Usually guest devices don't like other writers to the same image, so
they use blk_set_perm() to prevent this from happening. In the migration
phase before the VM is actually running, though, they don't have a
problem with writes to the image. On the other hand, storage migration
needs to be able to write to the image in this phase, so the restrictive
blk_set_perm() call of qdev devices breaks it.
This patch flags all BlockBackends with a qdev device as
blk->disable_perm during incoming migration, which means that the
requested permissions are stored in the BlockBackend, but not actually
applied to its root node yet.
Once migration has finished and the VM should be resumed, the
permissions are applied. If they cannot be applied (e.g. because the NBD
server used for block migration hasn't been shut down), resuming the VM
fails.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Kashyap Chamarthy <kchamart@redhat.com>
This behavior is not indicated in the datasheet and can confuse the OS.
The TCO can trap NMIs from SERR# or IOCHK# and convert them to SMIs; but
any other TCO event is either delivered as an SMI or completely disabled.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SocketAddress is a simple union, and simple unions are awkward: they
have their variant members wrapped in a "data" object on the wire, and
require additional indirections in C. I intend to limit its use to
existing external interfaces. New ones should use SocketAddressFlat.
I further intend to convert all internal interfaces to
SocketAddressFlat. This helper should go away then.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1490895797-29094-8-git-send-email-armbru@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
MemoryRegionCache did not know about virtio support for IOMMUs (because the
two features were developed at the same time). Revert MemoryRegionCache
to "normal" address_space_* operations for 2.9, as it is simpler than
undoing the virtio patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We assumes the iommu_ops were attached to the root region of address
space. This may not be true for all kinds of IOMMU implementation and
especially after commit 3716d5902d ("pci: introduce a bus master
container"). So fix this by not assuming as->root has iommu_ops,
instead depending on the regions reported by memory listener through:
- register a memory listener to dma_as
- during region_add, if it's a region of IOMMU, register a specific
IOMMU notifier, and store all notifiers in a list.
- during region_del, compare and delete the IOMMU notifier from the list
This is also a must for making vhost device IOTLB works for all types
of IOMMUs. Note, since we register one notifier during each
.region_add, the IOTLB may be flushed more than one times, this is
suboptimal and could be optimized in the future.
Reported-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Fixes: 3716d5902d ("pci: introduce a bus master container")
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Maxime Coquelin <maxime.coquelin@redhat.com>
If, once the kernel has booted, we try to remove a memory
hotplugged while the kernel was not started, QEMU crashes on
an assert:
qemu-system-ppc64: hw/virtio/vhost.c:651:
vhost_commit: Assertion `r >= 0' failed.
...
#4 in vhost_commit
#5 in memory_region_transaction_commit
#6 in pc_dimm_memory_unplug
#7 in spapr_memory_unplug
#8 spapr_machine_device_unplug
#9 in hotplug_handler_unplug
#10 in spapr_lmb_release
#11 in detach
#12 in set_allocation_state
#13 in rtas_set_indicator
...
If we take a closer look to the guest kernel log, we can see when
we try to unplug the memory:
pseries-hotplug-mem: Attempting to hot-add 4 LMB(s)
What happens:
1- The kernel has ignored the memory hotplug event because
it was not started when it was generated.
2- When we hot-unplug the memory,
QEMU starts to remove the memory,
generates an hot-unplug event,
and signals the kernel of the incoming new event
3- as the kernel is started, on the QEMU signal, it reads
the event list, decodes the hotplug event and tries to
finish the hotplugging.
4- QEMU receive the the hotplug notification while it
is trying to hot-unplug the memory. This moves the memory
DRC to an invalid state
This patch prevents this by not allowing to set the allocation
state to USABLE while the DRC is awaiting release.
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1432382
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
long is 32-bits on 64-bit windows, which caused the top half of the
address to be truncated; this patch changes it to use the
QEMU_ALIGN_UP macro which does not suffer the same problem
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This reverts commit 07bfa35477.
The global variable is only read as part of a
apic_reset_irq_delivered();
qemu_irq_raise(s->irq);
if (!apic_get_irq_delivered()) {
sequence, so the value never matters at migration time.
Reported-by: Dr. David Alan Gilbert <dglibert@redhat.com>
Cc: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The multithreaded TCG implementation exposed deadlocks in the win32
condition variables: as implemented, qemu_cond_broadcast waited on
receivers, whereas the pthreads API it was intended to emulate does
not. This was causing a deadlock because broadcast was called while
holding the IO lock, as well as all possible waiters blocked on the
same lock.
This patch replaces all the custom synchronisation code for mutexes
and condition variables with native Windows primitives (SRWlocks and
condition variables) with the same semantics as their POSIX
equivalents. To enable that, it requires a Windows Vista or newer host
OS.
Signed-off-by: Andrey Shedel <ashedel@microsoft.com>
[AB: edited commit message]
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-Id: <20170324220141.10104-1-Andrew.Baumann@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
virtio_input_send buffers input events until it sees a SYNC. Then it
either sends or drops the entire batch, depending on whether eventq
has enough space available. The case to avoid here is partial sends
where only part of the batch would get to the guest.
Using virtqueue_get_avail_bytes to check the state of eventq was not
correct. The queue may have a smaller number of larger buffers
available so bytes may be enough but the batch would still not be
possible to send, leading to the "Huh? No vq elem available" error.
Instead of checking available bytes, this patch optimistically pops
buffers from the queue and puts them back in case it runs out of
space and the batch needs to be dropped.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Message-id: 1490365490-4854-3-git-send-email-lprosek@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
They will be used in virtio-scsi-dataplane.c as well, so move them to
header.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170317061447.16243-2-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Just a single bugfix in this batch. It's not strictly in ppc code,
though it's for the pseries machine's benefit. Eduardo suggested it
go through my tree however.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=jFKm
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170323' into staging
ppc patch queue for 2017-03-23
Just a single bugfix in this batch. It's not strictly in ppc code,
though it's for the pseries machine's benefit. Eduardo suggested it
go through my tree however.
# gpg: Signature made Thu 23 Mar 2017 10:09:17 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170323:
numa,spapr: align default numa node memory size to 256MB
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch creates inline wrapper functions in xen_common.h for all open
coded calls to xc_hvm_XXX() functions outside of xen_common.h so that use
of xen_xc can be made implicit. This again is in preparation for the move
to using libxendevicemodel.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
This patch is a purely cosmetic change that avoids a name collision in
a subsequent patch.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Doing this will make the transition to using the new libxendevicemodel
interface less intrusive on the callers of these functions, since using
the new library will require a change of handle.
NOTE: The patch also moves the 'externs' for xen_xc and xen_fmem from
xen_backend.h to xen_common.h, and the declarations from
xen_backend.c to xen-common.c, which is where they belong.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Allow block backends to forward drain requests to their devices/users.
The initial intended purpose for this patch is to allow BBs to forward
requests along to BlockJobs, which will want to pause if their associated
BB has entered a drained region.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 20170316212351.13797-3-jsnow@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
A system with multiple VMGENID devices is undefined in the VMGENID spec by
omission.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Ben Warren <ben@skyportsystems.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The WRITE_POINTER linker/loader command that underlies VMGENID depends on
commit baf2d5bfba ("fw-cfg: support writeable blobs", 2017-01-12), which
in turn depends on fw_cfg DMA.
DMA for fw_cfg is enabled in 2.5+ machine types only (see commit
e6915b5f3a, "fw_cfg: unbreak migration compatibility for 2.4 and earlier
machines", 2016-02-18).
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Ben Warren <ben@skyportsystems.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Ben Warren <ben@skyportsystems.com <mailto:ben@skyportsystems.com>>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Since commit 224245b ("spapr: Add LMB DR connectors"), NUMA node
memory size must be aligned to 256MB (SPAPR_MEMORY_BLOCK_SIZE).
But when "-numa" option is provided without "mem" parameter,
the memory is equally divided between nodes, but 8MB aligned.
This can be not valid for pseries.
In that case we can have:
$ ./ppc64-softmmu/qemu-system-ppc64 -m 4G -numa node -numa node -numa node
qemu-system-ppc64: Node 0 memory size 0x55000000 is not aligned to 256 MiB
With this patch, we have:
(qemu) info numa
3 nodes
node 0 cpus: 0
node 0 size: 1280 MB
node 1 cpus:
node 1 size: 1280 MB
node 2 cpus:
node 2 size: 1536 MB
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
qemu-ga's socket activation support was not obeying the LISTEN_PID
environment variable, which avoids that a process uses a socket-activation
file descriptor meant for its parent.
Mess can for example ensue if a process forks a children before consuming
the socket-activation file descriptor and therefore setting O_CLOEXEC
on it.
Luckily, qemu-nbd also got socket activation code, and its copy does
support LISTEN_PID. Some extra fixups are needed to ensure that the
code can be used for both, but that's what this patch does. The
main change is to replace get_listen_fds's "consume" argument with
the FIRST_SOCKET_ACTIVATION_FD macro from the qemu-nbd code.
Cc: "Richard W.M. Jones" <rjones@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
bdrv_child_set_perm alone is not very usable because the caller must
call bdrv_child_check_perm first. This is already encapsulated
conveniently in bdrv_child_try_set_perm, so remove the other prototypes
from the header and fix the one wrong caller, block/mirror.c.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
More fixes missed in the previous pull request.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYyfidAAoJECgfDbjSjVRp1yYIAKC52EwDVcJxL2CEGncCQTVT
i9x04TYmzLOO+dERsO7Z+jphoB1cxpVxZVrvG5wfZo07gcGheNk524ABM2c9tNqa
7OZFcdBmN/l5C9ynL6aCdgu/bns5sEMUXf3By3l8iWKupc1C8URWGrfMVypFDumZ
AOSD/4bbvXxZlZjOENq5LsRHYU68KBK07C1fDRJA7b7ChXHS6qefeq6fbOvI9zJ7
24MltJMsNS36l//namD2HFPnO1eD3HXc57yBn5QBTTn5FERIghxYSsluAY7irKMp
UurF1D0pUL1sU2fjaLwFRBJL15tz6syjYOkna9cGmOT8m1D7CYnKjCRErxtqAmE=
=4pMp
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pci: fixes
More fixes missed in the previous pull request.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 16 Mar 2017 02:29:49 GMT
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
virtio-serial-bus: Delete timer from list before free it
hw/virtio: fix Power Management Control Register for PCI Express virtio devices
hw/virtio: fix Link Control Register for PCI Express virtio devices
hw/virtio: fix error enabling flags in Device Control register
hw/pcie: fix Extended Configuration Space for devices with no Extended Capabilities
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a helper to say whether a RAMBlock was created as a
shared mapping.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Quoting cirrus source code:
Follow real hardware, cirrus card emulated has 4 MB video memory.
Also accept 8 MB/16 MB for backward compatibility.
So just use 4MB by default. We decided to leave that at 8MB by default
a while ago, for live migration compatibility reasons. But we have
compat properties to handle that, so that isn't a compeling reason.
This also removes some sanity check inconsistencies in the cirrus code.
Some places check against the allocated video memory, some places check
against the 4MB physical hardware has. Guest code can trigger asserts
because of that.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1489494514-15606-1-git-send-email-kraxel@redhat.com
There is a special code path (dpy_gfx_copy) to allow graphic emulation
notify user interface code about bitblit operations carryed out by
guests. It is supported by cirrus and vnc server. The intended purpose
is to optimize display scrolls and just send over the scroll op instead
of a full display update.
This is rarely used these days though because modern guests simply don't
use the cirrus blitter any more. Any linux guest using the cirrus drm
driver doesn't. Any windows guest newer than winxp doesn't ship with a
cirrus driver any more and thus uses the cirrus as simple framebuffer.
