The BDRV_REQ_FUA flag can trivially be allowed in the crypt driver
as a passthrough to the underlying block driver.
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170927125340.12360-7-berrange@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Instead of sector offset, take the bytes offset when encrypting
or decrypting data.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170927125340.12360-6-berrange@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Make the crypto driver implement the bdrv_co_preadv|pwritev
callbacks, and also use bdrv_co_preadv|pwritev for I/O
with the protocol driver beneath. This replaces sector based
I/O with byte based I/O, and allows us to stop assuming the
physical sector size matches the encryption sector size.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170927125340.12360-5-berrange@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The crypto APIs report the offset of the data payload as an uint64_t
type, but the block driver is casting to size_t or ssize_t which will
potentially truncate.
Most of the block APIs use int64_t for offsets meanwhile, so even if
using uint64_t in the crypto block driver we are still at risk of
truncation.
Change the block crypto driver to use uint64_t, but add asserts that
the value is less than INT64_MAX.
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170927125340.12360-4-berrange@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Using 16KB bounce buffers creates a significant performance
penalty for I/O to encrypted volumes on storage which high
I/O latency (rotating rust & network drives), because it
triggers lots of fairly small I/O operations.
On tests with rotating rust, and cache=none|directsync,
write speed increased from 2MiB/s to 32MiB/s, on a par
with that achieved by the in-kernel luks driver. With
other cache modes the in-kernel driver is still notably
faster because it is able to report completion of the
I/O request before any encryption is done, while the
in-QEMU driver must encrypt the data before completion.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170927125340.12360-2-berrange@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Improve our braindead copy-on-read implementation. Pre-patch,
we have multiple issues:
- we create a bounce buffer and perform a write for the entire
request, even if the active image already has 99% of the
clusters occupied, and really only needs to copy-on-read the
remaining 1% of the clusters
- our bounce buffer was as large as the read request, and can
needlessly exhaust our memory by using double the memory of
the request size (the original request plus our bounce buffer),
rather than a capped maximum overhead beyond the original
- if a driver has a max_transfer limit, we are bypassing the
normal code in bdrv_aligned_preadv() that fragments to that
limit, and instead attempt to read the entire buffer from the
driver in one go, which some drivers may assert on
- a client can request a large request of nearly 2G such that
rounding the request out to cluster boundaries results in a
byte count larger than 2G. While this cannot exceed 32 bits,
it DOES have some follow-on problems:
-- the call to bdrv_driver_pread() can assert for exceeding
BDRV_REQUEST_MAX_BYTES, if the driver is old and lacks
.bdrv_co_preadv
-- if the buffer is all zeroes, the subsequent call to
bdrv_co_do_pwrite_zeroes is a no-op due to a negative size,
which means we did not actually copy on read
Fix all of these issues by breaking up the action into a loop,
where each iteration is capped to sane limits. Also, querying
the allocation status allows us to optimize: when data is
already present in the active layer, we don't need to bounce.
Note that the code has a telling comment that copy-on-read
should probably be a filter driver rather than a bolt-on hack
in io.c; but that remains a task for another day.
CC: qemu-stable@nongnu.org
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make it possible to inject errors on writes performed during a
read operation due to copy-on-read semantics.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Handle a 0-length block status request up front, with a uniform
return value claiming the area is not allocated.
Most callers don't pass a length of 0 to bdrv_get_block_status()
and friends; but it definitely happens with a 0-length read when
copy-on-read is enabled. While we could audit all callers to
ensure that they never make a 0-length request, and then assert
that fact, it was just as easy to fix things to always report
success (as long as the callers are careful to not go into an
infinite loop). However, we had inconsistent behavior on whether
the status is reported as allocated or defers to the backing
layer, depending on what callbacks the driver implements, and
possibly wasting quite a few CPU cycles to get to that answer.
Consistently reporting unallocated up front doesn't really hurt
anything, and makes it easier both for callers (0-length requests
now have well-defined behavior) and for drivers (drivers don't
have to deal with 0-length requests).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We don't need to make any assumptions about the graph layout above the
top node of the commit operation any more. Remove the use of
bdrv_find_overlay() and related variables from the commit job code.
bdrv_drop_intermediate() doesn't use the 'active' parameter any more, so
we can just drop it.
The overlay node was previously added to the block job to get a
BLK_PERM_GRAPH_MOD. We really need to respect those permissions in
bdrv_drop_intermediate() now, but as long as we haven't figured out yet
how BLK_PERM_GRAPH_MOD is actually supposed to work, just leave a TODO
comment there.
With this change, it is now possible to perform another block job on an
overlay node without conflicts. qemu-iotests 030 is changed accordingly.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This changes the commit block job to support operation in a graph where
there is more than a single active layer that references the top node.
This involves inserting the commit filter node not only on the path
between the given active node and the top node, but between the top node
and all of its parents.
On completion, bdrv_drop_intermediate() must consider all parents for
updating the backing file link. These parents may be backing files
themselves and as such read-only; reopen them temporarily if necessary.
Previously this was achieved by the bdrv_reopen() calls in the commit
block job that made overlay_bs read-write for the whole duration of the
block job, even though write access is only needed on completion.
Now that we consider all parents, overlay_bs is meaningless. It is left
in place in this commit, but we'll remove it soon.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that all callers are using byte-based interfaces, there's no
reason for our internal hbitmap to remain with sector-based
granularity. It also simplifies our internal scaling, since we
already know that hbitmap widens requests out to granularity
boundaries.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Both callers already had bytes available, but were scaling to
sectors. Move the scaling to internal code. In the case of
bdrv_aligned_pwritev(), we are now passing the exact offset
rather than a rounded sector-aligned value, but that's okay
as long as dirty bitmap widens start/bytes to granularity
boundaries.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that we have adjusted the majority of the calls this function
makes to be byte-based, it is easier to read the code if it makes
passes over the image using bytes rather than sectors.
iotests 165 was rather weak - on a default 64k-cluster image, where
bitmap granularity also defaults to 64k bytes, a single cluster of
the bitmap table thus covers (64*1024*8) bits which each cover 64k
bytes, or 32G of image space. But the test only uses a 1G image,
so it cannot trigger any more than one loop of the code in
store_bitmap_data(); and it was writing to the first cluster. In
order to test that we are properly aligning which portions of the
bitmap are being written to the file, we really want to test a case
where the first dirty bit returned by bdrv_dirty_iter_next() is not
aligned to the start of a cluster, which we can do by modifying the
test to write data that doesn't happen to fall in the first cluster
of the image.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that we have adjusted the majority of the calls this function
makes to be byte-based, it is easier to read the code if it makes
passes over the image using bytes rather than sectors.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is new code, but it is easier to read if it makes passes over
the image using bytes rather than sectors (and will get easier in
the future when bdrv_get_block_status is converted to byte-based).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that we have adjusted the majority of the calls this function
makes to be byte-based, it is easier to read the code if it makes
passes over the image using bytes rather than sectors.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some of the callers were already scaling bytes to sectors; others
can be easily converted to pass byte offsets, all in our shift
towards a consistent byte interface everywhere. Making the change
will also make it easier to write the hold-out callers to use byte
rather than sectors for their iterations; it also makes it easier
for a future dirty-bitmap patch to offload scaling over to the
internal hbitmap. Although all callers happen to pass
sector-aligned values, make the internal scaling robust to any
sub-sector requests.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Half the callers were already scaling bytes to sectors; the other
half can eventually be simplified to use byte iteration. Both
callers were already using the result as a bool, so make that
explicit. Making the change also makes it easier for a future
dirty-bitmap patch to offload scaling over to the internal hbitmap.
Remember, asking whether a byte is dirty is effectively asking
whether the entire granularity containing the byte is dirty, since
we only track dirtiness by granularity.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Thanks to recent cleanups, all callers were scaling a return value
of sectors into bytes; do the scaling internally instead.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Thanks to recent cleanups, most callers were scaling a return value
of sectors into bytes (the exception, in qcow2-bitmap, will be
converted to byte-based iteration later). Update the interface to
do the scaling internally instead.
In qcow2-bitmap, the code was specifically checking for an error
return of -1. To avoid a regression, we either have to make sure
we continue to return -1 (rather than a scaled -512) on error, or
we have to fix the caller to treat all negative values as error
rather than just one magic value. It's easy enough to make both
changes at the same time, even though either one in isolation
would work.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All callers to bdrv_dirty_iter_new() passed 0 for their initial
starting point, drop that parameter.
Most callers to bdrv_set_dirty_iter() were scaling a byte offset to
a sector number; the exception qcow2-bitmap will be converted later
to use byte rather than sector iteration. Move the scaling to occur
internally to dirty bitmap code instead, so that callers now pass
in bytes.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Change the qcow2 bitmap
helper function sectors_covered_by_bitmap_cluster(), renaming it
to bytes_covered_by_bitmap_cluster() in the process.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Right now, the dirty-bitmap code exposes the fact that we use
a scale of sector granularity in the underlying hbitmap to anything
that wants to serialize a dirty bitmap. It's nicer to uniformly
expose bytes as our dirty-bitmap interface, matching the previous
change to bitmap size. The only caller to serialization is currently
qcow2-cluster.c, which becomes a bit more verbose because it is still
tracking sectors for other reasons, but a later patch will fix that
to more uniformly use byte offsets everywhere. Likewise, within
dirty-bitmap, we have to add more assertions that we are not
truncating incorrectly, which can go away once the internal hbitmap
is byte-based rather than sector-based.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are still using an internal hbitmap that tracks a size in sectors,
with the granularity scaled down accordingly, because it lets us
use a shortcut for our iterators which are currently sector-based.
But there's no reason we can't track the dirty bitmap size in bytes,
since it is (mostly) an internal-only variable (remember, the size
is how many bytes are covered by the bitmap, not how many bytes the
bitmap occupies). A later cleanup will convert dirty bitmap
internals to be entirely byte-based, eliminating the intermediate
sector rounding added here; and technically, since bdrv_getlength()
already rounds up to sectors, our use of DIV_ROUND_UP is more for
theoretical completeness than for any actual rounding.
Use is_power_of_2() while at it, instead of open-coding that.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We're already reporting bytes for bdrv_dirty_bitmap_granularity();
mixing bytes and sectors in our return values is a recipe for
confusion. A later cleanup will convert dirty bitmap internals
to be entirely byte-based, but in the meantime, we should report
the bitmap size in bytes.
