Pull the AHCI state structure out into the header. This allows
other containers to access the struct. This is required to add
the device to modern SoC containers.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
pci_piix3_xen_ide_unplug should completely unhook the unplugged
IDEDevice from the corresponding BlockBackend, otherwise the next call
to release_drive will try to detach the drive again.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
There are likely others that could be updated, but we'll
go with a light touch for 2.4 for now.
Without the Unsigned specifier, this shifts bits into the
signed bit, which makes clang unhappy and could cause
unwanted behavior.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1437501721-24495-1-git-send-email-jsnow@redhat.com
Commit bd4214fc dropped TRIM support by mistake. Given it is still
advertised to the host when using a drive with discard=on, this cause
the IDE bus to hang when the host issues a TRIM command.
This patch fixes that by re-adding the TRIM code, ported to the new
new DMA implementation.
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: John Snow <jsnow@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-id: 1438198068-32428-1-git-send-email-aurelien@aurel32.net
Signed-off-by: John Snow <jsnow@redhat.com>
This is additional hardening against an end_transfer_func that fails to
clear the DRQ status bit. The bit must be unset as soon as the PIO
transfer has completed, so it's better to do this in a central place
instead of duplicating the code in all commands (and forgetting it in
some).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
The command must be completed on all code paths. START STOP UNIT with
pwrcnd set should succeed without doing anything.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
If the end_transfer_func of a command is called because enough data has
been read or written for the current PIO transfer, and it fails to
correctly call the command completion functions, the DRQ bit in the
status register and s->end_transfer_func may remain set. This allows the
guest to access further bytes in s->io_buffer beyond s->data_end, and
eventually overflowing the io_buffer.
One case where this currently happens is emulation of the ATAPI command
START STOP UNIT.
This patch fixes the problem by adding explicit array bounds checks
before accessing the buffer instead of relying on end_transfer_func to
function correctly.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
The AHCI spec requires that the HBA sets the ICC bits to zero after the
ICC change is done. Since we don't do any ICC change, force the bits to
zero all the time.
This fixes delays with some OSs (e.g. OpenBSD) waiting for the ICC bits
to change to 0.
Signed-off-by: Stefan Fritsch <sf@sfritsch.de>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: E1ZFpg7-00027N-HW@eru.sfritsch.de
Signed-off-by: John Snow <jsnow@redhat.com>
The CD-ROM signature is 0xeb140101, not 0xeb140000.
Without this change OVMF/Duet runs into a timeout trying
to detect a SATA cdrom.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 1436219392-31915-2-git-send-email-jsnow@redhat.com
There are two things to fix here:
The first one is subtle: the PxSACT register in the AHCI HBA has different
semantics from the field it is shadowing, the ACT field in the
Set Device Bits FIS.
In the HBA register, PxSACT acts as a bitfield indicating outstanding
NCQ commands where a set bit indicates a pending NCQ operation. The FIS
field however operates as an RWC register update to PxSACT, where a set
bit indicates a *successfully* completed command.
Correct the FIS semantics. At the same time, move the "clear finished"
action to the SDB FIS generation instead of the register read to mimick
how the other shadow registers work, which always just report the last
reported value from a FIS, and not the most current values which may
not have been reported by a FIS yet.
Lastly and more simply, SATA 3.2 section 13.6.4.2 (and later sections)
all specify that the Interrupt bit for the SDB FIS should always be set
to one for NCQ commands. That's currently the only time we generate this
FIS, so set it on all the time.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-16-git-send-email-jsnow@redhat.com
The Register D2H FIS should copy the current values of
the registers instead of just parroting back the same
values the guest sent back to it.
In this case, the SECTOR COUNT variables are actually
not generally meaningful in terms of standard commands
(See ATA8-AC3 Section 9.2 Normal Outputs), so it actually
probably doesn't matter what we put in here.
Meanwhile, we do need to use the Register update FIS from
the NCQ pathways (in error cases), so getting rid of
references to cur_cmd here is a win for AHCI concurrency.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-14-git-send-email-jsnow@redhat.com
Migrate the NCQ queue. This is solely for the benefit of halted commands,
since anything else should have completed and had any relevant status
flushed to the HBA registers already.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-13-git-send-email-jsnow@redhat.com
cur_cmd is an internal bookmark that points to the
current AHCI Command Header being processed by the
AHCI state machine. With NCQ needing to occasionally
rely on some of the same AHCI helpers, we cannot use
cur_cmd and will need to grab explicit pointers instead.
In an attempt to begin relying on the cur_cmd pointer
less, add a helper to let us specifically get the pointer
to the command header of particular interest.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-12-git-send-email-jsnow@redhat.com
While the rest of the AHCI device can rely on a single bookmarked
pointer for the AHCI Command Header currently being processed, NCQ
is asynchronous and may have many commands in flight simultaneously.
Add a cmdh pointer to the ncq_tfs object and make the sglist prepare
function take an AHCICmdHeader pointer so we can be explicit about
where we'd like to build SGlists from.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-11-git-send-email-jsnow@redhat.com
uint16_t isn't enough to hold the real sector count, since a value of
zero implies a full 64K sectors, so we need a uint32_t here.
We *could* cheat and pretend that this value is 0-based and fit it in
a uint16_t, but I'd rather waste 2 bytes instead of a future dev's
10 minutes when they forget to +1/-1 accordingly somewhere.