So this code tends to bitrot and bugs can go unnoticed for a long time.
See for example commit "3e10c3e vnc: fix qemu crash because of SIGSEGV"
which fixes a bug lingering in the code for almost a year, added by
commit "c7628bf vnc: only alloc server surface with clients connected".
Also the vnc server will throttle the frame rate in case it figures the
network can't keep up (send buffers are full). This doesn't work with
dpy_gfx_copy, for any copy operation sent to the vnc client we have to
send all outstanding updates beforehand, otherwise the vnc client might
run the client side blit on outdated data and thereby corrupt the
display. So this dpy_gfx_copy "optimization" might even make things
worse on slow network links.
Lets kill it once for all.
Oh, and one more reason: Turns out (after writing the patch) we have a
security bug in that code path ...
Fixes: CVE-2016-9603
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1489494419-14340-1-git-send-email-kraxel@redhat.com
In function cpu_physical_memory_sync_dirty_bitmap, file
include/exec/ram_addr.h:
if (src[idx][offset]) {
unsigned long bits = atomic_xchg(&src[idx][offset], 0);
unsigned long new_dirty;
new_dirty = ~dest[k];
dest[k] |= bits;
new_dirty &= bits;
num_dirty += ctpopl(new_dirty);
}
After these codes executed, only the pages not dirtied in bitmap(dest),
but dirtied in dirty_memory[DIRTY_MEMORY_MIGRATION] will be calculated.
For example:
When ram_list.dirty_memory[DIRTY_MEMORY_MIGRATION] = 0b00001111,
and atomic_rcu_read(&migration_bitmap_rcu)->bmap = 0b00000011,
the new_dirty will be 0b00001100, and this function will return 2 but not
4 which is expected.
the dirty pages in dirty_memory[DIRTY_MEMORY_MIGRATION] are all new,
so these should be calculated also.
Signed-off-by: Chao Fan <fanc.fnst@cn.fujitsu.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
As the pci ahci can be hotplug and unplug, in the ahci unrealize
function it should free all the resource once allocated in the
realized function. This patch add ide_exit to free the resource.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Message-id: 1488449293-80280-3-git-send-email-liqiang6-s@360.cn
Signed-off-by: John Snow <jsnow@redhat.com>
Make Power Management State flag writable to conform
with the PCI Express spec.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make several Link Control Register flags writable to conform
with the PCI Express spec.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When the virtio devices are PCI Express, make error-enabling flags
writable to respect the PCIe spec.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Absence of any Extended Capabilities is required to be
indicated by an Extended Capability header with a Capability ID of
0000h, a Capability Version of 0h, and a Next Capability Offset of 000h.
Instead of inserting a 'NULL' capability is simpler to mark the start
of the Extended Configuration Space as read-only to achieve the same
behaviour.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
96a8821d21 ("virtio: unbreak virtio-pci with IOMMU after caching ring
translations") tries to make IOMMU works with virtio memory region
cache, but it requires IOMMU to be created before any virtio
devices. This is sub optimal, fixing this by introduce a bus master
container to make sure address space can be initialized during device
registering, and then we can safely set alias and make
bus_master_enable_region as its subregion during bus master
initialization.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
icount has become much slower after tcg_cpu_exec has stopped
using the BQL. There is also a latent bug that is masked by
the slowness.
The slowness happens because every occurrence of a QEMU_CLOCK_VIRTUAL
timer now has to wake up the I/O thread and wait for it. The rendez-vous
is mediated by the BQL QemuMutex:
- handle_icount_deadline wakes up the I/O thread with BQL taken
- the I/O thread wakes up and waits on the BQL
- the VCPU thread releases the BQL a little later
- the I/O thread raises an interrupt, which calls qemu_cpu_kick
- the VCPU thread notices the interrupt, takes the BQL to
process it and waits on it
All this back and forth is extremely expensive, causing a 6 to 8-fold
slowdown when icount is turned on.
One may think that the issue is that the VCPU thread is too dependent
on the BQL, but then the latent bug comes in. I first tried removing
the BQL completely from the x86 cpu_exec, only to see everything break.
The only way to fix it (and make everything slow again) was to add a dummy
BQL lock/unlock pair.
This is because in -icount mode you really have to process the events
before the CPU restarts executing the next instruction. Therefore, this
series moves the processing of QEMU_CLOCK_VIRTUAL timers straight in
the vCPU thread when running in icount mode.
The required changes include:
- make the timer notification callback wake up TCG's single vCPU thread
when run from another thread. By using async_run_on_cpu, the callback
can override all_cpu_threads_idle() when the CPU is halted.
- move handle_icount_deadline after qemu_tcg_wait_io_event, so that
the timer notification callback is invoked after the dummy work item
wakes up the vCPU thread
- make handle_icount_deadline run the timers instead of just waking the
I/O thread.
- stop processing the timers in the main loop
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no change for now, because the callback just invokes
qemu_notify_event.
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This dependency is the wrong way, and we will need util/qemu-timer.h from
sysemu/cpus.h in the next patch.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Using "-mem-prealloc" option for a large guest leads to higher guest
start-up and migration time. This is because with "-mem-prealloc" option
qemu tries to map every guest page (create address translations), and
make sure the pages are available during runtime. virsh/libvirt by
default, seems to use "-mem-prealloc" option in case the guest is
configured to use huge pages. The patch tries to map all guest pages
simultaneously by spawning multiple threads. Currently limiting the
change to QEMU library functions on POSIX compliant host only, as we are
not sure if the problem exists on win32. Below are some stats with
"-mem-prealloc" option for guest configured to use huge pages.
------------------------------------------------------------------------
Idle Guest | Start-up time | Migration time
------------------------------------------------------------------------
Guest stats with 2M HugePage usage - single threaded (existing code)
------------------------------------------------------------------------
64 Core - 4TB | 54m11.796s | 75m43.843s
64 Core - 1TB | 8m56.576s | 14m29.049s
64 Core - 256GB | 2m11.245s | 3m26.598s
------------------------------------------------------------------------
Guest stats with 2M HugePage usage - map guest pages using 8 threads
------------------------------------------------------------------------
64 Core - 4TB | 5m1.027s | 34m10.565s
64 Core - 1TB | 1m10.366s | 8m28.188s
64 Core - 256GB | 0m19.040s | 2m10.148s
-----------------------------------------------------------------------
Guest stats with 2M HugePage usage - map guest pages using 16 threads
-----------------------------------------------------------------------
64 Core - 4TB | 1m58.970s | 31m43.400s
64 Core - 1TB | 0m39.885s | 7m55.289s
64 Core - 256GB | 0m11.960s | 2m0.135s
-----------------------------------------------------------------------
Changed in v2:
- modify number of memset threads spawned to min(smp_cpus, 16).
- removed 64GB memory restriction for spawning memset threads.
Changed in v3:
- limit number of threads spawned based on
min(sysconf(_SC_NPROCESSORS_ONLN), 16, smp_cpus)
- implement memset thread specific siglongjmp in SIGBUS signal_handler.
Changed in v4
- remove sigsetjmp/siglongjmp and SIGBUS unblock/block for main thread
as main thread no longer touches any pages.
- simplify code my returning memset_thread_failed status from
touch_all_pages.
Signed-off-by: Jitendra Kolhe <jitendra.kolhe@hpe.com>
Message-Id: <1487907103-32350-1-git-send-email-jitendra.kolhe@hpe.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 'name' parameter to memory_region_init_* had been marked as debug
only, however vmstate_region_ram uses it as a parameter to
qemu_ram_set_idstr to set RAMBlock names and these form part of the
migration stream.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170309152708.30635-1-dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This set has a handful og bugfixes to go into qemu-2.9. This includes
an update to the dtc/libfdt submodule which will fix the build errors
seen on some distributions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=dxrH
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170314' into staging
ppc patch queue for 2017-03-14
This set has a handful og bugfixes to go into qemu-2.9. This includes
an update to the dtc/libfdt submodule which will fix the build errors
seen on some distributions.
# gpg: Signature made Tue 14 Mar 2017 04:00:41 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170314:
dtc: Update submodule to avoid build errors
pseries: Don't expose PCIe extended config space on older machine types
target/ppc: fix cpu_ov setting for 32-bit
target/ppc: Fix wrong number of UAMR register
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The definition of the major() and minor() macros are moving within glibc to
<sys/sysmacros.h>. Include this header when it is available to avoid the
following sorts of build-stopping messages:
qga/commands-posix.c: In function ‘dev_major_minor’:
qga/commands-posix.c:656:13: error: In the GNU C Library, "major" is defined
by <sys/sysmacros.h>. For historical compatibility, it is
currently defined by <sys/types.h> as well, but we plan to
remove this soon. To use "major", include <sys/sysmacros.h>
directly. If you did not intend to use a system-defined macro
"major", you should undefine it after including <sys/types.h>. [-Werror]
*devmajor = major(st.st_rdev);
^~~~~~~~~~~~~~~~~~~~~~~~~~
qga/commands-posix.c:657:13: error: In the GNU C Library, "minor" is defined
by <sys/sysmacros.h>. For historical compatibility, it is
currently defined by <sys/types.h> as well, but we plan to
remove this soon. To use "minor", include <sys/sysmacros.h>
directly. If you did not intend to use a system-defined macro
"minor", you should undefine it after including <sys/types.h>. [-Werror]
*devminor = minor(st.st_rdev);
^~~~~~~~~~~~~~~~~~~~~~~~~~
The additional include allows the build to complete on Fedora 26 (Rawhide)
with glibc version 2.24.90.
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
bb9986452 "spapr_pci: Advertise access to PCIe extended config space"
allowed guests to access the extended config space of PCI Express devices
via the PAPR interfaces, even though the paravirtualized bus mostly acts
like plain PCI.
However, that patch enabled access unconditionally, including for existing
machine types, which is an unwise change in behaviour. This patch limits
the change to pseries-2.9 (and later) machine types.
Suggested-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
glibc blacklists TSX on Haswell CPUs with model==60 and
stepping < 4. To make the Haswell CPU model more useful, make
those guests actually use TSX by changing CPU stepping to 4.
References:
* glibc commit 2702856bf45c82cf8e69f2064f5aa15c0ceb6359
https://sourceware.org/git/?p=glibc.git;a=commit;h=2702856bf45c82cf8e69f2064f5aa15c0ceb6359
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170309181212.18864-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488317230-26248-19-git-send-email-armbru@redhat.com>
The next few commits will put the errors to use where appropriate.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488317230-26248-13-git-send-email-armbru@redhat.com>
The next few commits will put the errors to use where appropriate.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <1488317230-26248-9-git-send-email-armbru@redhat.com>
Currently the QObjectInputVisitor assumes that all scalar values are
directly represented as the final types declared by the thing being
visited. i.e. it assumes an 'int' is using QInt, and a 'bool' is using
QBool, etc. This is good when QObjectInputVisitor is fed a QObject
that came from a JSON document on the QMP monitor, as it will strictly
validate correctness.
To allow QObjectInputVisitor to be reused for visiting a QObject
originating from keyval_parse(), an alternative mode is needed where
all the scalars types are represented as QString and converted on the
fly to the final desired type.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1475246744-29302-8-git-send-email-berrange@redhat.com>
Rebased, conflicts resolved, commit message updated to refer to
keyval_parse(). autocast replaced by keyval in identifiers,
noautocast replaced by fail in tests.
Fix qobject_input_type_uint64_keyval() not to reject '-', for QemuOpts
compatibility: replace parse_uint_full() by open-coded
parse_option_number(). The next commit will add suitable tests.
Leave out the fancy ERANGE error reporting for now, but add a TODO
comment. Add it qobject_input_type_int64_keyval() and
qobject_input_type_number_keyval(), too.
