No tests were covering write zeroes with unmap. Additionally,
I needed to prove that my previous patches for correct status
reporting and write zeroes optimizations actually had an impact.
The test works for cluster_size between 8k and 2M (for smaller
sizes, it fails because our allocation patterns are not contiguous
with small clusters - in part, the largest consecutive allocation
we tend to get is often bounded by the size covered by one L2
table).
Note that testing for zero clusters is tricky: 'qemu-io map'
reports whether data comes from the current layer of the image
(useful for sniffing out which regions of the file have
QCOW_OFLAG_ZERO) - but doesn't show which clusters have mappings;
while 'qemu-img map' sees "zero":true for both unallocated and
zero clusters for any qcow2 with no backing layer (so less useful
at detecting true zero clusters), but reliably shows mappings.
So we have to rely on both queries side-by-side at each point of
the test.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170507000552.20847-10-eblake@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Although _filter_qemu_img_map documents that it scrubs offsets, it
was only doing so for human mode. Of the existing tests using the
filter (97, 122, 150, 154, 176), two of them are affected, but it
does not hurt the validity of the tests to not require particular
mappings (another test, 66, uses offsets but intentionally does not
pass through _filter_qemu_img_map, because it checks that offsets
are unchanged before and after an operation).
Another justification for this patch is that it will allow a future
patch to utilize 'qemu-img map --output=json' to check the status of
preallocated zero clusters without regards to the mapping (since
the qcow2 mapping can be very sensitive to the chosen cluster size,
when preallocation is not in use).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170507000552.20847-9-eblake@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Treat plain zero clusters differently from allocated ones, so that
we can simplify the logic of checking whether an offset is present.
Do this by splitting QCOW2_CLUSTER_ZERO into two new enums,
QCOW2_CLUSTER_ZERO_PLAIN and QCOW2_CLUSTER_ZERO_ALLOC.
I tried to arrange the enum so that we could use
'ret <= QCOW2_CLUSTER_ZERO_PLAIN' for all unallocated types, and
'ret >= QCOW2_CLUSTER_ZERO_ALLOC' for allocated types, although
I didn't actually end up taking advantage of the layout.
In many cases, this leads to simpler code, by properly combining
cases (sometimes, both zero types pair together, other times,
plain zero is more like unallocated while allocated zero is more
like normal).
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-id: 20170507000552.20847-7-eblake@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Use blkdebug's new geometry constraints to emulate setups that
have needed past regression fixes: write zeroes asserting
when running through a loopback block device with max-transfer
smaller than cluster size, and discard rounding away portions
of requests not aligned to preferred boundaries. Also, add
coverage that the block layer is honoring max transfer limits.
For now, a single iotest performs all actions, with the idea
that we can add future blkdebug constraint test cases in the
same file; but it can be split into multiple iotests if we find
reason to run one portion of the test in more setups than what
are possible in the other.
For reference, the final portion of the test (checking whether
discard passes as much as possible to the lowest layers of the
stack) works as follows:
qemu-io: discard 30M at 80000001, passed to blkdebug
blkdebug: discard 511 bytes at 80000001, -ENOTSUP (smaller than
blkdebug's 512 align)
blkdebug: discard 14371328 bytes at 80000512, passed to qcow2
qcow2: discard 739840 bytes at 80000512, -ENOTSUP (smaller than
qcow2's 1M align)
qcow2: discard 13M bytes at 77M, succeeds
blkdebug: discard 15M bytes at 90M, passed to qcow2
qcow2: discard 15M bytes at 90M, succeeds
blkdebug: discard 1356800 bytes at 105M, passed to qcow2
qcow2: discard 1M at 105M, succeeds
qcow2: discard 308224 bytes at 106M, -ENOTSUP (smaller than qcow2's
1M align)
blkdebug: discard 1 byte at 111457280, -ENOTSUP (smaller than
blkdebug's 512 align)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170429191419.30051-10-eblake@redhat.com
[mreitz: For cooperation with image locking, add -r to the qemu-io
invocation which verifies the image content]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Mixing byte offset and sector allocation counts is a bit
confusing. Also, reporting n/m sectors, where m decreases
according to the remaining size of the file, isn't really
adding any useful information; and reporting an offset at
both the front and end of the line, with large amounts of
whitespace, is pointless. Update the output to use byte
counts and shorter lines, then adjust the affected tests
(./check -qcow2 102, ./check -vpc 146).
Note that 'qemu-io map' is MUCH weaker than 'qemu-img map';
the former only shows which regions of the active layer are
allocated, without regards to where the allocation comes from
or whether the allocated portion is known to read as zero
(because it is using the weaker bdrv_is_allocated()); while the
latter (especially in --output=json mode) reports more details
from bdrv_get_block_status().
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-id: 20170429191419.30051-4-eblake@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
For the 'alloc' command, accepting an offset in bytes but a length
in sectors, and reporting output in sectors, is confusing. Do
everything in bytes, and adjust the expected output accordingly.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-id: 20170429191419.30051-3-eblake@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
066 was supposed to be a test "for discarding preallocated zero
clusters", but it did so incompletely: While it did check the image
file's integrity after the operation, it did not confirm that the
clusters are indeed freed. This patch adds this test.
In addition, new cases for writing to preallocated zero clusters are
added.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The COLO block replication architecture requires one disk to be shared
between primary and secondary, in the test both processes use posix file
protocol (instead of over NBD) so it is affected by image locking.
Disable the lock.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The test scenario doesn't require the same image, instead it focuses on
the duplicated node-name, so use null-co to avoid locking conflict.
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In the case where we test the expected error when a blockdev-snapshot
target already has a backing image, the backing chain is opened multiple
times. This will be a problem when we use image locking, so use a
different backing file that is not already open.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Double attach is not a valid usage of the target image, drive-backup
will open the blockdev itself so skip the add_drive call in this case.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The qemu-img info command is executed while VM is running, add -U option
to avoid the image locking error.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qemu-img and qemu-io commands when guest is running need "-U" option,
add it.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
At the request of Michael, replace the leading capital X in the FADT
field name Xfacs and Xdsdt with lower case x + underscore.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----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=R5f2
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'danpb/tags/pull-qcrypto-2017-05-09-1' into staging
Merge qcrypto 2017/05/09 v1
# gpg: Signature made Tue 09 May 2017 09:43:47 AM EDT
# gpg: using RSA key 0xBE86EBB415104FDF
# gpg: Good signature from "Daniel P. Berrange <dan@berrange.com>"
# gpg: aka "Daniel P. Berrange <berrange@redhat.com>"
# Primary key fingerprint: DAF3 A6FD B26B 6291 2D0E 8E3F BE86 EBB4 1510 4FDF
* danpb/tags/pull-qcrypto-2017-05-09-1:
crypto: qcrypto_random_bytes() now works on windows w/o any other crypto libs
crypto: move 'opaque' parameter to (nearly) the end of parameter list
List SASL config file under the cryptography maintainer's realm
Default to GSSAPI (Kerberos) instead of DIGEST-MD5 for SASL
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 78f86a2b7 added a new test, but forgot to exclude the built
binary from version control.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Previous commit moved 'opaque' to be the 2nd parameter in the list:
commit 375092332e
Author: Fam Zheng <famz@redhat.com>
Date: Fri Apr 21 20:27:02 2017 +0800
crypto: Make errp the last parameter of functions
Move opaque to 2nd instead of the 2nd to last, so that compilers help
check with the conversion.
this puts it back to the 2nd to last position.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
SocketAddressLegacy is a simple union, and simple unions are awkward:
they have their variant members wrapped in a "data" object on the
wire, and require additional indirections in C. SocketAddress is the
equivalent flat union. Convert all users of SocketAddressLegacy to
SocketAddress, except for existing external interfaces.
See also commit fce5d53..9445673 and 85a82e8..c5f1ae3.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1493192202-3184-7-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[Minor editing accident fixed, commit message and a comment tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The next commit will rename SocketAddressFlat to SocketAddress, and
the commit after that will replace most uses of SocketAddressLegacy by
SocketAddress, replacing most of this commit's renames right back.
Note that checkpatch emits a few "line over 80 characters" warnings.
The long lines are all temporary; the SocketAddressLegacy replacement
will shorten them again.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1493192202-3184-5-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Commit 62c39b3 introduced test-qga, and at face value, appears
to be testing the 'guest-sync' behavior that is recommended for
guests in sending 0xff to QGA to force the parser to reset. But
this aspect of the test has never actually done anything: the
qmp_fd() call chain converts its string argument into QObject,
then converts that QObject back to the actual string that is
sent over the wire - and the conversion process silently drops
the 0xff byte from the string sent to QGA, thus never resetting
the QGA parser.
An upcoming patch will get rid of the wasteful round trip
through QObject, at which point the string in test-qga will be
directly sent over the wire.