See SATA 3.2, section 13.6.4.1 "READ FPDMA QUEUED".
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-9-git-send-email-jsnow@redhat.com
Handle NCQ failures for cases where we want to halt the VM on IO errors.
Upon a VM state change, retry the halted NCQ commands.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-7-git-send-email-jsnow@redhat.com
When we add werror=stop or rerror=stop support to NCQ,
we'll want to take a codepath where we don't actually
complete the command, so factor that out into a new routine.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-6-git-send-email-jsnow@redhat.com
Split off execute_ncq_command so that we can call
it separately later if we desire.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-5-git-send-email-jsnow@redhat.com
We already checked this in the handle_cmd phase, so just
change this to an assertion and simplify the error logic.
(Also, fix the switch indent, because checkpatch.pl yelled.)
((Sorry for churn.))
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-4-git-send-email-jsnow@redhat.com
For migration and werror=stop/rerror=stop resume purposes,
it will be convenient to have the command handy inside of
ncq_tfs.
Eventually, we'd like to avoid reading from the FIS entirely
after the initial read, so this is a byte (hah!) sized step
in that direction.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-3-git-send-email-jsnow@redhat.com
prepare_buf should not always grab as many descriptors
as it can, sometimes it should self-limit.
For example, an NCQ transfer of 1 sector with a PRDT that
describes 4GiB of data should not copy 4GiB of data, it
should just transfer that first 512 bytes.
PIO is not affected, because the dma_buf_rw dma helpers
already have a byte limit built-in to them, but DMA/NCQ
will exhaust the entire list regardless of requested size.
AHCI 1.3 specifies in section 6.1.6 Command List Underflow that
NCQ is not required to detect underflow conditions. Non-NCQ
pathways signal underflow by writing to the PRDBC field, which
will already occur by writing the actual transferred byte count
to the PRDBC, signaling the underflow.
Our NCQ pathways aren't required to detect underflow, but since our DMA
backend uses the size of the PRDT to determine the size of the transer,
if our PRDT is bigger than the transaction (the underflow condition) it
doesn't cost us anything to detect it and truncate the PRDT.
This is a recoverable error and is not signaled to the guest, in either
NCQ or normal DMA cases.
For BMDMA, the existing pathways should see no guest-visible difference,
but any bytes described in the overage will no longer be transferred
before indicating to the guest that there was an underflow.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-2-git-send-email-jsnow@redhat.com
This value should not be size-corrected, 0 sectors does not imply
1 sector(s). This is just debug information, but it's misleading!
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-8-git-send-email-jsnow@redhat.com
Most of the time, these bits can be safely ignored. For the purposes
of debugging however, it's nice to know that they're not being used.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-7-git-send-email-jsnow@redhat.com
There's no real reason to have it bundled together, and this way
is a little nicer to follow if you have the AHCI spec pulled up.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-6-git-send-email-jsnow@redhat.com
Don't attempt the NCQ transfer if the PRDT we were given is not big
enough to perform the entire transfer.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-5-git-send-email-jsnow@redhat.com
Set some appropriate error bits for NCQ for us.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-4-git-send-email-jsnow@redhat.com
Trivial cleanup that I didn't want to tack-on to anything else.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-3-git-send-email-jsnow@redhat.com
Several fields of the NCQFIS structure are ambiguously named. This patch
clarifies the intended (if unsupported) usage of the NCQ fields to aid
in creating more meaningful debug messages through the NCQ codepaths.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-2-git-send-email-jsnow@redhat.com
The only guidance the AHCI specification gives on memory access is:
"Register accesses shall have a maximum size of 64-bits; 64-bit access
must not cross an 8-byte alignment boundary."
I interpret this to mean that aligned or unaligned 1, 2 and 4 byte
accesses should work, as well as aligned 8 byte accesses.
In practice, a real Q35/ICH9 responds to 1, 2, 4 and 8 byte reads
regardless of alignment. Windows 7 can be observed making 1 byte
reads to the middle of 32 bit registers to fetch error codes.
Introduce a wrapper to support unaligned accesses to AHCI.
This wrapper will support aligned 8 byte reads, but will make
no effort to support unaligned 8 byte reads, which although they
will work on real hardware, are not guaranteed to work and do
not appear to be used by either Windows or Linux.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1434470575-21625-2-git-send-email-jsnow@redhat.com
In particular, don't include it into headers.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
We create optional sections with this patch. But we already have
optional subsections. Instead of having two mechanism that do the
same, we can just generalize it.
For subsections we just change:
- Add a needed function to VMStateDescription
- Remove VMStateSubsection (after removal of the needed function
it is just a VMStateDescription)
- Adjust the whole tree, moving the needed function to the corresponding
VMStateDescription
Signed-off-by: Juan Quintela <quintela@redhat.com>
Version: GnuPG v1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=TBeO
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jnsnow/tags/ide-pull-request' into staging
# gpg: Signature made Fri Jun 5 20:59:07 2015 BST using RSA key ID AAFC390E
# gpg: Good signature from "John Snow (John Huston) <jsnow@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: FAEB 9711 A12C F475 812F 18F2 88A9 064D 1835 61EB
# Subkey fingerprint: F9B7 ABDB BCAC DF95 BE76 CBD0 7DEF 8106 AAFC 390E
* remotes/jnsnow/tags/ide-pull-request:
macio: remove remainder_len DBDMA_io property
macio: update comment/constants to reflect the new code
macio: switch pmac_dma_write() over to new offset/len implementation
macio: switch pmac_dma_read() over to new offset/len implementation
fdc-test: Test state for existing cases more thoroughly
fdc: Fix MSR.RQM flag
fdc: Disentangle phases in fdctrl_read_data()
fdc: Code cleanup in fdctrl_write_data()
fdc: Use phase in fdctrl_write_data()
fdc: Introduce fdctrl->phase
fdc: Rename fdctrl_set_fifo() to fdctrl_to_result_phase()
fdc: Rename fdctrl_reset_fifo() to fdctrl_to_command_phase()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since the block alignment code is now effectively independent of the DMA
implementation, this variable is no longer required and can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1433455177-21243-5-git-send-email-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
With the offset/len functions taking care of all of the alignment mapping
in isolation from the DMA tranasaction, many comments are now unnecessary.