Open code parse_option_bool() and parse_option_size() so we have to
call qobject_input_get_name() only when actually needed. Again, leave
out ERANGE error reporting for now.
QAPI/QMP downstream extension prefixes __RFQDN_ don't work, because
keyval_parse() splits them at '.'. This will be addressed later in
the series.
qobject_input_type_int64_keyval(), qobject_input_type_uint64_keyval(),
qobject_input_type_number_keyval() tweaked for style.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <1488317230-26248-5-git-send-email-armbru@redhat.com>
keyval_parse() parses KEY=VALUE,... into a QDict. Works like
qemu_opts_parse(), except:
* Returns a QDict instead of a QemuOpts (d'oh).
* Supports nesting, unlike QemuOpts: a KEY is split into key
fragments at '.' (dotted key convention; the block layer does
something similar on top of QemuOpts). The key fragments are QDict
keys, and the last one's value is updated to VALUE.
* Each key fragment may be up to 127 bytes long. qemu_opts_parse()
limits the entire key to 127 bytes.
* Overlong key fragments are rejected. qemu_opts_parse() silently
truncates them.
* Empty key fragments are rejected. qemu_opts_parse() happily
accepts empty keys.
* It does not store the returned value. qemu_opts_parse() stores it
in the QemuOptsList.
* It does not treat parameter "id" specially. qemu_opts_parse()
ignores all but the first "id", and fails when its value isn't
id_wellformed(), or duplicate (a QemuOpts with the same ID is
already stored). It also screws up when a value contains ",id=".
* Implied value is not supported. qemu_opts_parse() desugars "foo" to
"foo=on", and "nofoo" to "foo=off".
* An implied key's value can't be empty, and can't contain ','.
I intend to grow this into a saner replacement for QemuOpts. It'll
take time, though.
Note: keyval_parse() provides no way to do lists, and its key syntax
is incompatible with the __RFQDN_ prefix convention for downstream
extensions, because it blindly splits at '.', even in __RFQDN_. Both
issues will be addressed later in the series.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1488317230-26248-4-git-send-email-armbru@redhat.com>
When adding an Error parameter, bdrv_replace_in_backing_chain() would
become nothing more than a wrapper around change_parent_backing_link().
So make the latter public, renamed as bdrv_replace_node(), and remove
bdrv_replace_in_backing_chain().
Most of the callers just remove a node from the graph that they just
inserted, so they can use &error_abort, but completion of a mirror job
with 'replaces' set can actually fail.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
change_parent_backing_link() will need to update multiple BdrvChild
objects at once. Checking permissions reference by reference doesn't
work because permissions need to be consistent only with all parents
moved to the new child.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJYvOJVAAoJEO8Ells5jWIRQwEH/32qzm0gLSZnxmrmvn3iizA1
t5lYfy0mpf2kdP4U58OqcgBYoGZmL0i316ZyIn2i9k9i2NXX/1LHp3to31p/msg3
0dFwdajfSkMCZROrbU9XJZRoCSD4+DeDKa/NBA+jbQSZgscRoBjM4bjYB/U72Swp
edRp/ZwD5BTO5Hpm3NDqBxmLNGqFxaeNamgx7eCrZ7OBAHFqmkNhdYH7WVKA31tU
KH1KaB24POKAr6hItR4Qcs2ZDA1zPBPblKVpmZ9AisQChg/lFphMQjqyJunRRuOk
OKV7fMWvfVrhqVR+IR9+J8EDS9lMI/2VA3hhs/umcmsao7uqixX57G8NmDLR6Tw=
=0Lht
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 06 Mar 2017 04:15:17 GMT
# gpg: using RSA key 0xEF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
net/filter-mirror: Follow CODING_STYLE
COLO-compare: Fix icmp and udp compare different packet always dump bug
COLO-compare: Optimize compare_common and compare_tcp
COLO-compare: Rename compare function and remove duplicate codes
filter-rewriter: skip net_checksum_calculate() while offset = 0
net/colo: fix memory double free error
vmxnet3: VMStatify rx/tx q_descr and int_state
vmxnet3: Convert ring values to uint32_t's
net/colo-compare: Fix memory free error
colo-compare: Fix removing fds been watched incorrectly in finalization
char: remove the right fd been watched in qemu_chr_fe_set_handlers()
colo-compare: kick compare thread to exit after some cleanup in finalization
colo-compare: use g_timeout_source_new() to process the stale packets
NetRxPkt: Remove code duplication in net_rx_pkt_pull_data()
NetRxPkt: Account buffer with ETH header in IOV length
NetRxPkt: Do not try to pull more data than present
NetRxPkt: Fix memory corruption on VLAN header stripping
eth: Extend vlan stripping functions
net: Remove useless local var pkt
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make VLAN stripping functions return number of bytes
copied to given Ethernet header buffer.
This information should be used to re-compose
packet IOV after VLAN stripping.
Cc: qemu-stable@nongnu.org
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-29-git-send-email-armbru@redhat.com>
Fix the design flaw demonstrated in the previous commit: new method
check_list() lets input visitors report that unvisited input remains
for a list, exactly like check_struct() lets them report that
unvisited input remains for a struct or union.
Implement the method for the qobject input visitor (straightforward),
and the string input visitor (less so, due to the magic list syntax
there). The opts visitor's list magic is even more impenetrable, and
all I can do there today is a stub with a FIXME comment. No worse
than before.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1488544368-30622-26-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The split between tests/test-qobject-input-visitor.c and
tests/test-qobject-input-strict.c now makes less sense than ever. The
next commit will take care of that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-20-git-send-email-armbru@redhat.com>
visit_optional() is to be called only between visit_start_struct() and
visit_end_struct(). Visitors that don't support struct visits,
i.e. don't implement start_struct(), end_struct(), have no use for it.
Clarify documentation.
The string input visitor doesn't support struct visits. Its
parse_optional() is therefore useless. Drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-16-git-send-email-armbru@redhat.com>
Error messages refer to nodes of the QObject being visited by name.
Trouble is the names are sometimes less than helpful:
* The name of the root QObject is whatever @name argument got passed
to the visitor, except NULL gets mapped to "null". We commonly pass
NULL. Not good.
Avoiding errors "at the root" mitigates. For instance,
visit_start_struct() can only fail when the visited object is not a
dictionary, and we commonly ensure it is beforehand.
* The name of a QDict's member is the member key. Good enough only
when this happens to be unique.
* The name of a QList's member is "null". Not good.
Improve error messages by referring to nodes by path instead, as
follows:
* The path of the root QObject is whatever @name argument got passed
to the visitor, except NULL gets mapped to "<anonymous>".
* The path of a root QDict's member is the member key.
* The path of a root QList's member is "[%u]", where %u is the list
index, starting at zero.
* The path of a non-root QDict's member is the path of the QDict
concatenated with "." and the member key.
* The path of a non-root QList's member is the path of the QList
concatenated with "[%u]", where %u is the list index.
For example, the incorrect QMP command
{ "execute": "blockdev-add", "arguments": { "node-name": "foo", "driver": "raw", "file": {"driver": "file" } } }
now fails with
{"error": {"class": "GenericError", "desc": "Parameter 'file.filename' is missing"}}
instead of
{"error": {"class": "GenericError", "desc": "Parameter 'filename' is missing"}}
and
{ "execute": "input-send-event", "arguments": { "device": "bar", "events": [ [] ] } }
now fails with
{"error": {"class": "GenericError", "desc": "Invalid parameter type for 'events[0]', expected: object"}}
instead of
{"error": {"class": "GenericError", "desc": "Invalid parameter type for 'null', expected: QDict"}}
Aside: calling the thing "parameter" is suboptimal for QMP, because
the root object is "arguments" there.
The qobject output visitor doesn't have this problem because it should
not fail. Same for dealloc and clone visitors.
The string visitors don't have this problem because they visit just
one value, whose name needs to be passed to the visitor as @name. The
string output visitor shouldn't fail anyway.
The options visitor uses QemuOpts names. Their name space is flat, so
the use of QDict member keys as names is fine. NULL names used with
roots and lists could conceivably result in bad error messages. Left
for another day.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-15-git-send-email-armbru@redhat.com>
The QERR_ macros are leftovers from the days of "rich" error objects.
QERR_QMP_BAD_INPUT_OBJECT, QERR_QMP_BAD_INPUT_OBJECT_MEMBER,
QERR_QMP_EXTRA_MEMBER are used in just one place now, except for one
use that has crept into qobject-input-visitor.c.
Drop these macros, to make the (bad) error messages more visible.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-10-git-send-email-armbru@redhat.com>
The command registry encapsulates a single command list. Give the
functions using it a parameter instead. Define suitable command lists
in monitor, guest agent and test-qmp-commands.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1488544368-30622-6-git-send-email-armbru@redhat.com>
[Debugging turds buried]
Reviewed-by: Eric Blake <eblake@redhat.com>
The way we get QMP commands registered is high tech:
* qapi-commands.py generates qmp_init_marshal() that does the actual work
* it also generates the magic to register it as a MODULE_INIT_QAPI
function, so it runs when someone calls
module_call_init(MODULE_INIT_QAPI)
* main() calls module_call_init()
QEMU needs to register a few non-qapified commands. Same high tech
works: monitor.c has its own qmp_init_marshal() along with the magic
to make it run in module_call_init(MODULE_INIT_QAPI).
QEMU also needs to unregister commands that are not wanted in this
build's configuration (commit 5032a16). Simple enough:
qmp_unregister_commands_hack(). The difficulty is to make it run
after the generated qmp_init_marshal(). We can't simply run it in
monitor.c's qmp_init_marshal(), because the order in which the
registered functions run is indeterminate. So qmp_init_marshal()
registers qmp_unregister_commands_hack() separately. Since
registering *appends* to the list of registered functions, this will
make it run after all the functions that have been registered already.
I suspect it takes a long and expensive computer science education to
not find this silly.
Dumb it down as follows:
* Drop MODULE_INIT_QAPI entirely
* Give the generated qmp_init_marshal() external linkage.
* Call it instead of module_call_init(MODULE_INIT_QAPI)
* Except in QEMU proper, call new monitor_init_qmp_commands() that in
turn calls the generated qmp_init_marshal(), registers the
additional commands and unregisters the unwanted ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1488544368-30622-5-git-send-email-armbru@redhat.com>
This will probably be my last pull request before the hard freeze. It
has some new work, but that has all been posted in draft before the
soft freeze, so I think it's reasonable to include in qemu-2.9.
This batch has:
* A substantial amount of POWER9 work
* Implements the legacy (hash) MMU for POWER9
* Some more preliminaries for implementing the POWER9 radix
MMU
* POWER9 has_work
* Basic POWER9 compatibility mode handling
* Removal of some premature tests
* Some cleanups and fixes to the existing MMU code to make the
POWER9 work simpler
* A bugfix for TCG multiply adds on power
* Allow pseries guests to access PCIe extended config space
This also includes a code-motion not strictly in ppc code - moving
getrampagesize() from ppc code to exec.c. This will make some future
VFIO improvements easier, Paolo said it was ok to merge via my tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PcNw
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170303' into staging
ppc patch queuye for 2017-03-03
This will probably be my last pull request before the hard freeze. It
has some new work, but that has all been posted in draft before the
soft freeze, so I think it's reasonable to include in qemu-2.9.
This batch has:
* A substantial amount of POWER9 work
* Implements the legacy (hash) MMU for POWER9
* Some more preliminaries for implementing the POWER9 radix
MMU
* POWER9 has_work
* Basic POWER9 compatibility mode handling
* Removal of some premature tests
* Some cleanups and fixes to the existing MMU code to make the
POWER9 work simpler
* A bugfix for TCG multiply adds on power
* Allow pseries guests to access PCIe extended config space
This also includes a code-motion not strictly in ppc code - moving
getrampagesize() from ppc code to exec.c. This will make some future
VFIO improvements easier, Paolo said it was ok to merge via my tree.
