SBC, which support: - Allwinner H6 Quad-core 64-bit ARM Cortex-A53 - GPU Mali-T720 - 1GB LPDDR3 RAM - AXP805 PMIC - AP6356S Wifi/BT - USB 2.0, USB 3.0 Host, OTG - HDMI port - 5V/2A DC power supply Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> 2018-11-05 15:50:40 +08:00			`CONFIG_ARM=y`
			`CONFIG_ARCH_SUNXI=y`
			`CONFIG_SPL=y`
			`CONFIG_MACH_SUN50I_H6=y`
sunxi: H6: move LPDDR3 timing definition into separate file Currently the H6 DRAM driver only supports one kind of LPDDR3 DRAM. Split the timing parameters for this LPDDR3 configuration into a separate file, to allow selecting an alternative later at compile time (as the sunxi-dw driver does). Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> 2019-07-15 09:27:06 +08:00			`CONFIG_SUNXI_DRAM_H6_LPDDR3=y`
board: allwinner: sun50i-h6: Add Orangepi Lite2 support OrangePi Lite2 is Allwinner H6 based open-source SBC, which support: - Allwinner H6 Quad-core 64-bit ARM Cortex-A53 - GPU Mali-T720 - 1GB LPDDR3 RAM - AXP805 PMIC - AP6356S Wifi/BT - USB 2.0, USB 3.0 Host, OTG - HDMI port - 5V/2A DC power supply Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> 2018-11-05 15:50:40 +08:00			`CONFIG_MMC0_CD_PIN="PF6"`
			`# CONFIG_PSCI_RESET is not set`
			`CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-orangepi-lite2"`
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2020-07-28 20:46:52 +08:00			`# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set`
sunxi: H6: Enable USB for existing boards So far USB was not enabled for the Allwinner H6 boards, as the PHY driver was not ready and the clock gates were missing. Since this is now fixed, let's add the PHY and the OHCI/EHCI drivers to the build, for all existing H6 boards. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64 Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> 2019-06-23 22:09:50 +08:00			`CONFIG_USB_EHCI_HCD=y`
			`CONFIG_USB_OHCI_HCD=y`