But fixing qmp_fd() to actually send 0xff over the wire is not
all we have to do - the actual QMP parser loudly complains that
0xff is not valid JSON, and sends an error message _prior_ to
actually parsing the 'guest-sync' or 'guest-sync-delimited'
command. With 'guest-sync', we cannot easily tell if this error
message is a result of our command - which is WHY we invented
the 'guest-sync-delimited' command. So for the testsuite, fix
things to only check 0xff behavior on 'guest-sync-delimited',
and to loop until we've consumed all garbage prior to the
requested delimiter, which is compatible with the documented actions
that a real QGA client is supposed to do.
Ideally, we'd fix the QGA JSON parser to silently ignore 0xff
rather than sending an error message back, at which point we
could enhance this test for 'guest-sync' as well as for
'guest-sync-delimited'. But for the sake of this patch, our
testing of 'guest-sync' is no worse than it was pre-patch,
because we have never been sending 0xff over the wire in the
first place.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20170427215821.19397-11-eblake@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
[Additional comment squashed in, along with matching commit message
update]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Use the preferred blockdev-change-medium command instead.
Also, use of 'device' is deprecated; adding an explicit id on
the command line lets us use 'id' for both blockdev-change-medium
and eject.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20170427215821.19397-10-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
We now have macros in place to make it less verbose to add a scalar
to QDict and QList, so use them.
Patch created mechanically via:
spatch --sp-file scripts/coccinelle/qobject.cocci \
--macro-file scripts/cocci-macro-file.h --dir . --in-place
then touched up manually to fix a couple of '?:' back to original
spacing, as well as avoiding a long line in monitor.c.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20170427215821.19397-7-eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
We have macros in place to make it less verbose to add a subtype
of QObject to both QDict and QList. While we have made cleanups
like this in the past (see commit fcfcd8ffc, for example), having
it be automated by Coccinelle makes it easier to maintain.
Patch created mechanically via:
spatch --sp-file scripts/coccinelle/qobject.cocci \
--macro-file scripts/cocci-macro-file.h --dir . --in-place
then I verified that no manual touchups were required.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20170427215821.19397-5-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Gcc 7 (on Fedora 26) spotted odd use of integers instead of a
boolean; it's got a point.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170406154107.9178-1-dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
but it'll come in the next pull request.
* use GDB XML register description for x86
* use _Static_assert in QEMU_BUILD_BUG_ON
* add "R:" to MAINTAINERS and get_maintainers
* checkpatch improvements
* dump threading fixes
* first part of vhost-user-scsi support
* QemuMutex tracing
* vmw_pvscsi and megasas fixes
* sgabios module update
* use Rev3 (ACPI 2.0) FADT
* deprecate -hdachs
* improve -accel documentation
* hax fix
* qemu-char GSource bugfix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZDE+gAAoJEL/70l94x66DIpYH/1IOz3u8ObD8D4Lor07LkCCZ
vWFnTBMgGi9gTL5JQDnukRR3cmNp9EVOtAP5Yf+v+/Xqyq/FNGnoVWxCxEby7LtN
zrIXbsKMCaEcGzRNJFcbKV+KZnzkJrz92J0NHy29ruCK1AsslOXAWf4Qb1MV+fQl
6w2Upsh35usvWCNpFm2o8arzMEmNuE2xJDPKUB11GMrZT6TExq4Zqa8Zj1Ihc0sX
XcDr+eeBmb65Vv3jQLntOhSWAy0Xxf/fDXYTQx+JLHFgvpSOIWMiS+fqIVXtT0bH
0E4hQrBr0qjes8n8+9WGGQW2k8Ak0QlDvrZnQ97hTeV1k6SxW+2ATO2mLeJp9TM=
=5hf2
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'bonzini/tags/for-upstream' into staging
A large set of small patches. I have not included yet vhost-user-scsi,
but it'll come in the next pull request.
* use GDB XML register description for x86
* use _Static_assert in QEMU_BUILD_BUG_ON
* add "R:" to MAINTAINERS and get_maintainers
* checkpatch improvements
* dump threading fixes
* first part of vhost-user-scsi support
* QemuMutex tracing
* vmw_pvscsi and megasas fixes
* sgabios module update
* use Rev3 (ACPI 2.0) FADT
* deprecate -hdachs
* improve -accel documentation
* hax fix
* qemu-char GSource bugfix
# gpg: Signature made Fri 05 May 2017 06:10:40 AM EDT
# gpg: using RSA key 0xBFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* bonzini/tags/for-upstream: (21 commits)
vhost-scsi: create a vhost-scsi-common abstraction
libvhost-user: replace vasprintf() to fix build
get_maintainer: add subsystem to reviewer output
get_maintainer: --r (list reviewer) is on by default
get_maintainer: it's '--pattern-depth', not '-pattern-depth'
get_maintainer: Teach get_maintainer.pl about the new "R:" tag
MAINTAINERS: Add "R:" tag for self-appointed reviewers
Fix the -accel parameter and the documentation for 'hax'
dump: Acquire BQL around vm_start() in dump thread
hax: Fix memory mapping de-duplication logic
checkpatch: Disallow glib asserts in main code
trace: add qemu mutex lock and unlock trace events
vmw_pvscsi: check message ring page count at initialisation
sgabios: update for "fix wrong video attrs for int 10h,ah==13h"
scsi: avoid an off-by-one error in megasas_mmio_write
vl: deprecate the "-hdachs" option
use _Static_assert in QEMU_BUILD_BUG_ON
target/i386: Add GDB XML register description support
char: Fix removing wrong GSource that be found by fd_in_tag
hw/i386: Build-time assertion on pc/q35 reset register being identical.
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Ignore test executables when building in-tree:
test-arm-mptimer introduced in commit 882fac3
test-crypto-hmac introduced in commit 4fd460b
test-aio-multithread introduced in commit 0c330a7
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add a /chardevs container object to hold the list of chardevs.
(Note: QTAILQ chardevs is going away in the following commits)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
This updates the FADT generated for x86/64 machine types from Revision 1 to 3. (Based on ACPI standard 2.0 instead of 1.0) The intention is to expose the reset register information to guest operating systems which require it, specifically OS X/macOS. Revision 1 FADTs do not contain the fields relating to the reset register.
The new layout and contents remains backwards-compatible with operating systems which only support ACPI 1.0, as the existing fields are not modified by this change, as the 64-bit and 32-bit variants are allowed to co-exist according to the ACPI 2.0 standard. No regressions became apparent in tests with a range of Windows (XP-10) and Linux versions.
The BIOS tables test suite's FADT checksum test has also been updated to reflect the new FADT layout and content.
Signed-off-by: Phil Dennis-Jordan <phil@philjordan.eu>
Message-Id: <1489558827-28971-2-git-send-email-phil@philjordan.eu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If you are running out-of-tree, the -x option to exclude
a certain iotest is broken.
Replace porcelain usage of ls with a sturdier awk command.
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20170427205100.9505-3-jsnow@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Split the help text to highlight the groups of options
a little better, carving out a clear "format" and
"protocols" section.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20170427205100.9505-2-jsnow@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
As mentioned in commit 0c1bd46, we ignored requests to
discard the trailing cluster of an unaligned image. While
discard is an advisory operation from the guest standpoint,
(and we are therefore free to ignore any request), our
qcow2 implementation exploits the fact that a discarded
cluster reads back as 0. As long as we discard on cluster
boundaries, we are fine; but that means we could observe
non-zero data leaked at the tail of an unaligned image.
Enhance iotest 66 to cover this case, and fix the implementation
to honor a discard request on the final partial cluster.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-id: 20170407013709.18440-1-eblake@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
It does not make much sense to use a backing image for the target when
you concatenate multiple images (because then there is no correspondence
between the source images' backing files and the target's); but it was
still possible to give one by using -o backing_file=X instead of -B X.
Fix this by moving the check.
(Also, change the error message because -B is not the only way to
specify the backing file, evidently.)
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Mirror calculates job len from current I/O progress:
s->common.len = s->common.offset +
(cnt + s->sectors_in_flight) * BDRV_SECTOR_SIZE;
The final "len" of a failed mirror job in iotests 109 depends on the
subtle timing of the completion of read and write issued in the first
mirror iteration. The second iteration may or may not have run when the
I/O error happens, resulting in non-deterministic output of the
BLOCK_JOB_COMPLETED event text.
Similar to what was done in a752e4786, filter out the field to make the
test robust.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
s/refcout/refcount/
CC: qemu-trivial@nongnu.org
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There is no reason for the qemu-nbd server used for tests not to accept
an arbitrary number of clients. In fact, test 181 will require it to
accept two clients at the same time (and thus it fails before this
patch).
