The rename prepares for the patch after next's DEFINE_PROP_UNSIGNED().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170607163635.17635-16-marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Implement NVMe Controller Memory Buffers (CMBs) which were added in
version 1.2 of the NVMe Specification. This patch adds an optional
argument (cmb_size_mb) which indicates the size of the CMB (in
MB). Currently only the Submission Queue Support (SQS) is enabled
which aligns with the current Linux driver for NVMe.
Signed-off-by: Stephen Bates <sbates@raithlin.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
[hch: ported over from qemu-nvme.git to mainline]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Laszlo spotted and studied this wasteful "if". He pointed out:
The original virtio_blk_free_request needed an "if" as it accesses one
field, since 671ec3f056 ("virtio-blk: Convert VirtIOBlockReq.elem to
pointer", 2014-06-11); later on in f897bf751f ("virtio-blk: embed
VirtQueueElement in VirtIOBlockReq", 2014-07-09) the field became
embedded, so the "if" became unnecessary (at which point we were using
g_slice_free(), but it is the same.
Now drop it.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We now have macros in place to make it less verbose to add a scalar
to QDict and QList, so use them.
Patch created mechanically via:
spatch --sp-file scripts/coccinelle/qobject.cocci \
--macro-file scripts/cocci-macro-file.h --dir . --in-place
then touched up manually to fix a couple of '?:' back to original
spacing, as well as avoiding a long line in monitor.c.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20170427215821.19397-7-eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJY/5EdAAoJEIlPj0hw4a6QHj8P/1D3iZq8vKyLvnkioYC00ao8
dhuCFV1Dk0dl/QXvDXxNAHFqmHp2PzHeHF2V19bTbUh9QnY3WH9aSsMQ7YVPDzLb
6ZezbxXd1l8+IOrWh+ch+x6jiUpRAeHGjhSpFxQEmH5THBmPtLHBFhAeeGpVq6CT
MPFlN0mr1snyMMbK2aKCVTHgh5Wip83/t/kijIq4RmPwXdJbwxx55PL8jxC/NZHq
/NbAZzAT149fmItfBNnsRTfNoDs7fSmgM9VelYsnJNHs6qkYYfewxys4vudePG8n
ZcjCXMv9vdCSTfXfYY9nxhfGCgkkRSvBWrzARRIUPxTXGAmEU52LJrccpG9AEFRZ
Kgz1JYr0y+u/g+RsCJvAglvmciawXgZH8GIR4sFl2iv4u6cx8PxNRgjTdt7YX4Je
V7+scmOLB0U5wkI7PUcPV1v2fwKJHFfMdyik257otfMCJiTCnWGJfCZGR4JAdy3C
NHuG4eIj2XLjZ7IQIo3mg+EfdCWdfVMKtXj0MAFsP6Kcr6sY/ef5sx/wB61k3NU1
Y4ctI/LAOONsjlC2yzJ4aZR4LgyFcVcwx8FKOK7niCcCgVLYGWpyiHU3kFKYlmKM
FKIlGPPOK8WuRV9NUGDI9A8XENyFXGyiR2xGCotfgHj+FSSqRzhKH4ecfgNimJVY
wjTzZmBa68pLHdXaJ+SV
=OfeB
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/sstabellini/tags/xen-20170421-v2-tag' into staging
Xen 2017/04/21 + fix
# gpg: Signature made Tue 25 Apr 2017 19:10:37 BST
# gpg: using RSA key 0x894F8F4870E1AE90
# gpg: Good signature from "Stefano Stabellini <stefano.stabellini@eu.citrix.com>"
# gpg: aka "Stefano Stabellini <sstabellini@kernel.org>"
# Primary key fingerprint: D04E 33AB A51F 67BA 07D3 0AEA 894F 8F48 70E1 AE90
* remotes/sstabellini/tags/xen-20170421-v2-tag: (21 commits)
move xen-mapcache.c to hw/i386/xen/
move xen-hvm.c to hw/i386/xen/
move xen-common.c to hw/xen/
add xen-9p-backend to MAINTAINERS under Xen
xen/9pfs: build and register Xen 9pfs backend
xen/9pfs: send responses back to the frontend
xen/9pfs: implement in/out_iov_from_pdu and vmarshal/vunmarshal
xen/9pfs: receive requests from the frontend
xen/9pfs: connect to the frontend
xen/9pfs: introduce Xen 9pfs backend
9p: introduce a type for the 9p header
xen: import ring.h from xen
configure: use pkg-config for obtaining xen version
xen: additionally restrict xenforeignmemory operations
xen: use libxendevice model to restrict operations
xen: use 5 digit xen versions
xen: use libxendevicemodel when available
configure: detect presence of libxendevicemodel
xen: create wrappers for all other uses of xc_hvm_XXX() functions
xen: rename xen_modified_memory() to xen_hvm_modified_memory()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Do not use the ring.h header installed on the system. Instead, import
the header into the QEMU codebase. This avoids problems when QEMU is
built against a Xen version too old to provide all the ring macros.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
CC: anthony.perard@citrix.com
CC: jgross@suse.com
Today qemu is using e.g. the value 480 for Xen version 4.8.0. As some
Xen version tests are using ">" relations this scheme will lead to
problems when Xen version 4.10.0 is being reached.