# gpg: Signature made Fri 03 Mar 2017 03:20:36 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170303:
target/ppc: rewrite f[n]m[add,sub] using float64_muladd
spapr: Small cleanup of PPC MMU enums
spapr_pci: Advertise access to PCIe extended config space
target/ppc: Rework hash mmu page fault code and add defines for clarity
target/ppc: Move no-execute and guarded page checking into new function
target/ppc: Add execute permission checking to access authority check
target/ppc: Add Instruction Authority Mask Register Check
hw/ppc/spapr: Add POWER9 to pseries cpu models
target/ppc/POWER9: Add cpu_has_work function for POWER9
target/ppc/POWER9: Add POWER9 pa-features definition
target/ppc/POWER9: Add POWER9 mmu fault handler
target/ppc: Don't gen an SDR1 on POWER9 and rework register creation
target/ppc: Add patb_entry to sPAPRMachineState
target/ppc/POWER9: Add POWERPC_MMU_V3 bit
powernv: Don't test POWER9 CPU yet
exec, kvm, target-ppc: Move getrampagesize() to common code
target/ppc: Add POWER9/ISAv3.00 to compat_table
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These cause compilation failures on CentOS 6 or other operating
systems with older GCCs.
Cc: David Gibson <dgibson@redhat.com>
Cc: qemu-ppc@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1488558530-21016-3-git-send-email-pbonzini@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Migration from a 2.3.0 qemu results in a reboot on the receiving QEMU
due to a disagreement about SM (System management) interrupts.
2.3.0 didn't have much SMI support, but it did set CPU_INTERRUPT_SMI
and this gets into the migration stream, but on 2.3.0 it
never got delivered.
~2.4.0 SMI interrupt support was added but was broken - so
that when a 2.3.0 stream was received it cleared the CPU_INTERRUPT_SMI
but never actually caused an interrupt.
The SMI delivery was recently fixed by 68c6efe07a, but the
effect now is that an incoming 2.3.0 stream takes the interrupt it
had flagged but it's bios can't actually handle it(I think
partly due to the original interrupt not being taken during boot?).
The consequence is a triple(?) fault and a reboot.
Tested from:
2.3.1 -M 2.3.0
2.7.0 -M 2.3.0
2.8.0 -M 2.3.0
2.8.0 -M 2.8.0
This corresponds to RH bugzilla entry 1420679.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170223133441.16010-1-dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
At the moment ram device's memory regions are DEVICE_NATIVE_ENDIAN. It's
incorrect. This memory region is backed by a MMIO area in host, so the
uint64_t data that MemoryRegionOps read from/write to this area should be
host-endian rather than target-endian. Hence, current code does not work
when target and host endianness are different which is the most common case
on PPC64. To fix it, this introduces DEVICE_HOST_ENDIAN for the ram device.
This has been tested on PPC64 BE/LE host/guest in all possible combinations
including TCG.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yongji Xie <xyjxie@linux.vnet.ibm.com>
Message-Id: <1488171164-28319-1-git-send-email-xyjxie@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Call kvm_on_sigbus_vcpu asynchronously from the VCPU thread.
Information for the SIGBUS can be stored in thread-local variables
and processed later in kvm_cpu_exec.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Build it on kvm_arch_on_sigbus_vcpu instead. They do the same
for "action optional" SIGBUSes, and the main thread should never get
"action required" SIGBUSes because it blocks the signal.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the KVM "eat signals" code under CONFIG_LINUX, in preparation
for moving it to kvm-all.c; reraise non-MCE SIGBUS immediately,
without passing it to KVM.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The cast is there because sigbus_handler is invoked via sigfd_handler.
But it feels just wrong to use struct qemu_signalfd_siginfo in the
prototype of a function that is passed to sigaction.
Instead, do a simple-minded conversion of qemu_signalfd_siginfo to
siginfo_t.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Merge the original development branch due to breakage caused by the
MTTCG merge.
Conflicts:
cpu-exec.c
translate-common.c
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
virtio support for region caches broke a bunch of stuff - fixing most of
it though it's not ideal. Still pondering the right way to fix it.
New: VM gen ID and hotplug for PXB.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYt7llAAoJECgfDbjSjVRp+r4H/1cmQ4F67H8oSOAT8xuAQFku
OdHoVRJMWf7CRvZ7JqVke/a877d+h6ZpfW5dZQ7hp7O7rkPiuPHa5PVb0WGwDqrD
scSOIvDPxJm19pnfZoF4zx+Ov45W5ahF+gwwm/sJU232ApLqOmAjs0FUxidkadQE
f5Jrjs20WO2Vkkcd3U7Zl31myre0V7AbwIm7dB/8B+dpL6bJcxSvlM4krwLdBY6S
lLs9V6ypRzjUxS3MDANL75KNrO/zys55J+Pa4sEh4+H0OX71v9Icl3s1zaM8J/EN
VPjdqhDvJuEahc50FbJyRZQGIzOZ6PcGMsKUHKlxoVmDYZ6Pv5lOnpaLZRT6HMk=
=ITdO
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pc: fixes, features
virtio support for region caches broke a bunch of stuff - fixing most of
it though it's not ideal. Still pondering the right way to fix it.
New: VM gen ID and hotplug for PXB.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 02 Mar 2017 06:19:17 GMT
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
hw/pxb-pcie: fix PCI Express hotplug support
tests/acpi: update DSDT after last patch
acpi: simplify _OSC
virtio: unbreak virtio-pci with IOMMU after caching ring translations
virtio: add missing region cache init in virtio_load()
virtio: invalidate memory in vring_set_avail_event()
virtio: guard vring access when setting notification
virtio: check for vring setup in virtio_queue_empty
MAINTAINERS: Add VM Generation ID entries
tests: Move reusable ACPI code into a utility file
qmp/hmp: add query-vm-generation-id and 'info vm-generation-id' commands
ACPI: Add Virtual Machine Generation ID support
ACPI: Add vmgenid blob storage to the build tables
docs: VM Generation ID device description
linker-loader: Add new 'write pointer' command
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ISA v3.00 adds the idea of a partition table which is used to store the
address translation details for all partitions on the system. The partition
table consists of double word entries indexed by partition id where the second
double word contains the location of the process table in guest memory. The
process table is registered by the guest via a h-call.
We need somewhere to store the address of the process table so we add an entry
to the sPAPRMachineState struct called patb_entry to represent the second
doubleword of a single partition table entry corresponding to the current
guest. We need to store this value so we know if the guest is using radix or
hash translation and the location of the corresponding process table in guest
memory. Since we only have a single guest per qemu instance, we only need one
entry.
Since the partition table is technically a hypervisor resource we require that
access to it is abstracted by the virtual hypervisor through the get_patbe()
call. Currently the value of the entry is never set (and thus
defaults to 0 indicating hash), but it will be required to both implement
POWER9 kvm support and tcg radix support.
We also add this field to be migrated as part of the sPAPRMachineState as we
will need it on the receiving side as the guest will never tell us this
information again and we need it to perform translation.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
getrampagesize() returns the largest supported page size and mainly
used to know if huge pages are enabled.
However is implemented in target-ppc/kvm.c and not available
in TCG or other architectures.
This renames and moves gethugepagesize() to mmap-alloc.c where
fd-based analog of it is already implemented. This renames and moves
getrampagesize() to exec.c as it seems to be the common place for
helpers like this.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Note: The 'postcopy: Update userfaultfd.h header' is part of
Paolo's header update and will disappear if applied after it.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJYtW9KAAoJEAUWMx68W/3nF/MQAIaMjoCkeVnCZsGCJ2VbJZcZ
Fb5gMNjnHUKwOeDhGuSBP7FGRMalYM2JNRufSiBZnUowCQMXi3Emjad6pGUiPTr0
B+L1czjw0FDdskQpE1U/StdruLiYBJ98oktnjlla00f+E9rylY0cMmrHpmqfRwDn
IXTa4qm77aw47Y2MYku1nce27gjA3JEko6Lg2fB7gTtwYzTi/uRrKa+ilbnTPoEZ
/ZzK8hcUYiV8oDAOtEmKSG3Azo+6ylzDG4r/ldwEecJPhZxeUk39AhDOoU0mx98N
OE8oOk2t/0Bo+mS7iOw9gZ8sr9p5L2myQkmoxxLuAXAcD9sHVlcp0eKi5lLYNmUa
oWnnYo3QeCvqrcZzhvSX0b4rLXoY4GP+qKpQo21eKIPEyq3v6EDhrk10UCTXaiBO
zxHblLgXSrX6VqYcEJGj2oUR/RjH9ouw3hjI5cDy/d/hRmNLCl8lwvPmVmv3tRer
6X1gcZSUs6hY/drs2/v6maJ0CqK/bx6/OBfkiUJUEN4Dg1ldgO2r1v8pBLukvM6c
De2aNRezl821HK487EvRlluUq0nO6L3LkqDTBql4/4Rf4HoTRXxoJ68sB0LBqym5
PwD/C3mQuvlWg8tKJtaHVtS0ESuSCSroaSk1FB648mSs8nJYYFjstc/XovuePqTl
6UT2OQbUdWITILoWSlI5
=PCYv
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20170228a' into staging
Migration pull
Note: The 'postcopy: Update userfaultfd.h header' is part of
Paolo's header update and will disappear if applied after it.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
# gpg: Signature made Tue 28 Feb 2017 12:38:34 GMT
# gpg: using RSA key 0x0516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20170228a: (27 commits)
postcopy: Add extra check for COPY function
postcopy: Add doc about hugepages and postcopy
postcopy: Check for userfault+hugepage feature
postcopy: Update userfaultfd.h header
postcopy: Allow hugepages
postcopy: Send whole huge pages
postcopy: Mask fault addresses to huge page boundary
postcopy: Load huge pages in one go
postcopy: Use temporary for placing zero huge pages
postcopy: Plumb pagesize down into place helpers
postcopy: Record largest page size
postcopy: enhance ram_block_discard_range for hugepages
exec: ram_block_discard_range
postcopy: Chunk discards for hugepages
postcopy: Transmit and compare individual page sizes
postcopy: Transmit ram size summary word
migration: fix use-after-free of to_dst_file
migration: Update docs to discourage version bumps
migration: fix id leak regression
migrate: Introduce a 'dc->vmsd' check to avoid segfault for --only-migratable
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I was hoping to get this pull request squeezed in before the soft
freeze, but I ran into some difficulties during testing. Everything
here was at least posted before the soft freeze, so I'm hoping we can
still merge it for 2.9.
The biggest things here are:
* Cleanups to handling of hashed page tables, that will make
adding support for the POWER9 MMU easier
* Cleanups to the XICS interrupt controller that will make
implementing the powernv machine easier
* TCG implementation of extended overflow and carry handling for
POWER9
It also includes:
* Increasing the CPU limit for pseries to 1024 vCPUs
* Generating proper OF node names in qemu (making hotplug and
coldplug logic closer together)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=gI0E
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170301' into staging
ppc patch queue for 2017-03-01
I was hoping to get this pull request squeezed in before the soft
freeze, but I ran into some difficulties during testing. Everything
here was at least posted before the soft freeze, so I'm hoping we can
still merge it for 2.9.