This patch updates common.rc to launch qemu-nbd with -e 42 which should
be enough for all of our current and future tests.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It is unused.
Suggested-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
We test for the presence of perl and bc and save their path in the
variables PERL_PROG and BC_PROG, but never actually make use of them.
Remove the checks and assignments so qemu-iotests can run even when
bc isn't installed.
Reported-by: Yash Mankad <ymankad@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The only thing the escape characters achieve is making the reference
output unreadable and lines that are potentially so long that git
doesn't want to put them into an email any more. Let's filter them out.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
HMP commands do not get any automatic testing yet, so on certain
QEMU machines, some HMP commands were causing crashes in the past.
Thus we should test HMP commands in our test suite, too, to avoid
that such problems creep in again in the future.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1493097407-20482-1-git-send-email-thuth@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Some tests need to run single tests for every available machine of the
current QEMU binary. To avoid code duplication, let's extract this
code that deals with 'query-machines' into a separate function.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1490860207-8302-3-git-send-email-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
When running certain HMP commands (like "device_del") via QMP, we
can sometimes get a QMP event in the response first, so that the
"g_assert(ret)" statement in qtest_hmp() triggers and the test
fails. Fix this by ignoring such QMP events while looking for the
real return value from QMP.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1490860207-8302-2-git-send-email-thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Added note to qtest_hmp/qtest_hmpv's header description to say
it discards events
For the tests that use the common.qemu functions for running a QEMU
process, _cleanup_qemu must be called in the exit function.
If it is not, if the qemu process aborts, then not all of the droppings
are cleaned up (e.g. pidfile, fifos).
This updates those tests that did not have a cleanup in qemu-iotests.
(I swapped spaces for tabs in test 102 as well)
Reported-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Message-id: d59c2f6ad6c1da8b9b3c7f357c94a7122ccfc55a.1492544096.git.jcody@redhat.com
The protocol VXHS does not support image creation. Some tests expect
to be able to create images through the protocol. Exclude VXHS from
these tests.
Signed-off-by: Jeff Cody <jcody@redhat.com>
Move opaque to 2nd instead of the 2nd to last, so that compilers help
check with the conversion.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170421122710.15373-7-famz@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[Commit message typo corrected]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Currently all trace.o are linked into qemu-system, qemu-img,
qemu-nbd, qemu-io etc., even the corresponding components
are not included.
Put all trace.o into libqemuutil.a that the linker would only pull in .o
files containing symbols that are actually referenced by the
program.
Signed-off -by: Anthony Xu <anthony.xu@intel.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Throttling has a weird property that throttle_get_config() does not
always return the same throttling settings that were given with
throttle_config(). In other words, the set and get functions aren't
symmetric.
If .max is 0 then the throttling code assigns a default value of .avg /
10 in throttle_config(). This is an implementation detail of the
throttling algorithm. When throttle_get_config() is called the .max
value returned should still be 0.
Users are exposed to this quirk via "info block" or "query-block"
monitor commands. This has caused confusion because it looks like a bug
when an unexpected value is reported.
This patch hides the .max value adjustment in throttle_get_config() and
updates test-throttle.c appropriately.
Reported-by: Nini Gu <ngu@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20170301115026.22621-4-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The (burst) max parameter cannot be smaller than the avg parameter.
There is a test case that uses avg = 56, max = 1 and gets away with it
because no input validation is performed by the test case.
This patch switches to valid test input parameters.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20170301115026.22621-3-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
BDRV_POLL_WHILE waits for the started I/O by releasing bs's ctx then polling
the main context, which relies on the yielded coroutine continuing on bs->ctx
before notifying qemu_aio_context with bdrv_wakeup().
Thus, using qemu_coroutine_enter to start I/O is wrong because if the coroutine
is entered from main loop, co->ctx will be qemu_aio_context, as a result of the
"release, poll, acquire" loop of BDRV_POLL_WHILE, race conditions happen when
both main thread and the iothread access the same BDS:
main loop iothread
-----------------------------------------------------------------------
blockdev_snapshot
aio_context_acquire(bs->ctx)
virtio_scsi_data_plane_handle_cmd
bdrv_drained_begin(bs->ctx)
bdrv_flush(bs)
bdrv_co_flush(bs) aio_context_acquire(bs->ctx).enter
...
qemu_coroutine_yield(co)
BDRV_POLL_WHILE()
aio_context_release(bs->ctx)
aio_context_acquire(bs->ctx).return
...
aio_co_wake(co)
aio_poll(qemu_aio_context) ...
co_schedule_bh_cb() ...
qemu_coroutine_enter(co) ...
/* (A) bdrv_co_flush(bs) /* (B) I/O on bs */
continues... */
aio_context_release(bs->ctx)
aio_context_acquire(bs->ctx)
Note that in above case, bdrv_drained_begin() doesn't do the "release,
poll, acquire" in BDRV_POLL_WHILE, because bs->in_flight == 0.
Fix this by using bdrv_coroutine_enter and enter coroutine in the right
context.
iotests 109 output is updated because the coroutine reenter flow during
mirror job complete is different (now through co_queue_wakeup, instead
of the unconditional qemu_coroutine_switch before), making the end job
len different.
Signed-off-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Previously, before test_block_job_start returns, the job can already
complete, as a result, the transactional state of other jobs added to
the same txn later cannot be handled correctly.
Move the block_job_start() calls to callers after
block_job_txn_add_job() calls.
Signed-off-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The channel socket was initialized manually, but forgot to set
QIO_CHANNEL_FEATURE_SHUTDOWN. Thus, the colo_process_incoming_thread
would hang at recvmsg. This patch just call qio_channel_socket_new to
get channel, Which set QIO_CHANNEL_FEATURE_SHUTDOWN already.
Signed-off-by: Wang Guang<wang.guang55@zte.com.cn>
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Occasionally if a test crashes or is interrupted by the user
at the wrong moment it could leave behind a stale UNIX
socket in /tmp/. This will then cause a subsequent test
run to fail spuriously with
tests/libqtest.c:70:init_socket: assertion failed (ret != -1): (-1 != -1)
if it happens to reuse the same PID.
Defend against this by deleting any stray stale socket before
trying to open the new ones for this test.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1490963801-27870-1-git-send-email-peter.maydell@linaro.org
Tweak 097 and 176 to operate on an image that is not cluster-aligned,
to give further coverage of clearing out an entire image, including
the recent fix to eliminate the difference between fast path (97) and
slow (176) for qcow2. Also tested on qcow (97 only, since qcow lacks
snapshots).
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-id: 20170331185356.2479-4-eblake@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The previous commit:
commit a3e1505dae
Author: Eric Blake <eblake@redhat.com>
Date: Mon Dec 5 09:49:34 2016 -0600
qcow2: Don't strand clusters near 2G intervals during commit
extended the 097 test case so that it did two passes, once
with an internal snapshot, once without.
qcow (v1) does not support internal snapshots, so this change
broke test 097 when run against qcow.
This splits 097 in two, creating a new 176 that tests the
internal snapshot codepath, effectively putting 097 back
to its content before the above commit.
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <20170221115512.21918-8-berrange@redhat.com>
[eblake: test collisions: s/173/176/g]
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-id: 20170331185356.2479-2-eblake@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
SocketAddress is a simple union, and simple unions are awkward: they
have their variant members wrapped in a "data" object on the wire, and
require additional indirections in C. I intend to limit its use to
existing external interfaces, and convert all internal interfaces to
SocketAddressFlat.
BlockdevOptionsNbd is an external interface using SocketAddress. We
already use SocketAddressFlat elsewhere in blockdev-add. Replace it
by SocketAddressFlat while we can (it's new in 2.9) for simplicity and
consistency. For example,
{ "execute": "blockdev-add",
"arguments": { "node-name": "foo", "driver": "nbd",
"server": { "type": "inet",
"data": { "host": "localhost",
"port": "12345" } } } }
becomes
{ "execute": "blockdev-add",
"arguments": { "node-name": "foo", "driver": "nbd",
"server": { "type": "inet",
"host": "localhost", "port": "12345" } } }
Since the internal interfaces still take SocketAddress, this requires
conversion function socket_address_crumple(). It'll go away when I
update the interfaces.
Unfortunately, SocketAddress is also visible in -drive since 2.8:
-drive if=none,driver=nbd,server.type=inet,server.data.host=127.0.0.1,server.data.port=12345
Nobody should be using it, as it's fairly new and has never been
documented, so adding still more compatibility gunk to keep it working
isn't worth the trouble. You now have to use
-drive if=none,driver=nbd,server.type=inet,server.host=127.0.0.1,server.port=12345
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1490895797-29094-9-git-send-email-armbru@redhat.com
[mreitz: Change iotest 147 accordingly]
Because of this interface change, iotest 147 has to be adapted.