The only external caller in qcow2-bitmap.c is temporarily more verbose
(because it is still using sector-based math), but will later be
switched to track progress by bytes instead of sectors.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We've previously fixed several places where we failed to account
for possible errors from bdrv_nb_sectors(). Fix another one by
making bdrv_dirty_bitmap_truncate() take the new size from the
caller instead of querying itself; then adjust the sole caller
bdrv_truncate() to pass the size just determined by a successful
resize, or to reuse the size given to the original truncate
operation when refresh_total_sectors() was not able to confirm the
actual size (the two sizes can potentially differ according to
rounding constraints), thus avoiding sizing the bitmaps to -1.
This also fixes a bug where not all failure paths in
bdrv_truncate() would set errp.
Note that bdrv_truncate() is still a bit awkward. We may want
to revisit it later and clean up things to better guarantee that
a resize attempt either fails cleanly up front, or cannot fail
after guest-visible changes have been made (if temporary changes
are made, then they need to be cleanly rolled back). But that
is a task for another day; for now, the goal is the bare minimum
fix to ensure that just bdrv_dirty_bitmap_truncate() cannot fail.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We had several functions that no one is currently using, and which
use sector-based interfaces. I'm trying to convert towards byte-based
interfaces, so it's easier to just drop the unused functions:
bdrv_dirty_bitmap_get_meta
bdrv_dirty_bitmap_get_meta_locked
bdrv_dirty_bitmap_reset_meta
bdrv_dirty_bitmap_meta_granularity
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When subdividing a bitmap serialization, the code in hbitmap.c
enforces that start/count parameters are aligned (except that
count can end early at end-of-bitmap). We exposed this required
alignment through bdrv_dirty_bitmap_serialization_align(), but
forgot to actually check that we comply with it.
Fortunately, qcow2 is never dividing bitmap serialization smaller
than one cluster (which is a minimum of 512 bytes); so we are
always compliant with the serialization alignment (which insists
that we partition at least 64 bits per chunk) because we are doing
at least 4k bits per chunk.
Still, it's safer to add an assertion (for the unlikely case that
we'd ever support a cluster smaller than 512 bytes, or if the
hbitmap implementation changes what it considers to be aligned),
rather than leaving bdrv_dirty_bitmap_serialization_align()
without a caller.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The only client of hbitmap_serialization_granularity() is dirty-bitmap's
bdrv_dirty_bitmap_serialization_align(). Keeping the two names consistent
is worthwhile, and the shorter name is more representative of what the
function returns (the required alignment to be used for start/count of
other serialization functions, where violating the alignment causes
assertion failures).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZylugAAoJEH8JsnLIjy/Wp1QP/jtwre8WwtlX3SZ82cyiwonc
fODcokF6iEsX7vs9vMr8lkbwF4mjxaU2Xf/knC98J/6rCxM8DRP/MW4BZttTxDI9
++U926cIHHzjtSDalcjfTKnJD7PikHbLXz3SJ+u9hPnIeGs56hybCU6iHrrIcOTs
YSMtD3eUQ8B8JaoegKgNyqkhvfhEdHlWFCq9/T2YEWwYMzGt1jvSTRqe3vr8vIu3
v7QKvh35gm965yaUTGpv7Ej7TOBTWOaYBo9D1TBKNEZOFTBjqyldciyBoDhCF2P9
+4EsNTkZ7u20Rko41dzsZPzhjG10gm/lNZNj3Cul9ta4kQ0hGeOjEujd9L9ANTGl
gwnPPHKwgax5O+ctCPmrU7yHG+XIQD3gckC69qQeRXnPYQ4Jeo/LqhwjU+FcZfHs
97Lz6CHQHgtBP9JJwBMtUp77HJ58KPnnWIxGkb9u2vm4CpvRFkMrx5ekmj//9klX
5niRiqkNdrkEUnu/FIXOXxSmwnlhedAGQNq7ALSoW95El1QCy8Mm0eKEvmHyvZzd
z2gSufLX6ynOaG4x5oY5eezKm6F4Hxwt+w8Svj9PHXIrmrEIop11LG5MVsDGDjyh
XKiLddEIVKTYGwffX0CGTLYA34m2uHPkVVrMOIEvni3G6byXkb10+4pBpuTu/O/h
wQPFraquH1I2B5YETsMa
=7Bt2
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches
# gpg: Signature made Tue 26 Sep 2017 14:52:32 BST
# gpg: using RSA key 0x7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (24 commits)
block/qcow2-bitmap: fix use of uninitialized pointer
qemu-iotests: add shrinking image test
qcow2: add shrink image support
qcow2: add qcow2_cache_discard
qemu-img: add --shrink flag for resize
iotests: fix 181: enable postcopy-ram capability on target
qemu-iotests: Test change-backing-file command
block: Fix permissions after bdrv_reopen()
block: reopen: Queue children after their parents
block: Base permissions on rw state after reopen
block: Add reopen queue to bdrv_check_perm()
block: Add reopen_queue to bdrv_child_perm()
qemu-io: Drop write permissions before read-only reopen
block: Clean up some bad code in the vvfat driver
block/throttle-groups.c: allocate RestartData on the heap
throttle: Assert that bkt->max is valid in throttle_compute_wait()
iotests: Print full path of bad output if mismatch
iotests: use virtio aliases for 067
iotests: use -ccw on s390x for 051
iotests: use -ccw on s390x for 040, 139, and 182
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Without initialization to zero dirty_bitmap field may be not zero
for a bitmap which should not be stored and
qcow2_store_persistent_dirty_bitmaps will erroneously call
store_bitmap for it which leads to SIGSEGV on bdrv_dirty_bitmap_name.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20170922144353.4220-1-vsementsov@virtuozzo.com
Cc: qemu-stable@nongnu.org
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
This patch add shrinking of the image file for qcow2. As a result, this allows
us to reduce the virtual image size and free up space on the disk without
copying the image. Image can be fragmented and shrink is done by punching holes
in the image file.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20170918124230.8152-4-pbutsykin@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Whenever l2/refcount table clusters are discarded from the file we can
automatically drop unnecessary content of the cache tables. This reduces
the chance of eviction useful cache data and eliminates inconsistent data
in the cache with the data in the file.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20170918124230.8152-3-pbutsykin@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
In the context of bdrv_reopen(), we'll have to look at the state of the
graph as it will be after the reopen. This interface addition is in
preparation for the change.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Remove the unnecessary home-grown redefinition of the assert() macro here,
and remove the unusable debug code at the end of the checkpoint() function.
The code there uses assert() with side-effects (assignment to the "mapping"
variable), which should be avoided. Looking more closely, it seems as it is
apparently also only usable for one certain directory layout (with a file
named USB.H in it) and thus is of no use for the rest of the world.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
RestartData is the opaque data of the throttle_group_restart_queue_entry
coroutine. By being stack allocated, it isn't available anymore if
aio_co_enter schedules the coroutine with a bottom half and runs after
throttle_group_restart_queue returns.
Cc: qemu-stable@nongnu.org
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
People get surprised when, after "qemu-img create -f raw /dev/sdX", they
still see qcow2 with "qemu-img info", if previously the bdev had a qcow2
header. While this is natural because raw doesn't need to write any
magic bytes during creation, hdev_create is free to clear out the first
sector to make sure the stale qcow2 header doesn't cause such confusion.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It's incorrect to return success rc >= 0 if we skip qio_channel_writev_all()
call due to s->quit.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20170920124507.18841-4-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
If we are woken up from while() loop in nbd_read_reply_entry
handles must be equal. If we are woken up from
nbd_recv_coroutines_wake_all s->quit must be true, so we do
not need checking handles equality.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20170920124507.18841-3-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
"NBDReply *reply" parameter of nbd_co_receive_reply is used only
to pass return value for nbd_co_request (reply.error). Remove it
and use function return value instead.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20170920124507.18841-2-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
If 'bs' is a complex expression, we were only casting the front half
rather than the full expression. Luckily, none of the callers were
passing bad arguments, but it's better to be robust up front.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20170918214649.17550-1-eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
It is a common requirement for virtual machine to send persistent
reservations, but this currently requires either running QEMU with
CAP_SYS_RAWIO, or using out-of-tree patches that let an unprivileged
QEMU bypass Linux's filter on SG_IO commands.
As an alternative mechanism, the next patches will introduce a
privileged helper to run persistent reservation commands without
expanding QEMU's attack surface unnecessarily.
The helper is invoked through a "pr-manager" QOM object, to which
file-posix.c passes SG_IO requests for PERSISTENT RESERVE OUT and
PERSISTENT RESERVE IN commands. For example:
$ qemu-system-x86_64
-device virtio-scsi \
-object pr-manager-helper,id=helper0,path=/var/run/qemu-pr-helper.sock
-drive if=none,id=hd,driver=raw,file.filename=/dev/sdb,file.pr-manager=helper0
-device scsi-block,drive=hd
or:
$ qemu-system-x86_64
-device virtio-scsi \
-object pr-manager-helper,id=helper0,path=/var/run/qemu-pr-helper.sock
-blockdev node-name=hd,driver=raw,file.driver=host_device,file.filename=/dev/sdb,file.pr-manager=helper0
-device scsi-block,drive=hd
Multiple pr-manager implementations are conceivable and possible, though
only one is implemented right now. For example, a pr-manager could:
- talk directly to the multipath daemon from a privileged QEMU
(i.e. QEMU links to libmpathpersist); this makes reservation work
properly with multipath, but still requires CAP_SYS_RAWIO
- use the Linux IOC_PR_* ioctls (they require CAP_SYS_ADMIN though)
- more interestingly, implement reservations directly in QEMU
through file system locks or a shared database (e.g. sqlite)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tidy up some of the warn_report() messages after having converted them
to use warn_report().
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <9cb1d23551898c9c9a5f84da6773e99871285120.1505158760.git.alistair.francis@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert all the multi-line uses of fprintf(stderr, "warning:"..."\n"...
to use warn_report() instead. This helps standardise on a single
method of printing warnings to the user.
All of the warnings were changed using these commands:
find ./* -type f -exec sed -i \
'N; {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N; {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N; {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N;N; {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
Indentation fixed up manually afterwards.
Some of the lines were manually edited to reduce the line length to below
80 charecters. Some of the lines with newlines in the middle of the
string were also manually edit to avoid checkpatch errrors.
The #include lines were manually updated to allow the code to compile.
Several of the warning messages can be improved after this patch, to
keep this patch mechanical this has been moved into a later patch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Jason Wang <jasowang@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <5def63849ca8f551630c6f2b45bcb1c482f765a6.1505158760.git.alistair.francis@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert all the single line uses of fprintf(stderr, "warning:"..."\n"...
to use warn_report() instead. This helps standardise on a single
method of printing warnings to the user.
All of the warnings were changed using this command:
find ./* -type f -exec sed -i \
's|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig' \
{} +
Some of the lines were manually edited to reduce the line length to below
80 charecters.