The biggest things here are:
* Cleanups to handling of hashed page tables, that will make
adding support for the POWER9 MMU easier
* Cleanups to the XICS interrupt controller that will make
implementing the powernv machine easier
* TCG implementation of extended overflow and carry handling for
POWER9
It also includes:
* Increasing the CPU limit for pseries to 1024 vCPUs
* Generating proper OF node names in qemu (making hotplug and
coldplug logic closer together)
# gpg: Signature made Wed 01 Mar 2017 04:43:06 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170301: (50 commits)
Add PowerPC 32-bit guest memory dump support
ppc/xics: rename 'ICPState *' variables to 'icp'
ppc/xics: move InterruptStatsProvider to the sPAPR machine
ppc/xics: move ics-simple post_load under the machine
ppc/xics: remove the XICSState classes
ppc/xics: export the XICS init routines
ppc/xics: move the ICP array under the sPAPR machine
ppc/xics: register the reset handler of ICP objects
ppc/xics: simplify spapr_dt_xics() interface
ppc/xics: use the QOM interface to grab an ICP
ppc/xics: move the cpu_setup() handler under the ICPState class
ppc/xics: simplify the cpu_setup() handler
ppc/xics: move kernel_xics_fd out of KVMXICSState
ppc/xics: extend the QOM interface to handle ICPs
ppc/xics: remove the XICS list of ICS
ppc/xics: register the reset handler of ICS objects
ppc/xics: remove xics_find_source()
ppc/xics: use the QOM interface to resend irqs
ppc/xics: use the QOM interface to get irqs
ppc/xics: use the QOM interface under the sPAPR machine
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements the VM Generation ID feature by passing a 128-bit
GUID to the guest via a fw_cfg blob.
Any time the GUID changes, an ACPI notify event is sent to the guest
The user interface is a simple device with one parameter:
- guid (string, must be "auto" or in UUID format
xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx)
Signed-off-by: Ben Warren <ben@skyportsystems.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows them to be centrally initialized and destroyed
The "AcpiBuildTables.vmgenid" array will be used to construct the
"etc/vmgenid_guid" fw_cfg blob.
Its contents will be linked into fw_cfg after being built on the
pc_machine_done() -> acpi_setup() -> acpi_build() call path, and dropped
without use on the subsequent, guest triggered, acpi_build_update() ->
acpi_build() call path.
Signed-off-by: Ben Warren <ben@skyportsystems.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is similar to the existing 'add pointer' functionality, but instead
of instructing the guest (BIOS or UEFI) to patch memory, it instructs
the guest to write the pointer back to QEMU via a writeable fw_cfg file.
Signed-off-by: Ben Warren <ben@skyportsystems.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=g3ew
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches
# gpg: Signature made Tue 28 Feb 2017 20:35:32 GMT
# gpg: using RSA key 0x7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (46 commits)
block: Add Error parameter to bdrv_append()
block: Add Error parameter to bdrv_set_backing_hd()
block: Assertions for resize permission
block: Assertions for write permissions
block: Pass BdrvChild to bdrv_aligned_preadv/pwritev and copy-on-read
tests: Remove FIXME comments
nbd/server: Use real permissions for NBD exports
migration/block: Use real permissions
hmp: Request permissions in qemu-io
commit: Add filter-node-name to block-commit
mirror: Add filter-node-name to blockdev-mirror
stream: Use real permissions in streaming block job
mirror: Use real permissions in mirror/active commit block job
blockjob: Factor out block_job_remove_all_bdrv()
block: Allow backing file links in change_parent_backing_link()
block: BdrvChildRole.attach/detach() callbacks
block: Fix pending requests check in bdrv_append()
backup: Use real permissions in backup block job
commit: Use real permissions for HMP 'commit'
commit: Use real permissions in commit block job
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* raspi2: add gpio controller and sdhost controller, with
the wiring so the guest can switch which controller the
SD card is attached to
(this is sufficient to get raspbian kernels to boot)
* GICv3: support state save/restore from KVM
* update Linux headers to 4.11
* refactor and QOMify the ARMv7M container object
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IC84
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20170228-1' into staging
target-arm queue:
* raspi2: add gpio controller and sdhost controller, with
the wiring so the guest can switch which controller the
SD card is attached to
(this is sufficient to get raspbian kernels to boot)
* GICv3: support state save/restore from KVM
* update Linux headers to 4.11
* refactor and QOMify the ARMv7M container object
# gpg: Signature made Tue 28 Feb 2017 17:11:49 GMT
# gpg: using RSA key 0x3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20170228-1: (21 commits)
bcm2835: add sdhost and gpio controllers
bcm2835_gpio: add bcm2835 gpio controller
hw/sd: add card-reparenting function
qdev: Have qdev_set_parent_bus() handle devices already on a bus
hw/intc/arm_gicv3_kvm: Reset GICv3 cpu interface registers
target-arm: Add GICv3CPUState in CPUARMState struct
hw/intc/arm_gicv3_kvm: Implement get/put functions
hw/intc/arm_gicv3_kvm: Add ICC_SRE_EL1 register to vmstate
update Linux headers to 4.11
update-linux-headers: update for 4.11
stm32f205: Rename 'nvic' local to 'armv7m'
stm32f205: Create armv7m object without using armv7m_init()
armv7m: Split systick out from NVIC
armv7m: Don't put core v7M devices under CONFIG_STELLARIS
armv7m: Make bitband device take the address space to access
armv7m: Make NVIC expose a memory region rather than mapping itself
armv7m: Make ARMv7M object take memory region link
armv7m: Use QOMified armv7m object in armv7m_init()
armv7m: QOMify the armv7m container
armv7m: Move NVICState struct definition into header
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds recording and replaying audio data. Is saves synchronization
information for audio out and inputs from the microphone.
v2: removed unneeded whitespace change
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-id: 20170202055054.4848.94901.stgit@PASHA-ISP.lan02.inno
[ kraxel: add qemu/error-report.h include to fix osx build failure ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
It provides a better monitor output of the ICP and ICS objects, else
the objects are printed out of order.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICS object uses a post_load() handler which is implicitly relying
on the fact that the internal state of the ICS and ICP objects has
been restored but this is not guaranteed. So, let's move the code
under the post_load() handler of the machine where we know the objects
have been fully restored.
The icp_resend() handler of the XICSFabric QOM interface is also
removed as it is now obsolete.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XICSState classes are not used anymore. They have now been fully
deprecated by the XICSFabric QOM interface. Do the cleanups.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is nothing left related to the XICS object in the realize
functions of the KVMXICSState and XICSState class. So adapt the
interfaces to call these routines directly from the sPAPR machine init
sequence.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is the last step to remove the XICSState abstraction and have the
machine hold all the objects related to interrupts : ICSs and ICPs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_dt_xics() only needs the number of servers to build the device
tree nodes. Let's change the routine interface to reflect that.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also introduce a xics_icp_get() helper to simplify the changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The cpu_setup() handler is currently under the XICSState class but it
really belongs under ICPState as it is setting up an individual vCPU.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The cpu_setup() handler currently takes a 'XICSState *' argument to
grab the kernel ICP file descriptor. This interface can be simplified
by using the 'xics' backlink of the ICP object.
This change is also required by subsequent patches which makes use of
the QOM interface for XICS.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Let's add two new handlers for ICPs. One is to get an ICP object from
a server number and a second is to resend the irqs when needed.
The icp_resend() handler is a temporary workaround needed by the
ics-simple post_load() handler. It will be removed when the post_load
portion can be done at the machine level.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is not used anymore.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is not used anymore now that we have the QOM interface for XICS.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also change the ICPState 'xics' backlink to be a XICSFabric, this
removes the need of using qdev_get_machine() to get the QOM interface
in some of the routines.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add 'ics_get' and 'ics_resend' handlers to the sPAPR machine. These
are relatively simple for a single ICS.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This interface provides two simple handlers. One is to get an ICS
(Interrupt Source Controller) object from an irq number and a second
to resend the irqs when needed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A list of ICS objects was introduced under the XICS object for the
PowerNV machine but, for the sPAPR machine, it brings extra complexity
as there is only a single ICS. To simplify the code, let's add the ICS
pointer under the sPAPR machine and try to reduce the use of this list
where possible.
Also, change the xics_spapr_*() routines to use an ICS object instead
of an XICSState and change their name to reflect that these are
specific to the sPAPR ICS object.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the ICP (Interrupt Controller Presenter) objects are created by
the 'nr_servers' property handler of the XICS object and a class
handler. They are realized in the XICS object realize routine.
Let's simplify the process by creating the ICP objects along with the
XICS object at the machine level.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the ICS (Interrupt Controller Source) object is created and
realized by the init and realize routines of the XICS object, but some
of the parameters are only known at the machine level.
These parameters are passed from the sPAPR machine to the ICS object
in a rather convoluted way using property handlers and a class handler
of the XICS object. The number of irqs required to allocate the IRQ
state objects in the ICS realize routine is one of them.
Let's simplify the process by creating the ICS object along with the
XICS object at the machine level and link the ICS into the XICS list
of ICSs at this level also. In the sPAPR machine, there is only a
single ICS but that will change with the PowerNV machine.
Also, QOMify the creation of the objects and get rid of the
superfluous code.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently xics - the component of the IBM POWER interrupt controller
representing the overall interrupt fabric / architecture is
represented as a descendent of SysBusDevice. However, this is not
really correct - the xics presents nothing in MMIO space so it should
be an "unattached" device in the current QOM model.
Since this device will always be created by the machine type, not created
specifically from the command line, and because it has no migrated state
it should be safe to move it around the device composition tree.
Therefore this patch changes it to a descendent of TYPE_DEVICE, and
makes it an unattached device. So that its reset handler still gets
called correctly, we add a qdev_set_parent_bus() to attach it to
sysbus. It's not really clear that's correct (instead of using
register_reset()) but it appears to a common technique.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[clg corrected problems with reset]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg folded together and updated commit message]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since commit 1d2d974244 "spapr_pci: enumerate and add PCI device tree", QEMU
populates the PCI device tree in the opposite order compared to SLOF.
Before 1d2d974244:
Populating /pci@800000020000000
00 0000 (D) : 1af4 1000 virtio [ net ]
00 0800 (D) : 1af4 1001 virtio [ block ]
00 1000 (D) : 1af4 1009 virtio [ network ]
Populating /pci@800000020000000/unknown-legacy-device@2
7e5294b8 : /pci@800000020000000
7e52b998 : |-- ethernet@0
7e52c0c8 : |-- scsi@1
7e52c7e8 : +-- unknown-legacy-device@2 ok
Since 1d2d974244:
Populating /pci@800000020000000
00 1000 (D) : 1af4 1009 virtio [ network ]
Populating /pci@800000020000000/unknown-legacy-device@2
00 0800 (D) : 1af4 1001 virtio [ block ]
00 0000 (D) : 1af4 1000 virtio [ net ]
7e5e8118 : /pci@800000020000000
7e5ea6a0 : |-- unknown-legacy-device@2
7e5eadb8 : |-- scsi@1
7e5eb4d8 : +-- ethernet@0 ok
This behaviour change is not actually a bug since no assumptions should be
made on DT ordering. But it has no real justification either, other than
being the consequence of the way fdt_add_subnode() inserts new elements
to the front of the FDT rather than adding them to the tail.
This patch reverts to the historical SLOF ordering by walking PCI devices
in reverse order. This reconciles pseries with x86 machine types behavior.
It is expected to make things easier when porting existing applications to
power.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
(slight update to the changelog)
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To allow QEMU to add PCI entries in device tree,
we must have a more exhaustive list of PCI class IDs.