Unfortunately, we cannot just flatten all of the addresses because
nbd-server-start still takes a plain SocketAddress. Therefore, we need
both and this is most easily achieved by writing the SocketAddress into
the code and flattening it where necessary.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170330221243.17333-1-mreitz@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
There's no reason to pack structures where we don't care about size or
padding, this applies to AcpiStdTable in tests/acpi-utils.h.
OTOH bios-tables-test happens to be passing the address of a field in
this struct to a function that expects a pointer to normally aligned
data which results in a SIGBUS on architectures like SPARC that have
strict alignment requirements.
Fixes: 9e8458c02 ("acpi unit-test: compare DSDT and SSDT tables against expected values")
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Peter Maydell <peter.maydell@linaro.org>
It's been a long journey, but here we are.
The supported blockdev-add is not compatible to its experimental
predecessors; bump all Since: tags to 2.9.
x-blockdev-remove-medium, x-blockdev-insert-medium and
x-blockdev-change need a bit more work, so leave them alone for now.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
For a packed struct like 'P9Hdr' the fields within it may not be
aligned as much as the natural alignment for their types. This means
it is not valid to pass the address of such a field to a function
like le32_to_cpus() which operate on uint32_t* and assume alignment.
Doing this results in a SIGBUS on hosts like SPARC which have strict
alignment requirements.
Use ldl_le_p() instead, which is specified to correctly handle
unaligned pointers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
a qemu with an empty s390 guest will exit very quickly. This races
against the testsuite reading from the console pipe leading to
intermittent test suite failures. Using -no-shutdown will keep
the guest running.
Fixes: 864111f422 (vl: exit qemu on guest panic if -no-shutdown is not set)
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-id: 1490361570-288658-1-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An off-by-one in commit 15c2f669e meant that we were failing to
check for unparsed input in all QemuOpts visitors. Recent testsuite
additions show that fixing the obvious bug with bogus fields will
also fix the case of an incomplete list visit; update the tests to
match the new behavior.
Simple testcase:
./x86_64-softmmu/qemu-system-x86_64 -nodefaults -nographic -qmp stdio -numa node,size=1g
failed to diagnose that 'size' is not a valid argument to -numa, and
now once again reports:
qemu-system-x86_64: -numa node,size=1g: Invalid parameter 'size'
See also https://bugzilla.redhat.com/show_bug.cgi?id=1434666
CC: qemu-stable@nongnu.org
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20170322144525.18964-4-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Commit 15c2f669e broke the ability of the QemuOpts visitor to
flag extra input parameters, but the regression went unnoticed
because of missing testsuite coverage. Add a test to cover this;
take the approach already used in 9cb8ef3 of adding a test that
passes (to avoid breaking bisection) but marks with BUG the
behavior that we don't like, so that the actual impact of the
fix in a later patch is easier to see.
CC: qemu-stable@nongnu.org
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Message-Id: <20170322144525.18964-2-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The new test demonstrates known bugs: integers between INT64_MAX+1 and
UINT64_MAX rejected, and integers between INT64_MIN and -1 are
accepted modulo 2^64.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1490118290-6133-1-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Visiting a list when input is the empty string should result in an
empty list, not an error. Noticed when commit 3d089ce belatedly added
tests, but simply accepted as weird then. It's actually a regression:
broken in commit 74f24cb, v2.7.0. Fix it, and throw in another test
case for empty string.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1490026424-11330-2-git-send-email-armbru@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
We have a number of negative tests, but we don't have systematic
positive coverage. Fix that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1490015515-25851-6-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
test-qapi.py used to print the internal representation of doc comments
(commit 3313b61). This went away when we dropped the doc comments in
positive tests (commit 87c16dc). Bring it back, because I'm going to
add real positive doc comment tests.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1490015515-25851-5-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1490014548-15083-4-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
We have a negative test case for a list index with leading zero. Add
positive ones.
Tweak the test case for list index greater or equal the number of
elements: test "equal" instead of "greater" to guard against
off-by-one mistakes.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1490014548-15083-2-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
When choking on a token where an expression is expected, we report
'Expected "{", "[" or string'. Close, but no cigar. Fix it to
Expected '"{", "[", string, boolean or "null"'.
Missed in commit e53188a.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1489582656-31133-48-git-send-email-armbru@redhat.com>
check_definition_doc() checks for member documentation without a
matching member. It laboriously second-guesses what members
QAPISchema._def_exprs() will create. That's a stupid game.
Move the check into QAPISchema.check(), where the members are known.
Delegate the actual checking to new QAPIDoc.check().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1489582656-31133-38-git-send-email-armbru@redhat.com>
New test doc-bad-union-member.json shows we can fail to reject
documentation for nonexistent members.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1489582656-31133-37-git-send-email-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1489582656-31133-36-git-send-email-armbru@redhat.com>
Results in a more precise error location, but the real reason is
emptying out check_docs() step by step.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1489582656-31133-35-git-send-email-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1489582656-31133-34-git-send-email-armbru@redhat.com>
Move the check whether the doc matches the expression name from
check_definition_doc() to check_exprs(). This changes the error
location from the comment to the expression. Makes sense as the
message talks about the expression: "Definition of '%s' follows
documentation for '%s'". It's also a step towards getting rid of
check_docs().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1489582656-31133-33-git-send-email-armbru@redhat.com>
This fixes the errors uncovered by the previous commit.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1489582656-31133-32-git-send-email-armbru@redhat.com>
New tests doc-before-include.json and doc-before-pragma.json show we
fail to reject a misplaced expression comment.
New test doc-no-symbol.json shows a bad error message.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1489582656-31133-31-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
We traditionally mark optional members #optional in the doc comment.
Before commit 3313b61, this was entirely manual.
Commit 3313b61 added some automation because its qapi2texi.py relied
on #optional to determine whether a member is optional. This is no
longer the case since the previous commit: the only thing qapi2texi.py
still does with #optional is stripping it out. We still reject bogus
qapi-schema.json and six places for qga/qapi-schema.json.
Thus, you can't actually rely on #optional to see whether something is
optional. Yet we still make people add it manually. That's just
busy-work.
Drop the code to check, fix up and strip out #optional, along with all
instances of #optional. To keep it out, add code to reject it, to be
dropped again once the dust settles.
No change to generated documentation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1489582656-31133-18-git-send-email-armbru@redhat.com>
Common Python pitfall: 'assert base_members' fires on [] in addition
to None. Correct to 'assert base_members is not None'.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1489582656-31133-10-git-send-email-armbru@redhat.com>
The new test case shows off qapi.py choking on an empty union base.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1489582656-31133-9-git-send-email-armbru@redhat.com>
qapi.py has a hardcoded white-list of type names that may violate the
rule on use of upper and lower case. Add a new pragma directive
'name-case-whitelist', and use it to replace the hard-coded
white-list.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1489582656-31133-7-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
qapi.py has a hardcoded white-list of command names that may violate
the rules on permitted return types. Add a new pragma directive
'returns-whitelist', and use it to replace the hard-coded white-list.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1489582656-31133-6-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This reverts commit 3313b61's changes to tests/qapi-schema/, except
for tests/qapi-schema/doc-*.
We could keep some of these doc comments to serve as positive test
cases. However, they don't actually add to what we get from doc
comment use in actual schemas, as we we don't test output matches
expectations, and don't systematically cover doc comment features.
Proper positive test coverage would be nice.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1489582656-31133-4-git-send-email-armbru@redhat.com>
Since we added the documentation generator in commit 3313b61, doc
comments are mandatory. That's a very good idea for a schema that
needs to be documented, but has proven to be annoying for testing.
Make doc comments optional again, but add a new directive
{ 'pragma': { 'doc-required': true } }
to let a QAPI schema require them.
Add test cases for the new pragma directive. While there, plug a
minor hole in includ directive test coverage.
Require documentation in the schemas we actually want documented:
qapi-schema.json and qga/qapi-schema.json.
We could probably make qapi2texi.py cope with incomplete
documentation, but for now, simply make it refuse to run unless the
schema has 'doc-required': true.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1489582656-31133-3-git-send-email-armbru@redhat.com>
[qapi-code-gen.txt wording tweaked]
Reviewed-by: Eric Blake <eblake@redhat.com>
The only functional difference between the GENERATED_HEADERS
and GENERATED_SOURCES variables is that 'Makefile' has a
dependancy on GENERATED_HEADERS, causing generated header files
to be created immediatey at the start of the build process.
There is no reason why this early creation should be restricted
to the .h files, and not include .c files too. Merge both of
the variables into a single GENERATED_FILES variable to make
it clear it is for any type of generated file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170228122901.24520-2-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
There is no change for now, because the callback just invokes
qemu_notify_event.