Remove these and tidy up a few constants at the same time.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1433455177-21243-4-git-send-email-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
In particular, this fixes a bug whereby chains of overlapping head/tail chains
would incorrectly write over each other's remainder cache. This is the access
pattern used by OS X/Darwin and fixes an issue with a corrupt Darwin
installation in my local tests.
While we are here, rename the DBDMA_io struct property remainder to
head_remainder for clarification.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1433455177-21243-3-git-send-email-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
For better handling of unaligned block device accesses.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1433455177-21243-2-git-send-email-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
valgrind complains about:
==16447== 16 bytes in 2 blocks are definitely lost in loss record 1,304 of 3,310
==16447== at 0x4C2845D: malloc (in /usr/lib64/valgrind/vgpreload_memcheck-amd64-linux.so)
==16447== by 0x2E4FD7: malloc_and_trace (vl.c:2546)
==16447== by 0x64C770E: g_malloc (in /usr/lib64/libglib-2.0.so.0.3600.3)
==16447== by 0x36FB47: qemu_extend_irqs (irq.c:55)
==16447== by 0x36FBD3: qemu_allocate_irqs (irq.c:64)
==16447== by 0x3B4B44: bmdma_init (pci.c:464)
==16447== by 0x3B547B: pci_piix_init_ports (piix.c:144)
==16447== by 0x3B55D2: pci_piix_ide_realize (piix.c:164)
==16447== by 0x3EAEC6: pci_qdev_realize (pci.c:1790)
==16447== by 0x36C685: device_set_realized (qdev.c:1058)
==16447== by 0x47179E: property_set_bool (object.c:1514)
==16447== by 0x470098: object_property_set (object.c:837)
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This continues the IOMMU fix from 2.3, where we should not attempt
to remap the CLB or FIS RX buffers if the AHCI device is currently
running.
The same applies to migration: keep our mitts off these registers
unless the device is supposed to be on.
Does not impact backwards compatibility for the AHCI device.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1431470173-30847-2-git-send-email-jsnow@redhat.com
Similarly switch the macio IDE routines over to use the new function and
tidy-up the remaining code as required.
[Maintainer edit: printf format codes adjusted for 32/64bit. --js]
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: John Snow <jsnow@redhat.com>
Message-id: 1425939893-14404-3-git-send-email-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
This considerably helps simplify the complexity of the macio read routines and
by switching macio CDROM accesses to use the new code, fixes the issue with
the CDROM device being detected intermittently by Darwin/OS X.
[Maintainer edit: printf format codes adjusted for 32/64bit. --js]
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ailande.co.uk>
Acked-by: John Snow <jsnow@redhat.com>
Message-id: 1425939893-14404-2-git-send-email-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
Lift the flag preventing the migration of the ICH9/AHCI devices.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 1430417242-11859-5-git-send-email-jsnow@redhat.com
IDE PIO data must be written, for example, at 0x1f0. You cannot
do word or dword writes to 0x1f1..0x1f3 to access the data register.
Adjust the ide_portio_list accordingly.
Cc: John Snow <jsnow@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Many bits in the CMD register are supposed to be strictly read-only.
We should not be deleting them on every write.
As a side-effect: pay explicit attention to when a guest marks off
the FIS Receive or Start bits, and disable the status bits ourselves,
instead of letting them implicitly fall off.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1426283454-15590-3-git-send-email-jsnow@redhat.com
The FIS Receive Buffer and Command List Buffer pointers
should not be edited while the FIS receive engine or
Command Receive engines are running.
Currently, we attempt to re-map the buffers every time they
are adjusted, but while the AHCI engines are off, these registers
may contain stale values, so we should not attempt to re-map these
values until the engines are reactivated.
Reported-by: Jordan Hargrave <jharg93@gmail.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1426283454-15590-2-git-send-email-jsnow@redhat.com
This does not bother DMA, because DMA generally transfers
the entire SGList in one shot if it can.
PIO, on the other hand, tries to transfer just one sector
at a time, and will make multiple visits to the sglist
to fetch memory addresses.