The #include lines were manually updated to allow the code to compile.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Michael Roth <mdroth@linux.vnet.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com> [mips]
Message-Id: <ae8f8a7f0a88ded61743dff2adade21f8122a9e7.1505158760.git.alistair.francis@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In a previous patch (3dc6f86936) we
converted uses of error_report("warning:"... to use warn_report()
instead. This was to help standardise on a single method of printing
warnings to the user.
There appears to have been some cases that slipped through in patch sets
applied around the same time, this patch catches the few remaining
cases.
All of the warnings were changed using this command:
find ./* -type f -exec sed -i \
's|error_report(".*warning[,:] |warn_report("|Ig' {} +
Indentation fixed up manually afterwards.
Two messages were manually fixed up as well.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <eec8cba0d5434bd828639e5e45f12182490ff47d.1505158760.git.alistair.francis@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Complete the transition by renaming this header, which was
shared by block/iscsi.c and the SCSI emulation code.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
util/scsi.c includes some SCSI code that is shared by block/iscsi.c and
hw/scsi, but the introduction of the persistent reservation helper
will add many more instances of this. There is also include/block/scsi.h,
which actually is not part of the core block layer.
The persistent reservation manager will also need a home. A scsi/
directory provides one for both the aforementioned shared code and
the PR manager code.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
So that it can be reused outside of iscsi.c.
Also update MAINTAINERS to include the new files in SCSI section.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170821141008.19383-2-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Daniel P. Berrange: [0/2] Fix / skip recent iotests with LUKS driver
- Eric Blake: [0/3] nbd: Use common read/write-all qio functions
-----BEGIN PGP SIGNATURE-----
Comment: Public key at http://people.redhat.com/eblake/eblake.gpg
iQEcBAABCAAGBQJZsBGjAAoJEKeha0olJ0NqVRoH/iiNEB2SlZFFl5W++wf3Ekq/
lvtZjK3rxpvRXvy6LiRsYVs27Etc8E9aSw2UK6aaqgA3qR8g3zdmwUZb9w3slkeI
OXedt0fS5IpQ4UP0ORUBb/LgyOgW3uA0UjHBTEAKl0SyvFPx+TrTZXxqQUqlAc9A
lFaA0g71xvfqWWhXmt0PQjRr9bBEpe+4L4NgOypa+Z3xbBAektx390S8N/b/P8fC
FNwAqBPTY5XAgJGnEhL9EUOdUWnVgoyG1MR63puJzULYi+2+TlpR2w030qRif75b
h7TqYUvwKLnoqMyhBb5LmyhcqwNdphz/1DsEudk18XGuvC94WYkopC3rT7TPWLs=
=vGUc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ericb/tags/pull-nbd-2017-09-06' into staging
nbd patches for 2017-09-06
- Daniel P. Berrange: [0/2] Fix / skip recent iotests with LUKS driver
- Eric Blake: [0/3] nbd: Use common read/write-all qio functions
# gpg: Signature made Wed 06 Sep 2017 16:17:55 BST
# gpg: using RSA key 0xA7A16B4A2527436A
# gpg: Good signature from "Eric Blake <eblake@redhat.com>"
# gpg: aka "Eric Blake (Free Software Programmer) <ebb9@byu.net>"
# gpg: aka "[jpeg image of size 6874]"
# Primary key fingerprint: 71C2 CC22 B1C4 6029 27D2 F3AA A7A1 6B4A 2527 436A
* remotes/ericb/tags/pull-nbd-2017-09-06:
nbd: Use new qio_channel_*_all() functions
io: Add new qio_channel_read{, v}_all_eof functions
io: Yield rather than wait when already in coroutine
iotests: blacklist 194 with the luks driver
iotests: rewrite 192 to use _launch_qemu to fix LUKS support
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rather than open-coding our own read/write-all functions, we
can make use of the recently-added qio code. It slightly
changes the error message in one of the iotests.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20170905191114.5959-4-eblake@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
After calling qcow2_inactivate(), all qcow2 caches must be flushed, but this
may not happen, because the last call qcow2_store_persistent_dirty_bitmaps()
can lead to marking l2/refcont cache as dirty.
Let's move qcow2_store_persistent_dirty_bitmaps() before the caсhe flushing
to fix it.
Cc: qemu-stable@nongnu.org
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
block/throttle.c uses existing I/O throttle infrastructure inside a
block filter driver. I/O operations are intercepted in the filter's
read/write coroutines, and referred to block/throttle-groups.c
The driver can be used with the syntax
-drive driver=throttle,file.filename=foo.qcow2,throttle-group=bar
which registers the throttle filter node with the ThrottleGroup 'bar'. The
given group must be created beforehand with object-add or -object.
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
ThrottleGroup is converted to an object. This will allow the future
throttle block filter drive easy creation and configuration of throttle
groups in QMP and cli.
A new QAPI struct, ThrottleLimits, is introduced to provide a shared
struct for all throttle configuration needs in QMP.
ThrottleGroups can be created via CLI as
-object throttle-group,id=foo,x-iops-total=100,x-..
where x-* are individual limit properties. Since we can't add non-scalar
properties in -object this interface must be used instead. However,
setting these properties must be disabled after initialization because
certain combinations of limits are forbidden and thus configuration
changes should be done in one transaction. The individual properties
will go away when support for non-scalar values in CLI is implemented
and thus are marked as experimental.
ThrottleGroup also has a `limits` property that uses the ThrottleLimits
struct. It can be used to create ThrottleGroups or set the
configuration in existing groups as follows:
{ "execute": "object-add",
"arguments": {
"qom-type": "throttle-group",
"id": "foo",
"props" : {
"limits": {
"iops-total": 100
}
}
}
}
{ "execute" : "qom-set",
"arguments" : {
"path" : "foo",
"property" : "limits",
"value" : {
"iops-total" : 99
}
}
}
This also means a group's configuration can be fetched with qom-get.
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Move the CoMutex and CoQueue inits inside throttle_group_register_tgm()
which is called whenever a ThrottleGroupMember is initialized. There's
no need for them to be separate.
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
timer_cb() needs to know about the current Aio context of the throttle
request that is woken up. In order to make ThrottleGroupMember backend
agnostic, this information is stored in an aio_context field instead of
accessing it from BlockBackend.
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This commit eliminates the 1:1 relationship between BlockBackend and
throttle group state. Users will be able to create multiple throttle
nodes, each with its own throttle group state, in the future. The
throttle group state cannot be per-BlockBackend anymore, it must be
per-throttle node. This is done by gathering ThrottleGroup membership
details from BlockBackendPublic into ThrottleGroupMember and refactoring
existing code to use the structure.
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The non-blocking connect mechanism is obsolete, and it doesn't
work well in inet connection, because it will call getaddrinfo
first and getaddrinfo will blocks on DNS lookups. Since commit
e65c67e4 & d984464e, the non-blocking connect of migration goes
through QIOChannel in a different manner(using a thread), and
nobody use this old non-blocking connect anymore.
Any newly written code which needs a non-blocking connect should
use the QIOChannel code, so we can drop NonBlockingConnectHandler
as a concept entirely.
Suggested-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Omitting the check for whether bdrv_getlength() and bdrv_truncate()
failed meant that it was theoretically possible to return an
incorrect offset to the caller. More likely, conditions for either
of these functions to fail would also cause one of our other calls
(such as bdrv_pread() or bdrv_pwrite_sync()) to also fail, but
auditing that we are safe is difficult compared to just patching
things to always forward on the error rather than ignoring it.
Use osdep.h macros instead of open-coded rounding while in the
area.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The old signature has an ambiguous meaning for a return of 0:
either no allocation was requested or necessary, or an error
occurred (but any errno associated with the error is lost to
the caller, which then has to assume EIO).
Better is to follow the example of qcow2, by changing the
signature to have a separate return value that cleanly
distinguishes between failure and success, along with a
parameter that cleanly holds a 64-bit value. Then update all
callers.
While auditing that all return paths return a negative errno
(rather than -1), I also simplified places where we can pass
NULL rather than a local Error that just gets thrown away.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_co_get_block_status_from_file() and
bdrv_co_get_block_status_from_backing() set *file to bs->file and
bs->backing respectively, so that bdrv_co_get_block_status() can recurse
to them. Future block drivers won't have to duplicate code to implement
this.
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that bdrv_truncate is passed to bs->file by default, remove the
callback from block/blkdebug.c and set is_filter to true. is_filter also gives
access to other callbacks that are forwarded automatically to bs->file for
filters.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This function is not used anywhere, so remove it.
Markus Armbruster adds:
The i82078 floppy device model used to call bdrv_media_changed() to
implement its media change bit when backed by a host floppy. This
went away in 21fcf36 "fdc: simplify media change handling".
Probably broke host floppy media change. Host floppy pass-through
was dropped in commit f709623. bdrv_media_changed() has never been
used for anything else. Remove it.
(Source is Message-ID: <87y3ruaypm.fsf@dusky.pond.sub.org>)
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that all usages have been converted to user lookup helpers.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170822132255.23945-14-marcandre.lureau@redhat.com>
[Rebased, superfluous local variable dropped, missing
check-qom-proplist.c update added]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-17-git-send-email-armbru@redhat.com>
Currently, a FOO_lookup is an array of strings terminated by a NULL
sentinel.
A future patch will generate enums with "holes". NULL-termination
will cease to work then.
To prepare for that, store the length in the FOO_lookup by wrapping it
in a struct and adding a member for the length.
The sentinel will be dropped next.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170822132255.23945-13-marcandre.lureau@redhat.com>
[Basically redone]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-16-git-send-email-armbru@redhat.com>
[Rebased]
The next commit will put it to use. May look pointless now, but we're
going to change the FOO_lookup's type, and then it'll help.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-13-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
The error message on invalid blkdebug events changes from
qemu-system-x86_64: LOCATION: Invalid event name "VALUE"
to
qemu-system-x86_64: LOCATION: invalid parameter value: VALUE
Slight degradation, but the message is sub-par even before the patch.
When complaining about a parameter value, both parameter name and
value should be mentioned, as the value may well not be unique. Left
for another day.