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The driver has failed to build since commit da34e65, in qemu 2.6,
due to a missing include of qapi/error.h for error_setg().
Since no one has complained in three releases, it is easier to
remove the dead code than to keep it around, especially since it
is not being built by default and therefore prone to bitrot.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Version: GnuPG v2
iQEtBAABCAAXBQJYwlKaEBxmYW16QHJlZGhhdC5jb20ACgkQyjViTGqRccbBJAgA
lMNWZUwpYakCc+WOL10KJD/s3fIfhzpBOjqdZMglLSBduZd8VmiC0icqT0WMKWA5
ceVXoppXR6Z3kGZja2TDggv6J0Qzra769phCQTbAwwHr22iC8MpyVbJ/lU4lW84O
nv/j3YR7NdLCASXODAq8cg0H/bo/1BpXOYdHARyevFH50029P4ErbFzZK6F3bBZ4
Wme3t3WNq/GTkIV9FVl3E1mjHu+3AzqdPOlgEkPXSOlN5HjdV36Z7xlPCmYaMyMx
nASvOkGHILz+d3A+q3khMsmsKOIWl+KSbMY6AH8KdOq9O6NYmTYmf2n9rSjm8Y+e
9m/r4g7EYIYgO2Zq2XNKlg==
=TerW
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/famz/tags/docker-pull-request' into staging
# gpg: Signature made Fri 10 Mar 2017 07:15:38 GMT
# gpg: using RSA key 0xCA35624C6A9171C6
# gpg: Good signature from "Fam Zheng <famz@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 5003 7CB7 9706 0F76 F021 AD56 CA35 624C 6A91 71C6
* remotes/famz/tags/docker-pull-request:
docker/dockerfiles/debian-s390-cross: include clang
tests/docker: support proxy / corporate firewall
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It's a silly little limitation on Shippable that is looks for clang
in the container even though we won't use it. The arm/aarch64 cross
builds inherit this from debian.docker but as we needed to use
debian-testing for this we add it here. We also collapse the update
step into one RUN line to remove and intermediate layer of the docker
build.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20170306112848.659-1-alex.bennee@linaro.org>
Signed-off-by: Fam Zheng <famz@redhat.com>
Additionally permit non-negative integers as key components. A
dictionary's keys must either be all integers or none. If all keys
are integers, convert the dictionary to a list. The set of keys must
be [0,N].
Examples:
* list.1=goner,list.0=null,list.1=eins,list.2=zwei
is equivalent to JSON [ "null", "eins", "zwei" ]
* a.b.c=1,a.b.0=2
is inconsistent: a.b.c clashes with a.b.0
* list.0=null,list.2=eins,list.2=zwei
has a hole: list.1 is missing
Similar design flaw as for objects: there is no way to denote an empty
list. While interpreting "key absent" as empty list seems natural
(removing a list member from the input string works when there are
multiple ones, so why not when there's just one), it doesn't work:
"key absent" already means "optional list absent", which isn't the
same as "empty list present".
Update the keyval object visitor to use this a.0 syntax in error
messages rather than the usual a[0].
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1488317230-26248-25-git-send-email-armbru@redhat.com>
[Off-by-one fix squashed in, as per Kevin's review]
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Until now, key components are separated by '.'. This leaves little
room for evolving the syntax, and is incompatible with the __RFQDN_
prefix convention for downstream extensions.
Since key components will be commonly used as QAPI member names by the
QObject input visitor, we can just as well borrow the QAPI naming
rules here: letters, digits, hyphen and period starting with a letter,
with an optional __RFQDN_ prefix for downstream extensions.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <1488317230-26248-20-git-send-email-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488317230-26248-19-git-send-email-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <1488317230-26248-18-git-send-email-armbru@redhat.com>
qmp_deserialize() calls qobject_from_json() ignoring errors. It
passes the result to qobject_input_visitor_new(), which asserts it's
not null. Therefore, we can just as well pass &error_abort to
qobject_from_json().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <1488317230-26248-16-git-send-email-armbru@redhat.com>
Pass &error_abort with known-good input. Else pass &err and check
what comes back. This demonstrates that the parser fails silently for
many errors.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <1488317230-26248-15-git-send-email-armbru@redhat.com>
The next few commits will put the errors to use where appropriate.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488317230-26248-13-git-send-email-armbru@redhat.com>
visitor_input_test_init_internal() parses test input with
qobject_from_jsonv(), and asserts it succeeds. Pass &error_abort for
good measure.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <1488317230-26248-12-git-send-email-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <1488317230-26248-10-git-send-email-armbru@redhat.com>
The next few commits will put the errors to use where appropriate.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <1488317230-26248-9-git-send-email-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <1488317230-26248-6-git-send-email-armbru@redhat.com>
Currently the QObjectInputVisitor assumes that all scalar values are
directly represented as the final types declared by the thing being
visited. i.e. it assumes an 'int' is using QInt, and a 'bool' is using
QBool, etc. This is good when QObjectInputVisitor is fed a QObject
that came from a JSON document on the QMP monitor, as it will strictly
validate correctness.
To allow QObjectInputVisitor to be reused for visiting a QObject
originating from keyval_parse(), an alternative mode is needed where
all the scalars types are represented as QString and converted on the
fly to the final desired type.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1475246744-29302-8-git-send-email-berrange@redhat.com>
Rebased, conflicts resolved, commit message updated to refer to
keyval_parse(). autocast replaced by keyval in identifiers,
noautocast replaced by fail in tests.
Fix qobject_input_type_uint64_keyval() not to reject '-', for QemuOpts
compatibility: replace parse_uint_full() by open-coded
parse_option_number(). The next commit will add suitable tests.
Leave out the fancy ERANGE error reporting for now, but add a TODO
comment. Add it qobject_input_type_int64_keyval() and
qobject_input_type_number_keyval(), too.
Open code parse_option_bool() and parse_option_size() so we have to
call qobject_input_get_name() only when actually needed. Again, leave
out ERANGE error reporting for now.
QAPI/QMP downstream extension prefixes __RFQDN_ don't work, because
keyval_parse() splits them at '.'. This will be addressed later in
the series.
qobject_input_type_int64_keyval(), qobject_input_type_uint64_keyval(),
qobject_input_type_number_keyval() tweaked for style.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <1488317230-26248-5-git-send-email-armbru@redhat.com>
keyval_parse() parses KEY=VALUE,... into a QDict. Works like
qemu_opts_parse(), except:
* Returns a QDict instead of a QemuOpts (d'oh).
* Supports nesting, unlike QemuOpts: a KEY is split into key
fragments at '.' (dotted key convention; the block layer does
something similar on top of QemuOpts). The key fragments are QDict
keys, and the last one's value is updated to VALUE.
* Each key fragment may be up to 127 bytes long. qemu_opts_parse()
limits the entire key to 127 bytes.
* Overlong key fragments are rejected. qemu_opts_parse() silently
truncates them.
* Empty key fragments are rejected. qemu_opts_parse() happily
accepts empty keys.
* It does not store the returned value. qemu_opts_parse() stores it
in the QemuOptsList.
* It does not treat parameter "id" specially. qemu_opts_parse()
ignores all but the first "id", and fails when its value isn't
id_wellformed(), or duplicate (a QemuOpts with the same ID is
already stored). It also screws up when a value contains ",id=".
* Implied value is not supported. qemu_opts_parse() desugars "foo" to
"foo=on", and "nofoo" to "foo=off".
* An implied key's value can't be empty, and can't contain ','.
I intend to grow this into a saner replacement for QemuOpts. It'll
take time, though.
Note: keyval_parse() provides no way to do lists, and its key syntax
is incompatible with the __RFQDN_ prefix convention for downstream
extensions, because it blindly splits at '.', even in __RFQDN_. Both
issues will be addressed later in the series.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1488317230-26248-4-git-send-email-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <1488317230-26248-3-git-send-email-armbru@redhat.com>
qemu_opts_parse() interprets "no" as negated empty key. Consistent
with its acceptance of empty keys elsewhere, whatever that's worth.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <1488317230-26248-2-git-send-email-armbru@redhat.com>
if ftp_proxy/http_proxy/https_proxy standard environment variables available,
pass them to the docker daemon to build images.
this is required when building behind corporate proxy/firewall, but also help
when using local cache server (ie: apt/yum).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20170306205520.32311-1-f4bug@amsat.org>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
The qga/get-vcpus test fails in a simple chroot environment, as
used in an openSUSE Build Service local build, so first check
that the sysfs based path exists in order to avoid calling this
test in an environment where it won't work right.