Fix the memory address calculaton when we have an offset
by moving the offset addition OUTSIDE of the le64_to_cpu
calculation.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Message-id: 1426811056-2202-4-git-send-email-jsnow@redhat.com
Similar to the cmd_write_pio fix, update the nsector count and
ide sector before we invoke ide_transfer_start.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Message-id: 1426811056-2202-3-git-send-email-jsnow@redhat.com
We need to adjust the sector being written to
prior to calling ide_transfer_start, otherwise
we'll write to the same sector again.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Message-id: 1426811056-2202-2-git-send-email-jsnow@redhat.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hlbC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block patches for 2.3
# gpg: Signature made Tue Mar 10 13:03:17 2015 GMT using RSA key ID C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
* remotes/kevin/tags/for-upstream: (73 commits)
MAINTAINERS: Add jcody as blockjobs, block devices maintainer
iotests: add O_DIRECT alignment probing test
block/raw-posix: fix launching with failed disks
MAINTAINERS: Add jsnow as IDE maintainer
sheepdog: Fix misleading error messages in sd_snapshot_create()
Add testcase for scsi-hd devices without drive property
scsi-hd: fix property unset case
block/vdi: Add locking for parallel requests
iotests: Drop vpc from 004's and 104's format list
iotests: Remove 006
iotests: Fix 051's reference output
virtio-blk: Remove the stale FIXME comment
tests: Check QVIRTIO_F_ANY_LAYOUT flag in virtio-blk test
libqos: Solve bug in interrupt checking when using MSIX in virtio-pci.c
sheepdog: fix confused return values
qtest/ahci: add fragmented dma test
qtest/ahci: Add PIO and LBA48 tests
qtest/ahci: Add DMA test variants
libqos/ahci: add ahci command helpers
qtest/ahci: Add a macro bootup routine
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the AHCI HBA device is migrated, all of the information that
led to the request being created is stored in the AHCIDevice
structures, except for pointers into guest data where return
information needs to be stored.
The "cur_cmd" field is usually responsible for this.
To rebuild the cur_cmd pointer post-migration, we can utilize
the busy_slot index to figure out where the command header
we are still processing is.
This allows a machine in a halted state from rerror=stop or
werror=stop to be migrated and resume operations without issue.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-17-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is easy, since start_dma already restarts processing from the
beginning of the PRDT.
Migration is also easy to cover; the comment about busy_slot is
wrong, busy_slot will only be set if there is an error. In this
case we have nothing to do really. The core IDE code will restart
the operation and command list processing will proceed after the
erroring command has been completed.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-16-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Amazingly, we weren't doing this before.
Make sure we migrate the IDEState structure that belongs to
the AHCIDevice.IDEBus structure during migrations.
No version numbering changes because AHCI is not officially
migratable (and we can all see with good reason why) so we
do not impact any official builds by altering the stream and
leaving it at version 1.
This fixes the rerror=stop/werror=stop test case where we wish
to migrate a halted job. Previously, the error code would not
migrate, so even if the job completed successfully, AHCI would
report an error because it would still have the placeholder
error code from initialization time.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-15-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-14-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-13-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Resetting the io_buffer_index to 0 is commonized,
with the exception of the case within ide_atapi_cmd_reply,
where we need to reset this index to 0 prior to the
ide_atapi_cmd_reply_end call.
Note that not all calls to ide_atapi_cmd_reply_end
expect the index to be 0, so setting it there is
not appropriate.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-12-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This only breaks backwards migration compatibility if the bus is in
an error state. It is in principle possible to avoid this by making
two subsections (one for version 1, and one for version 2, but with
the same name) with different "_needed" callbacks. The v1 callback would
return true if error_status != 0 and the bus is PATA; the v2 callback
would return true if error_status != 0 and the bus is AHCI.
Forward migration keeps working.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-11-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This moves more common restarting logic to the core IDE code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-10-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Start moving the initial state of the current request to IDEBus, so that
AHCI can use it. The set_unit callback is not used anymore once this is
done.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-9-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With restarts now handled by ide_restart_cb and
the IDEDMAOps.restart_dma() member, remove the old
restart_cb callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-8-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With BMDMA specific excised from the restart functions,
create a HBA-agnostic restart callback to be shared
between the different HBAs.
Change the callback registered with the vmstate_change
handler to always point to ide_restart_cb instead of
relying on the IDEDMAOps.restart_cb() member.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-7-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Pass the containing IDEBus to the restart_cb instead
of the more specific BMDMAState child.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-6-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Whenever an error stops the VM, ide_handle_rw_error does
"s->bus->dma->unit = s->unit". So we can just use
idebus_active_if.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-5-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A helper is added that registers the IDEDMAOp .restart_cb()
via qemu_add_vm_change_state_handler instead of requiring
each HBA to register the callback themselves.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds the restart_dma callback and adjusts
the ide_restart_dma function to utilize this callback
to call the BMDMA-specific restart code instead of statically
executing BMDMA-specific code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch begins refactoring the restart dma functions
out of bmdma to be shared with AHCI and other future
IDE HBA implementations.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-2-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
geometry: hd_geometry_guess function autodetects the drive geometry.
This patch adds a block backend call, that probes the backing device
geometry. If the inner driver method is implemented and succeeds
(currently only for DASDs), the blkconf_geometry will pass-through
the backing device geometry. Otherwise will fallback to old logic.
blocksize: This patch initializes blocksize properties to 0.
In order to set the property a blkconf_blocksizes was introduced.
If user didn't set physical or logical blocksize, it will
retrieve its value from a driver (only succeeds for DASD), otherwise
it will set default 512 value.
The blkconf_blocksizes call was added to all users of BlkConf.
Signed-off-by: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1424087278-49393-6-git-send-email-tumanova@linux.vnet.ibm.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A bunch of fixes all over the place.
All of ACPI refactoring has been merged.