Also left is the error message's unhelpful location: it points to the
config=FILENAME rather than into that file.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170822132255.23945-11-marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Rebased, commit message rewritten]
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: qemu-block@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-8-git-send-email-armbru@redhat.com>
The lookup tables have a sentinel, no need to make callers pass their
size.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-3-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[Rebased, commit message corrected]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=jCiK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/elmarco/tags/tidy-pull-request' into staging
# gpg: Signature made Thu 31 Aug 2017 11:29:33 BST
# gpg: using RSA key 0xDAE8E10975969CE5
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>"
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/tidy-pull-request: (29 commits)
eepro100: replace g_malloc()+memcpy() with g_memdup()
test-iov: replace g_malloc()+memcpy() with g_memdup()
i386: replace g_malloc()+memcpy() with g_memdup()
i386: introduce ELF_NOTE_SIZE macro
decnumber: use DIV_ROUND_UP
kvm: use DIV_ROUND_UP
i386/dump: use DIV_ROUND_UP
ppc: use DIV_ROUND_UP
msix: use DIV_ROUND_UP
usb-hub: use DIV_ROUND_UP
q35: use DIV_ROUND_UP
piix: use DIV_ROUND_UP
virtio-serial: use DIV_ROUND_UP
console: use DIV_ROUND_UP
monitor: use DIV_ROUND_UP
virtio-gpu: use DIV_ROUND_UP
vga: use DIV_ROUND_UP
ui: use DIV_ROUND_UP
vnc: use DIV_ROUND_UP
vvfat: use DIV_ROUND_UP
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
iQEcBAABAgAGBQJZp8cdAAoJEJykq7OBq3PIyeQIALXlHMTJM+I2dfUZfkIYFrEk
Euf0z1URMJ9k5hKy1kIhAVlmGWs2fB1snTCm9tZjCtPqMjH5EDWb8z+zrqmorpcQ
LyIccYdT/XrFeU1x+n4PlhaubQKXiAfZbUbgZpbkZwGgX0k51gx3V9z1smHme6AX
CIODhgotqbJ0Hy2kuAP8TM2OPgx1tcyel34GuT5e3Rrb8nL0QfHfG4nxcpWBB0q8
iipoJfBvKWpRV0azSg+s51x1FFcB3iDKr81uBVABOyLtVW13nF6EMRIP76rqy5qp
relNDo6kdmh0W19motNPjOa4BhnPQakEfF+bdARBOJPbXsFzd5X193yQBKW+nq4=
=5ltA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/block-pull-request' into staging
# gpg: Signature made Thu 31 Aug 2017 09:21:49 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/block-pull-request:
qcow2: allocate cluster_cache/cluster_data on demand
qemu-doc: Add UUID support in initiator name
tests: migration/guestperf Python 2.6 argparse compatibility
docker.py: Python 2.6 argparse compatibility
scripts: add argparse module for Python 2.6 compatibility
misc: Remove unused Error variables
oslib-posix: Print errors before aborting on qemu_alloc_stack()
throttle: Test the valid range of config values
throttle: Make burst_length 64bit and add range checks
throttle: Make LeakyBucket.avg and LeakyBucket.max integer types
throttle: Remove throttle_fix_bucket() / throttle_unfix_bucket()
throttle: Make throttle_is_valid() a bit less verbose
throttle: Update the throttle_fix_bucket() documentation
throttle: Fix wrong variable name in the header documentation
nvme: Fix get/set number of queues feature, again
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I used the clang-tidy qemu-round check to generate the fix:
https://github.com/elmarco/clang-tools-extra
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
I used the clang-tidy qemu-round check to generate the fix:
https://github.com/elmarco/clang-tools-extra
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
I used the clang-tidy qemu-round check to generate the fix:
https://github.com/elmarco/clang-tools-extra
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
I used the clang-tidy qemu-round check to generate the fix:
https://github.com/elmarco/clang-tools-extra
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
I used the clang-tidy qemu-round check to generate the fix:
https://github.com/elmarco/clang-tools-extra
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Add nbd_co_request, to remove code duplications in
nbd_client_co_{pwrite,pread,...} functions. Also this is
needed for further refactoring.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20170804151440.320927-8-vsementsov@virtuozzo.com>
[eblake: make nbd_co_request a wrapper, rather than merging two
existing functions]
Signed-off-by: Eric Blake <eblake@redhat.com>
Rename nbd_recv_coroutines_enter_all to nbd_recv_coroutines_wake_all,
as it most probably just adds all recv coroutines into co_queue_wakeup,
rather than directly enter them.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20170804151440.320927-9-vsementsov@virtuozzo.com>
[eblake: tweak commit message]
Signed-off-by: Eric Blake <eblake@redhat.com>
Use int variable for nbd_co_send_request return value (as
nbd_co_send_request returns int).
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20170804151440.320927-6-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
The following segfault is encountered if the NBD server closes the UNIX
domain socket immediately after negotiation:
Program terminated with signal SIGSEGV, Segmentation fault.
#0 aio_co_schedule (ctx=0x0, co=0xd3c0ff2ef0) at util/async.c:441
441 QSLIST_INSERT_HEAD_ATOMIC(&ctx->scheduled_coroutines,
(gdb) bt
#0 0x000000d3c01a50f8 in aio_co_schedule (ctx=0x0, co=0xd3c0ff2ef0) at util/async.c:441
#1 0x000000d3c012fa90 in nbd_coroutine_end (bs=bs@entry=0xd3c0fec650, request=<optimized out>) at block/nbd-client.c:207
#2 0x000000d3c012fb58 in nbd_client_co_preadv (bs=0xd3c0fec650, offset=0, bytes=<optimized out>, qiov=0x7ffc10a91b20, flags=0) at block/nbd-client.c:237
#3 0x000000d3c0128e63 in bdrv_driver_preadv (bs=bs@entry=0xd3c0fec650, offset=offset@entry=0, bytes=bytes@entry=512, qiov=qiov@entry=0x7ffc10a91b20, flags=0) at block/io.c:836
#4 0x000000d3c012c3e0 in bdrv_aligned_preadv (child=child@entry=0xd3c0ff51d0, req=req@entry=0x7f31885d6e90, offset=offset@entry=0, bytes=bytes@entry=512, align=align@entry=1, qiov=qiov@entry=0x7ffc10a91b20, f
+lags=0) at block/io.c:1086
#5 0x000000d3c012c6b8 in bdrv_co_preadv (child=0xd3c0ff51d0, offset=offset@entry=0, bytes=bytes@entry=512, qiov=qiov@entry=0x7ffc10a91b20, flags=flags@entry=0) at block/io.c:1182
#6 0x000000d3c011cc17 in blk_co_preadv (blk=0xd3c0ff4f80, offset=0, bytes=512, qiov=0x7ffc10a91b20, flags=0) at block/block-backend.c:1032
#7 0x000000d3c011ccec in blk_read_entry (opaque=0x7ffc10a91b40) at block/block-backend.c:1079
#8 0x000000d3c01bbb96 in coroutine_trampoline (i0=<optimized out>, i1=<optimized out>) at util/coroutine-ucontext.c:79
#9 0x00007f3196cb8600 in __start_context () at /lib64/libc.so.6
The problem is that nbd_client_init() uses
nbd_client_attach_aio_context() -> aio_co_schedule(new_context,
client->read_reply_co). Execution of read_reply_co is deferred to a BH
which doesn't run until later.
In the mean time blk_co_preadv() can be called and nbd_coroutine_end()
calls aio_wake() on read_reply_co. At this point in time
read_reply_co's ctx isn't set because it has never been entered yet.
This patch simplifies the nbd_co_send_request() ->
nbd_co_receive_reply() -> nbd_coroutine_end() lifecycle to just
nbd_co_send_request() -> nbd_co_receive_reply(). The request is "ended"
if an error occurs at any point. Callers no longer have to invoke
nbd_coroutine_end().
This cleanup also eliminates the segfault because we don't call
aio_co_schedule() to wake up s->read_reply_co if sending the request
failed. It is only necessary to wake up s->read_reply_co if a reply was
received.
Note this only happens with UNIX domain sockets on Linux. It doesn't
seem possible to reproduce this with TCP sockets.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20170829122745.14309-2-stefanha@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Most qcow2 files are uncompressed so it is wasteful to allocate (32 + 1)
* cluster_size + 512 bytes upfront. Allocate s->cluster_cache and
s->cluster_data when the first read operation is performance on a
compressed cluster.
The buffers are freed in .bdrv_close(). .bdrv_open() no longer has any
code paths that can allocate these buffers, so remove the free functions
in the error code path.
This patch can result in significant memory savings when many qcow2
disks are attached or backing file chains are long:
Before 12.81% (1,023,193,088B)
After 5.36% (393,893,888B)
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170821135530.32344-1-stefanha@redhat.com
Cc: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
There's a few cases which we're passing an Error pointer to a function
only to discard it immediately afterwards without checking it. In
these cases we can simply remove the variable and pass NULL instead.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170829120836.16091-1-berto@igalia.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The following scenario leads to an assertion failure in
qio_channel_yield():
1. Request coroutine calls qio_channel_yield() successfully when sending
would block on the socket. It is now yielded.
2. nbd_read_reply_entry() calls nbd_recv_coroutines_enter_all() because
nbd_receive_reply() failed.
3. Request coroutine is entered and returns from qio_channel_yield().
Note that the socket fd handler has not fired yet so
ioc->write_coroutine is still set.
4. Request coroutine attempts to send the request body with nbd_rwv()
but the socket would still block. qio_channel_yield() is called
again and assert(!ioc->write_coroutine) is hit.
The problem is that nbd_read_reply_entry() does not distinguish between
request coroutines that are waiting to receive a reply and those that
are not.
This patch adds a per-request bool receiving flag so
nbd_read_reply_entry() can avoid spurious aio_wake() calls.
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20170822125113.5025-1-stefanha@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
These two conditions corresponds to mirror job's source and target,
which need to be allowed as they are part of the non-shared storage
migration workflow: failing to inactivate either will result in a
failure during migration completion.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170823134242.12080-3-famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
[eblake: improve comment grammar]
Signed-off-by: Eric Blake <eblake@redhat.com>
The logic will be fixed (extended), move it to a separate function.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170823134242.12080-2-famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
travis builds fail at HEAD at rc3 master with
block/nbd-client.c: In function ‘nbd_read_reply_entry’:
block/nbd-client.c:110:8: error: ‘ret’ may be used uninitialized in this function [-Werror=uninitialized]
fix it by initializing 'ret' to 0
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When we switched NBD to use coroutines for qemu 2.9 (in particular,
commit a12a712a), we introduced a regression: if a server sends us
garbage (such as a corrupted magic number), we quit the read loop
but do not stop sending further queued commands, resulting in the
client hanging when it never reads the response to those additional
commands. In qemu 2.8, we properly detected that the server is no
longer reliable, and cancelled all existing pending commands with
EIO, then tore down the socket so that all further command attempts
get EPIPE.
Restore the proper behavior of quitting (almost) all communication
with a broken server: Once we know we are out of sync or otherwise
can't trust the server, we must assume that any further incoming
data is unreliable and therefore end all pending commands with EIO,
and quit trying to send any further commands. As an exception, we
still (try to) send NBD_CMD_DISC to let the server know we are going
away (in part, because it is easier to do that than to further
refactor nbd_teardown_connection, and in part because it is the
only command where we do not have to wait for a reply).
