Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
[Actually, we should report it only if discard_granularity is nonzero.
Older SBC drafts assigned 0 to thin provisioning and 1 to thick
(resource-provisioned, they call it). Newer drafts assign respectively
1 and 2 - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This was added in SBC r26 in place of the reserved bits that were
present up to that version.
It is the same as WRITE_SAME_16 as far as QEMU is concerned.
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To force unit access, add a flush operation after the actual write.
WRITE AND VERIFY commands always flush according to SBC, so do it
even though we do not perform the reread.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
First scsi_flush_complete, like scsi_dma_complete, is always called with
an active AIOCB.
Second, always test for "ret < 0" to check for errors.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently QEMU passes the qdev device id to the guest in an ASCII-string
designator in page 0x83. While this is fine, it does not match what
real hardware does; usually the ASCII-string designator there hosts
another copy of the serial number (there can be other designators,
for example with a world-wide name). Do the same for QEMU SCSI
disks.
ATAPI does not support VPD pages, so it does not matter there.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This commit is more or less obvious. What it caused is less obvious:
SCSI CD drives failed to eject under Linux, though for example the
"change" command worked okay. This happens because of the autoclose
option in the Linux CD-ROM driver.
The actual chain of events is quite complex and somehow involves
udev helpers; the actual command that matters is READ TOC, though
honestly it's not really clear to me how because it should always be
invoked after autoclose, not before.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* qmp/queue/qmp:
qmp: add DEVICE_TRAY_MOVED event
ide: drop ide_tray_state_post_load()
block: Don't call bdrv_eject() if the tray state didn't change
block: bdrv_eject(): Make eject_flag a real bool
block: Rename bdrv_mon_event() & BlockMonEventAction
It's not needed. Besides we can then assume that bdrv_eject() is
only called when there's a tray state change, which is useful to
the DEVICE_TRAY_MOVED event (going to be added in a future
commit).
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
They are QMP events, not monitor events. Rename them accordingly.
Also, move bdrv_emit_qmp_error_event() up in the file. A new event will
be added soon and it's good to have them next each other.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Replace device_init() with generalized type_init().
While at it, unify naming convention: type_init([$prefix_]register_types)
Also, type_init() is a function, so add preceding blank line where
necessary and don't put a semicolon after the closing brace.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Cc: malc <av1474@comtv.ru>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This was done in a mostly automated fashion. I did it in three steps and then
rebased it into a single step which avoids repeatedly touching every file in
the tree.
The first step was a sed-based addition of the parent type to the subclass
registration functions.
The second step was another sed-based removal of subclass registration functions
while also adding virtual functions from the base class into a class_init
function as appropriate.
Finally, a python script was used to convert the DeviceInfo structures and
qdev_register_subclass functions to TypeInfo structures, class_init functions,
and type_register_static calls.
We are almost fully converted to QOM after this commit.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Limit the return value (corresponding to the length of the buffer to be
DMAed back to the intiator) to the value in req->cmd.xfer, which is the
amount of data that the initiator expects. Eliminate now-duplicate code
that does this guarding in the functions for individual commands.
Without this, the SCRIPTS code in the emulated LSI device eventually
raises a DMA interrupt for a data overrun when an INQUIRY command whose
buflen exceeds req->cmd.xfer is processed. It's the responsibility of
the client to provide a request buffer and allocation length that are
large enough for the result of the command.
Signed-off-by: Thomas Higdon <thigdon@akamai.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Replace
error_report("DEVICE-NAME: MESSAGE");
by just
error_report("MESSAGE");
in block device init functions.
DEVICE-NAME is bogus in some cases: it's "scsi-disk" for device
scsi-hd and scsi-cd, "virtio-blk-pci" for virtio-blk-s390, and
"usb-msd" for usb-storage.
There is no real need to put a device name in the message, because
error_report() points to the offending command line option already:
$ qemu-system-x86_64 --nodefaults --enable-kvm -vnc :0 -S -monitor stdio -usb -device virtio-blk-pci
upstream-qemu: -device virtio-blk-pci: virtio-blk-pci: drive property not set
upstream-qemu: -device virtio-blk-pci: Device 'virtio-blk-pci' could not be initialized
And for a monitor command, it's obvious anyway:
$ qemu-system-x86_64 --nodefaults --enable-kvm -vnc :0 -S -monitor stdio -usb
(qemu) device_add virtio-blk-pci
virtio-blk-pci: drive property not set
Device 'virtio-blk-pci' could not be initialized
Reported-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Initially done with the following semantic patch:
@ rule1 @
expression E;
statement S;
@@
E =
(
bdrv_aio_readv
| bdrv_aio_writev
| bdrv_aio_flush
| bdrv_aio_discard
| bdrv_aio_ioctl
)
(...);
(
- if (E == NULL) { ... }
|
- if (E)
{ <... S ...> }
)
which however missed the occurrence in block/blkverify.c
(as it should have done), and left behind some unused
variables.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
CD burning messes up the state of the host page cache and host block
device. Just pass all operations down to the device, even though that
might have slightly worse performance. Everything else just is not
reliable in combination with burning.