Legacy pci commands have been dropped.
virtio header cleanup
initial patches from virtio-1.0 branch
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/CoXAAoJECgfDbjSjVRpX7EH/RMmgtsDO4wvqJu++lHvkB/q
kSaXZYTpJTo0i5JE7n2brwuXA4902tTg9g5TMUpGPh9Pt2QRg7RTgGC1vqZyOBos
MPw+4BO2v66S6qgX7bOf222z7r64cHTY7pLkQlrfD4usPlu2eusZ64UTW6Ru51fW
WF9E9aunbl+HnuCGq6Iez3sCLscTBJpU/lEr6oSyHhuq3aa0CjjraEeV0E/QcwJG
HTUeFymL8NFvlXZblsLI++VOv7Mxpi6yiCQ5XoKpFgGMvidwo41Aso6gB3ySGxOd
w8O3Nbu77Iw/StDRNCg/5/GapabMKh2bE4UCsYY5OS63ZtD0fl0CCblhzm/ZFPw=
=LY/j
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio fixes and cleanups
A bunch of fixes all over the place.
All of ACPI refactoring has been merged.
Legacy pci commands have been dropped.
virtio header cleanup
initial patches from virtio-1.0 branch
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* remotes/mst/tags/for_upstream: (130 commits)
acpi: drop unused code
aml-build: comment fix
acpi-build: fix typo in comment
acpi: update generated files
vhost user:support vhost user nic for non msi guests
aml-build: fix build for glib < 2.22
acpi: update generated files
Makefile.target: binary depends on config-devices
acpi-test-data: update after pci rewrite
acpi, mem-hotplug: use PC_DIMM_SLOT_PROP in acpi_memory_plug_cb().
pci-hotplug-old: Has been dead for five major releases, bury
pci: Give a few helpers internal linkage
acpi: make build_*() routines static to aml-build.c
pc: acpi: remove not used anymore ssdt-[misc|pcihp].hex.generated blobs
pc: acpi-build: drop template patching and create PCI bus tree dynamically
tests: ACPI: update pc/SSDT.bridge due to new alg of PCI tree creation
pc: acpi-build: simplify PCI bus tree generation
tests: add ACPI blobs for qemu with bridge cases
tests: bios-tables-test: add support for testing bridges
tests: ACPI test blobs update due to PCI0._CRS changes
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Conflicts:
hw/pci/pci-hotplug-old.c
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Convert the device models where initialization obviously can't fail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
isa_ide_init()'s callers don't check for failure. isa_ide_init()
looks like it could fail, but since isa_ide_realizefn() can't fail, it
actually can't. Replace its qdev_init() by qdev_init_nofail() to make
it obvious.
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
(With the previous atapi_dma flag recovery)
If migration happens between the ATAPI command being written and the
bmdma being started, the DMA is dropped. Eventually the guest times
out and recovers, but that can take many seconds.
(This is rare, on a pingpong reading the CD continuously I hit
this about ~1/30-1/50 migrates)
I don't think we've got enough state to be able to recover safely
at this point, so I throw a 'medium error, no seek complete'
that I'm assuming guests will try and recover from an apparently
dirty CD.
OK, it's a hack, the real solution is probably to push a lot of
ATAPI state into the migration stream, but this is a fix that
works with no stream changes. Tested only on Linux (both RHEL5
(pre-libata) and RHEL7).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If a migration happens just after the guest has kicked
off an ATAPI command and kicked off DMA, we lose the atapi_dma
flag, and the destination tries to complete the command as PIO
rather than DMA. This upsets Linux; modern libata based kernels
stumble and recover OK, older kernels end up passing bad data
to userspace.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
SCSI devices have multiple kinds of queries they need to respond
to, as defined in the "cmd inquiry" section in MMC-6 and SPC-3.
Relevent sections:
MMC-6 revision 2g:
Non-VPD response data and pointer to SPC-3;
Section 6.8 "Inquiry Command"
SPC-3 revision 23:
Inquiry command and error handling:
Section 6.4 "INQUIRY command"
VPD data pages format:
Section 7.6 "Vital product data parameters"
We implement these Vital Product Data queries for SCSI, but not for
ATAPI through IDE. The result is that if you are looking for the WWN
identifier via tools such as sg3_utils, you will be unable to query
our CD/DVD rom device to obtain it.
This patch adds the minimum number of mandatory responses as defined
by SPC-3, which include the "supported pages" response (page 0x00)
and the "Device Identification" response (page 0x83). It also correctly
responds when it receives a request for an illegal page to improve
error output from related tools.
The Device ID page contains an arbitrary list of identification
strings of various formats; the ID strings included in this patch
were chosen to mimic those provided by the libata driver when
emulating this SCSI query (model, serial, and wwn when present.)
Example:
# libata emulated response
[root@localhost ~]# sg_inq --id /dev/sda
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 24
designator_type: vendor specific [0x0], code_set: ASCII
associated with the addressed logical unit
vendor specific: QM00001
Designation descriptor number 2, descriptor length: 72
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: ATA
vendor specific: QEMU HARDDISK QM00001
# QEMU generated ATAPI response, with WWN
[root@localhost ~]# sg_inq --id /dev/sr0
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 24
designator_type: vendor specific [0x0], code_set: ASCII
associated with the addressed logical unit
vendor specific: QM00005
Designation descriptor number 2, descriptor length: 72
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: ATA
vendor specific: QEMU DVD-ROM QM00005
Designation descriptor number 3, descriptor length: 12
designator_type: NAA, code_set: Binary
associated with the addressed logical unit
NAA 5, IEEE Company_id: 0xc50
Vendor Specific Identifier: 0x15ea71bb
[0x5000c50015ea71bb]
See also: hw/scsi/scsi-disk.c, scsi_disk_emulate_inquiry()
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Our IDE emulation can't handle logical block sizes other than 512. Check
for it.