Instead of the 3 digit schem use a 5 digit scheme (e.g. 40800 for
version 4.8.0).
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Change Makefile.objs to use CONFIG_XEN instead of CONFIG_XEN_BACKEND, so
that the Xen backends are only built for targets that support Xen.
Set CONFIG_XEN in the toplevel Makefile to ensure that files that are
built only once pick up Xen support properly.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Tested-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
CC: pbonzini@redhat.com
CC: peter.maydell@linaro.org
CC: rth@twiddle.net
CC: stefanha@redhat.com
Message-Id: <1489694518-16978-1-git-send-email-sstabellini@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By default, don't allow another writer for block devices that are
attached to a guest device. For the cases where this setup is intended
(e.g. using a cluster filesystem on the disk), the new option can be
used to allow it.
This change affects only devices using DEFINE_BLOCK_PROPERTIES().
Devices directly using DEFINE_PROP_DRIVE() still accept writers
unconditionally.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
This makes all device emulations with a qdev drive property request
permissions on their BlockBackend. The only thing we block at this point
is resizing images for some devices that can't support it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Some devices allow a media change between read-only and read-write
media. They need to adapt the permissions in their .change_media_cb()
implementation, which can fail. So add an Error parameter to the
function.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
We want every user to be specific about the permissions it needs, so
we'll pass the initial permissions as parameters to blk_new(). A user
only needs to call blk_set_perm() if it wants to change the permissions
after the fact.
The permissions are stored in the BlockBackend and applied whenever a
BlockDriverState should be attached in blk_insert_bs().
This does not include actually choosing the right set of permissions
everywhere yet. Instead, the usual FIXME comment is added to each place
and will be addressed in individual patches.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-16-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-15-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This covers both file descriptor callbacks and polling callbacks,
since they execute related code.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-14-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In virtio_queue_host_notifier_aio_poll, not all "!virtio_queue_empty()"
cases are making true progress.
Currently the offending one is virtio-scsi event queue, whose handler
does nothing if no event is pending. As a result aio_poll() will spin on
the "non-empty" VQ and take 100% host CPU.
Fix this by reporting actual progress from virtio queue aio handlers.
Reported-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Tested-by: Ed Swierk <eswierk@skyportsystems.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
msix_init() reports errors with error_report(), which is wrong when
it's used in realize(). The same issue was fixed for msi_init() in
commit 1108b2f. In order to make the API change as small as possible,
leave the return value check to later patch.
For some devices(like e1000e, vmxnet3, nvme) who won't fail because of
msix_init's failure, suppress the error report by passing NULL error
object.
Bonus: add comment for msix_init.
CC: Jiri Pirko <jiri@resnulli.us>
CC: Gerd Hoffmann <kraxel@redhat.com>
CC: Dmitry Fleytman <dmitry@daynix.com>
CC: Jason Wang <jasowang@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Hannes Reinecke <hare@suse.de>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are a number of unused trace events that
scripts/cleanup-trace-events.pl finds. The "hw/vfio/pci-quirks.c"
filename was typoed and "qapi/qapi-visit-core.c" was missing the qapi/
directory prefix.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170126171613.1399-3-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The trace-events for a given source file should generally
always live in the same directory as the source file.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170125161417.31949-3-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
For configurations of the pflash_cfi01 device which set it up with a
device-width not equal to the width (ie where we are emulating
multiple narrow flash devices wired up in parallel), we were giving
incorrect values in the CFI data table:
(1) the sector length entry should specify the sector length for a
single device, not the length for the overall collection of
devices
(2) the number of blocks per device must not be divided by the
number of devices because the resulting device size would not
match the overall size
(3) this then means that the overall write block size must be
modified depending on the number of devices because the entry is
per device and when the guest writes into the flash it
calculates the write size by using the CFI entry (write size
per device) multiplied by the number of chips.