This patch synchronizes as much as possible with
pci_ids.h and add some missing IDs from SLOF.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Move the fallback from qtest_add_data_func_full() to glib-compat.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Similarly to allocation, do it from an inline function. This allows
tests to only use the headers for allocation/free of timer.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
for building a s390-netboot.img) can be found at
http://wiki.qemu-project.org/Features/S390xNetworkBoot
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nH9Y
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20170228' into staging
Network boot for s390x. More information (and instructions
for building a s390-netboot.img) can be found at
http://wiki.qemu-project.org/Features/S390xNetworkBoot
# gpg: Signature made Tue 28 Feb 2017 11:27:18 GMT
# gpg: using RSA key 0xDECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20170228:
pc-bios/s390-ccw.img: rebuild image
pc-bios/s390-ccw: Use the ccw bios to start the network boot
s390x/ipl: Load network boot image
s390x/ipl: Extend S390IPLState to support network boot
elf-loader: Allow late loading of elf
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Aborting on error in bdrv_append() isn't correct. This patch fixes it
and lets the callers handle failures.
Test case 085 needs a reference output update. This is caused by the
reversed order of bdrv_set_backing_hd() and change_parent_backing_link()
in bdrv_append(): When the backing file of the new node is set, the
parent nodes are still pointing to the old top, so the backing blocker
is now initialised with the node name rather than the BlockBackend name.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Not all callers of bdrv_set_backing_hd() know for sure that attaching
the backing file will be allowed by the permission system. Return the
error from the function rather than aborting.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
The HMP command 'qemu-io' is a bit tricky because it wants to work on
the original BlockBackend, but additional permissions could be required.
The details are explained in a comment in the code, but in summary, just
request whatever permissions the current qemu-io command needs.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Management tools need to be able to know about every node in the graph
and need a way to address them. Changing the graph structure was okay
because libvirt doesn't really manage the node level yet, but future
libvirt versions need to deal with both new and old version of qemu.
This new option to blockdev-commit allows the client to set a node-name
for the automatically inserted filter driver, and at the same time
serves as a witness for a future libvirt that this version of qemu does
automatically insert a filter driver.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Management tools need to be able to know about every node in the graph
and need a way to address them. Changing the graph structure was okay
because libvirt doesn't really manage the node level yet, but future
libvirt versions need to deal with both new and old version of qemu.
This new option to blockdev-mirror allows the client to set a node-name
for the automatically inserted filter driver, and at the same time
serves as a witness for a future libvirt that this version of qemu does
automatically insert a filter driver.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
In some cases, we want to remove op blockers on intermediate nodes
before the whole block job transaction has completed (because they block
restoring the final graph state during completion). Provide a function
for this.
The whole block job lifecycle is a bit messed up and it's hard to
actually do all things in the right order, but I'll leave simplifying
this for another day.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Backing files are somewhat special compared to other kinds of children
because they are attached and detached using bdrv_set_backing_hd()
rather than the normal set of functions, which does a few more things
like setting backing blockers, toggling the BDRV_O_NO_BACKING flag,
setting parent_bs->backing_file, etc.
These special features are a reason why change_parent_backing_link()
can't handle backing files yet. With abstracting the additional features
into .attach/.detach callbacks, we get a step closer to a function that
can actually deal with this.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Block jobs don't actually do I/O through the the reference they create
with block_job_add_bdrv(), but they might want to use the permisssion
system to express what the block job does to intermediate nodes. This
adds permissions to block_job_add_bdrv() to provide the means to request
permissions.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
When the parents' child links are updated in bdrv_append() or
bdrv_replace_in_backing_chain(), this should affect all child links of
BlockBackends or other nodes, but not on child links held for other
purposes (like for setting permissions). This patch allows to control
the behaviour per BdrvChildRole.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
For meaningful error messages in the permission system, we need to get
some human-readable description of the parent of a BdrvChild.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
This functions creates a BlockBackend internally, so the block jobs need
to tell it what they want to do with the BB.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
By default, don't allow another writer for block devices that are
attached to a guest device. For the cases where this setup is intended
(e.g. using a cluster filesystem on the disk), the new option can be
used to allow it.
This change affects only devices using DEFINE_BLOCK_PROPERTIES().
Devices directly using DEFINE_PROP_DRIVE() still accept writers
unconditionally.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
This makes all device emulations with a qdev drive property request
permissions on their BlockBackend. The only thing we block at this point
is resizing images for some devices that can't support it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Some devices allow a media change between read-only and read-write
media. They need to adapt the permissions in their .change_media_cb()
implementation, which can fail. So add an Error parameter to the
function.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
blk_new_open() is a convenience function that processes flags rather
than QDict options as a simple way to just open an image file.
In order to keep it convenient in the future, it must automatically
request the necessary permissions. This can easily be inferred from the
flags for read and write, but we need another flag that tells us whether
to get the resize permission.
We can't just always request it because that means that no block jobs
can run on the resulting BlockBackend (which is something that e.g.
qemu-img commit wants to do), but we also can't request it never because
most of the .bdrv_create() implementations call blk_truncate().
The solution is to introduce another flag that is passed by all users
that want to resize the image.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Now that blk_insert_bs() requests the BlockBackend permissions for the
node it attaches to, it can fail. Instead of aborting, pass the errors
to the callers.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
We want every user to be specific about the permissions it needs, so
we'll pass the initial permissions as parameters to blk_new(). A user
only needs to call blk_set_perm() if it wants to change the permissions
after the fact.
The permissions are stored in the BlockBackend and applied whenever a
BlockDriverState should be attached in blk_insert_bs().
This does not include actually choosing the right set of permissions
everywhere yet. Instead, the usual FIXME comment is added to each place
and will be addressed in individual patches.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
The BlockBackend can now store the permissions that its user requires.
This is necessary because nodes can be ejected from or inserted into a
BlockBackend and all of these operations must make sure that the user
still gets what it requested initially.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
vvfat is the last remaining driver that can have children, but doesn't
implement .bdrv_child_perm() yet. The default handlers aren't suitable
here, so let's implement a very simple driver-specific one that protects
the internal child from being used by other users as good as our
permissions permit.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Almost all format drivers have the same characteristics as far as
permissions are concerned: They have one or more children for storing
their own data and, more importantly, metadata (can be written to and
grow even without external write requests, must be protected against
other writers and present consistent data) and optionally a backing file
(this is just data, so like for a filter, it only depends on what the
parent nodes need).
This provides a default implementation that can be shared by most of
our format drivers.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Most filters need permissions related to read and write for their
children, but only if the node has a parent that wants to use the same
operation on the filter. The same is true for resize.
This adds a default implementation that simply forwards all necessary
permissions to all children of the node and leaves the other permissions
unchanged.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
In many cases, the required permissions of one node on its children
depend on what its parents require from it. For example, the raw format
or most filter drivers only need to request consistent reads if that's
something that one of their parents wants.
In order to achieve this, this patch introduces two new BlockDriver
callbacks. The first one lets drivers first check (recursively) whether
the requested permissions can be set; the second one actually sets the
new permission bitmask.
Also add helper functions that drivers can use in their implementation
of the callbacks to update their permissions on a specific child.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
When attaching a node as a child to a new parent, the required and
shared permissions for this parent are checked against all other parents
of the node now, and an error is returned if there is a conflict.
This allows error returns to a function that previously always
succeeded, and the same is true for quite a few callers and their
callers. Converting all of them within the same patch would be too much,
so for now everyone tells that they don't need any permissions and allow
everyone else to do anything. This way we can use &error_abort initially
and convert caller by caller to pass actual permission requirements and
implement error handling.
All these places are marked with FIXME comments and it will be the job
of the next patches to clean them up again.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
It will have to return an error soon, so prepare the callers for it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
This patch defines the permission categories that will be used by the
new op blocker system.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
- a fix to a minor bug reported by Coverity
- throttling support in the local backend (command line only)
-----BEGIN PGP SIGNATURE-----
iEYEABECAAYFAli1Q64ACgkQAvw66wEB28I5yQCePbLPSOtHO4LJGc2E973L7vH2
hQIAnReLFevyNN6BpivucP2/0YmAIKSi
=uTYd
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/for-upstream' into staging
This pull request brings:
- a fix to a minor bug reported by Coverity
- throttling support in the local backend (command line only)
# gpg: Signature made Tue 28 Feb 2017 09:32:30 GMT
# gpg: using DSA key 0x02FC3AEB0101DBC2
# gpg: Good signature from "Greg Kurz <groug@kaod.org>"
# gpg: aka "Greg Kurz <groug@free.fr>"
# gpg: aka "Greg Kurz <gkurz@linux.vnet.ibm.com>"
# gpg: aka "Gregory Kurz (Groug) <groug@free.fr>"
# gpg: aka "[jpeg image of size 3330]"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 2BD4 3B44 535E C0A7 9894 DBA2 02FC 3AEB 0101 DBC2
* remotes/gkurz/tags/for-upstream:
throttle: factor out duplicate code
fsdev: add IO throttle support to fsdev devices
9pfs: fix v9fs_lock error case
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the bcm2835_sdhost and bcm2835_gpio to the BCM2835 platform.
For supporting the SD controller selection (alternate function of GPIOs
48-53), the bcm2835_gpio now exposes an sdbus.
It also has a link to both the sdbus of sdhci and sdhost controllers,
and the card is reparented from one bus to another when the alternate
function of GPIOs 48-53 is modified.
Signed-off-by: Clement Deschamps <clement.deschamps@antfield.fr>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1488293711-14195-5-git-send-email-peter.maydell@linaro.org
Message-id: 20170224164021.9066-5-clement.deschamps@antfield.fr
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the BCM2835 GPIO controller.
It currently implements:
- The 54 GPIOs as outputs (qemu_irq)
- The SD controller selection via alternate function of GPIOs 48-53
Signed-off-by: Clement Deschamps <clement.deschamps@antfield.fr>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1488293711-14195-4-git-send-email-peter.maydell@linaro.org
Message-id: 20170224164021.9066-4-clement.deschamps@antfield.fr
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a new function sdbus_reparent_card() in sd core for reparenting
a card from a SDBus to another one.
This function is required by the raspi platform, where the two SD
controllers can be dynamically switched.
Signed-off-by: Clement Deschamps <clement.deschamps@antfield.fr>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1488293711-14195-3-git-send-email-peter.maydell@linaro.org
Message-id: 20170224164021.9066-3-clement.deschamps@antfield.fr
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added a doc comment to the header file; changed to
use new behaviour of qdev_set_parent_bus()]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To Save and Restore ICC_SRE_EL1 register introduce vmstate
subsection and load only if non-zero.
Also initialize icc_sre_el1 with to 0x7 in pre_load
function.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1487850673-26455-3-git-send-email-vijay.kilari@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virtio_mmio.h would be deleted; I am leaving it in though it was a
mistake to add it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the stm32f205 SoC to create the armv7m object directly
rather than via the armv7m_init() wrapper. This fits better
with the SoC model's very QOMified design.
In particular this means we can push loading the guest image
out to the top level board code where it belongs, rather
than the SoC object having a QOM property for the filename
to load.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-11-git-send-email-peter.maydell@linaro.org
The SysTick timer isn't really part of the NVIC proper;
we just modelled it that way back when we couldn't
easily have devices that only occupied a small chunk
of a memory region. Split it out into its own device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1487604965-23220-10-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Instead of the bitband device doing a cpu_physical_memory_read/write,
make it take a MemoryRegion which specifies where it should be
accessing, and use address_space_read/write to access the
corresponding AddressSpace.
Since this entails pretty much a rewrite, convert away from
old_mmio in the process.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-8-git-send-email-peter.maydell@linaro.org
Make the ARMv7M object take a memory region link which it uses
to wire up the bitband rather than having them always put
themselves in the system address space.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-6-git-send-email-peter.maydell@linaro.org
Create a proper QOM object for the armv7m container, which
holds the CPU, the NVIC and the bitband regions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-4-git-send-email-peter.maydell@linaro.org
Move the NVICState struct definition into a header, so we can
embed it into other QOM objects like SoCs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-3-git-send-email-peter.maydell@linaro.org
Abstract the "load kernel" code out of armv7m_init() into its own
function. This includes the registration of the CPU reset function,
to parallel how we handle this for A profile cores.