Signed-off-by: Bruce Rogers <brogers@suse.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-28-git-send-email-armbru@redhat.com>
When you try to visit beyond the end of a list, the qobject input
visitor crashes, and the string visitor screws returns garbage. The
generated list visits never go beyond the list end, but manual visits
could.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-27-git-send-email-armbru@redhat.com>
Fix the design flaw demonstrated in the previous commit: new method
check_list() lets input visitors report that unvisited input remains
for a list, exactly like check_struct() lets them report that
unvisited input remains for a struct or union.
Implement the method for the qobject input visitor (straightforward),
and the string input visitor (less so, due to the magic list syntax
there). The opts visitor's list magic is even more impenetrable, and
all I can do there today is a stub with a FIXME comment. No worse
than before.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1488544368-30622-26-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1488544368-30622-25-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Demonstrates a design flaw: there is no way to for input visitors to
report that a list visit didn't visit the complete input list. The
generated list visits always do, but manual visits needn't.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-24-git-send-email-armbru@redhat.com>
Lists with elements above INT64_MAX don't work (known bug). Empty
lists don't work (weird).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-23-git-send-email-armbru@redhat.com>
Call visitor_input_teardown() from visitor_input_test_init(), so you
don't have to call it from the actual tests.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-22-git-send-email-armbru@redhat.com>
Much of test-qobject-input-strict.c duplicates
test-qobject-input-strict.c, but with less assertions on expected
output:
* test_validate_struct() duplicates test_visitor_in_struct()
* test_validate_struct_nested() duplicates
test_visitor_in_struct_nested()
* test_validate_list() duplicates the first half of
test_visitor_in_list()
* test_validate_union_native_list() duplicates
test_visitor_in_native_list_int()
* test_validate_union_flat() duplicates test_visitor_in_union_flat()
* test_validate_alternate() duplicates the first part of
test_visitor_in_alternate()
Merge the remaining test cases into test-qobject-input-visitor.c, and
drop the now redundant test-qobject-input-strict.c.
Test case "/visitor/input-strict/fail/list" isn't really about lists,
it's about a bad struct nested in a list. Rename accordingly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-21-git-send-email-armbru@redhat.com>
The split between tests/test-qobject-input-visitor.c and
tests/test-qobject-input-strict.c now makes less sense than ever. The
next commit will take care of that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-20-git-send-email-armbru@redhat.com>
The qobject input visitor comes in a strict and a non-strict variant.
This test is the non-strict variant's last user. Turns out it relies
on non-strict only in test_visitor_in_null(), and just out of
laziness. We don't actually test the non-strict behavior.
Clean up test_visitor_in_null(), and switch to the strict variant.
The next commit will drop the non-strict variant.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-19-git-send-email-armbru@redhat.com>
The QObject input visitor has three error message formats:
* Parameter '%s' is missing
* "Invalid parameter type for '%s', expected: %s"
* "QMP input object member '%s' is unexpected"
The '%s' are member names (or "null", but I'll fix that later).
The last error message calls the thing "QMP input object member"
instead of "parameter". Misleading when the visitor is used on
QObjects that don't come from QMP. Change it to "Parameter '%s' is
unexpected".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-12-git-send-email-armbru@redhat.com>
The command registry encapsulates a single command list. Give the
functions using it a parameter instead. Define suitable command lists
in monitor, guest agent and test-qmp-commands.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1488544368-30622-6-git-send-email-armbru@redhat.com>
[Debugging turds buried]
Reviewed-by: Eric Blake <eblake@redhat.com>
The way we get QMP commands registered is high tech:
* qapi-commands.py generates qmp_init_marshal() that does the actual work
* it also generates the magic to register it as a MODULE_INIT_QAPI
function, so it runs when someone calls
module_call_init(MODULE_INIT_QAPI)
* main() calls module_call_init()
QEMU needs to register a few non-qapified commands. Same high tech
works: monitor.c has its own qmp_init_marshal() along with the magic
to make it run in module_call_init(MODULE_INIT_QAPI).
QEMU also needs to unregister commands that are not wanted in this
build's configuration (commit 5032a16). Simple enough:
qmp_unregister_commands_hack(). The difficulty is to make it run
after the generated qmp_init_marshal(). We can't simply run it in
monitor.c's qmp_init_marshal(), because the order in which the
registered functions run is indeterminate. So qmp_init_marshal()
registers qmp_unregister_commands_hack() separately. Since
registering *appends* to the list of registered functions, this will
make it run after all the functions that have been registered already.
I suspect it takes a long and expensive computer science education to
not find this silly.
Dumb it down as follows:
* Drop MODULE_INIT_QAPI entirely
* Give the generated qmp_init_marshal() external linkage.
* Call it instead of module_call_init(MODULE_INIT_QAPI)
* Except in QEMU proper, call new monitor_init_qmp_commands() that in
turn calls the generated qmp_init_marshal(), registers the
additional commands and unregisters the unwanted ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-5-git-send-email-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-4-git-send-email-armbru@redhat.com>
The next commit is going to add a test that calls qmp("null").
Curiously, this hangs. Here's why.
qmp_fd_sendv() doesn't send newlines. Not even when @fmt contains
some. At first glance, the QMP parser seems to be fine with that.
However, it turns out that it fails to react to input until it sees
either a newline, an object or an array. To reproduce, feed to a QMP
monitor like this:
$ echo -n 'null' | socat UNIX:/work/armbru/images/test-qmp STDIO
{"QMP": {"version": {"qemu": {"micro": 50, "minor": 8, "major": 2}, "package": " (v2.8.0-1195-gf84141e-dirty)"}, "capabilities": []}}
No output after the greeting.
Add a newline:
$ echo 'null' | socat UNIX:/work/armbru/images/test-qmp STDIO
{"QMP": {"version": {"qemu": {"micro": 50, "minor": 8, "major": 2}, "package": " (v2.8.0-1195-gf84141e-dirty)"}, "capabilities": []}}
{"error": {"class": "GenericError", "desc": "Expected 'object' in QMP input"}}
Correct output for input 'null'.
Add an object instead:
$ echo -n 'null { "execute": "qmp_capabilities" }' | socat UNIX:qmp-socket STDIO
{"QMP": {"version": {"qemu": {"micro": 50, "minor": 8, "major": 2}, "package": " (v2.8.0-1195-gf84141e-dirty)"}, "capabilities": []}}
{"error": {"class": "GenericError", "desc": "Expected 'object' in QMP input"}}
{"return": {}}
Also correct output.
Work around this QMP bug by having qmp_fd_sendv() append a newline.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-3-git-send-email-armbru@redhat.com>
This will probably be my last pull request before the hard freeze. It
has some new work, but that has all been posted in draft before the
soft freeze, so I think it's reasonable to include in qemu-2.9.
This batch has:
* A substantial amount of POWER9 work
* Implements the legacy (hash) MMU for POWER9
* Some more preliminaries for implementing the POWER9 radix
MMU
* POWER9 has_work
* Basic POWER9 compatibility mode handling
* Removal of some premature tests
* Some cleanups and fixes to the existing MMU code to make the
POWER9 work simpler
* A bugfix for TCG multiply adds on power
* Allow pseries guests to access PCIe extended config space
This also includes a code-motion not strictly in ppc code - moving
getrampagesize() from ppc code to exec.c. This will make some future
VFIO improvements easier, Paolo said it was ok to merge via my tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PcNw
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170303' into staging
ppc patch queuye for 2017-03-03
This will probably be my last pull request before the hard freeze. It
has some new work, but that has all been posted in draft before the
soft freeze, so I think it's reasonable to include in qemu-2.9.
This batch has:
* A substantial amount of POWER9 work
* Implements the legacy (hash) MMU for POWER9
* Some more preliminaries for implementing the POWER9 radix
MMU
* POWER9 has_work
* Basic POWER9 compatibility mode handling
* Removal of some premature tests
* Some cleanups and fixes to the existing MMU code to make the
POWER9 work simpler
* A bugfix for TCG multiply adds on power
* Allow pseries guests to access PCIe extended config space
This also includes a code-motion not strictly in ppc code - moving
getrampagesize() from ppc code to exec.c. This will make some future
VFIO improvements easier, Paolo said it was ok to merge via my tree.
# gpg: Signature made Fri 03 Mar 2017 03:20:36 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170303:
target/ppc: rewrite f[n]m[add,sub] using float64_muladd
spapr: Small cleanup of PPC MMU enums
spapr_pci: Advertise access to PCIe extended config space
target/ppc: Rework hash mmu page fault code and add defines for clarity
target/ppc: Move no-execute and guarded page checking into new function
target/ppc: Add execute permission checking to access authority check
target/ppc: Add Instruction Authority Mask Register Check
hw/ppc/spapr: Add POWER9 to pseries cpu models
target/ppc/POWER9: Add cpu_has_work function for POWER9
target/ppc/POWER9: Add POWER9 pa-features definition
target/ppc/POWER9: Add POWER9 mmu fault handler
target/ppc: Don't gen an SDR1 on POWER9 and rework register creation
target/ppc: Add patb_entry to sPAPRMachineState
target/ppc/POWER9: Add POWERPC_MMU_V3 bit
powernv: Don't test POWER9 CPU yet
exec, kvm, target-ppc: Move getrampagesize() to common code
target/ppc: Add POWER9/ISAv3.00 to compat_table
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virtio support for region caches broke a bunch of stuff - fixing most of
it though it's not ideal. Still pondering the right way to fix it.