(It would alternatively be possible to modify the write
block size in the CFI table (currently hardcoded at 2048) and
leave the overall write block size alone.)
This commit corrects these bugs, and adds a hw-compat property
to retain the old behaviour on 2.8 and earlier versions. (The
only board we have which uses this sort of flash config and
has machine versioning is the "virt" board -- the PC uses a
single flash device and so behaviour is unaffected whether
using old-multiple-chip-handling or not.)
Here is a configuration example from the vexpress board:
VEXPRESS_FLASH_SIZE = 64M
VEXPRESS_FLASH_SECT_SIZE 256K
num-blocks = VEXPRESS_FLASH_SIZE / VEXPRESS_FLASH_SECT_SIZE = 256
sector-length = 256K
width = 4
device-width = 2
The code will fill the CFI entry with the following entries:
num-blocks = 256
sector-length = 128K
writeblock_size = 2048
This results in two chips, each with 256 * 128K = 32M device size and
a write block size of 2048.
A sector erase will be sent to both chips, thus 256K must be erased.
When the guest sends a block write command, it will write 4096 bytes
data at once (2048 per device).
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: cleaned up and expanded commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
n25q00 and mt25q01 devices share the same JEDEC ID. The difference
between those two devices is number of dies and one bit in extended
JEDEC bytes. This commit adds proper entry for both devices by
introduction the number of dies and and new 25q00 entries.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-4-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Modern big flash NOR devices consist of more than one die.
Some of them do not support chip erase and instead have a die
erase command that can erase one die only. This commit adds
support for defining the number of dies in the chip, and adds
support for die erase command.
The NOR flash model is not strict, so no option to
disable chip erase has been added.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-3-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some flash chips have additional page program opcode that
takes only 4 byte address. This commit adds support
for such command in Qemu.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-2-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, all virtio devices bypass IOMMU completely. This is because
address_space_memory is assumed and used during DMA emulation. This
patch converts the virtio core API to use DMA API. This idea is
- introducing a new transport specific helper to query the dma address
space. (only pci version is implemented).
- query and use this address space during virtio device guest memory
accessing when iommu platform (VIRTIO_F_IOMMU_PLATFORM) was enabled
for this device.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-block@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In normal operation we should never attempt to put more
data into the data[] array than it can hold. However if the
SPI controller connected to us misbehaves then it can send
us a sequence of commands that attempt this. Since the
controller might be in the guest (if the hardware does SPI
via bit-banging), catch the possible overrun conditions and
reset the flash internal state, logging them as guest errors.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 20170107111631.24444-1-jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: rewrote commit message to be more exact about when
this can happen]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The guest does not need to kick the virtqueue while we are processing
it. This reduces the number of vmexits during periods of heavy I/O.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20161201192652.9509-8-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1480434248-27138-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The patch is to fix the confusing assert fail message caused by
un-initialized device structure (from bite sized tasks).
The bug can be reproduced by
./qemu-system-x86_64 -nographic -device cfi.pflash01
The CFI hardware is dynamically loaded by QOM realizing mechanism,
however the realizing function in pflash_cfi01_realize function
requires the device being initialized manually before calling, like
./qemu-system-x86_64 -nographic
-device cfi.pflash01,num-blocks=1024,sector-length=4096,name=testcard
Once the initializing parameters are left off in the command, it will
leave the device structure not initialized, which makes
pflash_cfi01_realize try to realize a zero-volume card, causing
/mnt/EXT_volume/projects/qemu/qemu-dev/exec.c:1378:
find_ram_offset: Assertion `size != 0\' failed.
Through my test, at least the flash device's block-number, sector-length
and its name is needed for pflash_cfi01_realize to behave correctly. So
I think the new asserts are needed to hint the QEMU user to specify
the device's parameters correctly.
Signed-off-by: Ziyue Yang <skiver.cloud.yzy@gmail.com>
Message-Id: <1481810693-13733-1-git-send-email-skiver.cloud.yzy@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ziyue Yang <yzylivezh@hotmail.com>
The guest sends discard requests as u64 sector/count pairs, but the
block layer operates internally with s64/s32 pairs. The conversion
leads to IO errors in the guest, the discard request is not processed.
domU.cfg:
'vdev=xvda, format=qcow2, backendtype=qdisk, target=/x.qcow2'
domU:
mkfs.ext4 -F /dev/xvda
Discarding device blocks: failed - Input/output error
Fix this by splitting the request into chunks of BDRV_REQUEST_MAX_SECTORS.