We make the function public so that boards which choose to
directly instantiate an ARMv7M device object can call it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-2-git-send-email-peter.maydell@linaro.org
This adds the BCM2835 SDHost controller from Arasan.
Signed-off-by: Clement Deschamps <clement.deschamps@antfield.fr>
Message-id: 20170224164021.9066-2-clement.deschamps@antfield.fr
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In 2.9 ITS will block save/restore and migration use cases. As such,
let's introduce a user option that allows to turn its instantiation
off, along with GICv3. With the "its" option turned false, migration
will be possible, obviously at the expense of MSI support (with GICv3).
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1487681108-14452-1-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Recent vanilla Raspberry Pi kernels started to make use of
the hardware random number generator in BCM2835 SoC. As a
result, those kernels wouldn't work anymore under QEMU
but rather just freeze during the boot process.
This patch implements a trivial BCM2835 compatible RNG,
and adds it as a peripheral to BCM2835 platform, which
allows to boot a vanilla Raspberry Pi kernel under Qemu.
Changes since v1:
* Prevented guest from writing [31..20] bits in rng_status
* Removed redundant minimum_version_id_old
* Added field entries for the state
* Changed realize function to reset
Signed-off-by: Marcin Chojnacki <marcinch7@gmail.com>
Message-id: 20170210210857.47893-1-marcinch7@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The kernel can't do UFFDIO_ZEROPAGE for huge pages, so we have
to allocate a temporary (always zero) page and use UFFDIO_COPYPAGE
on it.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20170224182844.32452-9-dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Now we deal with normal size pages and huge pages we need
to tell the place handlers the size we're dealing with
and make sure the temporary page is large enough.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20170224182844.32452-8-dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Record the largest page size in use; we'll need it soon for allocating
temporary buffers.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20170224182844.32452-7-dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Create ram_block_discard_range in exec.c to replace
postcopy_ram_discard_range and most of ram_discard_range.
Those two routines are a bit of a weird combination, and
ram_discard_range is about to get more complex for hugepages.
It's OS dependent code (so shouldn't be in migration/ram.c) but
it needs quite a bit of the innards of RAMBlock so doesn't belong in
the os*.c.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20170224182844.32452-5-dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Replace the host page-size in the 'advise' command by a pagesize
summary bitmap; if the VM is just using normal RAM then
this will be exactly the same as before, however if they're using
huge pages they'll be different, and thus:
a) Migration from/to old qemu's that don't understand huge pages
will fail early.
b) Migrations with different size RAMBlocks will also fail early.
This catches it very early; earlier than the detailed per-block
check in the next patch.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170224182844.32452-2-dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Commit a3a3d8c7 introduced a segfault bug while checking for
'dc->vmsd->unmigratable' which caused QEMU to crash when trying to add
devices which do no set their 'dc->vmsd' yet while initialization.
Place a 'dc->vmsd' check prior to it so that we do not segfault for
such devices.
NOTE: This doesn't compromise the functioning of --only-migratable
option as all the unmigratable devices do set their 'dc->vmsd'.
Introduce a new function check_migratable() and move the
only_migratable check inside it, also use stubs to avoid user-mode qemu
build failures.
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1487009088-23891-1-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Make VMS_ARRAY_OF_POINTER cope with null pointers. Previously the
reward for trying to migrate an array with some null pointers in it was
an illegal memory access, that is a swift and painless death of the
process. Let's make vmstate cope with this scenario.
The general approach is, when we encounter a null pointer (element),
instead of following the pointer to save/load the data behind it, we
save/load a placeholder. This way we can detect if we expected a null
pointer at the load side but not null data was saved instead.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Guenther Hutzl <hutzl@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170222160119.52771-4-pasic@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The current QEMU ROM infrastructure rejects late loading of ROMs.
And ELFs are currently loaded as ROM, this prevents delayed loading
of ELFs. So when loading ELF, allow the user to specify if ELF should
be loaded as ROM or not.
If an ELF is not loaded as ROM, then they are not restored on a
guest reboot/reset and so its upto the user to handle the reloading.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This patch removes the redundant throttle code that was present in
block and fsdev device files. Now the common code is moved
to a single file.
Signed-off-by: Pradeep Jagadeesh <pradeep.jagadeesh@huawei.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
(fix indent nit, Greg Kurz)
Signed-off-by: Greg Kurz <groug@kaod.org>
It's still time to wish happy new year!
The Year of the Rooster will begin on January 28, 2017!
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Helper function (and DisplayChangeListenerOps ptr) to disable scanouts.
Replaces using dpy_gl_scanout_texture with 0x0 size and no texture
specified.
Allows cleanups to make the io and gfx emulation code more readable.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1487669841-13668-3-git-send-email-kraxel@redhat.com
We'll add a variant which accepts dmabufs soon. Change
the name so we can easily disturgish the two variants.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1487669841-13668-2-git-send-email-kraxel@redhat.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=OYgF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches
# gpg: Signature made Fri 24 Feb 2017 18:08:26 GMT
# gpg: using RSA key 0x7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream:
tests: Use opened block node for block job tests
vvfat: Use opened node as backing file
block: Add bdrv_new_open_driver()
block: Factor out bdrv_open_driver()
block: Use BlockBackend for image probing
block: Factor out bdrv_open_child_bs()
block: Attach bs->file only during .bdrv_open()
block: Pass BdrvChild to bdrv_truncate()
mirror: Resize active commit base in mirror_run()
qcow2: Use BB for resizing in qcow2_amend_options()
blockdev: Use BlockBackend to resize in qmp_block_resize()
iotests: Fix another race in 030
qemu-img: Improve documentation for PREALLOC_MODE_FALLOC
qemu-img: Truncate before full preallocation
qemu-img: Add tests for raw image preallocation
qemu-img: Do not truncate before preallocation
qemu-iotests: redirect nbd server stdout to /dev/null
qemu-iotests: add ability to exclude certain protocols from tests
qemu-iotests: Test 137 only supports 'file' protocol
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- cleanups, fixes and improvements
- program check loop detection (useful with the corresponding kernel
patch)
- wire up virtio-crypto for ccw
- and finally support many virtqueues for virtio-ccw
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uM3N
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20170224' into staging
A selection of s390x patches:
- cleanups, fixes and improvements
- program check loop detection (useful with the corresponding kernel
patch)
- wire up virtio-crypto for ccw
- and finally support many virtqueues for virtio-ccw
# gpg: Signature made Fri 24 Feb 2017 09:19:19 GMT
# gpg: using RSA key 0xDECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20170224:
s390x/css: handle format-0 TIC CCW correctly
s390x/arch_dump: pass cpuid into notes sections
s390x/arch_dump: use proper note name and note size
virtio-ccw: support VIRTIO_QUEUE_MAX virtqueues
s390x: bump ADAPTER_ROUTES_MAX_GSI
virtio-ccw: check flic->adapter_routes_max_batch
s390x: add property adapter_routes_max_batch
virtio-ccw: Check the number of vqs in CCW_CMD_SET_IND
virtio-ccw: add virtio-crypto-ccw device
virtio-ccw: handle virtio 1 only devices
s390x/flic: fail migration on source already
s390x/kvm: detect some program check loops
s390x/s390-virtio: get rid of DPRINTF
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=o8eA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-util-2017-02-23' into staging
option cutils: Fix and clean up number conversions
# gpg: Signature made Thu 23 Feb 2017 19:41:17 GMT
# gpg: using RSA key 0x3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-util-2017-02-23: (24 commits)
option: Fix checking of sizes for overflow and trailing crap
util/cutils: Change qemu_strtosz*() from int64_t to uint64_t
util/cutils: Return qemu_strtosz*() error and value separately
util/cutils: Let qemu_strtosz*() optionally reject trailing crap
qemu-img: Wrap cvtnum() around qemu_strtosz()
test-cutils: Drop suffix from test_qemu_strtosz_simple()
test-cutils: Use qemu_strtosz() more often
util/cutils: Drop QEMU_STRTOSZ_DEFSUFFIX_* macros
util/cutils: New qemu_strtosz()
util/cutils: Rename qemu_strtosz() to qemu_strtosz_MiB()
util/cutils: New qemu_strtosz_metric()
test-cutils: Cover qemu_strtosz() around range limits
test-cutils: Cover qemu_strtosz() with trailing crap
test-cutils: Cover qemu_strtosz() invalid input
test-cutils: Add missing qemu_strtosz()... endptr checks
option: Fix to reject invalid and overflowing numbers
util/cutils: Clean up control flow around qemu_strtol() a bit
util/cutils: Clean up variable names around qemu_strtol()
util/cutils: Rename qemu_strtoll(), qemu_strtoull()
util/cutils: Rewrite documentation of qemu_strtol() & friends
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This function allows to create more or less normal BlockDriverStates
even for BlockDrivers that aren't globally registered (e.g. helper
filters for block jobs).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This introduces support to the cputlb API for flushing all CPUs TLBs
with one call. This avoids the need for target helpers to iterate
through the vCPUs themselves.
An additional variant of the API (_synced) will cause the source vCPUs
work to be scheduled as "safe work". The result will be all the flush
operations will be complete by the time the originating vCPU executes
its safe work. The calling implementation can either end the TB
straight away (which will then pick up the cpu->exit_request on
entering the next block) or defer the exit until the architectural
sync point (usually a barrier instruction).
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The main use case for tlb_reset_dirty is to set the TLB_NOTDIRTY flags
in TLB entries to force the slow-path on writes. This is used to mark
page ranges containing code which has been translated so it can be
invalidated if written to. To do this safely we need to ensure the TLB
entries in question for all vCPUs are updated before we attempt to run
the code otherwise a race could be introduced.
To achieve this we atomically set the flag in tlb_reset_dirty_range and
take care when setting it when the TLB entry is filled.
On 32 bit systems attempting to emulate 64 bit guests we don't even
bother as we might not have the atomic primitives available. MTTCG is
disabled in this case and can't be forced on. The copy_tlb_helper
function helps keep the atomic semantics in one place to avoid
confusion.
The dirty helper function is made static as it isn't used outside of
cputlb.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
This converts the remaining TLB flush routines to use async work when
detecting a cross-vCPU flush. The only minor complication is having to
serialise the var_list of MMU indexes into a form that can be punted
to an asynchronous job.
The pending_tlb_flush field on QOM's CPU structure also becomes a
bitfield rather than a boolean.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
While the vargs approach was flexible the original MTTCG ended up
having munge the bits to a bitmap so the data could be used in
deferred work helpers. Instead of hiding that in cputlb we push the
change to the API to make it take a bitmap of MMU indexes instead.
For ARM some the resulting flushes end up being quite long so to aid
readability I've tended to move the index shifting to a new line so
all the bits being or-ed together line up nicely, for example:
tlb_flush_page_by_mmuidx(other_cs, pageaddr,
(1 << ARMMMUIdx_S1SE1) |
(1 << ARMMMUIdx_S1SE0));
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
[AT: SPARC parts only]
Reviewed-by: Artyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
[PM: ARM parts only]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Some architectures allow to flush the tlb of other VCPUs. This is not a problem
when we have only one thread for all VCPUs but it definitely needs to be an
asynchronous work when we are in true multithreaded work.
We take the tb_lock() when doing this to avoid racing with other threads
which may be invalidating TB's at the same time. The alternative would
be to use proper atomic primitives to clear the tlb entries en-mass.
This patch doesn't do anything to protect other cputlb function being
called in MTTCG mode making cross vCPU changes.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
[AJB: remove need for g_malloc on defer, make check fixes, tb_lock]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
There are now only two uses of the global exit_request left.