Reported-by: Thomas Schmitt <scdbackup@gmx.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This will let scsi-block/scsi-generic report progress on long
operations.
Reported-by: Thomas Schmitt <scdbackup@gmxbackup.net>
Tested-by: Thomas Schmitt <scdbackup@gmxbackup.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reported-by: Thomas Schmitt <scdbackup@gmx.net>
Tested-by: Thomas Schmitt <scdbackup@gmx.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add more commands and their names, and remove SEEK(6) which is obsolete.
Instead, use SET_CAPACITY which is still in SSC.
Tested-by: Thomas Schmitt <scdbackup@gmx.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Old operating systems rely on correct geometry to convert from CHS
addresses to LBA. Providing correct data is necessary for them to boot.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The pre-1.0 firmware path for SCSI devices already included the LUN
using the suffix argument to add_boot_device_path. I missed that when
making channel and LUN customizable. Avoid that it is included twice, and
convert the colons to commas for consistency with other kinds of devices
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
scsi-block is a new device that supports device passthrough of Linux
block devices (i.e. /dev/sda, not /dev/sg0). It uses SG_IO for commands
other than I/O commands, and regular AIO read/writes for I/O commands.
Besides being simpler to configure (no mapping required to scsi-generic
device names), this removes the need for a large bounce buffer and,
in the future, will get scatter/gather support for free from scsi-disk.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The request restart mechanism is generic and could be reused for
scsi-generic. In the meanwhile, pushing it to SCSIDevice avoids
that scsi_dma_restart_bh looks at SCSIGenericReqs when working on
a scsi-block device.
The code is the same that is already in hw/scsi-disk.c, with
the type flags replaced by req->cmd.mode and a more generic way to
requeue SCSI_XFER_NONE commands.
I also added a missing call to qemu_del_vm_change_state_handler.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In some cases a request may be canceled before the completion callback
runs. Keep a reference to the request between starting an AIO operation
and the corresponding scsi_req_cancel or scsi_*_complete.
When a request has to be retried, the request can be dropped because
scsi_dma_restart_bh only looks at requests that are enqueued. As such,
they always have at least a reference.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This will let scsi-block choose between passthrough and emulation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Also delete a stale occurrence of SCSIReqOps inside SCSIDeviceInfo.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The field is only in scsi-disk for now. Moving it up to SCSIDevice makes
it easier to reuse the scsi-generic reqops elsewhere.
At the same time, make scsi-generic get max_lba from snooped READ CAPACITY
commands as well.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Set s->removable, s->qdev.blocksize and s->qdev.type in the callers
of scsi_initfn.
With this in place, s->qdev.type is allowed, and we can just reuse it
as the first byte in VPD data (just like we do in standard INQUIRY data).
Also set s->removable is set consistently and we can use it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This field is redundant, and having it makes it more complicated
to share reqops between the upcoming scsi-block and scsi-generic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Same as for scsi-generic, avoid duplication even if it causes longer
lines.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Flush does not go anymore through scsi_disk_emulate_command.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Tested by the Windows Logo Kit SCSI Compliance test. From SBC-3, paragraph
5.25: "The LOGICAL BLOCK ADDRESS field shall be set to zero if the PMI
bit is set to zero. If the PMI bit is set to zero and the LOGICAL BLOCK
ADDRESS field is not set to zero, then the device server shall terminate
the command with CHECK CONDITION status with the sense key set to ILLEGAL
REQUEST and the additional sense code set to INVALID FIELD IN CDB".
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds support for media change notification via the GET EVENT STATUS
NOTIFICATION command, used by Linux versions 2.6.38 and newer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds to scsi-disk the missing mode page 0x01 for both disk
and CD-ROM drives, and mode page 0x0e for CD drives only.
A few offsets were wrong in atapi.c. Also change the 2Ah mode page to
expose DVD media read capabilities in the IDE cdrom. This lets you run
dvd+rw-mediainfo on the virtual DVD drives.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A small refactoring of the MODE SENSE implementation in scsi-disk.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds a few stub implementations for MMC commands to
scsi-disk, to be filled in later in the series. It also adds to
scsi-defs.h constants for commands implemented by ide/atapi.c,
when missing.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