New: VM gen ID and hotplug for PXB.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYt7llAAoJECgfDbjSjVRp+r4H/1cmQ4F67H8oSOAT8xuAQFku
OdHoVRJMWf7CRvZ7JqVke/a877d+h6ZpfW5dZQ7hp7O7rkPiuPHa5PVb0WGwDqrD
scSOIvDPxJm19pnfZoF4zx+Ov45W5ahF+gwwm/sJU232ApLqOmAjs0FUxidkadQE
f5Jrjs20WO2Vkkcd3U7Zl31myre0V7AbwIm7dB/8B+dpL6bJcxSvlM4krwLdBY6S
lLs9V6ypRzjUxS3MDANL75KNrO/zys55J+Pa4sEh4+H0OX71v9Icl3s1zaM8J/EN
VPjdqhDvJuEahc50FbJyRZQGIzOZ6PcGMsKUHKlxoVmDYZ6Pv5lOnpaLZRT6HMk=
=ITdO
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pc: fixes, features
virtio support for region caches broke a bunch of stuff - fixing most of
it though it's not ideal. Still pondering the right way to fix it.
New: VM gen ID and hotplug for PXB.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 02 Mar 2017 06:19:17 GMT
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
hw/pxb-pcie: fix PCI Express hotplug support
tests/acpi: update DSDT after last patch
acpi: simplify _OSC
virtio: unbreak virtio-pci with IOMMU after caching ring translations
virtio: add missing region cache init in virtio_load()
virtio: invalidate memory in vring_set_avail_event()
virtio: guard vring access when setting notification
virtio: check for vring setup in virtio_queue_empty
MAINTAINERS: Add VM Generation ID entries
tests: Move reusable ACPI code into a utility file
qmp/hmp: add query-vm-generation-id and 'info vm-generation-id' commands
ACPI: Add Virtual Machine Generation ID support
ACPI: Add vmgenid blob storage to the build tables
docs: VM Generation ID device description
linker-loader: Add new 'write pointer' command
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A couple of tests for the work-in-progress 'powernv' machine type attempt
to test on POWER9 CPUs. However the POWER9 CPU support is incomplete and
this doesn't really work. In particular the firmware image we have
currently assumes the presence of the SDR1 register, which no longer exists
on POWER9. We only got away with this so far, because of a different bug
which added SDR1 to POWER9 even though it shouldn't be there.
For now, remove POWER9 testing of powernv, POWER8 testing will do for now
until the POWER9 support is more complete.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Note: The 'postcopy: Update userfaultfd.h header' is part of
Paolo's header update and will disappear if applied after it.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
-----BEGIN PGP SIGNATURE-----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=PCYv
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20170228a' into staging
Migration pull
Note: The 'postcopy: Update userfaultfd.h header' is part of
Paolo's header update and will disappear if applied after it.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
# gpg: Signature made Tue 28 Feb 2017 12:38:34 GMT
# gpg: using RSA key 0x0516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20170228a: (27 commits)
postcopy: Add extra check for COPY function
postcopy: Add doc about hugepages and postcopy
postcopy: Check for userfault+hugepage feature
postcopy: Update userfaultfd.h header
postcopy: Allow hugepages
postcopy: Send whole huge pages
postcopy: Mask fault addresses to huge page boundary
postcopy: Load huge pages in one go
postcopy: Use temporary for placing zero huge pages
postcopy: Plumb pagesize down into place helpers
postcopy: Record largest page size
postcopy: enhance ram_block_discard_range for hugepages
exec: ram_block_discard_range
postcopy: Chunk discards for hugepages
postcopy: Transmit and compare individual page sizes
postcopy: Transmit ram size summary word
migration: fix use-after-free of to_dst_file
migration: Update docs to discourage version bumps
migration: fix id leak regression
migrate: Introduce a 'dc->vmsd' check to avoid segfault for --only-migratable
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Also usable by upcoming VM Generation ID tests
Signed-off-by: Ben Warren <ben@skyportsystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=g3ew
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches
# gpg: Signature made Tue 28 Feb 2017 20:35:32 GMT
# gpg: using RSA key 0x7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (46 commits)
block: Add Error parameter to bdrv_append()
block: Add Error parameter to bdrv_set_backing_hd()
block: Assertions for resize permission
block: Assertions for write permissions
block: Pass BdrvChild to bdrv_aligned_preadv/pwritev and copy-on-read
tests: Remove FIXME comments
nbd/server: Use real permissions for NBD exports
migration/block: Use real permissions
hmp: Request permissions in qemu-io
commit: Add filter-node-name to block-commit
mirror: Add filter-node-name to blockdev-mirror
stream: Use real permissions in streaming block job
mirror: Use real permissions in mirror/active commit block job
blockjob: Factor out block_job_remove_all_bdrv()
block: Allow backing file links in change_parent_backing_link()
block: BdrvChildRole.attach/detach() callbacks
block: Fix pending requests check in bdrv_append()
backup: Use real permissions in backup block job
commit: Use real permissions for HMP 'commit'
commit: Use real permissions in commit block job
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Version: GnuPG v2
iQEtBAABCAAXBQJYtW+gEBxmYW16QHJlZGhhdC5jb20ACgkQyjViTGqRccagwgf/
QjBnAloOFjDYDKN328CHMwB6tuhkjqv5XrTm5UXz9SIW+x/pIHPIG7monxTVAfUa
rjUwN5HlP2lcsuXBuuEIi0xStqFbcjpuLeKNP/TCBcYusJ0DT7Rqi/gU3mGGLzSZ
MTnzGDQIc0lsRwxkXLFlnkaAhd237+9KofSqg/Ohel1k1gLrT0hQlQpnsMOk7eag
ihn2zgzgJ6d04DuD/oRTpW4hd7WezfgCPNmc7BvZNb1tbxjBwP3TmnF49ZGL0z1p
SGx5ym+yBVoP6cnB0cXIuWeKIRgIpGaBefg8ksqbRkJf6ExXrBcgi2VIvdNq+HZ7
BMdVCUYDv5kQi6JpkQpwAg==
=5cxL
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/famz/tags/docker-pull-request' into staging
# gpg: Signature made Tue 28 Feb 2017 12:40:00 GMT
# gpg: using RSA key 0xCA35624C6A9171C6
# gpg: Good signature from "Fam Zheng <famz@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 5003 7CB7 9706 0F76 F021 AD56 CA35 624C 6A91 71C6
* remotes/famz/tags/docker-pull-request:
.shippable: add s390x-cross target
new: dockerfiles/debian-s390-cross
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use qvirtio_pci_device_find_slot() to avoid leaking the non-hp
device. Add assert() to avoid further leaks in the future.
Use qvirtio_pci_device_free() to correctly free QVirtioPCIDevice.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Allow specifying which slot to look for the device.
This will be used in the following patch to avoid leaking when multiple
devices exists and we want to lookup the hotplug one.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
pci_init() shouldn't be a test function, but instead called before any
test. This allows to run a single test with -p /x86_64/ehci/....
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Spotted by ASAN.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Spotted by ASAN.
This hunk adds an assertion. It checks that we're finding no more than
one e1000e device: each hit allocates, but there is only one g_free().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The inside array should be free too.
Spotted by ASAN.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Move the fallback from qtest_add_data_func_full() to glib-compat.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
No need for strdup, fix leaks when socat is missing.
Spotted by ASAN.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: "Daniel P. Berrange" <berrange@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Aborting on error in bdrv_append() isn't correct. This patch fixes it
and lets the callers handle failures.
Test case 085 needs a reference output update. This is caused by the
reversed order of bdrv_set_backing_hd() and change_parent_backing_link()
in bdrv_append(): When the backing file of the new node is set, the
parent nodes are still pointing to the old top, so the backing blocker
is now initialised with the node name rather than the BlockBackend name.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Not requesting any permissions is actually correct for these test cases
because no actual I/O or other operation covered by the permission
system is performed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
The mirror block job is mainly used for two different scenarios:
Mirroring to an otherwise unused, independent target node, or for active
commit where the target node is part of the backing chain of the source.
Similarly to the commit block job patch, we need to insert a new filter
node to keep the permissions correct during active commit.