The original assumption was that other values would silently be ignored
(which is bad enough), but it's not quite true: The physical block size
is exposed in IDENTIFY DEVICE as a multiple of the logical block size.
Setting a logical block size therefore also corrupts the physical block
size (4096/4096 doesn't silently downgrade to 4096/512, but 512/512).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
SATA 3.0 "10.3.1 FIS Type values" defines the constants used to
differentiate between FIS types.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1415874281-7371-3-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Debug code using #ifdef is susceptible to bitrot because the compiler
never checks the debug code.
This is easy to avoid, change the DPRINTF() macro to use if (DEBUG_AHCI)
and always give it a 0 or 1 value.
This also allows us to drop an #ifdef DEBUG_AHCI in ahci_start_dma()
since the compiler can now see the local variable is used.
The motivation for this change is a recent DEBUG_AHCI build failure due
to an outdated DPRINTF() format string. From now on the compiler will
catch these errors.
Cc: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1415874281-7371-2-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The other callers to blk_set_enable_write_cache() in this file
already check for s->blk == NULL.
Signed-off-by: Don Slutz <dslutz@verizon.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1416259239-13281-1-git-send-email-dslutz@verizon.com
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to make handle_cmd more readable at the macro level,
the details of how to decompose particular types of FIS packets
are left to helper functions.
In our case, the only type of FIS packet we currently expect to
see is a Register H2D FIS packet, but the gory details of its
decomposition are of no particular interest in handle_cmd.
This patch keeps the receipt of FIS packets and the decomposition
thereof separated to two different functions.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1415058979-16604-6-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Instead of checking for a known byte, inspect the
fields of this byte explicitly to produce more meaningful
error messages and improve the readability of this section.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1415058979-16604-5-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Error checking in ahci's handle_cmd is re-ordered so that we
initialize as few things as possible before we've done our
sanity checking. This simplifies returning from this call
in case of an error.
A check to make sure the DMA memory map succeeds with the
correct size is also added, and the debug print of the
command fis is cleaned up with its size corrected.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1415058979-16604-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch introduces a few changes to how FIS packets are
deciphered in the AHCI virtual device. The summary of
changes can be grouped into two pieces:
[A] Changes to how we apply a preliminary sieve to FISes,
[B] Changes in how we internalize a decomposed FIS.
== Changes to how we apply a preliminary sieve to FISes ==
(1) Packets may now either update the Control register or
the Command register, but not both. This is according
to the SATA 3.2 specification which states:
"...the device either initiates processing of the command
indicated in the Command register or initiates processing
of the control request indicated [...] depending on the
state of the C bit in the FIS."
See SATA 3.2 section 10.5.5.4, "Reception" in the 10.5.5
"Register Host to Device FIS" section.
This change accounts for the first two regions of change
within the diff. All other changes belong to the following
changes.
== Changes in how we internalize a decomposed FIS ==
(2) Instead of trying to extract the sector number out of the
FIS from bytes 4-10 and setting it with ide_set_sector,
we set the appropriate IDEState registers and trust that
ide_get_sector can retrieve the correct sector later.
By "constructing" the sector for use with ide_set_sector,
we are duplicating the mechanisms of ide_get_sector.
This change makes the FIS decomposition more obvious.
SATA 3.2 as a specification does not make the legacy
register mapping with respect to the D2H FIS obvious.
However, SATA 3.2 section 10.5.5.1 "Register Host to
Device FIS layout" describes all of the "cmd_fis"
bytes:
0 - FIS Type (0x27)
1 - Port Multiplier Port and Command Update flag
2 - ATA Command
3 - Features_Low
4 - LBA 7:0
5 - LBA 15:8
6 - LBA 23:16
7 - Device, AKA "Drive Select."
8 - LBA 31:24
9 - LBA 39:32
10 - LBA 47:40
11 - Features_High
12 - Count Low
13 - Count High
14 - ICC
15 - Control
16-19 - Auxiliary (for NCQ, defined per-command)
Most of these registers map to existing IDEState registers
in obvious ways, especially features, select, hob_features,
and nsector (count). ICC is reserved in older specifications
but is not supported in our implementation, and remains
unused here. The Control register is not valid for a command
that is trying to update the command register and is to be
considered reserved at this point.
What is not obvious is the LBA register mappings, but SATA 1.0
can help inform of us legacy device support, see SATA 1.0 section
8.5.2 "Register - Host to Device."
LBA 7:0 - Sector Number (sector)
LBA 15:8 - Cyl Low (lcyl)
LBA 23:16 - Cyl High (hcyl)
LBA 31:24 - Sector Num Exp. (hob_sector)
LBA 39:32 - Cyl Low Exp. (hob_lcyl)
LBA 47:40 - Cyl High Exp. (hob_hcyl)
These mappings help guide which registers the FIS should be decomposed
into/towards for CHS, LBA28 and LBA48 commands.