The first ensures we exit the run_loop when we first start to process
pending work and in the kick handler. This is just as easily done by
setting the first_cpu->exit_request flag.
The second use is in the round robin kick routine. The global
exit_request ensured every vCPU would set its local exit_request and
cause a full exit of the loop. Now the iothread isn't being held while
running we can just rely on the kick handler to push us out as intended.
We lightly re-factor the main vCPU thread to ensure cpu->exit_requests
cause us to exit the main loop and process any IO requests that might
come along. As an cpu->exit_request may legitimately get squashed
while processing the EXCP_INTERRUPT exception we also check
cpu->queued_work_first to ensure queued work is expedited as soon as
possible.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
This finally allows TCG to benefit from the iothread introduction: Drop
the global mutex while running pure TCG CPU code. Reacquire the lock
when entering MMIO or PIO emulation, or when leaving the TCG loop.
We have to revert a few optimization for the current TCG threading
model, namely kicking the TCG thread in qemu_mutex_lock_iothread and not
kicking it in qemu_cpu_kick. We also need to disable RAM block
reordering until we have a more efficient locking mechanism at hand.
Still, a Linux x86 UP guest and my Musicpal ARM model boot fine here.
These numbers demonstrate where we gain something:
20338 jan 20 0 331m 75m 6904 R 99 0.9 0:50.95 qemu-system-arm
20337 jan 20 0 331m 75m 6904 S 20 0.9 0:26.50 qemu-system-arm
The guest CPU was fully loaded, but the iothread could still run mostly
independent on a second core. Without the patch we don't get beyond
32206 jan 20 0 330m 73m 7036 R 82 0.9 1:06.00 qemu-system-arm
32204 jan 20 0 330m 73m 7036 S 21 0.9 0:17.03 qemu-system-arm
We don't benefit significantly, though, when the guest is not fully
loading a host CPU.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-Id: <1439220437-23957-10-git-send-email-fred.konrad@greensocs.com>
[FK: Rebase, fix qemu_devices_reset deadlock, rm address_space_* mutex]
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
[EGC: fixed iothread lock for cpu-exec IRQ handling]
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: -smp single-threaded fix, clean commit msg, BQL fixes]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Pranith Kumar <bobby.prani@gmail.com>
[PM: target-arm changes]
Acked-by: Peter Maydell <peter.maydell@linaro.org>
..and make the definition local to cpus. In preparation for MTTCG the
concept of a global tcg_current_cpu will no longer make sense. However
we still need to keep track of it in the single-threaded case to be able
to exit quickly when required.
qemu_cpu_kick_no_halt() moves and becomes qemu_cpu_kick_rr_cpu() to
emphasise its use-case. qemu_cpu_kick now kicks the relevant cpu as
well as qemu_kick_rr_cpu() which will become a no-op in MTTCG.
For the time being the setting of the global exit_request remains.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Pranith Kumar <bobby.prani@gmail.com>
We know there will be cases where MTTCG won't work until additional work
is done in the front/back ends to support. It will however be useful to
be able to turn it on.
As a result MTTCG will default to off unless the combination is
supported. However the user can turn it on for the sake of testing.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
[AJB: move to -accel tcg,thread=multi|single, defaults]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
This pull request has:
* Yet more POWER9 instruction implementations
* Some extensions to the softfloat code which are necesssary for
some of those instructions
* Some preliminary patches in preparation for POWER9 softmmu
implementation
* Igor Mammedov's cleanups to unify hotplug cpu handling across
architectures
* Assorted bugfixes
The softfloat and cpu hotplug changes aren't entirely ppc specific (in
fact the hotplug stuff contains some pc specific patches). However
they're included here because ppc is one of the main beneficiaries,
and the series depend on some ppc specific patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJYrS/bAAoJEGw4ysog2bOSJ3MP/AjoTGTP5MHPwWBZKAxpEtie
vEXudVbOelr3QV06vHMH4YHVAncuzt9Hmz/RDgs5Uynp4vLdmEo5IdiFP9PMjrFg
oMAndku9icU8PG+XNF5pNrKy10n6k8dVRBR/19UxnRWMuxywOZO208WkICF/6kDK
IpFT96MubqbReLcVhdl2N8d2rP7/lRQmz6aPxhRLFBuAe8iheAQLq/QeZLIZaWEJ
i4mPWVu/CDYP9nMAgv56MW0yY5p2o5MCh+f80+7jvKXZBoeo83KOTaZeZbGb/byr
rCfyLTR24tj6WUGRvzyB+FJ8rbWKcox4UCx17239gAjXtLxhlYaQDo28S5gwinpQ
b/CaEgb8x2kl97tZT/M1mamr7PdFxachCA20oizguwFJ9oeukAPUvkVBpEtVYK8K
a+VrRHxVJwSi/ZD3N6WRZMXR4D+Oc8DcXoEzMu4CFtIzQ/WJroZCa4JCcdv4N1nw
9u1m+C2QbQ9sGBtTSGCy0KZyT3sZHoFT6aD4zpkV7s3BJKk+AXSLRpL4z8FP2sDB
Wh/Qk5q06P1pPZzvuU9QJmrpIE9EFcOQW4IQhyViut+BXzBlp7cWxeGcPM5PuJ7V
6FcMSchZeVOiLi9Y51csluDrecTKIQ3yFEgLW7j50Lg/WqmdwlwkcW39MzlWgjgQ
OIoVgvGmGovPTGIIYyY9
=bsJJ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170222' into staging
ppc patch queue for 2017-02-22
This pull request has:
* Yet more POWER9 instruction implementations
* Some extensions to the softfloat code which are necesssary for
some of those instructions
* Some preliminary patches in preparation for POWER9 softmmu
implementation
* Igor Mammedov's cleanups to unify hotplug cpu handling across
architectures
* Assorted bugfixes
The softfloat and cpu hotplug changes aren't entirely ppc specific (in
fact the hotplug stuff contains some pc specific patches). However
they're included here because ppc is one of the main beneficiaries,
and the series depend on some ppc specific patches.
# gpg: Signature made Wed 22 Feb 2017 06:29:47 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170222: (43 commits)
hw/ppc/ppc405_uc.c: Avoid integer overflows
hw/ppc/spapr: Check for valid page size when hot plugging memory
target-ppc: fix Book-E TLB matching
hw/net/spapr_llan: 6 byte mac address device tree entry
machine: replace query_hotpluggable_cpus() callback with has_hotpluggable_cpus flag
machine: unify [pc_|spapr_]query_hotpluggable_cpus() callbacks
spapr: reuse machine->possible_cpus instead of cores[]
change CPUArchId.cpu type to Object*
pc: pass apic_id to pc_find_cpu_slot() directly so lookup could be done without CPU object
pc: calculate topology only once when possible_cpus is initialised
pc: move pcms->possible_cpus init out of pc_cpus_init()
machine: move possible_cpus to MachineState
hw/pci-host/prep: Do not use hw_error() in realize function
target/ppc/POWER9: Direct all instr and data storage interrupts to the hypv
target/ppc/POWER9: Adapt LPCR handling for POWER9
target/ppc/POWER9: Add ISAv3.00 MMU definition
target/ppc: Fix LPCR DPFD mask define
target-ppc: Add xscvqpudz and xscvqpuwz instructions
target-ppc: Implement round to odd variants of quad FP instructions
softfloat: Add float128_to_uint32_round_to_zero()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The maximal number of virtqueues per device can be limited on a per
transport basis. For virtio-ccw this limit is defined by
VIRTIO_CCW_QUEUE_MAX, however the limitation used to come form the
number of adapter routes supported by flic (via notifiers).
Recently the limitation of the flic was adjusted so that it can
accommodate VIRTIO_QUEUE_MAX queues, and is in the meanwhile checked for
separately too.
Let us remove the transport specific limitation of virtio-ccw by
dropping VIRTIO_CCW_QUEUE_MAX and using VIRTIO_QUEUE_MAX instead.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's increase ADAPTER_ROUTES_MAX_GSI to VIRTIO_QUEUE_MAX which is the
largest demand foreseeable at the moment. Let us add a compatibility
macro for the previous machines so client code can maintain backwards
migration compatibility
To not mess up migration compatibility for virtio-ccw
VIRTIO_CCW_QUEUE_MAX is left at it's current value, and will be dropped
when virtio-ccw is converted to use the capability of the flic
introduced by this patch.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
To make virtio-ccw supports more that 64 virtqueues we will have to
increase ADAPTER_ROUTES_MAX_GSI which is currently limiting the number if
possible adapter routes. Of course increasing the number of supported
routes can break backwards migration.
Let us introduce a compatibility property adapter_routes_max_batch so
client code can use the some old limit if in compatibility mode and
retain the migration compatibility.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This will permit its use in parse_option_size().
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com> (maintainer:X86)
Cc: Kevin Wolf <kwolf@redhat.com> (supporter:Block layer core)
Cc: Max Reitz <mreitz@redhat.com> (supporter:Block layer core)
Cc: qemu-block@nongnu.org (open list:Block layer core)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1487708048-2131-24-git-send-email-armbru@redhat.com>
This makes qemu_strtosz(), qemu_strtosz_mebi() and
qemu_strtosz_metric() similar to qemu_strtoi64(), except negative
values are rejected.
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com> (maintainer:X86)
Cc: Kevin Wolf <kwolf@redhat.com> (supporter:Block layer core)
Cc: Max Reitz <mreitz@redhat.com> (supporter:Block layer core)
Cc: qemu-block@nongnu.org (open list:Block layer core)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1487708048-2131-23-git-send-email-armbru@redhat.com>
Most callers of qemu_strtosz_suffix() pass QEMU_STRTOSZ_DEFSUFFIX_B.
Capture the pattern in new qemu_strtosz().
Inline qemu_strtosz_suffix() into its only remaining caller.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1487708048-2131-17-git-send-email-armbru@redhat.com>
With qemu_strtosz(), no suffix means mebibytes. It's used rarely.
I'm going to add a similar function where no suffix means bytes.
Rename qemu_strtosz() to qemu_strtosz_MiB() to make the name
qemu_strtosz() available for the new function.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1487708048-2131-16-git-send-email-armbru@redhat.com>
To parse numbers with metric suffixes, we use
qemu_strtosz_suffix_unit(nptr, &eptr, QEMU_STRTOSZ_DEFSUFFIX_B, 1000)
Capture this in a new function for legibility:
qemu_strtosz_metric(nptr, &eptr)
Replace test_qemu_strtosz_suffix_unit() by test_qemu_strtosz_metric().
Rename qemu_strtosz_suffix_unit() to do_strtosz() and give it internal
linkage.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1487708048-2131-15-git-send-email-armbru@redhat.com>
The name qemu_strtoll() suggests conversion to long long, but it
actually converts to int64_t. Rename to qemu_strtoi64().
The name qemu_strtoull() suggests conversion to unsigned long long,
but it actually converts to uint64_t. Rename to qemu_strtou64().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1487708048-2131-7-git-send-email-armbru@redhat.com>
Curiously, unrealize() is not being used, but it seems more
appropriate than handle_destroy() together with realize(). It is more
ubiquitous destroy name in qemu code base and may throw errors.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20170221141451.28305-25-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The icount interrupt flag and tcg_exit_req serve almost the same
purpose, let's make them completely the same.
The former TB_EXIT_REQUESTED and TB_EXIT_ICOUNT_EXPIRED cases are
unified, since we can distinguish them from the value of the
interrupt flag.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Generic helper machine_query_hotpluggable_cpus() replaced
target specific query_hotpluggable_cpus() callbacks so
there is no need in it anymore. However inon NULL callback
value is used to detect/report hotpluggable cpus support,
therefore it can be removed completely.
Replace it with MachineClass.has_hotpluggable_cpus boolean
which is sufficient for the task.
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