Based on a patch by Vladimir Sementsov-Ogievskiy.
A malicious server can be created with the following hack,
followed by setting NBD_SERVER_DEBUG to a non-zero value in the
environment when running qemu-nbd:
| --- a/nbd/server.c
| +++ b/nbd/server.c
| @@ -919,6 +919,17 @@ static int nbd_send_reply(QIOChannel *ioc, NBDReply *reply, Error **errp)
| stl_be_p(buf + 4, reply->error);
| stq_be_p(buf + 8, reply->handle);
|
| + static int debug;
| + static int count;
| + if (!count++) {
| + const char *str = getenv("NBD_SERVER_DEBUG");
| + if (str) {
| + debug = atoi(str);
| + }
| + }
| + if (debug && !(count % debug)) {
| + buf[0] = 0;
| + }
| return nbd_write(ioc, buf, sizeof(buf), errp);
| }
Reported-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20170814213426.24681-1-eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
As in the case of nbd_export_new(), bdrv_invalidate_cache() can be
called when migration is still in progress. In this case we are not
ready to tighten the shared permissions fenced by blk->disable_perm.
Defer to a VM state change handler.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170815130740.31229-4-famz@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
It is reported that on Windows Subsystem for Linux, ofd operations fail
with -EINVAL. In other words, QEMU binary built with system headers that
exports F_OFD_SETLK doesn't necessarily run in an environment that
actually supports it:
$ qemu-system-aarch64 ... -drive file=test.vhdx,if=none,id=hd0 \
-device virtio-blk-pci,drive=hd0
qemu-system-aarch64: -drive file=test.vhdx,if=none,id=hd0: Failed to unlock byte 100
qemu-system-aarch64: -drive file=test.vhdx,if=none,id=hd0: Failed to unlock byte 100
qemu-system-aarch64: -drive file=test.vhdx,if=none,id=hd0: Failed to lock byte 100
As a matter of fact this is not WSL specific. It can happen when running
a QEMU compiled against a newer glibc on an older kernel, such as in
a containerized environment.
Let's do a runtime check to cope with that.
Reported-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qcow2_co_pwritev_compressed() should not call bdrv_truncate()
if determining the size failed.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It's been #if 0'd since its introduction in 2006, commit 585f8587.
We can revive dead code if we need it, but in the meantime, it has
bit-rotted (for example, not checking for failure in bdrv_getlength()).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
vpc_open() was checking for bdrv_getlength() failure in one, but
not the other, location.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit c096358e74 introduced assertion
checks for when qemu_mutex() functions are called without the
corresponding qemu_mutex_init() having initialized the mutex.
This uncovered a latent bug in qemu's nfs driver - in
nfs_client_close(), the NFSClient structure is overwritten with zeros,
prior to the mutex being destroyed.
Go ahead and destroy the mutex in nfs_client_close(), and change where
we call qemu_mutex_init() so that it is correctly balanced.
There are also a couple of memory leaks obscured by the memset, so this
fixes those as well.
Finally, we should be able to get rid of the memset(), as it isn't
necessary.
Cc: qemu-stable@nongnu.org
Signed-off-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This would be actually strange and error prone. If truncate() nowadays
will fail, there is something fatally wrong. Let's check for that during
the actual work.
The only fallback case is when the file is not zero initialized. In this
case we should switch to preallocation via fallocate().
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Markus Armbruster <armbru@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If we can not get the file length, the state of BDS is broken completely.
Return error to the caller.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Markus Armbruster <armbru@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Original idea beyond the code in question was the following: we have failed
to write zeroes with fallocate(FALLOC_FL_ZERO_RANGE) as the simplest
approach and via fallocate(FALLOC_FL_PUNCH_HOLE)/fallocate(0). We have the
only chance now: if the request comes beyond end of the file. Thus we
should calculate file length and respect the error code from that op.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Markus Armbruster <armbru@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Errors from the callees must be captured and propagated to our caller,
ensure this for both find_extent() and bdrv_getlength().
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This option was only added to allow 'null-co://' and 'null-aio://' as
filenames, its value never served any actual purpose and was ignored.
Nevertheless it was accepted as '-drive driver=null,filename=foo'.
The correct way to enable the protocol prefixes (and that without adding
a useless -drive option) is implementing .bdrv_parse_filename. This is
what this patch does.
Technically, this is an incompatible change, but the null block driver
is only used for benchmarking, testing and debugging, and an option
without effect isn't likely to be used by anyone anyway, so no bad
effects are to be expected.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
VHDX uses uint64_t types for most offsets, following the VHDX spec.
However, bdrv_truncate() takes an int64_t value for the truncating
offset. Check for overflow before calling bdrv_truncate().
While we are here, replace the bit shifting with QEMU_ALIGN_UP as well.
N.B.: For a compliant image this is not an issue, as the maximum VHDX
image size is defined per the spec to be 64TB.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Calls to bdrv_getlength() were not checking for error. In vhdx.c, this
can lead to truncating an image file, so it is a definite bug. In
vhdx-log.c, the path for improper behavior is less clear, but it is best
to check in any case.
Some minor code movement of the log_guid intialization, as well.
Reported-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The QUORUM_REPORT_BAD event has fields to report the sector in which
the error was detected and the number of affected sectors starting
from that one. This is important for read and write errors, but not
for flush errors.
For flush errors the current code reports the total size of the disk
image. That is however not useful information in this case. Moreover,
the bdrv_getlength() call can fail, and there's no good way of
handling that failure.
Since we're reporting useless information and we cannot even guarantee
to do it in a consistent way, this patch changes the code to report 0
instead in all cases.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are trace probes in bdrv_co_readv|writev, however, the
block drivers are being gradually moved over to using the
bdrv_co_preadv|pwritev functions instead. As a result some
block drivers miss the current probes. Move the probes
into bdrv_co_preadv|pwritev instead, so that they are triggered
by more (all?) I/O code paths.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170804105036.11879-1-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When skipping implicit nodes in bdrv_block_device_info(), we know that
bs0 is always non-NULL; initially, because it's taken from a BdrvChild
and a BdrvChild never has a NULL bs, and after the first iteration
because implicit nodes always have a backing file.
Remove the NULL check and add an assertion that the implicit node does
indeed have a backing file.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In trace format '#' flag of printf is forbidden. Fix it to '0x%'.
This patch is created by the following:
check that we have a problem
> find . -name trace-events | xargs grep '%#' | wc -l
56
check that there are no cases with additional printf flags before '#'
> find . -name trace-events | xargs grep "%[-+ 0'I]+#" | wc -l
0
check that there are no wrong usage of '#' and '0x' together
> find . -name trace-events | xargs grep '0x%#' | wc -l
0
fix the problem
> find . -name trace-events | xargs sed -i 's/%#/0x%/g'
[Eric Blake noted that xargs grep '%[-+ 0'I]+#' should be xargs grep
"%[-+ 0'I]+#" instead so the shell quoting is correct.
--Stefan]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170731160135.12101-3-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fix possible crash on error path in
qcow2_remove_persistent_dirty_bitmap. Although bitmap_free was added in
88ddffae8f the bug was introduced later in commit 469c71edc7 (when
qcow2_remove_persistent_dirty_bitmap was added).
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170714123341.373857-1-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Fix leak of the 'encryptopts' string, which was mistakenly
declared const.
Fix leak of QemuOpts entry which should not have been deleted
from the opts array.
Reported by: coverity
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170714103105.5781-1-berrange@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Commits 0db832f and 6cdbceb introduced the automatic insertion of filter
nodes above the top layer of mirror and commit block jobs. The
assumption made there was that since libvirt doesn't do node-level
management of the block layer yet, it shouldn't be affected by added
nodes.
This is true as far as commands issued by libvirt are concerned. It only
uses BlockBackend names to address nodes, so any operations it performs
still operate on the root of the tree as intended.
However, the assumption breaks down when you consider query commands,
which return data for the wrong node now. These commands also return
information on some child nodes (bs->file and/or bs->backing), which
libvirt does make use of, and which refer to the wrong nodes, too.
One of the consequences is that oVirt gets wrong information about the
image size and stops the VM in response as long as a mirror or commit
job is running:
https://bugzilla.redhat.com/show_bug.cgi?id=1470634
This patch fixes the problem by hiding the implicit nodes created
automatically by the mirror and commit block jobs in the output of
query-block and BlockBackend-based query-blockstats as long as the user
doesn't indicate that they are aware of those nodes by providing a node
name for them in the QMP command to start the block job.
The node-based commands query-named-block-nodes and query-blockstats
with query-nodes=true still show all nodes, including implicit ones.
This ensures that users that are capable of node-level management can
still access the full information; users that only know BlockBackends
won't use these commands.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
We used MAX() instead of the intended MIN() when computing how many
sectors to view in the current loop iteration of qcow2_measure(),
and passed in a value of INT_MAX sectors instead of our more usual
limit of BDRV_REQUEST_MAX_SECTORS (the latter avoids 32-bit overflow
on conversion to bytes). For small files, the bug is harmless:
bdrv_get_block_status_above() clamps its *pnum answer to the BDS
size, regardless of any insanely larger input request. However, for
any file at least 2T in size, we can very easily end up going into an
infinite loop (the maximum of 0x100000000 sectors and INT_MAX is a
64-bit quantity, which becomes 0 when assigned to int; once nb_sectors
is 0, we never make progress).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We've been documenting the value in bytes since its introduction
in commit b9a9b3a4 (v1.3), where it was actually reported in bytes.
Commit e4654d2 (v2.0) then removed things from block/qapi.c, in
preparation for a rewrite to a list of dirty sectors in the next
commit 21b5683 in block.c, but the new code mistakenly started
reporting in sectors.
Fixes: https://bugzilla.redhat.com/1441460
CC: qemu-stable@nongnu.org
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since commit cfc87e00 "block/vpc.c: Handle write failures in
get_image_offset()" older versions of gcc (in this case 4.7) incorrectly
warn that "ret" can be used uninitialised in vpc_co_pwritev().
Setting ret to 0 at the start of vpc_co_pwritev() prevents the warning
in gcc 4.7 and enables compilation with -Werror to succeed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1500625265-23844-1-git-send-email-mark.cave-ayland@ilande.co.uk
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
gcc 7 complains that the sprintf() might write a null byte beyond the
end of the tail buffer. That is wrong, but we can silence it by making
i unsigned (it can never be negative anyway, see the if condition right
before). For some reason, this allows gcc to suddenly accurately
calculate the range of i so we can give the tail[] array the exact size
it needs to have (which is 8 bytes) without gcc complaining.