As a note: The prior confusion that can be seen in the documentation
arises from the fact that CHS and LBA28 commands use the low nybble
of the drive select register to store LBA 27:24, whereas LNA48 commands
use the hob_sector, hob_lcyl and hob_hcyl registers as explained above.
The decomposition as it stands now will correctly decompose CHS, LBA28
and LBA48 commands into their appropriate registers where the core
IDE/ATAPI layers can deal with them correctly.
See the below point for more information.
(3) We save cmd_fis[7] as ide_state->select, which informs
decisions about if we are using LBA or CHS.
This corrects a bug in AHCI wherein we attempt to set and/or
retrieve the sector number by using ide_set_sector and
ide_get_sector, which depend on the select register to
determine if we are using LBA or CHS.
Without this adjustment, LBA48 read/writes are currently
broken. Thanks to Eniac Zheng @ HP for pointing this out.
(4) Save cmd_fis[11] as ide_state->hob_feature, as defined in SATA 3.2.
(5) For several ATA commands, the sector count register set to 0
is a magic number that means 256 sectors. For LBA48 commands,
this means 65,536 sectors. We drop the magic sector correction
here, and trust the ide core layer to handle the conversion
appropriately, in ide_cmd_lba48_transform(). As it stands,
the current AHCI code is only compliant with LBA28 commands.
By simply removing the magic, it will work with LBA28 and LBA48.
(6) We expand FIS decomposition to include both ATAPI and IDE devices.
We leave the logic of determining if the fields are valid or not
to the respective layers.
This change intends to make it clearer that AHCI is only a
composition mechanism for the FIS packets: the meanings of
the registers is best left to the implementation layers for
those devices.
(7) Forcefully setting the feature, hcyl and lcyl registers for ATAPI
commands is removed.
- The hcyl and lcyl magic present here is valid at boot only,
and should not be overridden for every PACKET command.
- The feature register is defined as valid for the PACKET command,
so we should not suppress it. The ATAPI layer does not even
currently depend on or require 0x01 as mandatory.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1415058979-16604-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
A small helper to determine which S/ATA commands
are destined to be routed to the NCQ pathways.
This references SATA 3.2 section 13.6,
Native Command Queueing. See sections 13.6.4,
13.6.5, 13.6.6, 13.6.7 and 13.6.8 for all
SATA commands considered to be part of the
NCQ feature set. This is summarized in a small
list in section 13.6.3.1 and again in 13.6.3.2.
Not all of these NCQ commands are currently supported,
so the error pathways are adjusted slightly to be more
informative in the case they are encountered.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1415058979-16604-2-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This impacts both BMDMA and AHCI HBA interfaces for IDE.
Currently, we confuse the difference between a PRDT having
"0 bytes" and a PRDT having "0 complete sectors."
When we receive an incomplete sector, inconsistent error checking
leads to an infinite loop wherein the call succeeds, but it
didn't give us enough bytes -- leading us to re-call the
DMA chain over and over again. This leads to, in the BMDMA case,
leaked memory for short PRDTs, and infinite loops and resource
usage in the AHCI case.
The .prepare_buf() callback is reworked to return the number of
bytes that it successfully prepared. 0 is a valid, non-error
answer that means the table was empty and described no bytes.
-1 indicates an error.
Our current implementation uses the io_buffer in IDEState to
ultimately describe the size of a prepared scatter-gather list.
Even though the AHCI PRDT/SGList can be as large as 256GiB, the
AHCI command header limits transactions to just 4GiB. ATA8-ACS3,
however, defines the largest transaction to be an LBA48 command
that transfers 65,536 sectors. With a 512 byte sector size, this
is just 32MiB.
Since our current state structures use the int type to describe
the size of the buffer, and this state is migrated as int32, we
are limited to describing 2GiB buffer sizes unless we change the
migration protocol.
For this reason, this patch begins to unify the assertions in the
IDE pathways that the scatter-gather list provided by either the
AHCI PRDT or the PCI BMDMA PRDs can only describe, at a maximum,
2GiB. This should be resilient enough unless we need a sector
size that exceeds 32KiB.
Further, the likelihood of any guest operating system actually
attempting to transfer this much data in a single operation is
very slim.
To this end, the IDEState variables have been updated to more
explicitly clarify our maximum supported size. Callers to the
prepare_buf callback have been reworked to understand the new
return code, and all versions of the prepare_buf callback have
been adjusted accordingly.
Lastly, the ahci_populate_sglist helper, relied upon by the
AHCI implementation of .prepare_buf() as well as the PCI
implementation of the callback have had overflow assertions
added to help make clear the reasonings behind the various
type changes.
[Added %d -> %"PRId64" fix John sent because off_pos changed from int to
int64_t.
--Stefan]
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1414785819-26209-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The intent of this patch is to further unify the creation and
deletion of the sglist used for all AHCI transfers, including
emulated PIO, ATAPI R/W, and native DMA R/W.
By replacing ahci_start_transfer's call to ahci_populate_sglist
with ahci_dma_prepare_buf, we reduce the number of direct calls
where we manipulate the scatter-gather list in the AHCI code.
To make this switch, the constant "0" passed as an offset
in ahci_dma_prepare_buf is adjusted to use io_buffer_offset.
For DMA pathways, this has no effect: io_buffer_offset is always
updated to 0 at the beginning of a DMA transfer loop regardless.
