This can prevent bizarre failures if, for example, you've done a
configuration in the top-level source directory, leaving behind one
config.h file, and then do an out-of-tree build in another directory,
with different configuration options. This way, we always pick up the
same config.h, in the build directory.
Now all the macros have a name meaning a count in bytes.
With _S_: signed, _U_: unsigned
e.g.:
EXTRACT_BE_32BITS -> EXTRACT_BE_U_4
EXTRACT_LE_32BITS -> EXTRACT_LE_U_4
...
EXTRACT_BE_INT32 -> EXTRACT_BE_S_4
and have:
EXTRACT_8BITS -> EXTRACT_U_1
EXTRACT_INT8 -> EXTRACT_S_1
This fixes a buffer over-read discovered by Kamil Frankowicz.
Don't pass the remaining caplen - that's too hard to get right, and we
were getting it wrong in at least one case; just use ND_TTEST().
Add a test using the capture file supplied by the reporter(s).
The function sig_print() did receive a correct caplen parameter value
but didn't use it correctly and could overread by one byte as Brian
Carpenter has demonstrated. Fix it by switching to the standard macros.
with the tag '\summary:' for greping.
Remark: Currently some printers have no summary line.
Moreover:
Summarize all printers with a single line in INSTALL.txt
Have llc_print() return the length of the LLC header, plus the length of
the SNAP header, if available - or, if it couldn't dissect the payload,
return the *negative* of that sum. Use that return value in link-layer
printers.
Don't print LLC header information for SNAP packets; if we have a SNAP
header, just call snap_print() and return its return value, regardless
of whether it's 1 or 0, don't fall into the code to print raw LLC header
information - and don't print it with -e, either.
If llc_print() returns 0, just call the default packet printer, don't
print the MAC-layer header or the extracted ethertype - llc_print() will
print the source and destination MAC addresses and whatever type
information is in the LLC or SNAP headers.
If we don't know the DSAP/LSAP, and it's an information frame (numbered
or not) and not an XID frame, return 0, so that we give a hex dump of
the raw payload.
In addition, print the length when printing SNAP header information with
-e.
The purpose of this macro was to enable the file-by-file switch to NDO,
after which only tcpdump.c had a use of it and the definitions guarded
by it. Update tcpdump.c not to require them any more and dismiss the
unused definitions.
Check only the amount of length that matters at any given point; yes,
this means we do multiple checks, but so it goes.
We don't need to check for LLC+SNAP - llc_print() does that for us. We
do, however, need to check to make sure we can safely skip the Fore
header.
And, as we require at least autoconf 2.61, and as autoconf 2.61 and
later have AC_TYPE_UINTn_T and AC_TYPE_INTn_T macros, we use them to
define the uintN_t and intN_t macros if the system doesn't define them
for us.
This lets us get rid of bitypes.h as well.
Both interface.h and netdissect.h include <pcap.h>, thus most files
should not include it regardless if these need it or not. The only
exceptions so far remain:
* addrtoname.c
* missing/datalinks.c
* missing/dlnames.c
* tcpdump.c
Remove lots of $Header's and a few $Id's that all belong to the former
CVS repository of tcpdump itself. These keywords have been frozen since
the migration to git in late 2008.
For each decoder that has more than one instance of truncation signaling
and prints the same string in each instance make sure that the string is
declared as "static const char tstr[]" right after the initial includes
block. Where necessary, replace fputs(s, stdout) with equivalent
printf("%s", s).
Make sure all of them are declared const and most of them -- static.
Proper declaration of token arrays is a common review point for new code
that is based on existing decoders. Thus fix the issue at its root.