Add input range checking to avoid overflow.
Fixes f313520 ("xen_disk: add discard support")
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Dataplane has been omitting forever the step of setting ISR when
an interrupt is raised. This caused little breakage, because the
specification actually says that ISR may not be updated in MSI mode.
Some versions of the Windows drivers however didn't clear MSI mode
correctly, and proceeded using polling mode (using ISR, not the used
ring index!) for crashdump and hibernation. If it were just crashdump
and hibernation it would not be a big deal, but recent releases of
Windows do not really shut down, but rather log out and hibernate to
make the next startup faster. Hence, this manifested as a more serious
hang during shutdown with e.g. Windows 8.1 and virtio-win 1.8.0 RPMs.
Newer versions fixed this, while older versions do not use MSI at all.
The failure has always been there for virtio dataplane, but it became
visible after commits 9ffe337 ("virtio-blk: always use dataplane path
if ioeventfd is active", 2016-10-30) and ad07cd6 ("virtio-scsi: always
use dataplane path if ioeventfd is active", 2016-10-30) made virtio-blk
and virtio-scsi always use the dataplane code under KVM. The good news
therefore is that it was not a bug in the patches---they were doing
exactly what they were meant for, i.e. shake out remaining dataplane bugs.
The fix is not hard, so it's worth arranging for the broken drivers.
The virtio_should_notify+event_notifier_set pair that is common to
virtio-blk and virtio-scsi dataplane is replaced with a new public
function virtio_notify_irqfd that also sets ISR. The irqfd emulation
code now need not set ISR anymore, so virtio_irq is removed.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Override start_ioeventfd and stop_ioeventfd to start/stop the
whole dataplane logic. This has some positive side effects:
- no need anymore for virtio_add_queue_aio (i.e. a revert of
commit 0ff841f6d1)
- no need anymore to switch from generic ioeventfd handlers to
dataplane
It detects some errors better:
$ qemu-system-x86_64 -object iothread,id=io \
-drive id=null,file=null-aio://,if=none,format=raw \
-device virtio-blk-pci,ioeventfd=off,iothread=io,drive=null
qemu-system-x86_64: -device virtio-blk-pci,ioeventfd=off,iothread=io,drive=null:
ioeventfd is required for iothread
while previously it would have started just fine.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This simplifies the code and removes the ioeventfd_started
and ioeventfd_set_started callback. The only difference is
in how virtio-ccw handles an error---it doesn't disable
ioeventfd forever anymore. It was the only backend to do
so, and if desired this behavior should be implemented in
virtio-bus.c.
Instead of ioeventfd_started, the ioeventfd_assign callback now
determines whether the virtio bus supports host notifiers.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Prepare xen_be_send_notify to be shared with frontends:
* xen_be_send_notify -> xen_pv_send_notify
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Prepare xen_be_unbind_evtchn to be shared with frontends:
* xen_be_unbind_evtchn -> xen_pv_unbind_evtchn
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Prepare xen_be_printf to be used by both backend and frontends:
* xen_be_printf -> xen_pv_printf
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Fixes:
* WARNING: line over 80 characters
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
The condition '!A || (A && B)' is equivalent to '!A || B'.
Buglink: https://bugs.launchpad.net/qemu/+bug/1464611
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This makes the FloppyDrive qdev object actually useful: Now that it has
all properties that don't belong to the controller, you can actually
use '-device floppy' and get a working result.
Command line semantics is consistent with CD-ROM drives: By default you
get a single empty floppy drive. You can override it with -drive and
using the same index, but if you use -drive to add a floppy to a
different index, you get both of them. However, as soon as you use any
'-device floppy', even to a different slot, the default drive is
disabled.
Using '-device floppy' without specifying the unit will choose the first
free slot on the controller.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 1477386868-21826-4-git-send-email-kwolf@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Floppy controllers automatically create two floppy drive devices in qdev
now. (They always created two drives, but managed them only internally.)
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1477386868-21826-3-git-send-email-kwolf@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
This adds a qbus to the floppy controller that should contain the floppy
drives eventually. At the moment it just exists and is empty.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1477386868-21826-2-git-send-email-kwolf@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
The hard-coded default alignment is BDRV_SECTOR_SIZE, however this is not
necessarily the case for all platforms. Use this as the default alignment for
all current callers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-id: 1476445266-27503-2-git-send-email-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