DMA pathways through ide_dma_cb() update the io_buffer_offset
accordingly, and for circumstances where we might make several
trips through this loop, this may actually correct a design flaw.
For PIO pathways, the newly updated ahci_dma_prepare_buf will
now prepare the sglist at the correct offset. It will also set
io_buffer_size, but this is not used in the cmd_read_pio or
cmd_write_pio pathways.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1414785819-26209-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, for emulated PIO transfers through the AHCI device,
any attempt made to request more than a single sector's worth
of data will result in the same sector being transferred over
and over.
For example, if we request 8 sectors via PIO READ SECTORS, the
AHCI device will give us the same sector eight times.
This patch adds offset tracking into the PIO pathways so that
we can fulfill these requests appropriately.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1414785819-26209-2-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch fixes a regression caused by commit
659142ecf7.
The problem occurs when we wish to return early
from the ahci_start_transfer function, but are now
updating the transferred byte count in the AHCI
command header via ahci_commit_buf.
This will cause problems in the Windows 8 installer.
Don't update the byte count in the command header
for the transmission of ATAPI packets: These commands
will distort the final byte count of the actual data
payload.
The call to ahci_commit_buf remains in the "out"
portion of the call in order to clean up the sglist.
The byte count is maintained by forcing size to be 0.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The SDB FIS creation was mangled;
We were writing the error byte to byte 0,
and omitting the SDB FIS magic byte.
Though the SDB packet layout states that:
byte 0: Must be 0xA1 to indicate SDB FIS.
byte 1: Port multiplier select & other flags
byte 2: status byte.
byte 3: error byte.
This patch adds an SDB FIS structure with
human-readable names, and ensures that we
are filling the structure appropriately.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1412204151-18117-7-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, DMA read/write operations neglect to update
the byte count after a successful transfer like ATAPI
DMA read or PIO read/write operations do.
We correct this oversight by adding another callback into
the IDEDMAOps structure. The commit callback is called
whenever we are cleaning up a scatter-gather list.
AHCI can register this callback in order to update post-
transfer information such as byte count updates.
We use this callback in AHCI to consolidate where we delete
the SGlist as generated from the PRDT, as well as update the
byte count after the transfer is complete.
The QEMUSGList structure has an init flag added to it in order
to make qemu_sglist_destroy a nop if it is called when
there is no sglist, which simplifies cleanup and error paths.
This patch fixes several AHCI problems, notably Non-NCQ modes
of operation for Windows 7 as well as Hibernate support for Windows 7.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1412204151-18117-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, the D2H FIS packets AHCI generates simply parrot back
the LBA that the guest sent to us in the cmd_fis. However, some
commands (like READ NATIVE MAX) modify the LBA registers as a
return value, through which the AHCI D2H FIS is the only response
mechanism. Thus, the D2H response should use the current register
values, not the initial ones.
This patch adjusts the LBA and drive select register responses for
PIO Setup and D2H FIS response packets.
Additionally, the PIO and D2H FIS responses copy too many bytes
from the command FIS that it is being generated from. Specifically,
byte 11 which is the Features(15:8) field for Register Host to
Device FIS packets, is instead reserved for the PIO Setup FIS and
should always be 0.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1412204151-18117-2-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Fix off-by-one error when unplugging disks, which would otherwise leave the last ATA disk plugged, with obvious consequences. Also rewrite loop to be more readable.
Signed-off-by: James Harper <james.harper@ejbdigital.com.au>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
This command lists PCMCIA sockets and cards. Only a few ARM boards
have sockets (akita, borzoi, connex, mainstone, spitz, terrier, tosa,
verdex, z2), the only card is the DSCM-1xxxx Hitachi Microdrive (qdev
"microdrive"), and it is only inserted during machine init, if ever.
So this command doesn't really tell anybody anything new so far.
Moreover, pcmcia_socket_unregister() has a use-after-free bug, flagged
by Coverity. Has never been used, because there has never been code
to eject a PCMCIA card.
Not worth fixing & converting to QMP. Remove it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Acked-by: Andreas Färber <afaerber@suse.de>
Message-id: 1411144812-22958-1-git-send-email-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
blockdev_init() always creates a DriveInfo, but only drive_new() fills
it in. qmp_blockdev_add() leaves it blank. This results in a drive
with type = IF_IDE, bus = 0, unit = 0. Screwed up in commit ee13ed1c.
Board initialization code looking for IDE drive (0,0) can pick up one
of these bogus drives. The QMP command has to execute really early to
be visible. Not sure how likely that is in practice.
Fix by creating DriveInfo in drive_new(). Block backends created by
blockdev-add don't get one.
Breaks the test for "has been created by qmp_blockdev_add()" in
blockdev_mark_auto_del() and do_drive_del(), because it changes the
value of dinfo && !dinfo->enable_auto_del from true to false. Simply
test !dinfo instead.
Leaves DriveInfo member enable_auto_del unused. Drop it.
A few places assume a block backend always has a DriveInfo. Fix them
up.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a BlockBackend member to TrimAIOCB, so ide_issue_trim_cb() can use
blk_aio_discard() instead of bdrv_aio_discard().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I'll use it with block backends shortly, and the name is going to fit
badly there. It's a block layer thing anyway, not just a block driver
thing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I'll use BlockDriverAIOCB with block backends shortly, and the name is
going to fit badly there. It's a block layer thing anyway, not just a
block driver thing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>