This rearranges bootctl a bit, so that it uses the usual verbs parsing
routines, and automatically searches the ESP in /boot, /efi or /boot/efi, thus
increasing compatibility with mainstream distros that insist on /boot/efi.
This also adds minimal support for running bootctl in a container environment:
when run inside a container verification of the ESP via raw block device
access, trusting the container manager to mount the ESP correctly. Moreover,
EFI variables are not accessed when running in the container.
If the ESP is not mounted with "iocharset=ascii", but with "iocharset=utf8"
(which is for example the default in Debian), the file system becomes case
sensitive. This means that a file created as "FooBarBaz" cannot be accessed as
"foobarbaz" since those are then considered different files.
Moreover, a file created as "FooBar" can then also not be accessed as "foobar",
and it also prevents such a file from being created, as both would use the same
8.3 short name "FOOBAR".
Even though the UEFI specification [0] does give the canonical spelling for
the files mentioned above, not all implementations completely conform to that,
so it's possible that those files would already exist, but with a different
spelling, causing subtle bugs when scanning or modifying the ESP.
While the proper fix would of course be that everybody conformed to the
standard, we can work around this problem by just referencing the files by
their 8.3 short names, i.e. using upper case.
Fixes: #3740
[0] <http://www.uefi.org/specifications>, version 2.6, section 3.5.1.1
This did not really work out as we had hoped. Trying to do this upstream
introduced several problems that probably makes it better suited as a
downstream patch after all. At any rate, it is not releaseable in the
current state, so we at least need to revert this before the release.
* by adjusting the path to binaries, but not do the same thing to the
search path we end up with inconsistent man-pages. Adjusting the search
path too would be quite messy, and it is not at all obvious that this is
worth the effort, but at any rate it would have to be done before we
could ship this.
* this means that distributed man-pages does not make sense as they depend
on config options, and for better or worse we are still distributing
man pages, so that is something that definitely needs sorting out before
we could ship with this patch.
* we have long held that split-usr is only minimally supported in order
to boot, and something we hope will eventually go away. So before we start
adding even more magic/effort in order to make this work nicely, we should
probably question if it makes sense at all.
In particular, use /lib/systemd instead of /usr/lib/systemd in distributions
like Debian which still have not adopted a /usr merge setup.
Use XML entities from man/custom-entities.ent to replace configured paths while
doing XSLT processing of the original XML files. There was precedent of some
files (such as systemd.generator.xml) which were already using this approach.
This addresses most of the (manual) fixes from this patch:
http://anonscm.debian.org/cgit/pkg-systemd/systemd.git/tree/debian/patches/Fix-paths-in-man-pages.patch?h=experimental-220
The idea of using generic XML entities was presented here:
http://lists.freedesktop.org/archives/systemd-devel/2015-May/032240.html
This patch solves almost all the issues, with the exception of:
- Path to /bin/mount and /bin/umount.
- Generic statements about preference of /lib over /etc.
These will be handled separately by follow up patches.
Tested:
- With default configure settings, ran "make install" to two separate
directories and compared the output to confirm they matched exactly.
- Used a set of configure flags including $CONFFLAGS from Debian:
http://anonscm.debian.org/cgit/pkg-systemd/systemd.git/tree/debian/rules
Installed the tree and confirmed the paths use /lib/systemd instead of
/usr/lib/systemd and that no other unexpected differences exist.
- Confirmed that `make distcheck` still passes.
What used to be gummiboot, was renamed sd-boot when it was merged into
systemd. Let's try to be a bit more consistent with the rest of systemd
and rename it again as follows:
The EFI bootloader is now called 'systemd-bootx64.efi', and its sources are in
'src/boot/efi/'. The drop-in directory where bootctl will find EFI loaders
is now /usr/lib/systemd/boot/efi/.
It is annoying when we have dead links on fd.o.
Add project='man-pages|die-net|archlinux' to <citerefentry>-ies.
In generated html, add external links to
http://man7.org/linux/man-pages/man, http://linux.die.net/man/,
https://www.archlinux.org/.
By default, pages in sections 2 and 4 go to man7, since Michael
Kerrisk is the autorative source on kernel related stuff.
The rest of links goes to linux.die.net, because they have the
manpages.
Except for the pacman stuff, since it seems to be only available from
archlinux.org.
Poor gummiboot gets no link, because gummitboot(8) ain't to be found
on the net. According to common wisdom, that would mean that it does
not exist. But I have seen Kay using it, so I know it does, and
deserves to be found. Can somebody be nice and put it up somewhere?
