Since a59a293126 ("tcg/sparc64: Remove sparc32plus constraints")
we no longer distinguish registers with 32 vs 64 bits.
Therefore we can remove support for the backend-specific
type change opcodes.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Introduce a new opcode for negative setcond.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace the separate defines with TCG_TARGET_HAS_extr_i64_i32,
so that the two parts of backend-specific type changing cannot
be out of sync.
Reported-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: <20230822175127.1173698-1-richard.henderson@linaro.org>
Often, the only thing we need to know about the TCG host
is the register size.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Disconnect the layout of ArchCPU from TCG compilation.
Pass the relative offset of 'env' and 'neg.tlb.f' as a parameter.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This makes CPUTLBEntry agnostic to the address size of the guest.
When 32-bit addresses are in effect, we can simply read the low
32 bits of the 64-bit field. Similarly when we need to update
the field for setting TLB_NOTDIRTY.
For TCG backends that could in theory be big-endian, but in
practice are not (arm, loongarch, riscv), use QEMU_BUILD_BUG_ON
to document and ensure this is not accidentally missed.
For s390x, which is always big-endian, use HOST_BIG_ENDIAN anyway,
to document the reason for the adjustment.
For sparc64 and ppc64, always perform a 64-bit load, and rely on
the following 32-bit comparison to ignore the high bits.
Rearrange mips and ppc if ladders for clarity.
Reviewed-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
All uses replaced with TCGContext.addr_type.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The last use was removed by e77c89fb08.
Fixes: e77c89fb08 ("cputlb: Remove static tlb sizing")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Disconnect guest page size from TCG compilation.
While this could be done via exec/target_page.h, we want to cache
the value across multiple memory access operations, so we might
as well initialize this early.
The changes within tcg/ are entirely mechanical:
sed -i s/TARGET_PAGE_BITS/s->page_bits/g
sed -i s/TARGET_PAGE_MASK/s->page_mask/g
Reviewed-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For 32-bit hosts, we cannot simply rely on TCGContext.addr_bits,
as we need one or two host registers to represent the guest address.
Create the new opcodes and update all users. Since we have not
yet eliminated TARGET_LONG_BITS, only one of the two opcodes will
ever be used, so we can get away with treating them the same in
the backends.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add opcodes for backend support for 128-bit memory operations.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace the unparameterized TCG_TARGET_HAS_MEMORY_BSWAP macro
with a function with a memop argument.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Drop the target-specific trampolines for the standard slow path.
This lets us use tcg_out_helper_{ld,st}_args, and handles the new
atomicity bits within MemOp.
At the same time, use the full load/store helpers for user-only mode.
Drop inline unaligned access support for user-only mode, as it does
not handle atomicity.
Use TCG_REG_T[1-3] in the tlb lookup, instead of TCG_REG_O[0-2].
This allows the constraints to be simplified.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Emphasize that the constant is unsigned.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Shuffle the order in tcg_out_movi_int to check s13 first, and
drop this check from tcg_out_movi_imm32. This might make the
sequence for in_prologue larger, but not worth worrying about.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Emphasize that the constant is signed.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
With the current structure of cputlb.c, there is no difference
between the little-endian and big-endian entry points, aside
from the assert. Unify the pairs of functions.
Hoist the qemu_{ld,st}_helpers arrays to tcg.c.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We need to set this in TCGLabelQemuLdst, so plumb this
all the way through from tcg_out_op.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In tcg_canonicalize_memop, we remove MO_SIGN from MO_32 operations
with TCG_TYPE_I32. Thus this is never set. We already have an
identical test just above which does not include is_64
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We will want a backend interface for register swapping.
This is only properly defined for x86; all others get a
stub version that always indicates failure.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This is common code in most qemu_{ld,st} slow paths, extending the
input value for the store helper data argument or extending the
return value from the load helper.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We will need a backend interface for type truncation. For those backends
that did not enable TCG_TARGET_HAS_extrl_i64_i32, use tcg_out_mov.
Use it in tcg_reg_alloc_op in the meantime.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We will need a backend interface for type extension with zero.
Use it in tcg_reg_alloc_op in the meantime.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We will need a backend interface for type extension with sign.
Use it in tcg_reg_alloc_op in the meantime.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We will need a backend interface for performing 32-bit zero-extend.
Use it in tcg_reg_alloc_op in the meantime.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We will need a backend interface for performing 32-bit sign-extend.
Use it in tcg_reg_alloc_op in the meantime.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We will need a backend interface for performing 16-bit zero-extend.
Use it in tcg_reg_alloc_op in the meantime.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We will need a backend interface for performing 16-bit sign-extend.
Use it in tcg_reg_alloc_op in the meantime.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We will need a backend interface for performing 8-bit zero-extend.
Use it in tcg_reg_alloc_op in the meantime.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We will need a backend interface for performing 8-bit sign-extend.
Use it in tcg_reg_alloc_op in the meantime.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Something is wrong with this code, and also wrong with gdb on the
sparc systems to which I have access, so I cannot debug it either.
Disable for now, so the release is not broken.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Fill in the parameters for the host ABI for Int128 for
those backends which require no extra modification.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace the flat array tcg_target_call_oarg_regs[] with
a function call including the TCGCallReturnKind.
Extend the set of registers for ARM to r0-r3 to match the ABI:
https://github.com/ARM-software/abi-aa/blob/main/aapcs32/aapcs32.rst#result-return
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Implement the function for arm, i386, and s390x, which will use it.
Add stubs for all other backends.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The old sparc64 implementation may replace two insns, which leaves
a race condition in which a thread could be stopped at a PC in the
middle of the sequence, and when restarted does not see the complete
address computation and branches to nowhere.
The new implemetation replaces only one insn, swapping between a
direct branch and a direct call. The TCG_REG_TB register is loaded
from tb->jmp_target_addr[] in the delay slot.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This is always true for sparc64, so this is dead since 3a5f6805c7.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We now have the option to generate direct or indirect
goto_tb depending on the dynamic displacement, thus
the define is no longer necessary or completely accurate.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace 'tc_ptr' and 'addr' with 'tb' and 'n'.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The INDEX_op_goto_tb opcode needs no register allocation.
Split out a dedicated helper function for it.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Similar to the existing set_jmp_reset_offset. Move any assert for
TCG_TARGET_HAS_direct_jump into the new function (which now cannot
be build-time). Will be unused if TCG_TARGET_HAS_direct_jump is
constant 0, but we can't test for constant in the preprocessor,
so just mark it G_GNUC_UNUSED.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The INDEX_op_exit_tb opcode needs no register allocation.
Split out a dedicated helper function for it.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This eliminates an ifdef for TCI, and will be required for
expanding the call for TCGv_i128.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For 64-bit hosts that had TCG_TARGET_EXTEND_ARGS, set
TCG_TARGET_CALL_ARG_I32 to TCG_CALL_ARG_EXTEND.
Otherwise, use TCG_CALL_ARG_NORMAL.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
