Some guests will use the standard MII status register
to verify link state. They will not notice link changes
unless this register is updated.
Verified with Linux 3.0 and Windows XP guests.
Without this patch, ethtool will report speed and duplex as
unknown when the link is down, but still report the link as
up. This is because the Linux e1000 driver checks the
mac_reg[STATUS] register link state before it checks speed
and duplex, but uses the phy_reg[PHY_STATUS] register for
the actual link state check. Fix by updating both registers
on link state changes.
Linux guest before:
(qemu) set_link e1000.0 off
kvm-sid:~# ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: Unknown!
Duplex: Unknown! (255)
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: umbg
Wake-on: d
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
(qemu) set_link e1000.0 on
Linux guest after:
(qemu) set_link e1000.0 off
[ 63.384221] e1000: eth0 NIC Link is Down
kvm-sid:~# ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: Unknown!
Duplex: Unknown! (255)
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: umbg
Wake-on: d
Current message level: 0x00000007 (7)
drv probe link
Link detected: no
(qemu) set_link e1000.0 on
[ 84.304582] e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add support for the RCC2 register on Fury class devices.
Based on a patch by Vijay Kumar.
Signed-off-by: Engin AYDOGAN <engin@bzzzt.biz>
[Peter Maydell: fixed comment typos, minor cleanup of unreachable code]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the PL061 to VMState. We choose to widen the struct members
to uint32_t rather than the other two options of breaking migration
compatibility or using vmstate hacks to read/write a 32 bit value
into an 8 bit struct field.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Versatile Express, Realview EB, PBX A9 and PB A8 boards all
use a PL111 for their graphics, not a PL110. Now we model the
PL111, use it on these board models.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On the Versatile PB, PL110 graphics adaptor only natively supports
5551 pixel format; an external mux swaps bits around to allow
RGB565 and BGR565, under the control of bits [1:0] in the SYS_CLCD
system register.
Implement these SYS_CLCD register bits, and use a gpio line to
feed them out of the system register model, across the versatilepb
board and into the pl110 so we can select the right format.
This is necessary as recent Linux versatile kernels default to
programming the CLCD and mux for 16 bit BGR rather than 16 bit RGB.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Model the PL111 CLCD controller. This is a minor variation
on the PL110; the major programmer visible differences are
support for hardware cursor (unimplemented) and two new
pixel formats.
Since syborg_fb.c borrows the pl11x pixel drawing routines,
we also update it to cope with the new slightly larger array
of function pointers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Other scsi_target_reqops commands were careful about not using r->cmd.xfer
directly, and instead always cap it to a fixed length. This was not done
for REQUEST SENSE, and this patch fixes it.
Reported-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Don't use req before it has been initialised in scsi_req_new().
This fixes a compile failure due to gcc complaining about this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Can be useful when debugging the device scan phase.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Unit attention conditions override any sense data the device already
has. Their signaling and clearing is handled entirely by the SCSIBus
code, and they are completely transparent to the SCSIDevices.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Also introduce the first occurrence of "independent" SCSIReqOps,
to handle invalid commands in common code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This will let SCSIBus detect requests sent to an invalid LUN, and
handle them itself. However, there will be still support for only one
LUN per target
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This struct is currently unnamed. Give it a name and use it
explicitly to decouple (some parts of) CDB parsing from
SCSIRequest.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Right now the CDB is not passed to the SCSIBus until scsi_req_enqueue.
Passing it to scsi_req_new will let scsi_req_new dispatch common requests
through different reqops.
Moving the memcpy to scsi_req_new is a hack that will go away as
soon as scsi_req_new will also take care of the parsing.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