In addition, let us convert the sprintf() to snprintf(), because that is
always nicer, and add an assertion about the range of the return value
afterwards so we can see that "8 - len" will never be negative and thus
"entry->name + MIN(j, 8 - len)" will never be out of bounds.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This prevents some host to guest memory content leaks.
Fixes: https://bugs.launchpad.net/qemu/+bug/1599539
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Write support works again when image contains non-ASCII names. It is either the
case when user created a non-ASCII filename, or when initial directory contained
a non-ASCII filename (since 0c36111f57)
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Also add links to related compatibility problems.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of listing only monitor-owned BlockBackends in query-block, also
add those anonymous BlockBackends that are owned by a qdev device and as
such under the control of the user.
This allows using query-block to inspect BlockBackends for the modern
configuration syntax with -blockdev and -device.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
This patch replaces the blk_next() loop in query-block by a
blk_all_next() one so that we also get access to BlockBackends that
aren't owned by the monitor. For now, the next thing we do is check
whether each BB has a name, so there is no semantic difference.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
With -blockdev/-device, users can indirectly create anonymous
BlockBackends, while the state of such backends is still of interest. As
a preparation for making such BBs visible in query-block, make sure that
they can be identified even without a name by adding the ID/QOM path of
their qdev device to BlockInfo.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Coverity (CID 1355236) points out that get_image_offset() doesn't check that
it actually succeeded in writing the updated block bitmap to the file.
Check the error return from bdrv_pwrite_sync() and propagate an error
response back up to the function which calls get_image_offset() for
a write so that it can return the error to its caller.
get_sector_offset() is only used for reads, but we move it to the
same API for consistency.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The function vmdk_read_cid() can fail if the read on the underlying
block device fails, or if there's a format error in the VMDK file.
However its API doesn't provide a mechanism to report these errors,
and in some cases we were returning a CID of 0 and in some cases a
CID of 0xffffffff, either of which might potentially be valid values.
Change the function to return 0 on success or a negative errno, and
return the CID via a uint32_t* argument. Update the callsites to
handle and propagate the error appropriately.
This fixes in passing a Coverity-spotted issue (CID 1350038) where
we weren't checking the return value from sscanf().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
throttle_config() cancels the timers of the calling BlockBackend. This
doesn't make sense because other BlockBackends in the group remain
untouched. There's no need to cancel the timers in the one specific
BlockBackend so let's not do that. Throttled requests will run as
scheduled and future requests will follow the new configuration. This
also allows a throttle group's configuration to be changed even when it
has no members.
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Clock type in throttling is currently inferred by the ThrottleTimer's
clock type even though it is a per-ThrottleGroup property; it doesn't
make sense to have different clock types in the same group. Moving this
to a field in ThrottleGroup can simplify some of the throttle functions.
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I can't see how overlay_bs could become NULL with the current code, but
other code in this function already checks it and we can make Coverity
happy with this check, so let's add it.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
We've had a shadowed 'ret' variable, which risks returning the wrong
value, introduced in commit b9c64947.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170710150559.30163-1-den@openvz.org
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The coroutine may run in a different AioContext, causing the
fd handler to busy wait. Fix this by resetting the handler
in restart_coroutine, before the coroutine is restarted.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20170629132749.997-12-pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
This makes the driver thread-safe. The CoMutex is dropped temporarily
while accessing the data clusters or the backing file.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20170629132749.997-10-pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
This will be used in the next patch, which will call bdrv_qed_do_open
with a CoMutex taken. bdrv_qed_init_state provides a nice place to
initialize it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20170629132749.997-9-pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
This will let the callback take a CoMutex in the next patch.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20170629132749.997-8-pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
This part is never called for in-place writes, move it away to avoid
the "backwards" coding style typical of callback-based code.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20170629132749.997-7-pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
The VirtualBox driver is using a mutex to order all allocating writes,
but it is not protecting accesses to the bitmap because they implicitly
happen under the AioContext mutex. Change this to use a CoRwlock
explicitly.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20170629132749.997-4-pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
The upstream NBD Protocol has defined a new extension to allow
the server to advertise block sizes to the client, as well as
a way for the client to inform the server whether it intends to
obey block sizes.
When using the block layer as the client, we will obey block
sizes; but when used as 'qemu-nbd -c' to hand off to the
kernel nbd module as the client, we are still waiting for the
kernel to implement a way for us to learn if it will honor
block sizes (perhaps by an addition to sysfs, rather than an
ioctl), as well as any way to tell the kernel what additional
block sizes to obey (NBD_SET_BLKSIZE appears to be accurate
for the minimum size, but preferred and maximum sizes would
probably be new ioctl()s), so until then, we need to make our
request for block sizes conditional.
When using ioctl(NBD_SET_BLKSIZE) to hand off to the kernel,
use the minimum block size as the sector size if it is larger
than 512, which also has the nice effect of cooperating with
(non-qemu) servers that don't do read-modify-write when
exposing a block device with 4k sectors; it might also allow
us to visit a file larger than 2T on a 32-bit kernel.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20170707203049.534-10-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The NBD Protocol is introducing some additional information
about exports, such as minimum request size and alignment, as
well as an advertised maximum request size. It will be easier
to feed this information back to the block layer if we gather
all the information into a struct, rather than adding yet more
pointer parameters during negotiation.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20170707203049.534-2-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert all uses of error_report("warning:"... to use warn_report()
instead. This helps standardise on a single method of printing warnings
to the user.
All of the warnings were changed using these two commands:
find ./* -type f -exec sed -i \
's|error_report(".*warning[,:] |warn_report("|Ig' {} +
Indentation fixed up manually afterwards.
The test-qdev-global-props test case was manually updated to ensure that
this patch passes make check (as the test cases are case sensitive).
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Cc: Jeff Cody <jcody@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Lieven <pl@kamp.de>
Cc: Josh Durgin <jdurgin@redhat.com>
Cc: "Richard W.M. Jones" <rjones@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Greg Kurz <groug@kaod.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Peter Chubb <peter.chubb@nicta.com.au>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Alexander Graf <agraf@suse.de>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Greg Kurz <groug@kaod.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Max Reitz <mreitz@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Message-Id: <e1cfa2cd47087c248dd24caca9c33d9af0c499b0.1499866456.git.alistair.francis@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Implement the preallocation modes falloc and full for growing qcow2
images.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170613202107.10125-15-mreitz@redhat.com
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Now alloc_refcount_block() only contains a single fail label, so it
makes more sense to just name it "fail" instead of "fail_block".
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170613202107.10125-14-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This function creates a collection of self-describing refcount
structures (including a new refcount table) at the end of a qcow2 image
file. Optionally, these structures can also describe a number of
additional clusters beyond themselves; this will be important for
preallocated truncation, which will place the data clusters and L2
tables there.
For now, we can use this function to replace the part of
alloc_refcount_block() that grows the refcount table (from which it is
actually derived).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170613202107.10125-13-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
We can support PREALLOC_MODE_METADATA by invoking preallocate() in
qcow2_truncate().
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170613202107.10125-12-mreitz@redhat.com
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
preallocate() is and will be called only from places that do not
otherwise need to lock s->lock: Currently that is qcow2_create2(), as of
a future patch it will be called from qcow2_truncate(), too.
It therefore makes sense to move locking that mutex into preallocate()
itself.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170613202107.10125-11-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This patch adds two new parameters to the preallocate() function so we
will be able to use it not just for preallocating a new image but also
for preallocated image growth.
The offset parameter allows the caller to specify a virtual offset from
which to start preallocating. For newly created images this is always 0,
but for preallocating growth this will be the old image length.
The new_length parameter specifies the supposed new length of the image
(basically the "end offset" for preallocation). During image truncation,
bdrv_getlength() will return the old image length so we cannot rely on
its return value then.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170613202107.10125-10-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
By using raw_regular_truncate() in raw_truncate(), we can now easily
support preallocation.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170613202107.10125-9-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Currently, raw_regular_truncate() is intended for setting the size of a
newly created file. However, we also want to use it for truncating an
existing file in which case only the newly added space (when growing)
should be preallocated.
This also means that if resizing failed, we should try to restore the
original file size. This is important when using preallocation.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170613202107.10125-8-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This functionality is part of raw_create() which we will be able to
reuse nicely in raw_truncate().
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170613202107.10125-7-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Variables should be declared at the start of a block, and if a certain
parameter value is not supported it may be better to return -ENOTSUP
instead of -EINVAL.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170613202107.10125-6-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
blk_truncate() itself will pass that value to bdrv_truncate(), and all
callers of blk_truncate() just set the parameter to PREALLOC_MODE_OFF
for now.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170613202107.10125-4-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
For block drivers that just pass a truncate request to the underlying
protocol, we can now pass the preallocation mode instead of aborting if
it is not PREALLOC_MODE_OFF.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170613202107.10125-3-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add a PreallocMode parameter to the bdrv_truncate() function implemented
by each block driver. Currently, we always pass PREALLOC_MODE_OFF and no
driver accepts anything else.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170613202107.10125-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Use qcow2_calc_prealloc_size() to get the required file size.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20170705125738.8777-7-stefanha@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The image creation options parsed by qcow2_create() are also needed to
implement .bdrv_measure(). Extract the parsing code, including input
validation.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20170705125738.8777-6-stefanha@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The refcount metadata size calculation is inaccurate and can produce
numbers that are too small. This is bad because we should calculate a
conservative number - one that is guaranteed to be large enough.
This patch switches the approach to a fixed point calculation because
the existing equation is hard to solve when inaccuracies are taken care
of.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20170705125738.8777-5-stefanha@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Calculating the preallocated image size will be needed to implement
.bdrv_measure(). Extract the code out into a separate function.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20170705125738.8777-4-stefanha@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Maximum size calculation is trivial for the raw format: it's just the
requested image size (because there is no metadata).
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20170705125738.8777-3-stefanha@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
We should release them here to reload on invalidate cache.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170628120530.31251-31-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Interface for removing persistent bitmap from its storage.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20170628120530.31251-28-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Store bitmaps and mark them read-only on reopening image as read-only.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170628120530.31251-21-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Store persistent dirty bitmaps in qcow2 image.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170628120530.31251-20-vsementsov@virtuozzo.com
[mreitz: Always assign ret in store_bitmap() in case of an error]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20170628120530.31251-19-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
New field BdrvDirtyBitmap.persistent means, that bitmap should be saved
by format driver in .bdrv_close and .bdrv_inactivate. No format driver
supports it for now.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20170628120530.31251-18-vsementsov@virtuozzo.com
[mreitz: Fixed indentation]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Mirror AUTO flag from Qcow2 bitmap in BdrvDirtyBitmap. This will be
needed in future, to save this flag back to Qcow2 for persistent
bitmaps.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20170628120530.31251-16-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Auto loading bitmaps are bitmaps in Qcow2, with the AUTO flag set. They
are loaded when the image is opened and become BdrvDirtyBitmaps for the
corresponding drive.
