u-boot/configs/qemu-riscv32_spl_defconfig

CONFIG_RISCV=y
CONFIG_ENV_SIZE=0x20000
CONFIG_NR_DRAM_BANKS=1
CONFIG_SPL=y
CONFIG_TARGET_QEMU_VIRT=y
CONFIG_RISCV_SMODE=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_FIT=y
CONFIG_DISPLAY_CPUINFO=y
CONFIG_DISPLAY_BOARDINFO=y
# CONFIG_CMD_MII is not set
CONFIG_OF_PRIOR_STAGE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM_MTD=y
riscv: qemu: add SPL configuration Add two new configurations (qemu-riscv{32,64}_spl_defconfig) with SPL enabled for RISC-V QEMU. QEMU does not require SPL to run U-Boot. The configurations are meant to help the development of SPL on RISC-V. The configurations enable RAM as the only SPL boot device. Images must be loaded at address 0x80200000. In the default boot flow, U-Boot SPL starts in machine mode, loads the OpenSBI FW_DYNAMIC firmware and U-Boot proper from the supplied FIT image, and starts OpenSBI. U-Boot proper is then started in supervisor mode by OpenSBI. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> 2019-08-22 03:14:49 +08:00			`CONFIG_RISCV=y`
env: Finish migration of common ENV options - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> 2019-11-19 09:02:10 +08:00			`CONFIG_ENV_SIZE=0x20000`
riscv: qemu: add SPL configuration Add two new configurations (qemu-riscv{32,64}_spl_defconfig) with SPL enabled for RISC-V QEMU. QEMU does not require SPL to run U-Boot. The configurations are meant to help the development of SPL on RISC-V. The configurations enable RAM as the only SPL boot device. Images must be loaded at address 0x80200000. In the default boot flow, U-Boot SPL starts in machine mode, loads the OpenSBI FW_DYNAMIC firmware and U-Boot proper from the supplied FIT image, and starts OpenSBI. U-Boot proper is then started in supervisor mode by OpenSBI. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> 2019-08-22 03:14:49 +08:00			`CONFIG_NR_DRAM_BANKS=1`
			`CONFIG_SPL=y`
			`CONFIG_TARGET_QEMU_VIRT=y`
			`CONFIG_RISCV_SMODE=y`
			`CONFIG_DISTRO_DEFAULTS=y`
			`CONFIG_FIT=y`
			`CONFIG_DISPLAY_CPUINFO=y`
			`CONFIG_DISPLAY_BOARDINFO=y`
			`# CONFIG_CMD_MII is not set`
			`CONFIG_OF_PRIOR_STAGE=y`
env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com> 2019-11-13 11:46:36 +08:00			`CONFIG_SYS_RELOC_GD_ENV_ADDR=y`
mtd: rename CONFIG_MTD -> CONFIG_DM_MTD CONFIG_MTD must be reserved for the MTD core. Like any other subsystem, prefix the symbol by DM when it comes to DM support. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> [trini: Add Kconfig files] Signed-off-by: Tom Rini <trini@konsulko.com> 2019-10-04 01:50:04 +08:00			`CONFIG_DM_MTD=y`