Note that one change this implies is that job->blk points to
mirror_top_bs as its root now, and mirror_top_bs (rather than the actual
source node) contains the bs->job pointer. This requires qemu-img commit
to get the job by name now rather than just taking bs->job.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Acked-by: Max Reitz <mreitz@redhat.com>
The backup block job doesn't have very complicated requirements: It
needs to read from the source and write to the target, but it's fine
with either side being changed. The only restriction is that we can't
resize the image because the job uses a cached value.
qemu-iotests 055 needs to be changed because it used a target which was
already attached to a virtio-blk device. The permission system correctly
forbids this (virtio-blk can't accept another writer with its default
share-rw=off).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
This functions creates a BlockBackend internally, so the block jobs need
to tell it what they want to do with the BB.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
By default, don't allow another writer for block devices that are
attached to a guest device. For the cases where this setup is intended
(e.g. using a cluster filesystem on the disk), the new option can be
used to allow it.
This change affects only devices using DEFINE_BLOCK_PROPERTIES().
Devices directly using DEFINE_PROP_DRIVE() still accept writers
unconditionally.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
This makes all device emulations with a qdev drive property request
permissions on their BlockBackend. The only thing we block at this point
is resizing images for some devices that can't support it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Now that blk_insert_bs() requests the BlockBackend permissions for the
node it attaches to, it can fail. Instead of aborting, pass the errors
to the callers.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
We want every user to be specific about the permissions it needs, so
we'll pass the initial permissions as parameters to blk_new(). A user
only needs to call blk_set_perm() if it wants to change the permissions
after the fact.
The permissions are stored in the BlockBackend and applied whenever a
BlockDriverState should be attached in blk_insert_bs().
This does not include actually choosing the right set of permissions
everywhere yet. Instead, the usual FIXME comment is added to each place
and will be addressed in individual patches.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Commit 75cdcd1 neglected to update tests/qemu-iotests/049.out, and
made the error message for negative size worse. Fix that.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds an s390 cross build target to our library of docker setups.
There is an issue with the xfslibs-dev:s390x package having a clash so
we do a || apt-get -f install to fixup the rest of the dependencies.
This doesn't build on the debian.docker file as we are using the
multilib compiler which is only available in stretch (the current
testing repo).
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20170227143028.16428-2-alex.bennee@linaro.org>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Let's have a test for ptr arrays to some primitive type with some
not-null and null ptrs intermixed.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170222160119.52771-6-pasic@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add test for VMSTATE_ARRAY_OF_POINTER_TO_STRUCT with an array
containing some null pointer.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170222160119.52771-5-pasic@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixed type case in assert to uintptr_t rather than uint64_t
The 32-bit TCG bug has been fixed a while ago, so we can enable
this test for sparc64 now, too. Unfortunately, OpenBIOS does not
work with the sun4v machine anymore (it needs to catch up with the
improved emulation), so we can only enable this test for the sun4u
machine right now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
trivial: initialize the dirty buffer with a random-ish byte.
Stops valgrind from whining about uninitialized buffers.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
nodes[id].next is written by other threads. If atomic_read is not used
(matching atomic_set in mcs_mutex_lock!) the compiler can optimize the
whole "if" away!
Reported-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Greg Kurz <groug@kaod.org>
Message-id: 20170227111726.9237-1-pbonzini@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=OYgF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches
# gpg: Signature made Fri 24 Feb 2017 18:08:26 GMT
# gpg: using RSA key 0x7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream:
tests: Use opened block node for block job tests
vvfat: Use opened node as backing file
block: Add bdrv_new_open_driver()
block: Factor out bdrv_open_driver()
block: Use BlockBackend for image probing
block: Factor out bdrv_open_child_bs()
block: Attach bs->file only during .bdrv_open()
block: Pass BdrvChild to bdrv_truncate()
mirror: Resize active commit base in mirror_run()
qcow2: Use BB for resizing in qcow2_amend_options()
blockdev: Use BlockBackend to resize in qmp_block_resize()
iotests: Fix another race in 030
qemu-img: Improve documentation for PREALLOC_MODE_FALLOC
qemu-img: Truncate before full preallocation
qemu-img: Add tests for raw image preallocation
qemu-img: Do not truncate before preallocation
qemu-iotests: redirect nbd server stdout to /dev/null
qemu-iotests: add ability to exclude certain protocols from tests
qemu-iotests: Test 137 only supports 'file' protocol
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Hi Peter,
These are testing and build automation patches:
- Shippable.com powered CI config
- Docker cross build
- Fixes and MAINTAINERS tweaks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEtBAABCAAXBQJYr9MuEBxmYW16QHJlZGhhdC5jb20ACgkQyjViTGqRccb9cQf9
FRjpMS0LP0IGTF6YkURivG09bPsl9owGfiZjRNo2DnEFmATY+aOoSvJMNyUBGwsi
k9I1AgWZ6VPob4TDqDnPWHaNGNGLb7quP0rMN/Q2TvPGbmkevD4o7SX5cDCEPA/D
QLxvG/SYb1R6a9lEmmyPgk8Q7zwB3nVAITvQMLVwVgzGk8t6uDNHBt+Fckf4zyJL
XbuKYqAgICRGMDhuqqF9IkVO7wHCS3Gh0SqNKDMEZPeEgnWjFbyjsZxIJihk7tZP
ZFCLEtnNYmNZmeFAJCL8p7PvsnXHF0lcWTIVzC5FOjPu9ytmcqw3GmgvghmCjFrG
aGH8BYguc+SmQOUqtnR4lA==
=JQKW
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/famz/tags/for-upstream' into staging
Docker testing and shippable patches
Hi Peter,
These are testing and build automation patches:
- Shippable.com powered CI config
- Docker cross build
- Fixes and MAINTAINERS tweaks.
# gpg: Signature made Fri 24 Feb 2017 06:31:10 GMT
# gpg: using RSA key 0xCA35624C6A9171C6
# gpg: Good signature from "Fam Zheng <famz@redhat.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 5003 7CB7 9706 0F76 F021 AD56 CA35 624C 6A91 71C6
* remotes/famz/tags/for-upstream:
docker: Install python2 explicitly in docker image
MAINTAINERS: merge Build and test automation with Docker tests
.shippable.yml: new CI provider
new: debian docker targets for cross-compiling
tests/docker: add basic user mapping support
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=o8eA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-util-2017-02-23' into staging
option cutils: Fix and clean up number conversions
# gpg: Signature made Thu 23 Feb 2017 19:41:17 GMT
# gpg: using RSA key 0x3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-util-2017-02-23: (24 commits)
option: Fix checking of sizes for overflow and trailing crap
util/cutils: Change qemu_strtosz*() from int64_t to uint64_t
util/cutils: Return qemu_strtosz*() error and value separately
util/cutils: Let qemu_strtosz*() optionally reject trailing crap
qemu-img: Wrap cvtnum() around qemu_strtosz()
test-cutils: Drop suffix from test_qemu_strtosz_simple()
test-cutils: Use qemu_strtosz() more often
util/cutils: Drop QEMU_STRTOSZ_DEFSUFFIX_* macros
util/cutils: New qemu_strtosz()
util/cutils: Rename qemu_strtosz() to qemu_strtosz_MiB()
util/cutils: New qemu_strtosz_metric()
test-cutils: Cover qemu_strtosz() around range limits
test-cutils: Cover qemu_strtosz() with trailing crap
test-cutils: Cover qemu_strtosz() invalid input
test-cutils: Add missing qemu_strtosz()... endptr checks
option: Fix to reject invalid and overflowing numbers
util/cutils: Clean up control flow around qemu_strtol() a bit
util/cutils: Clean up variable names around qemu_strtol()
util/cutils: Rename qemu_strtoll(), qemu_strtoull()
util/cutils: Rewrite documentation of qemu_strtol() & friends
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
blk_insert_bs() and block job related functions will soon require an
opened block node (permission calculations will involve the block
driver), so let our tests be consistent with the real users in this
respect.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
The way that attaching bs->file worked was a bit unusual in that it was
the only child that would be attached to a node which is not opened yet.
Because of this, the block layer couldn't know yet which permissions the
driver would eventually need.
This patch moves the point where bs->file is attached to the beginning
of the individual .bdrv_open() implementations, so drivers already know
what they are going to do with the child. This is also more consistent
with how driver-specific children work.
For a moment, bdrv_open() gets its own BdrvChild to perform image
probing, but instead of directly assigning this BdrvChild to the BDS, it
becomes a temporary one and the node name is passed as an option to the
drivers, so that they can simply use bdrv_open_child() to create another
reference for their own use.
This duplicated child for (the not opened yet) bs is not the final
state, a follow-up patch will change the image probing code to use a
BlockBackend, which is completely independent of bs.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
We can't rely on a non-paused job to be present and running for us.
Assume that if the job is not present that it completed already.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