Extra data in bitmaps is not supported for now.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20170628120530.31251-12-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
It will be needed in following commits for persistent bitmaps.
If bitmap is loaded from read-only storage (and we can't mark it
"in use" in this storage) corresponding BdrvDirtyBitmap should be
read-only.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20170628120530.31251-11-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170628120530.31251-10-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add bitmap extension as specified in docs/specs/qcow2.txt.
For now, just mirror extension header into Qcow2 state and check
constraints. Also, calculate refcounts for qcow2 bitmaps, to not break
qemu-img check.
For now, disable image resize if it has bitmaps. It will be fixed later.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20170628120530.31251-9-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This is needed for the following patch, which will introduce refcounts
checking for qcow2 bitmaps.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20170628120530.31251-8-vsementsov@virtuozzo.com
[mreitz: s/inc_refcounts/qcow2_inc_refcounts_imrt/ in one more (new)
place]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add bdrv_dirty_bitmap_deserialize_ones() function, which is needed for
qcow2 bitmap loading, to handle unallocated bitmap parts, marked as
all-ones.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20170628120530.31251-7-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Make getter signature const-correct. This allows other functions with
const dirty bitmap parameter use bdrv_dirty_bitmap_granularity().
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 20170628120530.31251-6-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
While the crypto layer uses a fixed option name "key-secret",
the upper block layer may have a prefix on the options. e.g.
"encrypt.key-secret", in order to avoid clashes between crypto
option names & other block option names. To ensure the crypto
layer can report accurate error messages, we must tell it what
option name prefix was used.
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170623162419.26068-19-berrange@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Now that all encryption keys must be provided upfront via
the QCryptoSecret API and associated block driver properties
there is no need for any explicit encryption handling APIs
in the block layer. Encryption can be handled transparently
within the block driver. We only retain an API for querying
whether an image is encrypted or not, since that is a
potentially useful piece of metadata to report to the user.
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170623162419.26068-18-berrange@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This adds support for using LUKS as an encryption format
with the qcow2 file, using the new encrypt.format parameter
to request "luks" format. e.g.
# qemu-img create --object secret,data=123456,id=sec0 \
-f qcow2 -o encrypt.format=luks,encrypt.key-secret=sec0 \
test.qcow2 10G
The legacy "encryption=on" parameter still results in
creation of the old qcow2 AES format (and is equivalent
to the new 'encryption-format=aes'). e.g. the following are
equivalent:
# qemu-img create --object secret,data=123456,id=sec0 \
-f qcow2 -o encryption=on,encrypt.key-secret=sec0 \
test.qcow2 10G
# qemu-img create --object secret,data=123456,id=sec0 \
-f qcow2 -o encryption-format=aes,encrypt.key-secret=sec0 \
test.qcow2 10G
With the LUKS format it is necessary to store the LUKS
partition header and key material in the QCow2 file. This
data can be many MB in size, so cannot go into the QCow2
header region directly. Thus the spec defines a FDE
(Full Disk Encryption) header extension that specifies
the offset of a set of clusters to hold the FDE headers,
as well as the length of that region. The LUKS header is
thus stored in these extra allocated clusters before the
main image payload.
Aside from all the cryptographic differences implied by
use of the LUKS format, there is one further key difference
between the use of legacy AES and LUKS encryption in qcow2.
For LUKS, the initialiazation vectors are generated using
the host physical sector as the input, rather than the
guest virtual sector. This guarantees unique initialization
vectors for all sectors when qcow2 internal snapshots are
used, thus giving stronger protection against watermarking
attacks.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170623162419.26068-14-berrange@redhat.com
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
This converts the qcow2 driver to make use of the QCryptoBlock
APIs for encrypting image content, using the legacy QCow2 AES
scheme.
With this change it is now required to use the QCryptoSecret
object for providing passwords, instead of the current block
password APIs / interactive prompting.
$QEMU \
-object secret,id=sec0,file=/home/berrange/encrypted.pw \
-drive file=/home/berrange/encrypted.qcow2,encrypt.key-secret=sec0
The test 087 could be simplified since there is no longer a
difference in behaviour when using blockdev_add with encrypted
images for the running vs stopped CPU state.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170623162419.26068-12-berrange@redhat.com
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Instead of requiring separate input/output buffers for
encrypting data, change qcow2_encrypt_sectors() to assume
use of a single buffer, encrypting in place. The current
callers all used the same buffer for input/output already.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170623162419.26068-11-berrange@redhat.com
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
This converts the qcow driver to make use of the QCryptoBlock
APIs for encrypting image content. This is only wired up to
permit use of the legacy QCow encryption format. Users who wish
to have the strong LUKS format should switch to qcow2 instead.
With this change it is now required to use the QCryptoSecret
object for providing passwords, instead of the current block
password APIs / interactive prompting.
$QEMU \
-object secret,id=sec0,file=/home/berrange/encrypted.pw \
-drive file=/home/berrange/encrypted.qcow,encrypt.format=aes,\
encrypt.key-secret=sec0
Though note that running QEMU system emulators with the AES
encryption is no longer supported, so while the above syntax
is valid, QEMU will refuse to actually run the VM in this
particular example.
Likewise when creating images with the legacy AES-CBC format
qemu-img create -f qcow \
--object secret,id=sec0,file=/home/berrange/encrypted.pw \
-o encrypt.format=aes,encrypt.key-secret=sec0 \
/home/berrange/encrypted.qcow 64M
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170623162419.26068-10-berrange@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Instead of requiring separate input/output buffers for
encrypting data, change encrypt_sectors() to assume
use of a single buffer, encrypting in place. One current
caller uses the same buffer for input/output already
and the other two callers are easily converted to do so.
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170623162419.26068-9-berrange@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Historically the qcow & qcow2 image formats supported a property
"encryption=on" to enable their built-in AES encryption. We'll
soon be supporting LUKS for qcow2, so need a more general purpose
way to enable encryption, with a choice of formats.
This introduces an "encrypt.format" option, which will later be
joined by a number of other "encrypt.XXX" options. The use of
a "encrypt." prefix instead of "encrypt-" is done to facilitate
mapping to a nested QAPI schema at later date.
e.g. the preferred syntax is now
qemu-img create -f qcow2 -o encrypt.format=aes demo.qcow2
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170623162419.26068-8-berrange@redhat.com
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The qcow driver refuses to open images which are less than
2 bytes in size, but will happily create such images. Add
a check in the create path to avoid this discrepancy.
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170623162419.26068-5-berrange@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
When integrating the crypto support with qcow/qcow2, we don't
want to use the bare LUKS option names "hash-alg", "key-secret",
etc. We need to namespace them to match the nested QAPI schema.
e.g. "encrypt.hash-alg", "encrypt.key-secret"
so that they don't clash with any general qcow options at a later
date.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170623162419.26068-3-berrange@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The block/crypto.c defines a set of QemuOpts that provide
parameters for encryption. This will also be needed by
the qcow/qcow2 integration, so expose the relevant pieces
in a new block/crypto.h header. Some helper methods taking
QemuOpts are changed to take QDict to simplify usage in
other places.
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170623162419.26068-2-berrange@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
We are gradually moving away from sector-based interfaces, towards
byte-based. In the common case, allocation is unlikely to ever use
values that are not naturally sector-aligned, but it is possible
that byte-based values will let us be more precise about allocation
at the end of an unaligned file that can do byte-based access.
Changing the signature of the function to use int64_t *pnum ensures
that the compiler enforces that all callers are updated. For now,
the io.c layer still assert()s that all callers are sector-aligned,
but that can be relaxed when a later patch implements byte-based
block status. Therefore, for the most part this patch is just the
addition of scaling at the callers followed by inverse scaling at
bdrv_is_allocated(). But some code, particularly stream_run(),
gets a lot simpler because it no longer has to mess with sectors.
Leave comments where we can further simplify by switching to
byte-based iterations, once later patches eliminate the need for
sector-aligned operations.
For ease of review, bdrv_is_allocated() was tackled separately.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_is_allocated_above() was relying on intermediate->total_sectors,
which is a field that can have stale contents depending on the value
of intermediate->has_variable_length. An audit shows that we are safe
(we were first calling through bdrv_co_get_block_status() which in
turn calls bdrv_nb_sectors() and therefore just refreshed the current
length), but it's nicer to favor our accessor functions to avoid having
to repeat such an audit, even if it means refresh_total_sectors() is
called more frequently.
Suggested-by: John Snow <jsnow@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually moving away from sector-based interfaces, towards
byte-based. In the common case, allocation is unlikely to ever use
values that are not naturally sector-aligned, but it is possible
that byte-based values will let us be more precise about allocation
at the end of an unaligned file that can do byte-based access.
Changing the signature of the function to use int64_t *pnum ensures
that the compiler enforces that all callers are updated. For now,
the io.c layer still assert()s that all callers are sector-aligned
on input and that *pnum is sector-aligned on return to the caller,
but that can be relaxed when a later patch implements byte-based
block status. Therefore, this code adds usages like
DIV_ROUND_UP(,BDRV_SECTOR_SIZE) to callers that still want aligned
values, where the call might reasonbly give non-aligned results
in the future; on the other hand, no rounding is needed for callers
that should just continue to work with byte alignment.
For the most part this patch is just the addition of scaling at the
callers followed by inverse scaling at bdrv_is_allocated(). But
some code, particularly bdrv_commit(), gets a lot simpler because it
no longer has to mess with sectors; also, it is now possible to pass
NULL if the caller does not care how much of the image is allocated
beyond the initial offset. Leave comments where we can further
simplify once a later patch eliminates the need for sector-aligned
requests through bdrv_is_allocated().
For ease of review, bdrv_is_allocated_above() will be tackled
separately.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Change the internal
loop iteration of backups to track by bytes instead of sectors
(although we are still guaranteed that we iterate by steps that
are cluster-aligned).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Convert another internal
function (no semantic change).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Continue by converting
the public interface to backup jobs (no semantic change), including
a change to CowRequest to track by bytes instead of cluster indices.
Note that this does not change the difference between the public
interface (starting point, and size of the subsequent range) and
the internal interface (starting and end points).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Xie Changlong <xiechanglong@cmss.chinamobile.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Continue by converting an
internal structure (no semantic change), and all references to
tracking progress. Drop a redundant local variable bytes_per_cluster.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that the last user [mirror_iteration()] has converted to using
bytes, we no longer need a function to round sectors to clusters.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Change the internal
loop iteration of mirroring to track by bytes instead of sectors
(although we are still guaranteed that we iterate by steps that
are both sector-aligned and multiples of the granularity). Drop
the now-unused mirror_clip_sectors().
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Convert another internal
function, preserving all existing semantics, and adding one more
assertion that things are still sector-aligned (so that conversions
to sectors in mirror_read_complete don't need to round).
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Convert another internal
function (no semantic change), and add mirror_clip_bytes() as a
counterpart to mirror_clip_sectors(). Some of the conversion is
a bit tricky, requiring temporaries to convert between units; it
will be cleared up in a following patch.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Rather than having a void function that modifies its input
in-place as the output, change the signature to reduce a layer
of indirection and return the result.
Suggested-by: John Snow <jsnow@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Convert another internal
function (no semantic change).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Continue by converting an
internal structure (no semantic change), and all references to the
buffer size.
Add an assertion that our use of s->granularity >> BDRV_SECTOR_BITS
(necessary for interaction with sector-based dirty bitmaps, until
a later patch converts those to be byte-based) does not suffer from
truncation problems.
[checkpatch has a false positive on use of MIN() in this patch]
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Change the internal
loop iteration of committing to track by bytes instead of sectors
(although we are still guaranteed that we iterate by steps that
are sector-aligned).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Start by converting an
internal function (no semantic change).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Change the internal
loop iteration of streaming to track by bytes instead of sectors
(although we are still guaranteed that we iterate by steps that
are sector-aligned).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
stream_complete() skips the work of rewriting the backing file if
the job was cancelled, if data->reached_end is false, or if there
was an error detected (non-zero data->ret) during the streaming.
But note that in stream_run(), data->reached_end is only set if the
loop ran to completion, and data->ret is only 0 in two cases:
either the loop ran to completion (possibly by cancellation, but
stream_complete checks for that), or we took an early goto out
because there is no bs->backing. Thus, we can preserve the same
semantics without the use of reached_end, by merely checking for
bs->backing (and logically, if there was no backing file, streaming
is a no-op, so there is no backing file to rewrite).
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Start by converting an
internal function (no semantic change).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Upcoming patches are going to switch to byte-based interfaces
instead of sector-based. Even worse, trace_backup_do_cow_enter()
had a weird mix of cluster and sector indices.
The trace interface is low enough that there are no stability
guarantees, and therefore nothing wrong with changing our units,
even in cases like trace_backup_do_cow_skip() where we are not
changing the trace output. So make the tracing uniformly use
bytes.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The user interface specifies job rate limits in bytes/second.
It's pointless to have our internal representation track things
in sectors/second, particularly since we want to move away from
sector-based interfaces.
Fix up a doc typo found while verifying that the ratelimit
code handles the scaling difference.
Repetition of expressions like 'n * BDRV_SECTOR_SIZE' will be
cleaned up later when functions are converted to iterate over
images by bytes rather than by sectors.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
According to specification:
"'MSWIN4.1' is the recommanded setting, because it is the setting least likely
to cause compatibility problems. If you want to put something else in here,
that is your option, but the result may be that some FAT drivers might not
recognize the volume."
Specification: "FAT: General overview of on-disk format" v1.03, page 9
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Specification: "FAT: General overview of on-disk format" v1.03, page 23
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
FAT12/FAT16 root directory is two sectors in size, which allows only 512 directory entries.
Prevent QEMU startup if too much files exist, instead of overflowing root directory.
Also introduce variable root_entries, which will be required for FAT32.
Fixes: https://bugs.launchpad.net/qemu/+bug/1599539/comments/4
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
More specifically:
- try without numeric-tail only if LFN didn't have invalid short chars
- start at ~1 (instead of ~0)
- handle case if numeric tail is more than one char (ie > 10)
Windows 9x Scandisk doesn't see anymore mismatches between short file names and
long file names for non-ASCII filenames.
Specification: "FAT: General overview of on-disk format" v1.03, page 31
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
More specifically, create short name from filename and change blacklist of
invalid chars to whitelist of valid chars.
Windows 9x also now correctly see long file names of filenames containing a space,
but Scandisk still complains about mismatch between SFN and LFN.
[kwolf: Build fix for this intermediate patch (it included declarations
for variables that are only used in the next patch) ]
Specification: "FAT: General overview of on-disk format" v1.03, pages 30-31
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Assume that input filename is encoded as UTF-8, so correctly create UTF-16 encoding.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
readdir() doesn't always return . and .. entries at first and in that order.
This leads to not creating them at first in the directory, which raises some
errors on file system checking utilities like MS-DOS Scandisk.
Specification: "FAT: General overview of on-disk format" v1.03, page 25
Fixes: https://bugs.launchpad.net/qemu/+bug/1599539
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Specification: "FAT: General overview of on-disk format" v1.03, pages 11-13
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
- offset_to_bootsector is the number of sectors up to FAT bootsector
- offset_to_fat is the number of sectors up to first File Allocation Table
- offset_to_root_dir is the number of sectors up to root directory sector
Replace first_sectors_number - 1 by offset_to_bootsector.
Replace first_sectors_number by offset_to_fat.
Replace faked_sectors by offset_to_rootdir.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
MODE_FAKED and MODE_RENAMED are not and were never used.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This was a complete mess. On 2299 indented lines:
- 1329 were with spaces only
- 617 with tabulations only
- 353 with spaces and tabulations
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
- bs->total_sectors is the number of sectors of the whole disk
- s->sector_count is the number of sectors of the FAT partition
This fixes the following assert in qemu-img map:
qemu-img.c:2641: get_block_status: Assertion `nb_sectors' failed.
This also fixes an infinite loop in qemu-img convert.
Fixes: 4480e0f924
Fixes: https://bugs.launchpad.net/qemu/+bug/1599539
Cc: qemu-stable@nongnu.org
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Without a passthrough status of BDRV_BLOCK_RAW, anything wrapped by
blkdebug appears 100% allocated as data. Better is treating it the
same as the underlying file being wrapped.
Update iotest 177 for the new expected output.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The lone caller that cares about a return of BDRV_BLOCK_RAW
(namely, io.c:bdrv_co_get_block_status) completely replaces the
return value, so there is no point in passing BDRV_BLOCK_DATA.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We document that *file is valid if the return is not an error and
includes BDRV_BLOCK_OFFSET_VALID, but forgot to obey this contract
when a driver (such as blkdebug) lacks a callback. Messed up in
commit 67a0fd2 (v2.6), when we added the file parameter.
Enhance qemu-iotest 177 to cover this, using a sequence that would
print garbage or even SEGV, because it was dererefencing through
uninitialized memory. [The resulting test output shows that we
have less-than-ideal block status from the blkdebug driver, but
that's a separate fix coming up soon.]
Setting *file on all paths that return BDRV_BLOCK_OFFSET_VALID is
enough to fix the crash, but we can go one step further: always
setting *file, even on error, means that a broken caller that
blindly dereferences file without checking for error is now more
likely to get a reliable SEGV instead of randomly acting on garbage,
making it easier to diagnose such buggy callers. Adding an
assertion that file is set where expected doesn't hurt either.
CC: qemu-stable@nongnu.org
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When attaching the NBD QIOChannel to an AioContext, the TLS channel should
be used, not the underlying socket channel. This is because, trivially,
the TLS channel will be the one that we read/write to and thus the one
that will get the qio_channel_yield() call.
Fixes: ff82911cd3
Cc: qemu-stable@nongnu.org
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Tested-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When we have a BDS with unallocated clusters, but asking the status
of its underlying bs->file or backing layer encounters an end-of-file
condition, we know that the rest of the unallocated area will read as
zeroes. However, pre-patch, this required two separate calls to
bdrv_get_block_status(), as the first call stops at the point where
the underlying file ends. Thanks to BDRV_BLOCK_EOF, we can now widen
the results of the primary status if the secondary status already
includes BDRV_BLOCK_ZERO.
In turn, this fixes a TODO mentioned in iotest 154, where we can now
see that all sectors in a partial cluster at the end of a file read
as zero when coupling the shorter backing file's status along with our
knowledge that the remaining sectors came from an unallocated cluster.
Also, note that the loop in bdrv_co_get_block_status_above() had an
inefficent exit: in cases where the active layer sets BDRV_BLOCK_ZERO
but does NOT set BDRV_BLOCK_ALLOCATED (namely, where we know we read
zeroes merely because our unallocated clusters lie beyond the backing
file's shorter length), we still ended up probing the backing layer
even though we already had a good answer.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20170505021500.19315-3-eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Just as the block layer already sets BDRV_BLOCK_ALLOCATED as a
shortcut for subsequent operations, there are also some optimizations
that are made easier if we can quickly tell that *pnum will advance
us to the end of a file, via a new BDRV_BLOCK_EOF which gets set
by the block layer.
This just plumbs up the new bit; subsequent patches will make use
of it.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20170505021500.19315-2-eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
uri_parse(...)->scheme may be NULL. In fact, probably every field may be
NULL, and the callers do test this for all of the other fields but not
for scheme (except for block/gluster.c; block/vxhs.c does not access
that field at all).
We can easily fix this by using g_strcmp0() instead of strcmp().
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170613205726.13544-1-mreitz@redhat.com
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The bs->exact_filename field may not be sufficient to store the full
blkverify node filename. In this case, we should not generate a filename
at all instead of an unusable one.
Cc: qemu-stable@nongnu.org
Reported-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170613172006.19685-3-mreitz@redhat.com
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The bs->exact_filename field may not be sufficient to store the full
blkdebug node filename. In this case, we should not generate a filename
at all instead of an unusable one.
Cc: qemu-stable@nongnu.org
Reported-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170613172006.19685-2-mreitz@redhat.com
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Change the 'int count' parameter in *pwrite_zeros, *pdiscard related
functions (and some others) to 'int bytes', as they both refer to bytes.
This helps with code legibility.
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Message-id: 20170609101808.13506-1-el13635@mail.ntua.gr
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
All functions that are marked coroutine_fn can directly call the
bdrv_co_* version of functions instead of going through the wrapper.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Now that we stay in coroutine context for the whole request when doing
reads or writes, we can add coroutine_fn annotations to many functions
that can do I/O or yield directly.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
This fixes the last place where we degraded from AIO to actual blocking
synchronous I/O requests. Putting it into a coroutine means that instead
of blocking, the coroutine simply yields while doing I/O.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Now that we process a request in the same coroutine from beginning to
end and don't drop out of it any more, we can look like a proper
coroutine-based driver and simply call qed_aio_next_io() and get a
return value from it instead of spawning an additional coroutine that
reenters the parent when it's done.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
